Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into merge

Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ath/ath5k/phy.c
	drivers/net/wireless/iwlwifi/iwl-4965.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
	drivers/net/wireless/iwlwifi/iwl-core.c
	drivers/net/wireless/iwlwifi/iwl-core.h
	drivers/net/wireless/iwlwifi/iwl-tx.c

1 files changed, 85 insertions, 104 deletions

diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
index 4224cfccede..8839307a64c 100644
--- a/drivers/ata/pata_hpt37x.c
+++ b/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt37x"
-#define DRV_VERSION	"0.6.14"
+#define DRV_VERSION	"0.6.15"
 
 struct hpt_clock {
 	u8	xfer_speed;
@@ -39,25 +39,24 @@ struct hpt_chip {
 
 /* key for bus clock timings
  * bit
- * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- *        DMA. cycles = value + 1
- * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- *        DMA. cycles = value + 1
- * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ * 0:3    data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 4:8    data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 9:12   cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
  *        register access.
- * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ * 13:17  cmd_low_time. Active time of DIOW_/DIOR_ during task file
  *        register access.
- * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- *        during task file register access.
- * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- *        xfer.
- * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ * 18:20  udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21     CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24  pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27  cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
  *        register access.
- * 28     UDMA enable
- * 29     DMA enable
- * 30     PIO_MST enable. if set, the chip is in bus master mode during
- *        PIO.
- * 31     FIFO enable.
+ * 28     UDMA enable.
+ * 29     DMA  enable.
+ * 30     PIO_MST enable. If set, the chip is in bus master mode during
+ *        PIO xfer.
+ * 31     FIFO enable. Only for PIO.
  */
 
 static struct hpt_clock hpt37x_timings_33[] = {
@@ -384,20 +383,12 @@ static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
 	return ata_sff_prereset(link, deadline);
 }
 
-/**
- *	hpt370_set_piomode		-	PIO setup
- *	@ap: ATA interface
- *	@adev: device on the interface
- *
- *	Perform PIO mode setup.
- */
-
-static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+			    u8 mode)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	u32 addr1, addr2;
-	u32 reg;
-	u32 mode;
+	u32 reg, timing, mask;
 	u8 fast;
 
 	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -409,11 +400,31 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	fast |= 0x01;
 	pci_write_config_byte(pdev, addr2, fast);
 
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt37x_find_mode(ap, mode);
+
 	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt37x_find_mode(ap, adev->pio_mode);
-	mode &= 0xCFC3FFFF;	/* Leave DMA bits alone */
-	reg &= ~0xCFC3FFFF;	/* Strip timing bits */
-	pci_write_config_dword(pdev, addr1, reg | mode);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ *	hpt370_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt370_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -421,33 +432,12 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *	@ap: ATA interface
  *	@adev: Device being configured
  *
- *	Set up the channel for MWDMA or UDMA modes. Much the same as with
- *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ *	Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-	u32 addr1, addr2;
-	u32 reg, mode, mask;
-	u8 fast;
-
-	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-	addr2 = 0x51 + 4 * ap->port_no;
-
-	/* Fast interrupt prediction disable, hold off interrupt disable */
-	pci_read_config_byte(pdev, addr2, &fast);
-	fast &= ~0x02;
-	fast |= 0x01;
-	pci_write_config_byte(pdev, addr2, fast);
-
-	mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt37x_find_mode(ap, adev->dma_mode);
-	mode &= mask;
-	reg &= ~mask;
-	pci_write_config_dword(pdev, addr1, reg | mode);
+	hpt370_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**
@@ -461,24 +451,25 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
 {
 	struct ata_port *ap = qc->ap;
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-	u8 dma_stat = ioread8(ap->ioaddr.bmdma_addr + 2);
-	u8 dma_cmd;
 	void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+	u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+	u8 dma_cmd;
 
-	if (dma_stat & 0x01) {
+	if (dma_stat & ATA_DMA_ACTIVE) {
 		udelay(20);
-		dma_stat = ioread8(bmdma + 2);
+		dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
 	}
-	if (dma_stat & 0x01) {
+	if (dma_stat & ATA_DMA_ACTIVE) {
 		/* Clear the engine */
 		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
 		udelay(10);
 		/* Stop DMA */
-		dma_cmd = ioread8(bmdma );
-		iowrite8(dma_cmd & 0xFE, bmdma);
+		dma_cmd = ioread8(bmdma + ATA_DMA_CMD);
+		iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD);
 		/* Clear Error */
-		dma_stat = ioread8(bmdma + 2);
-		iowrite8(dma_stat | 0x06 , bmdma + 2);
+		dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+		iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR,
+			 bmdma + ATA_DMA_STATUS);
 		/* Clear the engine */
 		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
 		udelay(10);
@@ -486,20 +477,12 @@ static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
 	ata_bmdma_stop(qc);
 }
 
-/**
- *	hpt372_set_piomode		-	PIO setup
- *	@ap: ATA interface
- *	@adev: device on the interface
- *
- *	Perform PIO mode setup.
- */
-
-static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+			    u8 mode)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	u32 addr1, addr2;
-	u32 reg;
-	u32 mode;
+	u32 reg, timing, mask;
 	u8 fast;
 
 	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -510,13 +493,32 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	fast &= ~0x07;
 	pci_write_config_byte(pdev, addr2, fast);
 
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt37x_find_mode(ap, mode);
+
 	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt37x_find_mode(ap, adev->pio_mode);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ *	hpt372_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
 
-	printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
-	mode &= 0xCFC3FFFF;	/* Leave DMA bits alone */
-	reg &= ~0xCFC3FFFF;	/* Strip timing bits */
-	pci_write_config_dword(pdev, addr1, reg | mode);
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt372_set_mode(ap, adev, adev->pio_mode);
 }
 
 /**
@@ -524,33 +526,12 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
  *	@ap: ATA interface
  *	@adev: Device being configured
  *
- *	Set up the channel for MWDMA or UDMA modes. Much the same as with
- *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ *	Set up the channel for MWDMA or UDMA modes.
  */
 
 static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
-	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-	u32 addr1, addr2;
-	u32 reg, mode, mask;
-	u8 fast;
-
-	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
-	addr2 = 0x51 + 4 * ap->port_no;
-
-	/* Fast interrupt prediction disable, hold off interrupt disable */
-	pci_read_config_byte(pdev, addr2, &fast);
-	fast &= ~0x07;
-	pci_write_config_byte(pdev, addr2, fast);
-
-	mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
-	pci_read_config_dword(pdev, addr1, &reg);
-	mode = hpt37x_find_mode(ap, adev->dma_mode);
-	printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
-	mode &= mask;
-	reg &= ~mask;
-	pci_write_config_dword(pdev, addr1, reg | mode);
+	hpt372_set_mode(ap, adev, adev->dma_mode);
 }
 
 /**
@@ -1006,7 +987,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 	}
 
 	/* Now kick off ATA set up */
-	return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data);
+	return ata_pci_sff_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
 }
 
 static const struct pci_device_id hpt37x[] = {