Merge branch 'linus' into x86/threadinfo

26 files changed, 201 insertions, 449 deletions

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index f702f9152ce..8e07de23d22 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1,8 +1,6 @@
 #
 # IDE ATA ATAPI Block device driver configuration
 #
-# Andre Hedrick <andre@linux-ide.org>
-#
 
 # Select HAVE_IDE if IDE is supported
 config HAVE_IDE
@@ -335,7 +333,7 @@ config BLK_DEV_CMD640
 	  This driver will work automatically in PCI based systems (most new
 	  systems have PCI slots). But if your system uses VESA local bus
 	  (VLB) instead of PCI, you must also supply a kernel boot parameter
-	  to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man
+	  to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
 	  bootparam" or see the documentation of your boot loader about how to
 	  pass options to the kernel.)
 
@@ -457,27 +455,11 @@ config BLK_DEV_ALI15X3
 	  onboard chipsets.  It also tests for Simplex mode and enables
 	  normal dual channel support.
 
-	  If you say Y here, you also need to say Y to "Use DMA by default
-	  when available", above.  Please read the comments at the top of
+	  Please read the comments at the top of
 	  <file:drivers/ide/pci/alim15x3.c>.
 
 	  If unsure, say N.
 
-config WDC_ALI15X3
-	bool "ALI M15x3 WDC support (DANGEROUS)"
-	depends on BLK_DEV_ALI15X3
-	---help---
-	  This allows for UltraDMA support for WDC drives that ignore CRC
-	  checking. You are a fool for enabling this option, but there have
-	  been requests. DO NOT COMPLAIN IF YOUR DRIVE HAS FS CORRUPTION, IF
-	  YOU ENABLE THIS! No one will listen, just laugh for ignoring this
-	  SERIOUS WARNING.
-
-	  Using this option can allow WDC drives to run at ATA-4/5 transfer
-	  rates with only an ATA-2 support structure.
-
-	  SAY N!
-
 config BLK_DEV_AMD74XX
 	tristate "AMD and nVidia IDE support"
 	depends on !ARM
@@ -520,9 +502,6 @@ config BLK_DEV_CY82C693
 	  This driver adds detection and support for the CY82C693 chipset
 	  used on Digital's PC-Alpha 164SX boards.
 
-	  If you say Y here, you need to say Y to "Use DMA by default
-	  when available" as well.
-
 config BLK_DEV_CS5520
 	tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
 	depends on EXPERIMENTAL
@@ -613,13 +592,12 @@ config BLK_DEV_SC1200
 	  National SCx200 series of embedded x86 "Geode" systems.
 
 config BLK_DEV_PIIX
-	tristate "Intel PIIXn chipsets support"
+	tristate "Intel PIIX/ICH chipsets support"
 	select BLK_DEV_IDEDMA_PCI
 	help
-	  This driver adds explicit support for Intel PIIX and ICH chips
-	  and also for the Efar Victory66 (slc90e66) chip.  This allows
-	  the kernel to change PIO, DMA and UDMA speeds and to configure
-	  the chip to optimum performance.
+	  This driver adds explicit support for Intel PIIX and ICH chips.
+	  This allows the kernel to change PIO, DMA and UDMA speeds and to
+	  configure the chip to optimum performance.
 
 config BLK_DEV_IT8213
 	tristate "IT8213 IDE support"
@@ -657,11 +635,7 @@ config BLK_DEV_PDC202XX_OLD
 	  happen if the BIOS revisions of all installed cards (three-max) do
 	  not match, the driver attempts to do dynamic tuning of the chipset
 	  at boot-time for max-speed.  Ultra33 BIOS 1.25 or newer is required
-	  for more than one card. This card may require that you say Y to
-	  "Special UDMA Feature".
-
-	  If you say Y here, you need to say Y to "Use DMA by default when
-	  available" as well.
+	  for more than one card.
 
