Merge branch 'at91/soc' into next/soc

The soc2 branch is based on this cleanup:

* at91/soc:
  ARM: at91: Remove the support for the RSI EWS board
  ARM: at91: remove board file for Acme Systems Fox G20

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

4 files changed, 0 insertions, 518 deletions

diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index 44ace320d2e..aa31e556e2e 100644
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -132,12 +132,6 @@ config MACH_ECO920
 	bool "eco920"
 	help
 	  Select this if you are using the eco920 board
-
-config MACH_RSI_EWS
-	bool "RSI Embedded Webserver"
-	depends on ARCH_AT91RM9200
-	help
-	  Select this if you are using RSIs EWS board.
 endif
 
 # ----------------------------------------------------------
@@ -212,12 +206,6 @@ config MACH_CPU9G20
 	  Select this if you are using a Eukrea Electromatique's
 	  CPU9G20 Board <http://www.eukrea.com/>
 
-config MACH_ACMENETUSFOXG20
-	bool "Acme Systems srl FOX Board G20"
-	help
-	  Select this if you are using Acme Systems
-	  FOX Board G20 <http://www.acmesystems.it>
-
 config MACH_PORTUXG20
 	bool "taskit PortuxG20"
 	help
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 78e9cec282f..c677f9688ff 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91)	+= board-ecbat91.o
 obj-$(CONFIG_MACH_YL9200)	+= board-yl-9200.o
 obj-$(CONFIG_MACH_CPUAT91)	+= board-cpuat91.o
 obj-$(CONFIG_MACH_ECO920)	+= board-eco920.o
-obj-$(CONFIG_MACH_RSI_EWS)	+= board-rsi-ews.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
@@ -69,7 +68,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
 # AT91SAM9G20 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
 obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
-obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o
 obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
deleted file mode 100644
index 8b22c60bb23..00000000000
--- a/arch/arm/mach-at91/board-foxg20.c
+++ /dev/null
@@ -1,272 +0,0 @@
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2008 Atmel
- *  Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
- *  Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-#include <linux/w1-gpio.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-/*
- * The FOX Board G20 hardware comes as the "Netus G20" board with
- * just the cpu, ram, dataflash and two header connectors.
- * This is plugged into the FOX Board which provides the ethernet,
- * usb, rtc, leds, switch, ...
- *
- * For more info visit: http://www.acmesystems.it/foxg20
- */
-
-
-static void __init foxg20_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata foxg20_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata foxg20_udc_data = {
-	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info foxg20_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata foxg20_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
-};
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata foxg20_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led foxg20_leds[] = {
-	{	/* user led, red */
-		.name			= "user_led",
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 0,
-		.default_trigger	= "heartbeat",
-	},
-};
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button foxg20_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PC4,
-		.code		= BTN_1,
-		.desc		= "Button 1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-};
-
-static struct gpio_keys_platform_data foxg20_button_data = {
-	.buttons	= foxg20_buttons,
-	.nbuttons	= ARRAY_SIZE(foxg20_buttons),
-};
-
-static struct platform_device foxg20_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &foxg20_button_data,
-	}
-};
-
-static void __init foxg20_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PC4, 1);	/* btn1 */
-	at91_set_deglitch(AT91_PIN_PC4, 1);
-
-	platform_device_register(&foxg20_button_device);
-}
-#else
-static void __init foxg20_add_device_buttons(void) {}
-#endif
-
-
-#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
-	.pin		= AT91_PIN_PB16,
-	.is_open_drain  = 1,
-	.ext_pullup_enable_pin	= -EINVAL,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-static void __init at91_add_device_w1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-#endif
-
-
-static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-	},
-};
-
-
-static void __init foxg20_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-				ATMEL_UART_CTS
-				| ATMEL_UART_RTS
-				| ATMEL_UART_DTR
-				| ATMEL_UART_DSR
-				| ATMEL_UART_DCD
-				| ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US3, 4,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* Set the internal pull-up resistor on DRXD */
-	at91_set_A_periph(AT91_PIN_PB14, 1);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&foxg20_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&foxg20_udc_data);
-	/* SPI */
-	at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
-	/* Ethernet */
