Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

19 files changed, 293 insertions, 21 deletions

diff --git a/arch/sh/boards/Kconfig b/arch/sh/boards/Kconfig
index 7048c03490d..fb5805745ac 100644
--- a/arch/sh/boards/Kconfig
+++ b/arch/sh/boards/Kconfig
@@ -57,6 +57,7 @@ config SH_7724_SOLUTION_ENGINE
 	depends on CPU_SUBTYPE_SH7724
 	select ARCH_REQUIRE_GPIOLIB
 	select SND_SOC_AK4642 if SND_SIMPLE_CARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Select 7724 SolutionEngine if configuring for a Hitachi SH7724
 	  evaluation board.
@@ -140,6 +141,7 @@ config SH_RSK
 	bool "Renesas Starter Kit"
 	depends on CPU_SUBTYPE_SH7201 || CPU_SUBTYPE_SH7203 || \
 	  CPU_SUBTYPE_SH7264 || CPU_SUBTYPE_SH7269
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	 Select this option if configuring for any of the RSK+ MCU
 	 evaluation platforms.
@@ -159,6 +161,7 @@ config SH_SDK7786
 	select NO_IOPORT if !PCI
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select HAVE_SRAM_POOL
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Select SDK7786 if configuring for a Renesas Technology Europe
 	  SH7786-65nm board.
@@ -173,6 +176,7 @@ config SH_SH7757LCR
 	bool "SH7757LCR"
 	depends on CPU_SUBTYPE_SH7757
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 config SH_SH7785LCR
 	bool "SH7785LCR"
@@ -206,6 +210,7 @@ config SH_MIGOR
 	bool "Migo-R"
 	depends on CPU_SUBTYPE_SH7722
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Select Migo-R if configuring for the SH7722 Migo-R platform
           by Renesas System Solutions Asia Pte. Ltd.
@@ -214,6 +219,7 @@ config SH_AP325RXA
 	bool "AP-325RXA"
 	depends on CPU_SUBTYPE_SH7723
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Renesas "AP-325RXA" support.
 	  Compatible with ALGO SYSTEM CO.,LTD. "AP-320A"
@@ -222,6 +228,7 @@ config SH_KFR2R09
 	bool "KFR2R09"
 	depends on CPU_SUBTYPE_SH7724
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  "Kit For R2R for 2009" support.
 
@@ -230,6 +237,7 @@ config SH_ECOVEC
 	depends on CPU_SUBTYPE_SH7724
 	select ARCH_REQUIRE_GPIOLIB
 	select SND_SOC_DA7210 if SND_SIMPLE_CARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Renesas "R0P7724LC0011/21RL (EcoVec)" support.
 
@@ -305,6 +313,7 @@ config SH_MAGIC_PANEL_R2
 	bool "Magic Panel R2"
 	depends on CPU_SUBTYPE_SH7720
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	help
 	  Select Magic Panel R2 if configuring for Magic Panel R2.
 
@@ -316,6 +325,7 @@ config SH_CAYMAN
 config SH_POLARIS
 	bool "SMSC Polaris"
 	select CPU_HAS_IPR_IRQ
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on CPU_SUBTYPE_SH7709
 	help
 	  Select if configuring for an SMSC Polaris development board
@@ -323,6 +333,7 @@ config SH_POLARIS
 config SH_SH2007
 	bool "SH-2007 board"
 	select NO_IOPORT
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on CPU_SUBTYPE_SH7780
 	help
 	  SH-2007 is a single-board computer based around SH7780 chip
@@ -334,6 +345,7 @@ config SH_SH2007
 config SH_APSH4A3A
 	bool "AP-SH4A-3A"
 	select SH_ALPHA_BOARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on CPU_SUBTYPE_SH7785
 	help
 	  Select AP-SH4A-3A if configuring for an ALPHAPROJECT AP-SH4A-3A.
@@ -342,6 +354,7 @@ config SH_APSH4AD0A
 	bool "AP-SH4AD-0A"
 	select SH_ALPHA_BOARD
 	select SYS_SUPPORTS_PCI
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on CPU_SUBTYPE_SH7786
 	help
 	  Select AP-SH4AD-0A if configuring for an ALPHAPROJECT AP-SH4AD-0A.
diff --git a/arch/sh/boards/board-apsh4a3a.c b/arch/sh/boards/board-apsh4a3a.c
index 2823619c600..0a39c241628 100644
--- a/arch/sh/boards/board-apsh4a3a.c
+++ b/arch/sh/boards/board-apsh4a3a.c
@@ -13,6 +13,8 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/mtd/physmap.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/irq.h>
 #include <linux/clk.h>
@@ -66,6 +68,12 @@ static struct platform_device nor_flash_device = {
 	.resource	= nor_flash_resources,
 };
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static struct resource smsc911x_resources[] = {
 	[0] = {
 		.name		= "smsc911x-memory",
@@ -105,6 +113,8 @@ static struct platform_device *apsh4a3a_devices[] __initdata = {
 
