Merge branch 'tip/perf/jump-label-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/urgent

5 files changed, 311 insertions, 18 deletions

diff --git a/drivers/firewire/Kconfig b/drivers/firewire/Kconfig
index fcf3ea28340..40a222e19b2 100644
--- a/drivers/firewire/Kconfig
+++ b/drivers/firewire/Kconfig
@@ -3,9 +3,6 @@ menu "IEEE 1394 (FireWire) support"
 	# firewire-core does not depend on PCI but is
 	# not useful without PCI controller driver
 
-comment "You can enable one or both FireWire driver stacks."
-comment "The newer stack is recommended."
-
 config FIREWIRE
 	tristate "FireWire driver stack"
 	select CRC_ITU_T
@@ -64,8 +61,6 @@ config FIREWIRE_NET
 	  To compile this driver as a module, say M here:  The module will be
 	  called firewire-net.
 
-source "drivers/ieee1394/Kconfig"
-
 config FIREWIRE_NOSY
 	tristate "Nosy - a FireWire traffic sniffer for PCILynx cards"
 	depends on PCI
diff --git a/drivers/firewire/Makefile b/drivers/firewire/Makefile
index 3c6a7fb20aa..e3870d5c43d 100644
--- a/drivers/firewire/Makefile
+++ b/drivers/firewire/Makefile
@@ -13,3 +13,4 @@ obj-$(CONFIG_FIREWIRE_OHCI) += firewire-ohci.o
 obj-$(CONFIG_FIREWIRE_SBP2) += firewire-sbp2.o
 obj-$(CONFIG_FIREWIRE_NET)  += firewire-net.o
 obj-$(CONFIG_FIREWIRE_NOSY) += nosy.o
+obj-$(CONFIG_PROVIDE_OHCI1394_DMA_INIT) += init_ohci1394_dma.o
diff --git a/drivers/firewire/init_ohci1394_dma.c b/drivers/firewire/init_ohci1394_dma.c
new file mode 100644
index 00000000000..a9a347adb35
--- /dev/null
+++ b/drivers/firewire/init_ohci1394_dma.c
@@ -0,0 +1,309 @@
+/*
+ * init_ohci1394_dma.c - Initializes physical DMA on all OHCI 1394 controllers
+ *
+ * Copyright (C) 2006-2007      Bernhard Kaindl <bk@suse.de>
+ *
+ * Derived from drivers/ieee1394/ohci1394.c and arch/x86/kernel/early-quirks.c
+ * this file has functions to:
+ * - scan the PCI very early on boot for all OHCI 1394-compliant controllers
+ * - reset and initialize them and make them join the IEEE1394 bus and
+ * - enable physical DMA on them to allow remote debugging
+ *
+ * All code and data is marked as __init and __initdata, respective as
+ * during boot, all OHCI1394 controllers may be claimed by the firewire
+ * stack and at this point, this code should not touch them anymore.
+ *
+ * To use physical DMA after the initialization of the firewire stack,
+ * be sure that the stack enables it and (re-)attach after the bus reset
+ * which may be caused by the firewire stack initialization.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software Foundation,
+ * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>		/* for PCI defines */
+#include <linux/string.h>
+
+#include <asm/pci-direct.h>	/* for direct PCI config space access */
+#include <asm/fixmap.h>
+
+#include <linux/init_ohci1394_dma.h>
+#include "ohci.h"
+
+int __initdata init_ohci1394_dma_early;
+
+struct ohci {
+	void __iomem *registers;
+};
+
+static inline void reg_write(const struct ohci *ohci, int offset, u32 data)
+{
+	writel(data, ohci->registers + offset);
+}
+
+static inline u32 reg_read(const struct ohci *ohci, int offset)
+{
+	return readl(ohci->registers + offset);
+}
+
+#define OHCI_LOOP_COUNT		100	/* Number of loops for reg read waits */
+
+/* Reads a PHY register of an OHCI-1394 controller */
+static inline u8 __init get_phy_reg(struct ohci *ohci, u8 addr)
+{
+	int i;
+	u32 r;
+
+	reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | 0x00008000);
+
+	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
+		if (reg_read(ohci, OHCI1394_PhyControl) & 0x80000000)
+			break;
+		mdelay(1);
+	}
+	r = reg_read(ohci, OHCI1394_PhyControl);
+
+	return (r & 0x00ff0000) >> 16;
+}
+
+/* Writes to a PHY register of an OHCI-1394 controller */
