[CPUFREQ] Move x86 drivers to drivers/cpufreq/

Signed-off-by: Dave Jones <davej@redhat.com>

1 files changed, 514 insertions, 0 deletions

diff --git a/drivers/cpufreq/gx-suspmod.c b/drivers/cpufreq/gx-suspmod.c
new file mode 100644
index 00000000000..ffe1f2c92ed
--- /dev/null
+++ b/drivers/cpufreq/gx-suspmod.c
@@ -0,0 +1,514 @@
+/*
+ *	Cyrix MediaGX and NatSemi Geode Suspend Modulation
+ *	(C) 2002 Zwane Mwaikambo <zwane@commfireservices.com>
+ *	(C) 2002 Hiroshi Miura   <miura@da-cha.org>
+ *	All Rights Reserved
+ *
+ *	This program is free software; you can redistribute it and/or
+ *      modify it under the terms of the GNU General Public License
+ *      version 2 as published by the Free Software Foundation
+ *
+ *      The author(s) of this software shall not be held liable for damages
+ *      of any nature resulting due to the use of this software. This
+ *      software is provided AS-IS with no warranties.
+ *
+ * Theoretical note:
+ *
+ *	(see Geode(tm) CS5530 manual (rev.4.1) page.56)
+ *
+ *	CPU frequency control on NatSemi Geode GX1/GXLV processor and CS55x0
+ *	are based on Suspend Modulation.
+ *
+ *	Suspend Modulation works by asserting and de-asserting the SUSP# pin
+ *	to CPU(GX1/GXLV) for configurable durations. When asserting SUSP#
+ *	the CPU enters an idle state. GX1 stops its core clock when SUSP# is
+ *	asserted then power consumption is reduced.
+ *
+ *	Suspend Modulation's OFF/ON duration are configurable
+ *	with 'Suspend Modulation OFF Count Register'
+ *	and 'Suspend Modulation ON Count Register'.
+ *	These registers are 8bit counters that represent the number of
+ *	32us intervals which the SUSP# pin is asserted(ON)/de-asserted(OFF)
+ *	to the processor.
+ *
+ *	These counters define a ratio which is the effective frequency
+ *	of operation of the system.
+ *
+ *			       OFF Count
+ *	F_eff = Fgx * ----------------------
+ *	                OFF Count + ON Count
+ *
+ *	0 <= On Count, Off Count <= 255
+ *
+ *	From these limits, we can get register values
+ *
+ *	off_duration + on_duration <= MAX_DURATION
+ *	on_duration = off_duration * (stock_freq - freq) / freq
+ *
+ *      off_duration  =  (freq * DURATION) / stock_freq
+ *      on_duration = DURATION - off_duration
+ *
+ *
+ *---------------------------------------------------------------------------
+ *
+ * ChangeLog:
+ *	Dec. 12, 2003	Hiroshi Miura <miura@da-cha.org>
+ *		- fix on/off register mistake
+ *		- fix cpu_khz calc when it stops cpu modulation.
+ *
+ *	Dec. 11, 2002	Hiroshi Miura <miura@da-cha.org>
+ *		- rewrite for Cyrix MediaGX Cx5510/5520 and
+ *		  NatSemi Geode Cs5530(A).
+ *
+ *	Jul. ??, 2002  Zwane Mwaikambo <zwane@commfireservices.com>
+ *		- cs5530_mod patch for 2.4.19-rc1.