 static int __init apsh4a3a_devices_setup(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	return platform_add_devices(apsh4a3a_devices,
 				    ARRAY_SIZE(apsh4a3a_devices));
 }
diff --git a/arch/sh/boards/board-apsh4ad0a.c b/arch/sh/boards/board-apsh4ad0a.c
index b4d6292a924..92eac3a9918 100644
--- a/arch/sh/boards/board-apsh4ad0a.c
+++ b/arch/sh/boards/board-apsh4ad0a.c
@@ -12,12 +12,20 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/irq.h>
 #include <linux/clk.h>
 #include <asm/machvec.h>
 #include <asm/sizes.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static struct resource smsc911x_resources[] = {
 	[0] = {
 		.name		= "smsc911x-memory",
@@ -56,6 +64,8 @@ static struct platform_device *apsh4ad0a_devices[] __initdata = {
 
 static int __init apsh4ad0a_devices_setup(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	return platform_add_devices(apsh4ad0a_devices,
 				    ARRAY_SIZE(apsh4ad0a_devices));
 }
diff --git a/arch/sh/boards/board-magicpanelr2.c b/arch/sh/boards/board-magicpanelr2.c
index 90568f9de3a..20500858b56 100644
--- a/arch/sh/boards/board-magicpanelr2.c
+++ b/arch/sh/boards/board-magicpanelr2.c
@@ -14,6 +14,8 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/gpio.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
@@ -24,6 +26,12 @@
 #include <asm/heartbeat.h>
 #include <cpu/sh7720.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 #define LAN9115_READY	(__raw_readl(0xA8000084UL) & 0x00000001UL)
 
 /* Wait until reset finished. Timeout is 100ms. */
@@ -348,6 +356,8 @@ static struct platform_device *mpr2_devices[] __initdata = {
 
 static int __init mpr2_devices_setup(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	return platform_add_devices(mpr2_devices, ARRAY_SIZE(mpr2_devices));
 }
 device_initcall(mpr2_devices_setup);
diff --git a/arch/sh/boards/board-polaris.c b/arch/sh/boards/board-polaris.c
index 0978ae2e484..37a08d09472 100644
--- a/arch/sh/boards/board-polaris.c
+++ b/arch/sh/boards/board-polaris.c
@@ -9,6 +9,8 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/io.h>
 #include <asm/irq.h>
@@ -22,6 +24,12 @@
 #define AREA5_WAIT_CTRL	(0x1C00)
 #define WAIT_STATES_10	(0x7)
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
 static struct resource smsc911x_resources[] = {
 	[0] = {
 		.name		= "smsc911x-memory",
@@ -88,6 +96,8 @@ static int __init polaris_initialise(void)
 
 	printk(KERN_INFO "Configuring Polaris external bus\n");
 