+static inline void __init set_phy_reg(struct ohci *ohci, u8 addr, u8 data)
+{
+	int i;
+
+	reg_write(ohci, OHCI1394_PhyControl, (addr << 8) | data | 0x00004000);
+
+	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
+		if (!(reg_read(ohci, OHCI1394_PhyControl) & 0x00004000))
+			break;
+		mdelay(1);
+	}
+}
+
+/* Resets an OHCI-1394 controller (for sane state before initialization) */
+static inline void __init init_ohci1394_soft_reset(struct ohci *ohci)
+{
+	int i;
+
+	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_softReset);
+
+	for (i = 0; i < OHCI_LOOP_COUNT; i++) {
+		if (!(reg_read(ohci, OHCI1394_HCControlSet)
+				   & OHCI1394_HCControl_softReset))
+			break;
+		mdelay(1);
+	}
+}
+
+#define OHCI1394_MAX_AT_REQ_RETRIES	0xf
+#define OHCI1394_MAX_AT_RESP_RETRIES	0x2
+#define OHCI1394_MAX_PHYS_RESP_RETRIES	0x8
+
+/* Basic OHCI-1394 register and port inititalization */
+static inline void __init init_ohci1394_initialize(struct ohci *ohci)
+{
+	u32 bus_options;
+	int num_ports, i;
+
+	/* Put some defaults to these undefined bus options */
+	bus_options = reg_read(ohci, OHCI1394_BusOptions);
+	bus_options |=  0x60000000; /* Enable CMC and ISC */
+	bus_options &= ~0x00ff0000; /* XXX: Set cyc_clk_acc to zero for now */
+	bus_options &= ~0x18000000; /* Disable PMC and BMC */
+	reg_write(ohci, OHCI1394_BusOptions, bus_options);
+
+	/* Set the bus number */
+	reg_write(ohci, OHCI1394_NodeID, 0x0000ffc0);
+
+	/* Enable posted writes */
+	reg_write(ohci, OHCI1394_HCControlSet,
+			OHCI1394_HCControl_postedWriteEnable);
+
+	/* Clear link control register */
+	reg_write(ohci, OHCI1394_LinkControlClear, 0xffffffff);
+
+	/* enable phys */
+	reg_write(ohci, OHCI1394_LinkControlSet,
+			OHCI1394_LinkControl_rcvPhyPkt);
+
+	/* Don't accept phy packets into AR request context */
+	reg_write(ohci, OHCI1394_LinkControlClear, 0x00000400);
+
+	/* Clear the Isochonouys interrupt masks */
+	reg_write(ohci, OHCI1394_IsoRecvIntMaskClear, 0xffffffff);
+	reg_write(ohci, OHCI1394_IsoRecvIntEventClear, 0xffffffff);
+	reg_write(ohci, OHCI1394_IsoXmitIntMaskClear, 0xffffffff);
+	reg_write(ohci, OHCI1394_IsoXmitIntEventClear, 0xffffffff);
+
+	/* Accept asyncronous transfer requests from all nodes for now */
+	reg_write(ohci, OHCI1394_AsReqFilterHiSet, 0x80000000);
+
+	/* Specify asyncronous transfer retries */
+	reg_write(ohci, OHCI1394_ATRetries,
+		  OHCI1394_MAX_AT_REQ_RETRIES |
+		  (OHCI1394_MAX_AT_RESP_RETRIES<<4) |
+		  (OHCI1394_MAX_PHYS_RESP_RETRIES<<8));
+
+	/* We don't want hardware swapping */
+	reg_write(ohci, OHCI1394_HCControlClear,
+		  OHCI1394_HCControl_noByteSwapData);
+
+	/* Enable link */
+	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_linkEnable);
+
+	/* If anything is connected to a port, make sure it is enabled */
+	num_ports = get_phy_reg(ohci, 2) & 0xf;
+	for (i = 0; i < num_ports; i++) {
+		unsigned int status;
+
+		set_phy_reg(ohci, 7, i);
+		status = get_phy_reg(ohci, 8);
+
+		if (status & 0x20)
+			set_phy_reg(ohci, 8, status & ~1);
+	}
+}
+
+/**
+ * init_ohci1394_wait_for_busresets - wait until bus resets are completed
+ *
+ * OHCI1394 initialization itself and any device going on- or offline
+ * and any cable issue cause a IEEE1394 bus reset. The OHCI1394 spec
+ * specifies that physical DMA is disabled on each bus reset and it
+ * has to be enabled after each bus reset when needed. We resort
+ * to polling here because on early boot, we have no interrupts.
+ */
+static inline void __init init_ohci1394_wait_for_busresets(struct ohci *ohci)
+{
+	int i, events;
+
+	for (i = 0; i < 9; i++) {
+		mdelay(200);
+		events = reg_read(ohci, OHCI1394_IntEventSet);
+		if (events & OHCI1394_busReset)
+			reg_write(ohci, OHCI1394_IntEventClear,
+					OHCI1394_busReset);
+	}