+ *
+ *---------------------------------------------------------------------------
+ *
+ * Todo
+ *	Test on machines with 5510, 5530, 5530A
+ */
+
+/************************************************************************
+ *			Suspend Modulation - Definitions		*
+ ************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/cpufreq.h>
+#include <linux/pci.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+
+#include <asm/processor-cyrix.h>
+
+/* PCI config registers, all at F0 */
+#define PCI_PMER1	0x80	/* power management enable register 1 */
+#define PCI_PMER2	0x81	/* power management enable register 2 */
+#define PCI_PMER3	0x82	/* power management enable register 3 */
+#define PCI_IRQTC	0x8c	/* irq speedup timer counter register:typical 2 to 4ms */
+#define PCI_VIDTC	0x8d	/* video speedup timer counter register: typical 50 to 100ms */
+#define PCI_MODOFF	0x94	/* suspend modulation OFF counter register, 1 = 32us */
+#define PCI_MODON	0x95	/* suspend modulation ON counter register */
+#define PCI_SUSCFG	0x96	/* suspend configuration register */
+
+/* PMER1 bits */
+#define GPM		(1<<0)	/* global power management */
+#define GIT		(1<<1)	/* globally enable PM device idle timers */
+#define GTR		(1<<2)	/* globally enable IO traps */
+#define IRQ_SPDUP	(1<<3)	/* disable clock throttle during interrupt handling */
+#define VID_SPDUP	(1<<4)	/* disable clock throttle during vga video handling */
+
+/* SUSCFG bits */
+#define SUSMOD		(1<<0)	/* enable/disable suspend modulation */
+/* the below is supported only with cs5530 (after rev.1.2)/cs5530A */
+#define SMISPDUP	(1<<1)	/* select how SMI re-enable suspend modulation: */
+				/* IRQTC timer or read SMI speedup disable reg.(F1BAR[08-09h]) */
+#define SUSCFG		(1<<2)	/* enable powering down a GXLV processor. "Special 3Volt Suspend" mode */
+/* the below is supported only with cs5530A */
+#define PWRSVE_ISA	(1<<3)	/* stop ISA clock  */
+#define PWRSVE		(1<<4)	/* active idle */
+
+struct gxfreq_params {
+	u8 on_duration;
+	u8 off_duration;
+	u8 pci_suscfg;
+	u8 pci_pmer1;
+	u8 pci_pmer2;
+	struct pci_dev *cs55x0;
+};
+
+static struct gxfreq_params *gx_params;
+static int stock_freq;
+
+/* PCI bus clock - defaults to 30.000 if cpu_khz is not available */
+static int pci_busclk;
+module_param(pci_busclk, int, 0444);
+
+/* maximum duration for which the cpu may be suspended
+ * (32us * MAX_DURATION). If no parameter is given, this defaults
+ * to 255.
+ * Note that this leads to a maximum of 8 ms(!) where the CPU clock
+ * is suspended -- processing power is just 0.39% of what it used to be,
+ * though. 781.25 kHz(!) for a 200 MHz processor -- wow. */
+static int max_duration = 255;
+module_param(max_duration, int, 0444);
+
+/* For the default policy, we want at least some processing power
+ * - let's say 5%. (min = maxfreq / POLICY_MIN_DIV)
+ */
+#define POLICY_MIN_DIV 20
+
+
+/**
+ * we can detect a core multipiler from dir0_lsb
+ * from GX1 datasheet p.56,
+ *	MULT[3:0]:
+ *	0000 = SYSCLK multiplied by 4 (test only)
+ *	0001 = SYSCLK multiplied by 10
+ *	0010 = SYSCLK multiplied by 4
+ *	0011 = SYSCLK multiplied by 6
+ *	0100 = SYSCLK multiplied by 9
+ *	0101 = SYSCLK multiplied by 5
+ *	0110 = SYSCLK multiplied by 7
+ *	0111 = SYSCLK multiplied by 8
+ *              of 33.3MHz
+ **/
+static int gx_freq_mult[16] = {
+		4, 10, 4, 6, 9, 5, 7, 8,
+		0, 0, 0, 0, 0, 0, 0, 0
+};
+
+
+/****************************************************************
+ *	Low Level chipset interface				*
+ ****************************************************************/
+static struct pci_device_id gx_chipset_tbl[] __initdata = {
+	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY), },
+	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
+	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
+	{ 0, },
+};
+
+static void gx_write_byte(int reg, int value)
+{
+	pci_write_config_byte(gx_params->cs55x0, reg, value);
+}
+
+/**
+ * gx_detect_chipset:
+ *
+ **/
+static __init struct pci_dev *gx_detect_chipset(void)
+{
+	struct pci_dev *gx_pci = NULL;
+
+	/* check if CPU is a MediaGX or a Geode. */
+	if ((boot_cpu_data.x86_vendor != X86_VENDOR_NSC) &&
+	    (boot_cpu_data.x86_vendor != X86_VENDOR_CYRIX)) {
+		pr_debug("error: no MediaGX/Geode processor found!\n");
+		return NULL;
+	}
+
+	/* detect which companion chip is used */
+	for_each_pci_dev(gx_pci) {
+		if ((pci_match_id(gx_chipset_tbl, gx_pci)) != NULL)
+			return gx_pci;
+	}
+
+	pr_debug("error: no supported chipset found!\n");
+	return NULL;
+}
+
+/**
+ * gx_get_cpuspeed:
+ *
+ * Finds out at which efficient frequency the Cyrix MediaGX/NatSemi
+ * Geode CPU runs.
