i2c: Group bus drivers by type

The list of I2C/SMBus bus drivers is growing and it is sometimes
difficult for the users to figure out what drivers they should enable.
By grouping the drivers by type, I hope to make the selection easier.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

2 files changed, 370 insertions, 344 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 37f5b84e0e9..2b0874b0ad1 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -4,6 +4,9 @@
 
 menu "I2C Hardware Bus support"
 
+comment "PC SMBus host controller drivers"
+	depends on PCI
+
 config I2C_ALI1535
 	tristate "ALI 1535"
 	depends on PCI
@@ -73,6 +76,176 @@ config I2C_AMD8111
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-amd8111.
 
+config I2C_I801
+	tristate "Intel 82801 (ICH)"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the Intel
+	  801 family of mainboard I2C interfaces.  Specifically, the following
+	  versions of the chipset are supported:
+	    82801AA
+	    82801AB
+	    82801BA
+	    82801CA/CAM
+	    82801DB
+	    82801EB/ER (ICH5/ICH5R)
+	    6300ESB
+	    ICH6
+	    ICH7
+	    ESB2
+	    ICH8
+	    ICH9
+	    Tolapai
+	    ICH10
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-i801.
+
+config I2C_PIIX4
+	tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the Intel
+	  PIIX4 family of mainboard I2C interfaces.  Specifically, the following
+	  versions of the chipset are supported (note that Serverworks is part
+	  of Broadcom):
+	    Intel PIIX4
+	    Intel 440MX
+	    ATI IXP200
+	    ATI IXP300
+	    ATI IXP400
+	    ATI SB600
+	    ATI SB700
+	    ATI SB800
+	    Serverworks OSB4
+	    Serverworks CSB5
+	    Serverworks CSB6
+	    Serverworks HT-1000
+	    SMSC Victory66
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-piix4.
+
+config I2C_NFORCE2
+	tristate "Nvidia nForce2, nForce3 and nForce4"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the Nvidia
+	  nForce2, nForce3 and nForce4 families of mainboard I2C interfaces.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-nforce2.
+
+config I2C_NFORCE2_S4985
+	tristate "SMBus multiplexing on the Tyan S4985"
+	depends on I2C_NFORCE2 && EXPERIMENTAL
+	help
+	  Enabling this option will add specific SMBus support for the Tyan
+	  S4985 motherboard.  On this 4-CPU board, the SMBus is multiplexed
+	  over 4 different channels, where the various memory module EEPROMs
+	  live.  Saying yes here will give you access to these in addition
+	  to the trunk.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-nforce2-s4985.
+
+config I2C_SIS5595
+	tristate "SiS 5595"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the
+	  SiS5595 SMBus (a subset of I2C) interface.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-sis5595.
+
+config I2C_SIS630
+	tristate "SiS 630/730"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the
+	  SiS630 and SiS730 SMBus (a subset of I2C) interface.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-sis630.
+
+config I2C_SIS96X
+	tristate "SiS 96x"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the SiS
+	  96x SMBus (a subset of I2C) interfaces.  Specifically, the following
+	  chipsets are supported:
+	    645/961
+	    645DX/961
+	    645DX/962
+	    648/961
+	    650/961
+	    735
+	    745
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-sis96x.
+
+config I2C_VIA
+	tristate "VIA VT82C586B"
+	depends on PCI && EXPERIMENTAL
+	select I2C_ALGOBIT
+	help
+	  If you say yes to this option, support will be included for the VIA
+          82C586B I2C interface
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-via.
+
+config I2C_VIAPRO
+	tristate "VIA VT82C596/82C686/82xx and CX700"
+	depends on PCI
+	help
+	  If you say yes to this option, support will be included for the VIA
+	  VT82C596 and later SMBus interface.  Specifically, the following
+	  chipsets are supported:
+	    VT82C596A/B
+	    VT82C686A/B
+	    VT8231
+	    VT8233/A
+	    VT8235
+	    VT8237R/A/S
+	    VT8251
+	    CX700
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-viapro.
+
+comment "Mac SMBus host controller drivers"
+	depends on PPC_CHRP || PPC_PMAC
+
+config I2C_HYDRA
+	tristate "CHRP Apple Hydra Mac I/O I2C interface"
+	depends on PCI && PPC_CHRP && EXPERIMENTAL
+	select I2C_ALGOBIT
+	help
+	  This supports the use of the I2C interface in the Apple Hydra Mac
+	  I/O chip on some CHRP machines (e.g. the LongTrail).  Say Y if you
+	  have such a machine.
+
+	  This support is also available as a module.  If so, the module
+	  will be called i2c-hydra.
+
+config I2C_POWERMAC
+	tristate "Powermac I2C interface"
+	depends on PPC_PMAC
+	default y
+	help
+	  This exposes the various PowerMac i2c interfaces to the linux i2c
+	  layer and to userland. It is used by various drivers on the PowerMac
+	  platform, and should generally be enabled.
+
+	  This support is also available as a module.  If so, the module
+	  will be called i2c-powermac.
+
+comment "I2C system bus drivers (mostly embedded / system-on-chip)"
+
 config I2C_AT91
 	tristate "Atmel AT91 I2C Two-Wire interface (TWI)"
 	depends on ARCH_AT91 && EXPERIMENTAL && BROKEN
@@ -129,17 +302,6 @@ config I2C_DAVINCI
 	  devices such as DaVinci NIC.
 	  For details please see http://www.ti.com/davinci
 
