ide-{floppy,tape}: remove debug code for dumping identify data

IDE core supports dumping raw identify data in hdparm friendly format now
so verbose identify dumping in ide-{floppy,tape}.c device drivers (done iff
IDE{FLOPPY,TAPE}_DEBUG_INFO is defined to '1' and it is '0' by default)
is no longer nedeed.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 0 insertions, 50 deletions

diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index ff8232ef965..cf48b4a46d6 100644
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -1658,7 +1658,6 @@ static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
 {
 	struct idefloppy_id_gcw gcw;
 #if IDEFLOPPY_DEBUG_INFO
-	u16 mask,i;
 	char buffer[80];
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
@@ -1705,55 +1704,6 @@ static int idefloppy_identify_device (ide_drive_t *drive,struct hd_driveid *id)
 		default: sprintf(buffer, "Reserved");break;
 	}
 	printk(KERN_INFO "Command Packet Size: %s\n", buffer);
-	printk(KERN_INFO "Model: %.40s\n",id->model);
-	printk(KERN_INFO "Firmware Revision: %.8s\n",id->fw_rev);
-	printk(KERN_INFO "Serial Number: %.20s\n",id->serial_no);
-	printk(KERN_INFO "Write buffer size(?): %d bytes\n",id->buf_size*512);
-	printk(KERN_INFO "DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
-	printk(KERN_INFO "LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
-	printk(KERN_INFO "IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
-	printk(KERN_INFO "IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
-	printk(KERN_INFO "ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
-	printk(KERN_INFO "PIO Cycle Timing Category: %d\n",id->tPIO);
-	printk(KERN_INFO "DMA Cycle Timing Category: %d\n",id->tDMA);
-	printk(KERN_INFO "Single Word DMA supported modes:\n");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_1word & mask)
-			printk(KERN_INFO "   Mode %d%s\n", i,
-			(id->dma_1word & (mask << 8)) ? " (active)" : "");
-	}
-	printk(KERN_INFO "Multi Word DMA supported modes:\n");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_mword & mask)
-			printk(KERN_INFO "   Mode %d%s\n", i,
-			(id->dma_mword & (mask << 8)) ? " (active)" : "");
-	}
-	if (id->field_valid & 0x0002) {
-		printk(KERN_INFO "Enhanced PIO Modes: %s\n",
-			id->eide_pio_modes & 1 ? "Mode 3":"None");
-		if (id->eide_dma_min == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_dma_min);
-		printk(KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n", buffer);
-		if (id->eide_dma_time == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_dma_time);
-		printk(KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n", buffer);
-		if (id->eide_pio == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_pio);
-		printk(KERN_INFO "Minimum PIO cycle without IORDY: %s\n",
-			buffer);
-		if (id->eide_pio_iordy == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_pio_iordy);
-		printk(KERN_INFO "Minimum PIO cycle with IORDY: %s\n", buffer);
-	} else
-		printk(KERN_INFO "According to the device, fields 64-70 are not valid.\n");
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
 	if (gcw.protocol != 2)