+ */
+static unsigned int gx_get_cpuspeed(unsigned int cpu)
+{
+	if ((gx_params->pci_suscfg & SUSMOD) == 0)
+		return stock_freq;
+
+	return (stock_freq * gx_params->off_duration)
+		/ (gx_params->on_duration + gx_params->off_duration);
+}
+
+/**
+ *      gx_validate_speed:
+ *      determine current cpu speed
+ *
+ **/
+
+static unsigned int gx_validate_speed(unsigned int khz, u8 *on_duration,
+		u8 *off_duration)
+{
+	unsigned int i;
+	u8 tmp_on, tmp_off;
+	int old_tmp_freq = stock_freq;
+	int tmp_freq;
+
+	*off_duration = 1;
+	*on_duration = 0;
+
+	for (i = max_duration; i > 0; i--) {
+		tmp_off = ((khz * i) / stock_freq) & 0xff;
+		tmp_on = i - tmp_off;
+		tmp_freq = (stock_freq * tmp_off) / i;
+		/* if this relation is closer to khz, use this. If it's equal,
+		 * prefer it, too - lower latency */
+		if (abs(tmp_freq - khz) <= abs(old_tmp_freq - khz)) {
+			*on_duration = tmp_on;
+			*off_duration = tmp_off;
+			old_tmp_freq = tmp_freq;
+		}
+	}
+
+	return old_tmp_freq;
+}
+
+
+/**
+ * gx_set_cpuspeed:
+ * set cpu speed in khz.
+ **/
+
+static void gx_set_cpuspeed(unsigned int khz)
+{
+	u8 suscfg, pmer1;
+	unsigned int new_khz;
+	unsigned long flags;
+	struct cpufreq_freqs freqs;
+
+	freqs.cpu = 0;
+	freqs.old = gx_get_cpuspeed(0);
+
+	new_khz = gx_validate_speed(khz, &gx_params->on_duration,
+			&gx_params->off_duration);
+
+	freqs.new = new_khz;
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+	local_irq_save(flags);
+
+
+
+	if (new_khz != stock_freq) {
+		/* if new khz == 100% of CPU speed, it is special case */
+		switch (gx_params->cs55x0->device) {
+		case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
+			pmer1 = gx_params->pci_pmer1 | IRQ_SPDUP | VID_SPDUP;
+			/* FIXME: need to test other values -- Zwane,Miura */
+			/* typical 2 to 4ms */
+			gx_write_byte(PCI_IRQTC, 4);
+			/* typical 50 to 100ms */
+			gx_write_byte(PCI_VIDTC, 100);
+			gx_write_byte(PCI_PMER1, pmer1);
+
+			if (gx_params->cs55x0->revision < 0x10) {
+				/* CS5530(rev 1.2, 1.3) */
+				suscfg = gx_params->pci_suscfg|SUSMOD;
+			} else {
+				/* CS5530A,B.. */
+				suscfg = gx_params->pci_suscfg|SUSMOD|PWRSVE;
+			}
+			break;
+		case PCI_DEVICE_ID_CYRIX_5520:
+		case PCI_DEVICE_ID_CYRIX_5510:
+			suscfg = gx_params->pci_suscfg | SUSMOD;
+			break;
+		default:
+			local_irq_restore(flags);
+			pr_debug("fatal: try to set unknown chipset.\n");
+			return;
+		}
+	} else {
+		suscfg = gx_params->pci_suscfg & ~(SUSMOD);
+		gx_params->off_duration = 0;
+		gx_params->on_duration = 0;
+		pr_debug("suspend modulation disabled: cpu runs 100%% speed.\n");
+	}
+
+	gx_write_byte(PCI_MODOFF, gx_params->off_duration);
+	gx_write_byte(PCI_MODON, gx_params->on_duration);
+