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	/* Configure area 5 with 2 wait states */
 	wcr = __raw_readw(WCR2);
 	wcr &= (~AREA5_WAIT_CTRL);
diff --git a/arch/sh/boards/board-sh2007.c b/arch/sh/boards/board-sh2007.c
index b90b78f6a82..1980bb7e578 100644
--- a/arch/sh/boards/board-sh2007.c
+++ b/arch/sh/boards/board-sh2007.c
@@ -6,6 +6,8 @@
  */
 #include <linux/init.h>
 #include <linux/irq.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/platform_device.h>
 #include <linux/ata_platform.h>
@@ -13,6 +15,14 @@
 #include <asm/machvec.h>
 #include <mach/sh2007.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+	REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
+};
+
 struct smsc911x_platform_config smc911x_info = {
 	.flags		= SMSC911X_USE_32BIT,
 	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
@@ -98,6 +108,8 @@ static struct platform_device *sh2007_devices[] __initdata = {
 
 static int __init sh2007_io_init(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	platform_add_devices(sh2007_devices, ARRAY_SIZE(sh2007_devices));
 	return 0;
 }
diff --git a/arch/sh/boards/board-sh7757lcr.c b/arch/sh/boards/board-sh7757lcr.c
index 5087f8bb4cf..41f86702eb9 100644
--- a/arch/sh/boards/board-sh7757lcr.c
+++ b/arch/sh/boards/board-sh7757lcr.c
@@ -12,6 +12,8 @@
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
 #include <linux/irq.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
 #include <linux/io.h>
@@ -199,6 +201,15 @@ static struct platform_device sh7757_eth_giga1_device = {
 	},
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0, MMCIF */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
 /* SH_MMCIF */
 static struct resource sh_mmcif_resources[] = {
 	[0] = {
@@ -329,6 +340,9 @@ static struct spi_board_info spi_board_info[] = {
 
 static int __init sh7757lcr_devices_setup(void)
 {
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
 	/* RGMII (PTA) */
 	gpio_request(GPIO_FN_ET0_MDC, NULL);
 	gpio_request(GPIO_FN_ET0_MDIO, NULL);
diff --git a/arch/sh/boards/mach-ap325rxa/setup.c b/arch/sh/boards/mach-ap325rxa/setup.c
index f33ebf44707..9e963c1d144 100644
--- a/arch/sh/boards/mach-ap325rxa/setup.c
+++ b/arch/sh/boards/mach-ap325rxa/setup.c
@@ -20,6 +20,8 @@
 #include <linux/mtd/sh_flctl.h>
 #include <linux/delay.h>
 #include <linux/i2c.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/gpio.h>
 #include <linux/videodev2.h>
@@ -34,6 +36,12 @@
 #include <asm/suspend.h>
 #include <cpu/sh7723.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static struct smsc911x_platform_config smsc911x_config = {
 	.phy_interface	= PHY_INTERFACE_MODE_MII,
 	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
@@ -423,6 +431,15 @@ static struct platform_device ceu_device = {
 	},
 };
 
+/* Fixed 3.3V regulators to be used by SDHI0, SDHI1 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
 static struct resource sdhi0_cn3_resources[] = {
 	[0] = {
 		.name	= "SDHI0",
@@ -544,6 +561,10 @@ static int __init ap325rxa_devices_setup(void)
 					&ap325rxa_sdram_leave_start,
 					&ap325rxa_sdram_leave_end);
 
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	/* LD3 and LD4 LEDs */
 	gpio_request(GPIO_PTX5, NULL); /* RUN */
 	gpio_direction_output(GPIO_PTX5, 1);
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index 4158d70c0de..64559e8af14 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -19,6 +19,8 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/delay.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/usb/r8a66597.h>
 #include <linux/usb/renesas_usbhs.h>
 #include <linux/i2c.h>
@@ -242,9 +244,17 @@ static int usbhs_get_id(struct platform_device *pdev)
 	return gpio_get_value(GPIO_PTB3);
 }
 
