Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: don't set IORDY for reset
  sata_fsl: Add power mgmt support
  [libata] PATA driver for CF interface on AT91SAM9260 SoC
  [libata] beautify module parameters

1 files changed, 15 insertions, 10 deletions

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index ca4d208ddf3..045a486a09e 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -125,19 +125,19 @@ MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link spe
 
 static int atapi_enabled = 1;
 module_param(atapi_enabled, int, 0444);
-MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on [default])");
 
 static int atapi_dmadir = 0;
 module_param(atapi_dmadir, int, 0444);
-MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_dmadir, "Enable ATAPI DMADIR bridge support (0=off [default], 1=on)");
 
 int atapi_passthru16 = 1;
 module_param(atapi_passthru16, int, 0444);
-MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices; on by default (0=off, 1=on)");
+MODULE_PARM_DESC(atapi_passthru16, "Enable ATA_16 passthru for ATAPI devices (0=off, 1=on [default])");
 
 int libata_fua = 0;
 module_param_named(fua, libata_fua, int, 0444);
-MODULE_PARM_DESC(fua, "FUA support (0=off, 1=on)");
+MODULE_PARM_DESC(fua, "FUA support (0=off [default], 1=on)");
 
 static int ata_ignore_hpa;
 module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644);
@@ -153,11 +153,11 @@ MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)");
 
 int libata_noacpi = 0;
 module_param_named(noacpi, libata_noacpi, int, 0444);
-MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set");
+MODULE_PARM_DESC(noacpi, "Disable the use of ACPI in probe/suspend/resume (0=off [default], 1=on)");
 
 int libata_allow_tpm = 0;
 module_param_named(allow_tpm, libata_allow_tpm, int, 0444);
-MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands");
+MODULE_PARM_DESC(allow_tpm, "Permit the use of TPM commands (0=off [default], 1=on)");
 
 MODULE_AUTHOR("Jeff Garzik");
 MODULE_DESCRIPTION("Library module for ATA devices");
@@ -1993,11 +1993,17 @@ unsigned int ata_do_simple_cmd(struct ata_device *dev, u8 cmd)
  *	Check if the current speed of the device requires IORDY. Used
  *	by various controllers for chip configuration.
  */
-
 unsigned int ata_pio_need_iordy(const struct ata_device *adev)
 {
-	/* Controller doesn't support  IORDY. Probably a pointless check
-	   as the caller should know this */
+	/* Don't set IORDY if we're preparing for reset.  IORDY may
+	 * lead to controller lock up on certain controllers if the
+	 * port is not occupied.  See bko#11703 for details.
+	 */
+	if (adev->link->ap->pflags & ATA_PFLAG_RESETTING)
+		return 0;
+	/* Controller doesn't support IORDY.  Probably a pointless
+	 * check as the caller should know this.
+	 */
 	if (adev->link->ap->flags & ATA_FLAG_NO_IORDY)
 		return 0;
 	/* CF spec. r4.1 Table 22 says no iordy on PIO5 and PIO6.  */
@@ -2020,7 +2026,6 @@ unsigned int ata_pio_need_iordy(const struct ata_device *adev)
  *	Compute the highest mode possible if we are not using iordy. Return
  *	-1 if no iordy mode is available.
  */
-
 static u32 ata_pio_mask_no_iordy(const struct ata_device *adev)
 {
 	/* If we have no drive specific rule, then PIO 2 is non IORDY */