-	at91_add_device_eth(&foxg20_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &foxg20_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
-	/* LEDs */
-	at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
-	/* Push Buttons */
-	foxg20_add_device_buttons();
-#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-	at91_add_device_w1();
-#endif
-}
-
-MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20")
-	/* Maintainer: Sergio Tanzilli */
-	.init_time	= at91sam926x_pit_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= foxg20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= foxg20_board_init,
-MACHINE_END
diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
deleted file mode 100644
index f28e8b74df4..00000000000
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ /dev/null
@@ -1,232 +0,0 @@
-/*
- * board-rsi-ews.c
- *
- *  Copyright (C)
- *  2005 SAN People,
- *  2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
- *
- * Licensed under GPLv2 or later.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include <linux/gpio.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init rsi_ews_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * Ethernet
- */
-static struct macb_platform_data rsi_ews_eth_data __initdata = {
-	.phy_irq_pin	= AT91_PIN_PC4,
-	.is_rmii	= 1,
-};
-
-/*
- * USB Host
- */
-static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
-	.ports		= 1,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * SD/MC
- */
-static struct mci_platform_data __initdata rsi_ews_mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PB27,
-		.wp_pin		= AT91_PIN_PB29,
-	},
-};
-
-/*
- * I2C
- */
-static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
-	{
-		I2C_BOARD_INFO("ds1337", 0x68),
-	},
-	{
-		I2C_BOARD_INFO("24c01", 0x50),
-	}
-};
-
-/*
- * LEDs
- */
-static struct gpio_led rsi_ews_leds[] = {
-	{
-		.name			= "led0",
-		.gpio			= AT91_PIN_PB6,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led1",
-		.gpio			= AT91_PIN_PB7,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led2",
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 0,
-	},
-	{
-		.name			= "led3",
-		.gpio			= AT91_PIN_PB9,
-		.active_low		= 0,
-	},
-};
-
-/*
- * DataFlash
- */
-static struct spi_board_info rsi_ews_spi_devices[] = {
-	{	/* DataFlash chip 1*/
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 5 * 1000 * 1000,
-	},
-	{	/* DataFlash chip 2*/
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 5 * 1000 * 1000,
-	},
-};
-
-/*
- * NOR flash
- */
-static struct mtd_partition rsiews_nor_partitions[] = {
-	{
-		.name		= "boot",
-		.offset		= 0,
-		.size		= 3 * SZ_128K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= SZ_2M - (3 * SZ_128K)
-	},
-	{
-		.name		= "root",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= SZ_8M
-	},
-	{
-		.name		= "kernelupd",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= 3 * SZ_512K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-	{
-		.name		= "rootupd",
-		.offset		= MTDPART_OFS_NXTBLK,
-		.size		= 9 * SZ_512K,
-		.mask_flags	= MTD_WRITEABLE
-	},
-};
-
-static struct physmap_flash_data rsiews_nor_data = {
-	.width		= 2,
-	.parts		= rsiews_nor_partitions,
-	.nr_parts	= ARRAY_SIZE(rsiews_nor_partitions),
-};
-
-#define NOR_BASE	AT91_CHIPSELECT_0
-#define NOR_SIZE	SZ_16M
-
-static struct resource nor_flash_resources[] = {
-	{
-		.start	= NOR_BASE,
-		.end	= NOR_BASE + NOR_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device rsiews_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-				.platform_data	= &rsiews_nor_data,
-	},
-	.resource	= nor_flash_resources,
-	.num_resources	= ARRAY_SIZE(nor_flash_resources),
-};
-
-/*
- * Init Func
- */
-static void __init rsi_ews_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	/* This one is for debugging */
-	at91_register_uart(0, 0, 0);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	/* Dialin/-out modem interface */
-	at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS) */
-	/* RS485 communication */
-	at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-	at91_add_device_serial();
-	at91_set_gpio_output(AT91_PIN_PA21, 0);
-	/* Ethernet */
-	at91_add_device_eth(&rsi_ews_eth_data);
-	/* USB Host */
-	at91_add_device_usbh(&rsi_ews_usbh_data);
-	/* I2C */
-	at91_add_device_i2c(rsi_ews_i2c_devices,
-			ARRAY_SIZE(rsi_ews_i2c_devices));
-	/* SPI */
-	at91_add_device_spi(rsi_ews_spi_devices,
-			ARRAY_SIZE(rsi_ews_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &rsi_ews_mci0_data);
-	/* NOR Flash */
-	platform_device_register(&rsiews_nor_flash);
-	/* LEDs */
-	at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
-}
-
-MACHINE_START(RSI_EWS, "RSI EWS")
-	/* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */
-	.init_time	= at91rm9200_timer_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= rsi_ews_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= rsi_ews_board_init,
-MACHINE_END