+static void usbhs_phy_reset(struct platform_device *pdev)
+{
+	/* enable vbus if HOST */
+	if (!gpio_get_value(GPIO_PTB3))
+		gpio_set_value(GPIO_PTB5, 1);
+}
+
 static struct renesas_usbhs_platform_info usbhs_info = {
 	.platform_callback = {
 		.get_id		= usbhs_get_id,
+		.phy_reset	= usbhs_phy_reset,
 	},
 	.driver_param = {
 		.buswait_bwait		= 4,
@@ -518,10 +528,86 @@ static struct i2c_board_info ts_i2c_clients = {
 	.irq		= IRQ0,
 };
 
+static struct regulator_consumer_supply cn12_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
+static struct regulator_init_data cn12_power_init_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(cn12_power_consumers),
+	.consumer_supplies      = cn12_power_consumers,
+};
+
+static struct fixed_voltage_config cn12_power_info = {
+	.supply_name = "CN12 SD/MMC Vdd",
+	.microvolts = 3300000,
+	.gpio = GPIO_PTB7,
+	.enable_high = 1,
+	.init_data = &cn12_power_init_data,
+};
+
+static struct platform_device cn12_power = {
+	.name = "reg-fixed-voltage",
+	.id   = 0,
+	.dev  = {
+		.platform_data = &cn12_power_info,
+	},
+};
+
 #if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
 /* SDHI0 */
+static struct regulator_consumer_supply sdhi0_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_init_data sdhi0_power_init_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(sdhi0_power_consumers),
+	.consumer_supplies      = sdhi0_power_consumers,
+};
+
+static struct fixed_voltage_config sdhi0_power_info = {
+	.supply_name = "CN11 SD/MMC Vdd",
+	.microvolts = 3300000,
+	.gpio = GPIO_PTB6,
+	.enable_high = 1,
+	.init_data = &sdhi0_power_init_data,
+};
+
+static struct platform_device sdhi0_power = {
+	.name = "reg-fixed-voltage",
+	.id   = 1,
+	.dev  = {
+		.platform_data = &sdhi0_power_info,
+	},
+};
+
 static void sdhi0_set_pwr(struct platform_device *pdev, int state)
 {
+	static int power_gpio = -EINVAL;
+
+	if (power_gpio < 0) {
+		int ret = gpio_request(GPIO_PTB6, NULL);
+		if (!ret) {
+			power_gpio = GPIO_PTB6;
+			gpio_direction_output(power_gpio, 0);
+		}
+	}
+
+	/*
+	 * Toggle the GPIO regardless, whether we managed to grab it above or
+	 * the fixed regulator driver did.
+	 */
 	gpio_set_value(GPIO_PTB6, state);
 }
 
@@ -562,13 +648,27 @@ static struct platform_device sdhi0_device = {
 	},
 };
 
-#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
-/* SDHI1 */
-static void sdhi1_set_pwr(struct platform_device *pdev, int state)
+static void cn12_set_pwr(struct platform_device *pdev, int state)
 {
+	static int power_gpio = -EINVAL;
+
+	if (power_gpio < 0) {
+		int ret = gpio_request(GPIO_PTB7, NULL);
+		if (!ret) {
+			power_gpio = GPIO_PTB7;
+			gpio_direction_output(power_gpio, 0);
+		}
+	}
+
+	/*
+	 * Toggle the GPIO regardless, whether we managed to grab it above or
+	 * the fixed regulator driver did.
+	 */
 	gpio_set_value(GPIO_PTB7, state);
 }
 
+#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
+/* SDHI1 */
 static int sdhi1_get_cd(struct platform_device *pdev)
 {
 	return !gpio_get_value(GPIO_PTW7);
@@ -579,7 +679,7 @@ static struct sh_mobile_sdhi_info sdhi1_info = {
 	.dma_slave_rx	= SHDMA_SLAVE_SDHI1_RX,
 	.tmio_caps      = MMC_CAP_SDIO_IRQ | MMC_CAP_POWER_OFF_CARD |
 			  MMC_CAP_NEEDS_POLL,
-	.set_pwr	= sdhi1_set_pwr,
+	.set_pwr	= cn12_set_pwr,
 	.get_cd		= sdhi1_get_cd,
 };
 