+}
+
+/**
+ * init_ohci1394_enable_physical_dma - Enable physical DMA for remote debugging
+ * This enables remote DMA access over IEEE1394 from every host for the low
+ * 4GB of address space. DMA accesses above 4GB are not available currently.
+ */
+static inline void __init init_ohci1394_enable_physical_dma(struct ohci *ohci)
+{
+	reg_write(ohci, OHCI1394_PhyReqFilterHiSet, 0xffffffff);
+	reg_write(ohci, OHCI1394_PhyReqFilterLoSet, 0xffffffff);
+	reg_write(ohci, OHCI1394_PhyUpperBound, 0xffff0000);
+}
+
+/**
+ * init_ohci1394_reset_and_init_dma - init controller and enable DMA
+ * This initializes the given controller and enables physical DMA engine in it.
+ */
+static inline void __init init_ohci1394_reset_and_init_dma(struct ohci *ohci)
+{
+	/* Start off with a soft reset, clears everything to a sane state. */
+	init_ohci1394_soft_reset(ohci);
+
+	/* Accessing some registers without LPS enabled may cause lock up */
+	reg_write(ohci, OHCI1394_HCControlSet, OHCI1394_HCControl_LPS);
+
+	/* Disable and clear interrupts */
+	reg_write(ohci, OHCI1394_IntEventClear, 0xffffffff);
+	reg_write(ohci, OHCI1394_IntMaskClear, 0xffffffff);
+
+	mdelay(50); /* Wait 50msec to make sure we have full link enabled */
+
+	init_ohci1394_initialize(ohci);
+	/*
+	 * The initialization causes at least one IEEE1394 bus reset. Enabling
+	 * physical DMA only works *after* *all* bus resets have calmed down:
+	 */
+	init_ohci1394_wait_for_busresets(ohci);
+
+	/* We had to wait and do this now if we want to debug early problems */
+	init_ohci1394_enable_physical_dma(ohci);
+}
+
+/**
+ * init_ohci1394_controller - Map the registers of the controller and init DMA
+ * This maps the registers of the specified controller and initializes it
+ */
+static inline void __init init_ohci1394_controller(int num, int slot, int func)
+{
+	unsigned long ohci_base;
+	struct ohci ohci;
+
+	printk(KERN_INFO "init_ohci1394_dma: initializing OHCI-1394"
+			 " at %02x:%02x.%x\n", num, slot, func);
+
+	ohci_base = read_pci_config(num, slot, func, PCI_BASE_ADDRESS_0+(0<<2))
+						   & PCI_BASE_ADDRESS_MEM_MASK;
+
+	set_fixmap_nocache(FIX_OHCI1394_BASE, ohci_base);
+
+	ohci.registers = (void __iomem *)fix_to_virt(FIX_OHCI1394_BASE);
+
+	init_ohci1394_reset_and_init_dma(&ohci);
+}
+
+/**
+ * debug_init_ohci1394_dma - scan for OHCI1394 controllers and init DMA on them
+ * Scans the whole PCI space for OHCI1394 controllers and inits DMA on them
+ */
+void __init init_ohci1394_dma_on_all_controllers(void)
+{
+	int num, slot, func;
+	u32 class;
+
+	if (!early_pci_allowed())
+		return;
+
+	/* Poor man's PCI discovery, the only thing we can do at early boot */
+	for (num = 0; num < 32; num++) {
+		for (slot = 0; slot < 32; slot++) {
+			for (func = 0; func < 8; func++) {
+				class = read_pci_config(num, slot, func,
+							PCI_CLASS_REVISION);
+				if (class == 0xffffffff)
+					continue; /* No device at this func */
+
+				if (class>>8 != PCI_CLASS_SERIAL_FIREWIRE_OHCI)
+					continue; /* Not an OHCI-1394 device */
+
+				init_ohci1394_controller(num, slot, func);
+				break; /* Assume one controller per device */
+			}
+		}
+	}
+	printk(KERN_INFO "init_ohci1394_dma: finished initializing OHCI DMA\n");
+}
+
+/**
+ * setup_init_ohci1394_early - enables early OHCI1394 DMA initialization
+ */
+static int __init setup_ohci1394_dma(char *opt)
+{
+	if (!strcmp(opt, "early"))
+		init_ohci1394_dma_early = 1;
+	return 0;
+}
+
+/* passing ohci1394_dma=early on boot causes early OHCI1394 DMA initialization */
+early_param("ohci1394_dma", setup_ohci1394_dma);
diff --git a/drivers/firewire/net.c b/drivers/firewire/net.c
index 33f8421c71c..18fdd9703b4 100644
--- a/drivers/firewire/net.c
+++ b/drivers/firewire/net.c
@@ -8,7 +8,6 @@
 
