Merge branch 'master' of /home/cbou/linux-2.6

Conflicts:

	drivers/power/Kconfig
	drivers/power/Makefile

1 files changed, 9 insertions, 32 deletions

diff --git a/drivers/ide/legacy/ht6560b.c b/drivers/ide/legacy/ht6560b.c
index 4fe516df9f7..98f7c95e39e 100644
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -3,34 +3,12 @@
  */
 
 /*
- *
- *  Version 0.01        Initial version hacked out of ide.c
- *
- *  Version 0.02        Added support for PIO modes, auto-tune
- *
- *  Version 0.03        Some cleanups
- *
- *  Version 0.05        PIO mode cycle timings auto-tune using bus-speed
- *
- *  Version 0.06        Prefetch mode now defaults no OFF. To set
- *                      prefetch mode OFF/ON use "hdparm -p8/-p9".
- *                      Unmask irq is disabled when prefetch mode
- *                      is enabled.
- *
- *  Version 0.07        Trying to fix CD-ROM detection problem.
- *                      "Prefetch" mode bit OFF for ide disks and
- *                      ON for anything else.
- *
- *  Version 0.08        Need to force prefetch for CDs and other non-disk
- *                      devices. (not sure which devices exactly need
- *                      prefetch)
- *
  *  HT-6560B EIDE-controller support
  *  To activate controller support use kernel parameter "ide0=ht6560b".
  *  Use hdparm utility to enable PIO mode support.
  *
  *  Author:    Mikko Ala-Fossi            <maf@iki.fi>
- *             Jan Evert van Grootheest   <janevert@caiway.nl>
+ *             Jan Evert van Grootheest   <j.e.van.grootheest@caiway.nl>
  *
  *  Try:  http://www.maf.iki.fi/~maf/ht6560b/
  */
@@ -212,10 +190,11 @@ static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
 {
 	int active_time, recovery_time;
 	int active_cycles, recovery_cycles;
-	int bus_speed = ide_vlb_clk ? ide_vlb_clk : system_bus_clock();
+	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
 
         if (pio) {
 		unsigned int cycle_time;
+		struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 
 		cycle_time = ide_pio_cycle_time(drive, pio);
 
@@ -224,10 +203,8 @@ static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
 		 *  actual cycle time for recovery and activity
 		 *  according system bus speed.
 		 */
-		active_time = ide_pio_timings[pio].active_time;
-		recovery_time = cycle_time
-			- active_time
-			- ide_pio_timings[pio].setup_time;
+		active_time = t->active;
+		recovery_time = cycle_time - active_time - t->setup;
 		/*
 		 *  Cycle times should be Vesa bus cycles
 		 */
@@ -311,16 +288,16 @@ static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
 #endif
 }
 
-static void __init ht6560b_port_init_devs(ide_hwif_t *hwif)
+static void __init ht6560b_init_dev(ide_drive_t *drive)
 {
+	ide_hwif_t *hwif = drive->hwif;
 	/* Setting default configurations for drives. */
 	int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
 
 	if (hwif->channel)
 		t |= (HT_SECONDARY_IF << 8);
 
-	hwif->drives[0].drive_data = t;
-	hwif->drives[1].drive_data = t;
+	drive->drive_data = t;
 }
 
 static int probe_ht6560b;
@@ -329,7 +306,7 @@ module_param_named(probe, probe_ht6560b, bool, 0);
 MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
 
 static const struct ide_port_ops ht6560b_port_ops = {
-	.port_init_devs		= ht6560b_port_init_devs,
+	.init_dev		= ht6560b_init_dev,
 	.set_pio_mode		= ht6560b_set_pio_mode,
 	.selectproc		= ht6560b_selectproc,
 };