 	  Please read the comments at the top of
 	  <file:drivers/ide/pci/pdc202xx_old.c>.
@@ -710,9 +684,6 @@ config BLK_DEV_SIS5513
 	  ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
 	  SiS745, SiS750
 
-	  If you say Y here, you need to say Y to "Use DMA by default when
-	  available" as well.
-
 	  Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
 
 config BLK_DEV_SL82C105
@@ -734,9 +705,6 @@ config BLK_DEV_SLC90E66
 	  and it will handle timing cycles.  Since this is an improved
 	  look-a-like to the PIIX4 it should be a nice addition.
 
-	  If you say Y here, you need to say Y to "Use DMA by default when
-	  available" as well.
-
 	  Please read the comments at the top of
 	  <file:drivers/ide/pci/slc90e66.c>.
 
@@ -855,13 +823,6 @@ config BLK_DEV_IDE_RAPIDE
 	  Say Y here if you want to support the Yellowstone RapIDE controller
 	  manufactured for use with Acorn computers.
 
-config BLK_DEV_IDE_BAST
-	tristate "Simtec BAST / Thorcom VR1000 IDE support"
-	depends on ARM && (ARCH_BAST || MACH_VR1000)
-	help
-	  Say Y here if you want to support the onboard IDE channels on the
-	  Simtec BAST or the Thorcom VR1000
-
 config IDE_H8300
 	tristate "H8300 IDE support"
 	depends on H8300
@@ -888,17 +849,17 @@ config BLK_DEV_IDEDOUBLER
 	bool "Amiga IDE Doubler support (EXPERIMENTAL)"
 	depends on BLK_DEV_GAYLE && EXPERIMENTAL
 	---help---
-	  This driver provides support for the so-called `IDE doublers' (made
+	  This feature provides support for the so-called `IDE doublers' (made
 	  by various manufacturers, e.g. Eyetech) that can be connected to
 	  the on-board IDE interface of some Amiga models. Using such an IDE
 	  doubler, you can connect up to four instead of two IDE devices to
 	  the Amiga's on-board IDE interface.
 
 	  Note that the normal Amiga Gayle IDE driver may not work correctly
-	  if you have an IDE doubler and don't enable this driver!
+	  if you have an IDE doubler and don't enable this feature!
 
-	  Say Y if you have an IDE doubler.  The driver is enabled at kernel
-	  runtime using the "ide=doubler" kernel boot parameter.
+	  Say Y if you have an IDE doubler.  The feature is enabled at kernel
+	  runtime using the "gayle.doubler" kernel boot parameter.
 
 config BLK_DEV_BUDDHA
 	tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
@@ -1060,6 +1021,7 @@ endif
 
 config BLK_DEV_HD_ONLY
 	bool "Old hard disk (MFM/RLL/IDE) driver"
+	depends on !ARM || ARCH_RPC || ARCH_SHARK || BROKEN
 	help
 	  There are two drivers for MFM/RLL/IDE hard disks. Most people use
 	  the newer enhanced driver, but this old one is still around for two
diff --git a/drivers/ide/arm/Makefile b/drivers/ide/arm/Makefile
index 936e7b0237f..5bc26053afa 100644
--- a/drivers/ide/arm/Makefile
+++ b/drivers/ide/arm/Makefile
@@ -1,7 +1,6 @@
 
 obj-$(CONFIG_BLK_DEV_IDE_ICSIDE)	+= icside.o
 obj-$(CONFIG_BLK_DEV_IDE_RAPIDE)	+= rapide.o
-obj-$(CONFIG_BLK_DEV_IDE_BAST)		+= bast-ide.o
 obj-$(CONFIG_BLK_DEV_PALMCHIP_BK3710)	+= palm_bk3710.o
 