@@ -899,14 +999,9 @@ static struct platform_device vou_device = {
 
 #if defined(CONFIG_MMC_SH_MMCIF) || defined(CONFIG_MMC_SH_MMCIF_MODULE)
 /* SH_MMCIF */
-static void mmcif_set_pwr(struct platform_device *pdev, int state)
-{
-	gpio_set_value(GPIO_PTB7, state);
-}
-
 static void mmcif_down_pwr(struct platform_device *pdev)
 {
-	gpio_set_value(GPIO_PTB7, 0);
+	cn12_set_pwr(pdev, 0);
 }
 
 static struct resource sh_mmcif_resources[] = {
@@ -929,7 +1024,7 @@ static struct resource sh_mmcif_resources[] = {
 };
 
 static struct sh_mmcif_plat_data sh_mmcif_plat = {
-	.set_pwr	= mmcif_set_pwr,
+	.set_pwr	= cn12_set_pwr,
 	.down_pwr	= mmcif_down_pwr,
 	.sup_pclk	= 0, /* SH7724: Max Pclk/2 */
 	.caps		= MMC_CAP_4_BIT_DATA |
@@ -960,7 +1055,9 @@ static struct platform_device *ecovec_devices[] __initdata = {
 	&ceu0_device,
 	&ceu1_device,
 	&keysc_device,
+	&cn12_power,
 #if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
+	&sdhi0_power,
 	&sdhi0_device,
 #if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
 	&sdhi1_device,
@@ -1258,8 +1355,6 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_SDHI0D2,  NULL);
 	gpio_request(GPIO_FN_SDHI0D1,  NULL);
 	gpio_request(GPIO_FN_SDHI0D0,  NULL);
-	gpio_request(GPIO_PTB6, NULL);
-	gpio_direction_output(GPIO_PTB6, 0);
 #else
 	/* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */
 	gpio_request(GPIO_FN_MSIOF0_TXD, NULL);
@@ -1288,8 +1383,6 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_MMC_D0, NULL);
 	gpio_request(GPIO_FN_MMC_CLK, NULL);
 	gpio_request(GPIO_FN_MMC_CMD, NULL);
-	gpio_request(GPIO_PTB7, NULL);
-	gpio_direction_output(GPIO_PTB7, 0);
 
 	cn12_enabled = true;
 #elif defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
@@ -1301,8 +1394,6 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_SDHI1D2,  NULL);
 	gpio_request(GPIO_FN_SDHI1D1,  NULL);
 	gpio_request(GPIO_FN_SDHI1D0,  NULL);
-	gpio_request(GPIO_PTB7, NULL);
-	gpio_direction_output(GPIO_PTB7, 0);
 
 	/* Card-detect, used on CN12 with SDHI1 */
 	gpio_request(GPIO_PTW7, NULL);
diff --git a/arch/sh/boards/mach-kfr2r09/setup.c b/arch/sh/boards/mach-kfr2r09/setup.c
index 43a179ce9af..f2a4304fbe2 100644
--- a/arch/sh/boards/mach-kfr2r09/setup.c
+++ b/arch/sh/boards/mach-kfr2r09/setup.c
@@ -21,6 +21,8 @@
 #include <linux/input.h>
 #include <linux/input/sh_keysc.h>
 #include <linux/i2c.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/usb/r8a66597.h>
 #include <linux/videodev2.h>
 #include <linux/sh_intc.h>
@@ -341,6 +343,13 @@ static struct platform_device kfr2r09_camera = {
 	},
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
 static struct resource kfr2r09_sh_sdhi0_resources[] = {
 	[0] = {
 		.name	= "SDHI0",
@@ -523,6 +532,9 @@ static int __init kfr2r09_devices_setup(void)
 					&kfr2r09_sdram_leave_start,
 					&kfr2r09_sdram_leave_end);
 