+	gx_write_byte(PCI_SUSCFG, suscfg);
+	pci_read_config_byte(gx_params->cs55x0, PCI_SUSCFG, &suscfg);
+
+	local_irq_restore(flags);
+
+	gx_params->pci_suscfg = suscfg;
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	pr_debug("suspend modulation w/ duration of ON:%d us, OFF:%d us\n",
+		gx_params->on_duration * 32, gx_params->off_duration * 32);
+	pr_debug("suspend modulation w/ clock speed: %d kHz.\n", freqs.new);
+}
+
+/****************************************************************
+ *             High level functions                             *
+ ****************************************************************/
+
+/*
+ *	cpufreq_gx_verify: test if frequency range is valid
+ *
+ *	This function checks if a given frequency range in kHz is valid
+ *      for the hardware supported by the driver.
+ */
+
+static int cpufreq_gx_verify(struct cpufreq_policy *policy)
+{
+	unsigned int tmp_freq = 0;
+	u8 tmp1, tmp2;
+
+	if (!stock_freq || !policy)
+		return -EINVAL;
+
+	policy->cpu = 0;
+	cpufreq_verify_within_limits(policy, (stock_freq / max_duration),
+			stock_freq);
+
+	/* it needs to be assured that at least one supported frequency is
+	 * within policy->min and policy->max. If it is not, policy->max
+	 * needs to be increased until one freuqency is supported.
+	 * policy->min may not be decreased, though. This way we guarantee a
+	 * specific processing capacity.
+	 */
+	tmp_freq = gx_validate_speed(policy->min, &tmp1, &tmp2);
+	if (tmp_freq < policy->min)
+		tmp_freq += stock_freq / max_duration;
+	policy->min = tmp_freq;
+	if (policy->min > policy->max)
+		policy->max = tmp_freq;
+	tmp_freq = gx_validate_speed(policy->max, &tmp1, &tmp2);
+	if (tmp_freq > policy->max)
+		tmp_freq -= stock_freq / max_duration;
+	policy->max = tmp_freq;
+	if (policy->max < policy->min)
+		policy->max = policy->min;
+	cpufreq_verify_within_limits(policy, (stock_freq / max_duration),
+			stock_freq);
+
+	return 0;
+}
+
+/*
+ *      cpufreq_gx_target:
+ *
+ */
+static int cpufreq_gx_target(struct cpufreq_policy *policy,
+			     unsigned int target_freq,
+			     unsigned int relation)
+{
+	u8 tmp1, tmp2;
+	unsigned int tmp_freq;
+
+	if (!stock_freq || !policy)
+		return -EINVAL;
+
+	policy->cpu = 0;
+
+	tmp_freq = gx_validate_speed(target_freq, &tmp1, &tmp2);
+	while (tmp_freq < policy->min) {
+		tmp_freq += stock_freq / max_duration;
+		tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2);
+	}
+	while (tmp_freq > policy->max) {
+		tmp_freq -= stock_freq / max_duration;
+		tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2);
+	}
+
+	gx_set_cpuspeed(tmp_freq);
+
+	return 0;
+}
+
+static int cpufreq_gx_cpu_init(struct cpufreq_policy *policy)
+{
+	unsigned int maxfreq, curfreq;