 ifeq ($(CONFIG_IDE_ARM), m)
diff --git a/drivers/ide/arm/bast-ide.c b/drivers/ide/arm/bast-ide.c
deleted file mode 100644
index 713cef20622..00000000000
--- a/drivers/ide/arm/bast-ide.c
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * Copyright (c) 2003-2004 Simtec Electronics
- *  Ben Dooks <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/mach-types.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/arch/map.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-irq.h>
-
-#define DRV_NAME "bast-ide"
-
-static int __init bastide_register(unsigned int base, unsigned int aux, int irq)
-{
-	ide_hwif_t *hwif;
-	hw_regs_t hw;
-	int i;
-	u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
-
-	memset(&hw, 0, sizeof(hw));
-
-	base += BAST_IDE_CS;
-	aux  += BAST_IDE_CS;
-
-	for (i = 0; i <= 7; i++) {
-		hw.io_ports_array[i] = (unsigned long)base;
-		base += 0x20;
-	}
-
-	hw.io_ports.ctl_addr = aux + (6 * 0x20);
-	hw.irq = irq;
-
-	hwif = ide_find_port();
-	if (hwif == NULL)
-		goto out;
-
-	i = hwif->index;
-
-	ide_init_port_data(hwif, i);
-	ide_init_port_hw(hwif, &hw);
-	hwif->port_ops = NULL;
-
-	idx[0] = i;
-
-	ide_device_add(idx, NULL);
-out:
-	return 0;
-}
-
-static int __init bastide_init(void)
-{
-	unsigned long base = BAST_VA_IDEPRI + BAST_IDE_CS;
-
-	/* we can treat the VR1000 and the BAST the same */
-
-	if (!(machine_is_bast() || machine_is_vr1000()))
-		return 0;
-
-	printk("BAST: IDE driver, (c) 2003-2004 Simtec Electronics\n");
-
-	if (!request_mem_region(base, 0x400000, DRV_NAME)) {
-		printk(KERN_ERR "%s: resources busy\n", DRV_NAME);
-		return -EBUSY;
-	}
-
-	bastide_register(BAST_VA_IDEPRI, BAST_VA_IDEPRIAUX, IRQ_IDE0);
-	bastide_register(BAST_VA_IDESEC, BAST_VA_IDESECAUX, IRQ_IDE1);
-
-	return 0;
-}
-
-module_init(bastide_init);
-
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Simtec BAST / Thorcom VR1000 IDE driver");
diff --git a/drivers/ide/arm/ide_arm.c b/drivers/ide/arm/ide_arm.c
index 4263ffd4ab2..2f311da4c96 100644
--- a/drivers/ide/arm/ide_arm.c
+++ b/drivers/ide/arm/ide_arm.c
@@ -49,6 +49,7 @@ static int __init ide_arm_init(void)
 	memset(&hw, 0, sizeof(hw));
 	ide_std_init_ports(&hw, base, ctl);
 	hw.irq = IDE_ARM_IRQ;
+	hw.chipset = ide_generic;
 
 	hwif = ide_find_port();
 	if (hwif) {
diff --git a/drivers/ide/arm/palm_bk3710.c b/drivers/ide/arm/palm_bk3710.c
index 96378ebfb31..cc24803fadf 100644
--- a/drivers/ide/arm/palm_bk3710.c
+++ b/drivers/ide/arm/palm_bk3710.c
@@ -353,8 +353,8 @@ static int __devinit palm_bk3710_probe(struct platform_device *pdev)
 	struct clk *clkp;
 	struct resource *mem, *irq;
 	ide_hwif_t *hwif;
-	void __iomem *base;
-	int pribase, i;
+	unsigned long base;
+	int i;
 	hw_regs_t hw;
 	u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
 
@@ -374,22 +374,27 @@ static int __devinit palm_bk3710_probe(struct platform_device *pdev)
 		printk(KERN_ERR "failed to get memory region resource\n");
 		return -ENODEV;
 	}
+
 	irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (irq == NULL) {
 		printk(KERN_ERR "failed to get IRQ resource\n");
 		return -ENODEV;
 	}
 
-	base = (void *)mem->start;
+	if (request_mem_region(mem->start, mem->end - mem->start + 1,
+			       "palm_bk3710") == NULL) {
+		printk(KERN_ERR "failed to request memory region\n");
+		return -EBUSY;
+	}
+
+	base = IO_ADDRESS(mem->start);
 
 	/* Configure the Palm Chip controller */
-	palm_bk3710_chipinit(base);
+	palm_bk3710_chipinit((void __iomem *)base);
 