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
 	/* enable SCIF1 serial port for YC401 console support */
 	gpio_request(GPIO_FN_SCIF1_RXD, NULL);
 	gpio_request(GPIO_FN_SCIF1_TXD, NULL);
diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c
index a8a1ca741c8..8b73194ed2c 100644
--- a/arch/sh/boards/mach-migor/setup.c
+++ b/arch/sh/boards/mach-migor/setup.c
@@ -17,6 +17,8 @@
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/nand.h>
 #include <linux/i2c.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smc91x.h>
 #include <linux/delay.h>
 #include <linux/clk.h>
@@ -386,6 +388,13 @@ static struct platform_device migor_ceu_device = {
 	},
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
 static struct resource sdhi_cn9_resources[] = {
 	[0] = {
 		.name	= "SDHI",
@@ -498,6 +507,10 @@ static int __init migor_devices_setup(void)
 					&migor_sdram_enter_end,
 					&migor_sdram_leave_start,
 					&migor_sdram_leave_end);
+
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
 	/* Let D11 LED show STATUS0 */
 	gpio_request(GPIO_FN_STATUS0, NULL);
 
diff --git a/arch/sh/boards/mach-rsk/setup.c b/arch/sh/boards/mach-rsk/setup.c
index 895f030070d..2685ea03b06 100644
--- a/arch/sh/boards/mach-rsk/setup.c
+++ b/arch/sh/boards/mach-rsk/setup.c
@@ -16,9 +16,17 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/map.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <asm/machvec.h>
 #include <asm/io.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static const char *part_probes[] = { "cmdlinepart", NULL };
 
 static struct mtd_partition rsk_partitions[] = {
@@ -67,6 +75,8 @@ static struct platform_device *rsk_devices[] __initdata = {
 
 static int __init rsk_devices_setup(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	return platform_add_devices(rsk_devices,
 				    ARRAY_SIZE(rsk_devices));
 }
diff --git a/arch/sh/boards/mach-sdk7786/setup.c b/arch/sh/boards/mach-sdk7786/setup.c
index 27a2314f50a..c29268bfd34 100644
--- a/arch/sh/boards/mach-sdk7786/setup.c
+++ b/arch/sh/boards/mach-sdk7786/setup.c
@@ -11,6 +11,8 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/i2c.h>
 #include <linux/irq.h>
@@ -38,6 +40,12 @@ static struct platform_device heartbeat_device = {
 	.resource	= &heartbeat_resource,
 };
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static struct resource smsc911x_resources[] = {
 	[0] = {
 		.name		= "smsc911x-memory",
@@ -236,6 +244,8 @@ static void __init sdk7786_setup(char **cmdline_p)
 {
 	pr_info("Renesas Technology Europe SDK7786 support:\n");
 
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	sdk7786_fpga_init();
 	sdk7786_nmi_init();
 
diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c
index ffbf5bc7366..35f6efa3ac0 100644
--- a/arch/sh/boards/mach-se/7724/setup.c
+++ b/arch/sh/boards/mach-se/7724/setup.c
@@ -18,6 +18,8 @@
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/mtd/physmap.h>
 #include <linux/delay.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smc91x.h>
 #include <linux/gpio.h>
 #include <linux/input.h>
@@ -454,6 +456,15 @@ static struct platform_device sh7724_usb1_gadget_device = {
 	.resource	= sh7724_usb1_gadget_resources,
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0, SDHI1 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
 static struct resource sdhi0_cn7_resources[] = {
 	[0] = {
 		.name	= "SDHI0",
@@ -684,6 +695,10 @@ static int __init devices_setup(void)
 					&ms7724se_sdram_enter_end,
 					&ms7724se_sdram_leave_start,
 					&ms7724se_sdram_leave_end);
+
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
 	/* Reset Release */
 	fpga_out = __raw_readw(FPGA_OUT);
 	/* bit4: NTSC_PDN, bit5: NTSC_RESET */
diff --git a/arch/sh/include/cpu-sh4/cpu/sh7757.h b/arch/sh/include/cpu-sh4/cpu/sh7757.h
index 41f9f8b9db7..5340f3bc186 100644
--- a/arch/sh/include/cpu-sh4/cpu/sh7757.h
+++ b/arch/sh/include/cpu-sh4/cpu/sh7757.h
@@ -283,5 +283,7 @@ enum {
 	SHDMA_SLAVE_RIIC8_RX,
 	SHDMA_SLAVE_RIIC9_TX,
 	SHDMA_SLAVE_RIIC9_RX,
+	SHDMA_SLAVE_RSPI_TX,
+	SHDMA_SLAVE_RSPI_RX,
 };
 #endif /* __ASM_SH7757_H__ */
diff --git a/arch/sh/kernel/cpu/sh4a/clock-sh7724.c b/arch/sh/kernel/cpu/sh4a/clock-sh7724.c
index c87e78f7323..5f30f805d2f 100644
--- a/arch/sh/kernel/cpu/sh4a/clock-sh7724.c
+++ b/arch/sh/kernel/cpu/sh4a/clock-sh7724.c
@@ -334,8 +334,8 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_CON_ID("tpu0", &mstp_clks[HWBLK_TPU]),
 	CLKDEV_CON_ID("irda0", &mstp_clks[HWBLK_IRDA]),
 	CLKDEV_CON_ID("tsif0", &mstp_clks[HWBLK_TSIF]),
-	CLKDEV_CON_ID("usb1", &mstp_clks[HWBLK_USB1]),
-	CLKDEV_CON_ID("usb0", &mstp_clks[HWBLK_USB0]),
+	CLKDEV_DEV_ID("renesas_usbhs.1", &mstp_clks[HWBLK_USB1]),
+	CLKDEV_DEV_ID("renesas_usbhs.0", &mstp_clks[HWBLK_USB0]),
 	CLKDEV_CON_ID("2dg0", &mstp_clks[HWBLK_2DG]),
 	CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[HWBLK_SDHI0]),
 	CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[HWBLK_SDHI1]),
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
index 65786c7f5de..6a868b091c2 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
@@ -12,6 +12,7 @@
 #include <linux/platform_device.h>
 #include <linux/serial.h>
 #include <linux/serial_sci.h>
+#include <linux/sh_dma.h>
 #include <linux/sh_timer.h>
 #include <linux/sh_intc.h>
 #include <linux/uio_driver.h>
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7757.c b/arch/sh/kernel/cpu/sh4a/setup-sh7757.c
index a7708425afa..4a2f357f4df 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7757.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7757.c
@@ -216,6 +216,20 @@ static const struct sh_dmae_slave_config sh7757_dmae1_slaves[] = {
 				  TS_INDEX2VAL(XMIT_SZ_8BIT),
 		.mid_rid	= 0x42,
 	},
+	{
+		.slave_id	= SHDMA_SLAVE_RSPI_TX,
+		.addr		= 0xfe480004,
+		.chcr		= SM_INC | 0x800 | 0x40000000 |
+				  TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc1,
+	},
+	{
+		.slave_id	= SHDMA_SLAVE_RSPI_RX,
+		.addr		= 0xfe480004,
+		.chcr		= DM_INC | 0x800 | 0x40000000 |
+				  TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc2,
+	},
 };
 
 static const struct sh_dmae_slave_config sh7757_dmae2_slaves[] = {
diff --git a/arch/sh/mm/fault.c b/arch/sh/mm/fault.c
index 1fc25d85e51..3bdc1ad9a34 100644
--- a/arch/sh/mm/fault.c
+++ b/arch/sh/mm/fault.c
@@ -58,11 +58,15 @@ static void show_pte(struct mm_struct *mm, unsigned long addr)
 {
 	pgd_t *pgd;
 
-	if (mm)
+	if (mm) {
 		pgd = mm->pgd;
-	else
+	} else {
 		pgd = get_TTB();
 
+		if (unlikely(!pgd))
+			pgd = swapper_pg_dir;
+	}
+
 	printk(KERN_ALERT "pgd = %p\n", pgd);
 	pgd += pgd_index(addr);
 	printk(KERN_ALERT "[%08lx] *pgd=%0*Lx", addr,