-config I2C_ELEKTOR
-	tristate "Elektor ISA card"
-	depends on ISA && BROKEN_ON_SMP
-	select I2C_ALGOPCF
-	help
-	  This supports the PCF8584 ISA bus I2C adapter.  Say Y if you own
-	  such an adapter.
-
-	  This support is also available as a module.  If so, the module
-	  will be called i2c-elektor.
-
 config I2C_GPIO
 	tristate "GPIO-based bitbanging I2C"
 	depends on GENERIC_GPIO
@@ -148,84 +310,6 @@ config I2C_GPIO
 	  This is a very simple bitbanging I2C driver utilizing the
 	  arch-neutral GPIO API to control the SCL and SDA lines.
 
-config I2C_HYDRA
-	tristate "CHRP Apple Hydra Mac I/O I2C interface"
-	depends on PCI && PPC_CHRP && EXPERIMENTAL
-	select I2C_ALGOBIT
-	help
-	  This supports the use of the I2C interface in the Apple Hydra Mac
-	  I/O chip on some CHRP machines (e.g. the LongTrail).  Say Y if you
-	  have such a machine.
-
-	  This support is also available as a module.  If so, the module
-	  will be called i2c-hydra.
-
-config I2C_I801
-	tristate "Intel 82801 (ICH)"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the Intel
-	  801 family of mainboard I2C interfaces.  Specifically, the following
-	  versions of the chipset are supported:
-	    82801AA
-	    82801AB
-	    82801BA
-	    82801CA/CAM
-	    82801DB
-	    82801EB/ER (ICH5/ICH5R)
-	    6300ESB
-	    ICH6
-	    ICH7
-	    ESB2
-	    ICH8
-	    ICH9
-	    Tolapai
-	    ICH10
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-i801.
-
-config I2C_PXA
-	tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && ARCH_PXA
-	help
-	  If you have devices in the PXA I2C bus, say yes to this option.
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-pxa.
-
-config I2C_PXA_SLAVE
-	bool "Intel PXA2XX I2C Slave comms support"
-	depends on I2C_PXA
-	help
-	  Support I2C slave mode communications on the PXA I2C bus.  This
-	  is necessary for systems where the PXA may be a target on the
-	  I2C bus.
-
-config I2C_PIIX4
-	tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the Intel
-	  PIIX4 family of mainboard I2C interfaces.  Specifically, the following
-	  versions of the chipset are supported (note that Serverworks is part
-	  of Broadcom):
-	    Intel PIIX4
-	    Intel 440MX
-	    ATI IXP200
-	    ATI IXP300
-	    ATI IXP400
-	    ATI SB600
-	    ATI SB700
-	    ATI SB800
-	    Serverworks OSB4
-	    Serverworks CSB5
-	    Serverworks CSB6
-	    Serverworks HT-1000
-	    SMSC Victory66
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-piix4.
-
 config I2C_IBM_IIC
 	tristate "IBM PPC 4xx on-chip I2C interface"
 	depends on 4xx
@@ -260,18 +344,6 @@ config I2C_IXP2000
 	  This driver is deprecated and will be dropped soon. Use i2c-gpio
 	  instead.
 
