[ARM] pxa/balloon3: PCMCIA Support

This driver adds support for the on-board CF socket.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

2 files changed, 31 insertions, 18 deletions

diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index 572525c26ca..91ad56d6e92 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -88,6 +88,18 @@ static unsigned long balloon3_pin_config[] __initdata = {
 	/* USB Host */
 	GPIO88_USBH1_PWR,
 	GPIO89_USBH1_PEN,
+
+	/* PC Card */
+	GPIO48_nPOE,
+	GPIO49_nPWE,
+	GPIO50_nPIOR,
+	GPIO51_nPIOW,
+	GPIO85_nPCE_1,
+	GPIO54_nPCE_2,
+	GPIO79_PSKTSEL,
+	GPIO55_nPREG,
+	GPIO56_nPWAIT,
+	GPIO57_nIOIS16,
 };
 
 /******************************************************************************
@@ -405,7 +417,6 @@ static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
 					balloon3_irq_enabled;
-
 	do {
 		/* clear useless edge notification */
 		if (desc->chip->ack)
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h
index 1a741065045..d5dcf750c1e 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/include/mach/balloon3.h
@@ -26,10 +26,12 @@ enum balloon3_features {
 #define BALLOON3_FPGA_VIRT	(0xf1000000)	/* as per balloon2 */
 #define BALLOON3_FPGA_LENGTH	0x01000000
 
-/* FPGA/CPLD registers */
-#define BALLOON3_PCMCIA0_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
-/* fixme - same for now */
-#define BALLOON3_PCMCIA1_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
+/* FPGA / CPLD registers for CF socket */
+#define	BALLOON3_CF_STATUS_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
+#define	BALLOON3_CF_CONTROL_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
+/* FPGA / CPLD version register */
+#define	BALLOON3_FPGA_VER		(BALLOON3_FPGA_VIRT + 0x00e0001c)
+
 #define BALLOON3_NANDIO_IO_REG		(BALLOON3_FPGA_VIRT + 0x00e00000)
 /* fpga/cpld interrupt control register */
 #define BALLOON3_INT_CONTROL_REG	(BALLOON3_FPGA_VIRT + 0x00e0000C)
@@ -41,6 +43,19 @@ enum balloon3_features {
 #define BALLOON3_SAMOSA_DATA_REG	(BALLOON3_FPGA_VIRT + 0x00c00004)
 #define BALLOON3_SAMOSA_STATUS_REG	(BALLOON3_FPGA_VIRT + 0x00c0001c)
 
+/* CF Status Register bits (read-only) bits */
+#define BALLOON3_CF_nIRQ		(1 << 0)
+#define BALLOON3_CF_nSTSCHG_BVD1	(1 << 1)
+
+/* CF Control Set Register bits / CF Control Clear Register bits (write-only) */
+#define BALLOON3_CF_RESET		(1 << 0)
+#define BALLOON3_CF_ENABLE		(1 << 1)
+#define BALLOON3_CF_ADD_ENABLE		(1 << 2)
+
+/* CF Interrupt sources */
+#define BALLOON3_BP_CF_NRDY_IRQ		BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ		BALLOON3_IRQ(1)
+
 /* GPIOs for irqs */
 #define BALLOON3_GPIO_AUX_NIRQ		(94)
 #define BALLOON3_GPIO_CODEC_IRQ		(95)
@@ -58,16 +73,6 @@ enum balloon3_features {
 #define BALLOON3_INT_S0_IRQ		(1 << 0)  /* PCMCIA 0 IRQ */
 #define BALLOON3_INT_S0_STSCHG		(1 << 1)  /* PCMCIA 0 status changed */
 
-/* CF Status Register */
-#define BALLOON3_PCMCIA_nIRQ		(1 << 0)  /* IRQ / ready signal */
-#define BALLOON3_PCMCIA_nSTSCHG_BVD1	(1 << 1)
-					/* VDD sense / card status changed */
-
-/* CF control register (write) */
-#define BALLOON3_PCMCIA_RESET		(1 << 0)   /* Card reset signal */
-#define BALLOON3_PCMCIA_ENABLE		(1 << 1)
-#define BALLOON3_PCMCIA_ADD_ENABLE	(1 << 2)
-
 /* CPLD (and FPGA) interface definitions */
 #define CPLD_LCD0_DATA_SET             0x00
 #define CPLD_LCD0_DATA_CLR             0x10
@@ -132,9 +137,6 @@ enum balloon3_features {
 /* Balloon3 Interrupts */
 #define BALLOON3_IRQ(x)		(IRQ_BOARD_START + (x))
 
-#define BALLOON3_BP_CF_NRDY_IRQ	BALLOON3_IRQ(0)
-#define BALLOON3_BP_NSTSCHG_IRQ	BALLOON3_IRQ(1)
-
 #define BALLOON3_AUX_NIRQ	IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
 #define BALLOON3_CODEC_IRQ	IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
 #define BALLOON3_S0_CD_IRQ	IRQ_GPIO(BALLOON3_GPIO_S0_CD)