Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c changes from Wolfram Sang:

 - an arbitration driver.  While the driver is quite simple, it caused
   discussion if we need additional arbitration on top of the one
   specified in the I2C standard.  Conclusion is that I accept a few
   generic mechanisms, but not very specific ones.

 - the core lost the detach_adapter() call.  It has no users anymore and
   was in the way for other cleanups.  attach_adapter() is sadly still
   there since there are users waiting to be converted.

 - the core gained a bus recovery infrastructure.  I2C defines a way to
   recover if the data line is stalled.  This mechanism is now in the
   core and drivers can now pass some data to make use of it.

 - bigger driver cleanups for designware, s3c2410

 - removing superfluous refcounting from drivers

 - removing Ben Dooks as second maintainer due to inactivity.  Thanks
   for all your work so far, Ben!

 - bugfixes, feature additions, devicetree fixups, simplifications...

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
  i2c: xiic: must always write 16-bit words to TX_FIFO
  i2c: octeon: use HZ in timeout value
  i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
  i2c: designware-pci: drop superfluous {get|put}_device
  i2c: designware-plat: drop superfluous {get|put}_device
  i2c: davinci: drop superfluous {get|put}_device
  MAINTAINERS: Ben Dooks is inactive regarding I2C
  i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
  i2c: at91: convert to dma_request_slave_channel_compat()
  i2c: mxs: do error checking and handling in PIO mode
  i2c: mxs: remove races in PIO code
  i2c-designware: switch to use runtime PM autosuspend
  i2c-designware: use usleep_range() in the busy-loop
  i2c-designware: enable/disable the controller properly
  i2c-designware: use dynamic adapter numbering on Lynxpoint
  i2c-designware-pci: use managed functions pcim_* and devm_*
  i2c-designware-pci: use dev_err() instead of printk()
  i2c-designware: move to managed functions (devm_*)
  i2c: remove CONFIG_HOTPLUG ifdefs
  i2c: s3c2410: Add SMBus emulation for block read
  ...

1 files changed, 28 insertions, 30 deletions

diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 75195e3f5dd..6bb839b688b 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -603,15 +603,18 @@ static const struct of_device_id atmel_twi_dt_ids[] = {
 	}
 };
 MODULE_DEVICE_TABLE(of, atmel_twi_dt_ids);
-#else
-#define atmel_twi_dt_ids NULL
 #endif
 
-static bool filter(struct dma_chan *chan, void *slave)
+static bool filter(struct dma_chan *chan, void *pdata)
 {
-	struct at_dma_slave *sl = slave;
+	struct at91_twi_pdata *sl_pdata = pdata;
+	struct at_dma_slave *sl;
+
+	if (!sl_pdata)
+		return false;
 
-	if (sl->dma_dev == chan->device->dev) {
+	sl = &sl_pdata->dma_slave;
+	if (sl && (sl->dma_dev == chan->device->dev)) {
 		chan->private = sl;
 		return true;
 	} else {
@@ -622,11 +625,10 @@ static bool filter(struct dma_chan *chan, void *slave)
 static int at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr)
 {
 	int ret = 0;
-	struct at_dma_slave *sdata;
+	struct at91_twi_pdata *pdata = dev->pdata;
 	struct dma_slave_config slave_config;
 	struct at91_twi_dma *dma = &dev->dma;
-
-	sdata = &dev->pdata->dma_slave;
+	dma_cap_mask_t mask;
 
 	memset(&slave_config, 0, sizeof(slave_config));
 	slave_config.src_addr = (dma_addr_t)phy_addr + AT91_TWI_RHR;
@@ -637,25 +639,22 @@ static int at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr)
 	slave_config.dst_maxburst = 1;
 	slave_config.device_fc = false;
 
-	if (sdata && sdata->dma_dev) {
-		dma_cap_mask_t mask;
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
 
-		dma_cap_zero(mask);
-		dma_cap_set(DMA_SLAVE, mask);
-		dma->chan_tx = dma_request_channel(mask, filter, sdata);
-		if (!dma->chan_tx) {
-			dev_err(dev->dev, "no DMA channel available for tx\n");
-			ret = -EBUSY;
-			goto error;
-		}
-		dma->chan_rx = dma_request_channel(mask, filter, sdata);
-		if (!dma->chan_rx) {
-			dev_err(dev->dev, "no DMA channel available for rx\n");
-			ret = -EBUSY;
-			goto error;
-		}
-	} else {
-		ret = -EINVAL;
+	dma->chan_tx = dma_request_slave_channel_compat(mask, filter, pdata,
+							dev->dev, "tx");
+	if (!dma->chan_tx) {
+		dev_err(dev->dev, "can't get a DMA channel for tx\n");
+		ret = -EBUSY;
+		goto error;
+	}
+
+	dma->chan_rx = dma_request_slave_channel_compat(mask, filter, pdata,
+							dev->dev, "rx");
+	if (!dma->chan_rx) {
+		dev_err(dev->dev, "can't get a DMA channel for rx\n");
+		ret = -EBUSY;
 		goto error;
 	}
 
@@ -785,12 +784,11 @@ static int at91_twi_probe(struct platform_device *pdev)
 static int at91_twi_remove(struct platform_device *pdev)
 {
 	struct at91_twi_dev *dev = platform_get_drvdata(pdev);
-	int rc;
 
-	rc = i2c_del_adapter(&dev->adapter);
+	i2c_del_adapter(&dev->adapter);
 	clk_disable_unprepare(dev->clk);
 
-	return rc;
+	return 0;
 }
 
 #ifdef CONFIG_PM
@@ -828,7 +826,7 @@ static struct platform_driver at91_twi_driver = {
 	.driver		= {
 		.name	= "at91_i2c",
 		.owner	= THIS_MODULE,
-		.of_match_table = atmel_twi_dt_ids,
+		.of_match_table = of_match_ptr(atmel_twi_dt_ids),
 		.pm	= at91_twi_pm_ops,
 	},
 };