-config I2C_POWERMAC
-	tristate "Powermac I2C interface"
-	depends on PPC_PMAC
-	default y
-	help
-	  This exposes the various PowerMac i2c interfaces to the linux i2c
-	  layer and to userland. It is used by various drivers on the PowerMac
-	  platform, and should generally be enabled.
-
-	  This support is also available as a module.  If so, the module
-	  will be called i2c-powermac.
-
 config I2C_MPC
 	tristate "MPC107/824x/85xx/52xx/86xx"
 	depends on PPC32
@@ -284,28 +356,15 @@ config I2C_MPC
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-mpc.
 
-config I2C_NFORCE2
-	tristate "Nvidia nForce2, nForce3 and nForce4"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the Nvidia
-	  nForce2, nForce3 and nForce4 families of mainboard I2C interfaces.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-nforce2.
-
-config I2C_NFORCE2_S4985
-	tristate "SMBus multiplexing on the Tyan S4985"
-	depends on I2C_NFORCE2 && EXPERIMENTAL
+config I2C_MV64XXX
+	tristate "Marvell mv64xxx I2C Controller"
+	depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL
 	help
-	  Enabling this option will add specific SMBus support for the Tyan
-	  S4985 motherboard.  On this 4-CPU board, the SMBus is multiplexed
-	  over 4 different channels, where the various memory module EEPROMs
-	  live.  Saying yes here will give you access to these in addition
-	  to the trunk.
+	  If you say yes to this option, support will be included for the
+	  built-in I2C interface on the Marvell 64xxx line of host bridges.
 
 	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-nforce2-s4985.
+	  will be called i2c-mv64xxx.
 
 config I2C_OCORES
 	tristate "OpenCores I2C Controller"
@@ -328,6 +387,89 @@ config I2C_OMAP
 	  Like OMAP1510/1610/1710/5912 and OMAP242x.
 	  For details see http://www.ti.com/omap.
 
+config I2C_PASEMI
+	tristate "PA Semi SMBus interface"
+	depends on PPC_PASEMI && PCI
+	help
+	  Supports the PA Semi PWRficient on-chip SMBus interfaces.
+
+config I2C_PNX
+	tristate "I2C bus support for Philips PNX targets"
+	depends on ARCH_PNX4008
+	help
+	  This driver supports the Philips IP3204 I2C IP block master and/or
+	  slave controller
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-pnx.
+
+config I2C_PXA
+	tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && ARCH_PXA
+	help
+	  If you have devices in the PXA I2C bus, say yes to this option.
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-pxa.
+
+config I2C_PXA_SLAVE
+	bool "Intel PXA2XX I2C Slave comms support"
+	depends on I2C_PXA
+	help
+	  Support I2C slave mode communications on the PXA I2C bus.  This
+	  is necessary for systems where the PXA may be a target on the
+	  I2C bus.
+
+config I2C_S3C2410
+	tristate "S3C2410 I2C Driver"
+	depends on ARCH_S3C2410
+	help
+	  Say Y here to include support for I2C controller in the
+	  Samsung S3C2410 based System-on-Chip devices.
+
+config I2C_SH7760
+	tristate "Renesas SH7760 I2C Controller"
+	depends on CPU_SUBTYPE_SH7760
+	help
+	  This driver supports the 2 I2C interfaces on the Renesas SH7760.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-sh7760.
+
+config I2C_SH_MOBILE
+	tristate "SuperH Mobile I2C Controller"
+	depends on SUPERH
+	help
+	  If you say yes to this option, support will be included for the
+	  built-in I2C interface on the Renesas SH-Mobile processor.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-sh_mobile.
+
+config I2C_SIMTEC
+	tristate "Simtec Generic I2C interface"
+	select I2C_ALGOBIT
+	help
+	  If you say yes to this option, support will be included for
+	  the Simtec Generic I2C interface. This driver is for the
+	  simple I2C bus used on newer Simtec products for general
+	  I2C, such as DDC on the Simtec BBD2016A.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called i2c-simtec.
+
+config I2C_VERSATILE
+	tristate "ARM Versatile/Realview I2C bus support"
+	depends on ARCH_VERSATILE || ARCH_REALVIEW
+	select I2C_ALGOBIT
+	help
+	  Say yes if you want to support the I2C serial bus on ARMs Versatile
+	  range of platforms.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-versatile.
+
+comment "External I2C/SMBus adapter drivers"
+
 config I2C_PARPORT
 	tristate "Parallel port adapter"
 	depends on PARPORT
@@ -375,118 +517,6 @@ config I2C_PARPORT_LIGHT
 	  This support is also available as a module.  If so, the module
 	  will be called i2c-parport-light.
 