 #include <linux/bug.h>
 #include <linux/device.h>
-#include <linux/ethtool.h>
 #include <linux/firewire.h>
 #include <linux/firewire-constants.h>
 #include <linux/highmem.h>
@@ -1361,17 +1360,6 @@ static int fwnet_change_mtu(struct net_device *net, int new_mtu)
 	return 0;
 }
 
-static void fwnet_get_drvinfo(struct net_device *net,
-			      struct ethtool_drvinfo *info)
-{
-	strcpy(info->driver, KBUILD_MODNAME);
-	strcpy(info->bus_info, "ieee1394");
-}
-
-static const struct ethtool_ops fwnet_ethtool_ops = {
-	.get_drvinfo = fwnet_get_drvinfo,
-};
-
 static const struct net_device_ops fwnet_netdev_ops = {
 	.ndo_open       = fwnet_open,
 	.ndo_stop	= fwnet_stop,
@@ -1390,7 +1378,6 @@ static void fwnet_init_dev(struct net_device *net)
 	net->hard_header_len	= FWNET_HLEN;
 	net->type		= ARPHRD_IEEE1394;
 	net->tx_queue_len	= 10;
-	SET_ETHTOOL_OPS(net, &fwnet_ethtool_ops);
 }
 
 /* caller must hold fwnet_device_mutex */
diff --git a/drivers/firewire/nosy.c b/drivers/firewire/nosy.c
index 8528b10763e..bf184fb59a5 100644
--- a/drivers/firewire/nosy.c
+++ b/drivers/firewire/nosy.c
@@ -405,6 +405,7 @@ static const struct file_operations nosy_ops = {
 	.poll =			nosy_poll,
 	.open =			nosy_open,
 	.release =		nosy_release,
+	.llseek =		noop_llseek,
 };
 
 #define PHY_PACKET_SIZE 12 /* 1 payload, 1 inverse, 1 ack = 3 quadlets */