+
+	if (!policy || policy->cpu != 0)
+		return -ENODEV;
+
+	/* determine maximum frequency */
+	if (pci_busclk)
+		maxfreq = pci_busclk * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f];
+	else if (cpu_khz)
+		maxfreq = cpu_khz;
+	else
+		maxfreq = 30000 * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f];
+
+	stock_freq = maxfreq;
+	curfreq = gx_get_cpuspeed(0);
+
+	pr_debug("cpu max frequency is %d.\n", maxfreq);
+	pr_debug("cpu current frequency is %dkHz.\n", curfreq);
+
+	/* setup basic struct for cpufreq API */
+	policy->cpu = 0;
+
+	if (max_duration < POLICY_MIN_DIV)
+		policy->min = maxfreq / max_duration;
+	else
+		policy->min = maxfreq / POLICY_MIN_DIV;
+	policy->max = maxfreq;
+	policy->cur = curfreq;
+	policy->cpuinfo.min_freq = maxfreq / max_duration;
+	policy->cpuinfo.max_freq = maxfreq;
+	policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+
+	return 0;
+}
+
+/*
+ * cpufreq_gx_init:
+ *   MediaGX/Geode GX initialize cpufreq driver
+ */
+static struct cpufreq_driver gx_suspmod_driver = {
+	.get		= gx_get_cpuspeed,
+	.verify		= cpufreq_gx_verify,
+	.target		= cpufreq_gx_target,
+	.init		= cpufreq_gx_cpu_init,
+	.name		= "gx-suspmod",
+	.owner		= THIS_MODULE,
+};
+
+static int __init cpufreq_gx_init(void)
+{
+	int ret;
+	struct gxfreq_params *params;
+	struct pci_dev *gx_pci;
+
+	/* Test if we have the right hardware */
+	gx_pci = gx_detect_chipset();
+	if (gx_pci == NULL)
+		return -ENODEV;
+
+	/* check whether module parameters are sane */
+	if (max_duration > 0xff)
+		max_duration = 0xff;
+
+	pr_debug("geode suspend modulation available.\n");
+
+	params = kzalloc(sizeof(struct gxfreq_params), GFP_KERNEL);
+	if (params == NULL)
+		return -ENOMEM;
+
+	params->cs55x0 = gx_pci;
+	gx_params = params;
+
+	/* keep cs55x0 configurations */
+	pci_read_config_byte(params->cs55x0, PCI_SUSCFG, &(params->pci_suscfg));
+	pci_read_config_byte(params->cs55x0, PCI_PMER1, &(params->pci_pmer1));
+	pci_read_config_byte(params->cs55x0, PCI_PMER2, &(params->pci_pmer2));
+	pci_read_config_byte(params->cs55x0, PCI_MODON, &(params->on_duration));
+	pci_read_config_byte(params->cs55x0, PCI_MODOFF,
+			&(params->off_duration));
+
+	ret = cpufreq_register_driver(&gx_suspmod_driver);
+	if (ret) {
+		kfree(params);
+		return ret;                   /* register error! */
+	}
+
+	return 0;
+}
+
+static void __exit cpufreq_gx_exit(void)
+{
+	cpufreq_unregister_driver(&gx_suspmod_driver);
+	pci_dev_put(gx_params->cs55x0);
+	kfree(gx_params);
+}
+
+MODULE_AUTHOR("Hiroshi Miura <miura@da-cha.org>");
+MODULE_DESCRIPTION("Cpufreq driver for Cyrix MediaGX and NatSemi Geode");
+MODULE_LICENSE("GPL");
+
+module_init(cpufreq_gx_init);
+module_exit(cpufreq_gx_exit);
+