-config I2C_PASEMI
-	tristate "PA Semi SMBus interface"
-	depends on PPC_PASEMI && PCI
-	help
-	  Supports the PA Semi PWRficient on-chip SMBus interfaces.
-
-config I2C_S3C2410
-	tristate "S3C2410 I2C Driver"
-	depends on ARCH_S3C2410
-	help
-	  Say Y here to include support for I2C controller in the
-	  Samsung S3C2410 based System-on-Chip devices.
-
-config I2C_SIBYTE
-	tristate "SiByte SMBus interface"
-	depends on SIBYTE_SB1xxx_SOC
-	help
-	  Supports the SiByte SOC on-chip I2C interfaces (2 channels).
-
-config I2C_SIMTEC
-	tristate "Simtec Generic I2C interface"
-	select I2C_ALGOBIT
-	help
-	  If you say yes to this option, support will be included for
-	  the Simtec Generic I2C interface. This driver is for the
-	  simple I2C bus used on newer Simtec products for general
-	  I2C, such as DDC on the Simtec BBD2016A.
-
-	  This driver can also be built as a module. If so, the module
-	  will be called i2c-simtec.
-
-config SCx200_I2C
-	tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)"
-	depends on SCx200_GPIO
-	select I2C_ALGOBIT
-	help
-	  Enable the use of two GPIO pins of a SCx200 processor as an I2C bus.
-
-	  If you don't know what to do here, say N.
-
-	  This support is also available as a module.  If so, the module
-	  will be called scx200_i2c.
-
-	  This driver is deprecated and will be dropped soon. Use i2c-gpio
-	  (or scx200_acb) instead.
-
-config SCx200_I2C_SCL
-	int "GPIO pin used for SCL"
-	depends on SCx200_I2C
-	default "12"
-	help
-	  Enter the GPIO pin number used for the SCL signal.  This value can
-	  also be specified with a module parameter.
-
-config SCx200_I2C_SDA
-	int "GPIO pin used for SDA"
-	depends on SCx200_I2C
-	default "13"
-	help
-	  Enter the GPIO pin number used for the SSA signal.  This value can
-	  also be specified with a module parameter.
-
-config SCx200_ACB
-	tristate "Geode ACCESS.bus support"
-	depends on X86_32 && PCI
-	help
-	  Enable the use of the ACCESS.bus controllers on the Geode SCx200 and
-	  SC1100 processors and the CS5535 and CS5536 Geode companion devices.
-
-	  If you don't know what to do here, say N.
-
-	  This support is also available as a module.  If so, the module
-	  will be called scx200_acb.
-
-config I2C_SIS5595
-	tristate "SiS 5595"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the
-	  SiS5595 SMBus (a subset of I2C) interface.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-sis5595.
-
-config I2C_SIS630
-	tristate "SiS 630/730"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the
-	  SiS630 and SiS730 SMBus (a subset of I2C) interface.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-sis630.
-
-config I2C_SIS96X
-	tristate "SiS 96x"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the SiS
-	  96x SMBus (a subset of I2C) interfaces.  Specifically, the following
-	  chipsets are supported:
-	    645/961
-	    645DX/961
-	    645DX/962
-	    648/961
-	    650/961
-	    735
-	    745
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-sis96x.
-
 config I2C_TAOS_EVM
 	tristate "TAOS evaluation module"
 	depends on EXPERIMENTAL
@@ -503,21 +533,8 @@ config I2C_TAOS_EVM
 	  This support is also available as a module.  If so, the module
 	  will be called i2c-taos-evm.
 
-config I2C_STUB
-	tristate "I2C/SMBus Test Stub"
-	depends on EXPERIMENTAL && m
-	default 'n'
-	help
-	  This module may be useful to developers of SMBus client drivers,
-	  especially for certain kinds of sensor chips.
-
-	  If you do build this module, be sure to read the notes and warnings
-	  in <file:Documentation/i2c/i2c-stub>.
-
-	  If you don't know what to do here, definitely say N.
-
 config I2C_TINY_USB
-	tristate "I2C-Tiny-USB"
+	tristate "Tiny-USB adapter"
 	depends on USB
 	help
 	  If you say yes to this option, support will be included for the
@@ -527,16 +544,21 @@ config I2C_TINY_USB
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-tiny-usb.
 
-config I2C_VERSATILE
-	tristate "ARM Versatile/Realview I2C bus support"
-	depends on ARCH_VERSATILE || ARCH_REALVIEW
+comment "Graphics adapter I2C/DDC channel drivers"
+	depends on PCI
+
+config I2C_VOODOO3
+	tristate "Voodoo 3"
+	depends on PCI
 	select I2C_ALGOBIT
 	help
-	  Say yes if you want to support the I2C serial bus on ARMs Versatile
-	  range of platforms.
+	  If you say yes to this option, support will be included for the
+	  Voodoo 3 I2C interface.
 
 	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-versatile.
+	  will be called i2c-voodoo3.
+
+comment "Other I2C/SMBus bus drivers"
 
 config I2C_ACORN
 	tristate "Acorn IOC/IOMD I2C bus support"
@@ -548,46 +570,16 @@ config I2C_ACORN
 
 	  If you don't know, say Y.
 
-config I2C_VIA
-	tristate "VIA 82C586B"
-	depends on PCI && EXPERIMENTAL
-	select I2C_ALGOBIT
-	help
-	  If you say yes to this option, support will be included for the VIA
-          82C586B I2C interface
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-via.
-
-config I2C_VIAPRO
-	tristate "VIA VT82C596/82C686/82xx and CX700"
-	depends on PCI
-	help
-	  If you say yes to this option, support will be included for the VIA
-	  VT82C596 and later SMBus interface.  Specifically, the following
-	  chipsets are supported:
-	    VT82C596A/B
-	    VT82C686A/B
-	    VT8231
-	    VT8233/A
-	    VT8235
-	    VT8237R/A/S
-	    VT8251
-	    CX700
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-viapro.
-
-config I2C_VOODOO3
-	tristate "Voodoo 3"
-	depends on PCI
-	select I2C_ALGOBIT
+config I2C_ELEKTOR
+	tristate "Elektor ISA card"
+	depends on ISA && BROKEN_ON_SMP
+	select I2C_ALGOPCF
 	help
-	  If you say yes to this option, support will be included for the
-	  Voodoo 3 I2C interface.
+	  This supports the PCF8584 ISA bus I2C adapter.  Say Y if you own
+	  such an adapter.
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-voodoo3.
+	  This support is also available as a module.  If so, the module
+	  will be called i2c-elektor.
 
 config I2C_PCA_ISA
 	tristate "PCA9564 on an ISA bus"
@@ -617,26 +609,6 @@ config I2C_PCA_PLATFORM
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-pca-platform.
 
-config I2C_MV64XXX
-	tristate "Marvell mv64xxx I2C Controller"
-	depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL
-	help
-	  If you say yes to this option, support will be included for the
-	  built-in I2C interface on the Marvell 64xxx line of host bridges.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-mv64xxx.
-
-config I2C_PNX
-	tristate "I2C bus support for Philips PNX targets"
-	depends on ARCH_PNX4008
-	help
-	  This driver supports the Philips IP3204 I2C IP block master and/or
-	  slave controller
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-pnx.
-
 config I2C_PMCMSP
 	tristate "PMC MSP I2C TWI Controller"
 	depends on PMC_MSP
@@ -646,23 +618,66 @@ config I2C_PMCMSP
 	  This driver can also be built as module. If so, the module
 	  will be called i2c-pmcmsp.
 
-config I2C_SH7760
-	tristate "Renesas SH7760 I2C Controller"
-	depends on CPU_SUBTYPE_SH7760
+config I2C_SIBYTE
+	tristate "SiByte SMBus interface"
+	depends on SIBYTE_SB1xxx_SOC
 	help
-	  This driver supports the 2 I2C interfaces on the Renesas SH7760.
+	  Supports the SiByte SOC on-chip I2C interfaces (2 channels).
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-sh7760.
+config I2C_STUB
+	tristate "I2C/SMBus Test Stub"
+	depends on EXPERIMENTAL && m
+	default 'n'
+	help
+	  This module may be useful to developers of SMBus client drivers,
+	  especially for certain kinds of sensor chips.
 
-config I2C_SH_MOBILE
-	tristate "SuperH Mobile I2C Controller"
-	depends on SUPERH
+	  If you do build this module, be sure to read the notes and warnings
+	  in <file:Documentation/i2c/i2c-stub>.
+
+	  If you don't know what to do here, definitely say N.
+
+config SCx200_I2C
+	tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)"
+	depends on SCx200_GPIO
+	select I2C_ALGOBIT
 	help
-	  If you say yes to this option, support will be included for the
-	  built-in I2C interface on the Renesas SH-Mobile processor.
+	  Enable the use of two GPIO pins of a SCx200 processor as an I2C bus.
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-sh_mobile.
+	  If you don't know what to do here, say N.
+
+	  This support is also available as a module.  If so, the module
+	  will be called scx200_i2c.
+
+	  This driver is deprecated and will be dropped soon. Use i2c-gpio
+	  (or scx200_acb) instead.
+
+config SCx200_I2C_SCL
+	int "GPIO pin used for SCL"
+	depends on SCx200_I2C
+	default "12"
+	help
+	  Enter the GPIO pin number used for the SCL signal.  This value can
+	  also be specified with a module parameter.
+
+config SCx200_I2C_SDA
+	int "GPIO pin used for SDA"
+	depends on SCx200_I2C
+	default "13"
+	help
+	  Enter the GPIO pin number used for the SSA signal.  This value can
+	  also be specified with a module parameter.
+
+config SCx200_ACB
+	tristate "Geode ACCESS.bus support"
+	depends on X86_32 && PCI
+	help
+	  Enable the use of the ACCESS.bus controllers on the Geode SCx200 and
+	  SC1100 processors and the CS5535 and CS5536 Geode companion devices.
+
+	  If you don't know what to do here, say N.
+
+	  This support is also available as a module.  If so, the module
+	  will be called scx200_acb.
 
 endmenu
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 81bb407d24c..48a6a5bddc5 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -2,55 +2,66 @@
 # Makefile for the i2c bus drivers.
 #
 
+# PC SMBus host controller drivers
 obj-$(CONFIG_I2C_ALI1535)	+= i2c-ali1535.o
 obj-$(CONFIG_I2C_ALI1563)	+= i2c-ali1563.o
 obj-$(CONFIG_I2C_ALI15X3)	+= i2c-ali15x3.o
 obj-$(CONFIG_I2C_AMD756)	+= i2c-amd756.o
 obj-$(CONFIG_I2C_AMD756_S4882)	+= i2c-amd756-s4882.o
 obj-$(CONFIG_I2C_AMD8111)	+= i2c-amd8111.o
+obj-$(CONFIG_I2C_I801)		+= i2c-i801.o
+obj-$(CONFIG_I2C_NFORCE2)	+= i2c-nforce2.o
+obj-$(CONFIG_I2C_NFORCE2_S4985)	+= i2c-nforce2-s4985.o
+obj-$(CONFIG_I2C_PIIX4)		+= i2c-piix4.o
+obj-$(CONFIG_I2C_SIS5595)	+= i2c-sis5595.o
+obj-$(CONFIG_I2C_SIS630)	+= i2c-sis630.o
+obj-$(CONFIG_I2C_SIS96X)	+= i2c-sis96x.o
+obj-$(CONFIG_I2C_VIA)		+= i2c-via.o
+obj-$(CONFIG_I2C_VIAPRO)	+= i2c-viapro.o
+
+# Mac SMBus host controller drivers
+obj-$(CONFIG_I2C_HYDRA)		+= i2c-hydra.o
+obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
+
+# Embebbed system I2C/SMBus host controller drivers
 obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
-obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
-obj-$(CONFIG_I2C_HYDRA)		+= i2c-hydra.o
-obj-$(CONFIG_I2C_I801)		+= i2c-i801.o
 obj-$(CONFIG_I2C_IBM_IIC)	+= i2c-ibm_iic.o
 obj-$(CONFIG_I2C_IOP3XX)	+= i2c-iop3xx.o
 obj-$(CONFIG_I2C_IXP2000)	+= i2c-ixp2000.o
-obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 obj-$(CONFIG_I2C_MPC)		+= i2c-mpc.o
 obj-$(CONFIG_I2C_MV64XXX)	+= i2c-mv64xxx.o
-obj-$(CONFIG_I2C_NFORCE2)	+= i2c-nforce2.o
-obj-$(CONFIG_I2C_NFORCE2_S4985)	+= i2c-nforce2-s4985.o
 obj-$(CONFIG_I2C_OCORES)	+= i2c-ocores.o
 obj-$(CONFIG_I2C_OMAP)		+= i2c-omap.o
-obj-$(CONFIG_I2C_PARPORT)	+= i2c-parport.o
-obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_PASEMI)	+= i2c-pasemi.o
-obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
-obj-$(CONFIG_I2C_PCA_PLATFORM)	+= i2c-pca-platform.o
-obj-$(CONFIG_I2C_PIIX4)		+= i2c-piix4.o
-obj-$(CONFIG_I2C_PMCMSP)	+= i2c-pmcmsp.o
 obj-$(CONFIG_I2C_PNX)		+= i2c-pnx.o
 obj-$(CONFIG_I2C_PXA)		+= i2c-pxa.o
 obj-$(CONFIG_I2C_S3C2410)	+= i2c-s3c2410.o
 obj-$(CONFIG_I2C_SH7760)	+= i2c-sh7760.o
 obj-$(CONFIG_I2C_SH_MOBILE)	+= i2c-sh_mobile.o
-obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
 obj-$(CONFIG_I2C_SIMTEC)	+= i2c-simtec.o
-obj-$(CONFIG_I2C_SIS5595)	+= i2c-sis5595.o
-obj-$(CONFIG_I2C_SIS630)	+= i2c-sis630.o
-obj-$(CONFIG_I2C_SIS96X)	+= i2c-sis96x.o
-obj-$(CONFIG_I2C_STUB)		+= i2c-stub.o
+obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
+
+# External I2C/SMBus adapter drivers
+obj-$(CONFIG_I2C_PARPORT)	+= i2c-parport.o
+obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_TAOS_EVM)	+= i2c-taos-evm.o
 obj-$(CONFIG_I2C_TINY_USB)	+= i2c-tiny-usb.o
-obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
-obj-$(CONFIG_I2C_ACORN)		+= i2c-acorn.o
-obj-$(CONFIG_I2C_VIA)		+= i2c-via.o
-obj-$(CONFIG_I2C_VIAPRO)	+= i2c-viapro.o
+
+# Graphics adapter I2C/DDC channel drivers
 obj-$(CONFIG_I2C_VOODOO3)	+= i2c-voodoo3.o
+
+# Other I2C/SMBus bus drivers
+obj-$(CONFIG_I2C_ACORN)		+= i2c-acorn.o
+obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
+obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
+obj-$(CONFIG_I2C_PCA_PLATFORM)	+= i2c-pca-platform.o
+obj-$(CONFIG_I2C_PMCMSP)	+= i2c-pmcmsp.o
+obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
+obj-$(CONFIG_I2C_STUB)		+= i2c-stub.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
 obj-$(CONFIG_SCx200_I2C)	+= scx200_i2c.o