-	pribase = mem->start + IDE_PALM_ATA_PRI_REG_OFFSET;
 	for (i = 0; i < IDE_NR_PORTS - 2; i++)
-		hw.io_ports_array[i] = pribase + i;
-	hw.io_ports.ctl_addr = mem->start +
-			IDE_PALM_ATA_PRI_CTL_OFFSET;
+		hw.io_ports_array[i] = base + IDE_PALM_ATA_PRI_REG_OFFSET + i;
+	hw.io_ports.ctl_addr = base + IDE_PALM_ATA_PRI_CTL_OFFSET;
 	hw.irq = irq->start;
 	hw.chipset = ide_palm3710;
 
@@ -409,9 +414,6 @@ static int __devinit palm_bk3710_probe(struct platform_device *pdev)
 
 	ide_device_add(idx, &palm_bk3710_port_info);
 
-	if (!hwif->present)
-		goto out;
-
 	return 0;
 out:
 	printk(KERN_WARNING "Palm Chip BK3710 IDE Register Fail\n");
@@ -437,4 +439,3 @@ static int __init palm_bk3710_init(void)
 
 module_init(palm_bk3710_init);
 MODULE_LICENSE("GPL");
-
diff --git a/drivers/ide/ide-generic.c b/drivers/ide/ide-generic.c
index a6073e248f4..2d92214096a 100644
--- a/drivers/ide/ide-generic.c
+++ b/drivers/ide/ide-generic.c
@@ -22,6 +22,10 @@
 
 #define DRV_NAME	"ide_generic"
 
+static int probe_mask = 0x03;
+module_param(probe_mask, int, 0);
+MODULE_PARM_DESC(probe_mask, "probe mask for legacy ISA IDE ports");
+
 static ssize_t store_add(struct class *cls, const char *buf, size_t n)
 {
 	ide_hwif_t *hwif;
@@ -89,6 +93,9 @@ static int __init ide_generic_init(void)
 	u8 idx[MAX_HWIFS];
 	int i;
 
+	printk(KERN_INFO DRV_NAME ": please use \"probe_mask=0x3f\" module "
+			 "parameter for probing all legacy ISA IDE ports\n");
+
 	for (i = 0; i < MAX_HWIFS; i++) {
 		ide_hwif_t *hwif;
 		unsigned long io_addr = ide_default_io_base(i);
@@ -96,7 +103,7 @@ static int __init ide_generic_init(void)
 
 		idx[i] = 0xff;
 
-		if (io_addr) {
+		if ((probe_mask & (1 << i)) && io_addr) {
 			if (!request_region(io_addr, 8, DRV_NAME)) {
 				printk(KERN_ERR "%s: I/O resource 0x%lX-0x%lX "
 						"not free.\n",
@@ -125,6 +132,7 @@ static int __init ide_generic_init(void)
 			memset(&hw, 0, sizeof(hw));
 			ide_std_init_ports(&hw, io_addr, io_addr + 0x206);
 			hw.irq = ide_default_irq(io_addr);
+			hw.chipset = ide_generic;
 			ide_init_port_hw(hwif, &hw);
 
 			idx[i] = i;
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 57d9a9a79a6..0daf923541f 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -95,7 +95,7 @@ void SELECT_DRIVE (ide_drive_t *drive)
 	hwif->OUTB(drive->select.all, hwif->io_ports.device_addr);
 }
 
-void SELECT_MASK (ide_drive_t *drive, int mask)
+static void SELECT_MASK(ide_drive_t *drive, int mask)
 {
 	const struct ide_port_ops *port_ops = drive->hwif->port_ops;
 
diff --git a/drivers/ide/ide-pnp.c b/drivers/ide/ide-pnp.c
index 6a8953f68e9..adbd0178416 100644
--- a/drivers/ide/ide-pnp.c
+++ b/drivers/ide/ide-pnp.c
@@ -55,6 +55,7 @@ static int idepnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 	memset(&hw, 0, sizeof(hw));
 	ide_std_init_ports(&hw, base, ctl);
 	hw.irq = pnp_irq(dev, 0);
+	hw.chipset = ide_generic;
 
 	hwif = ide_find_port();
 	if (hwif) {
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 34b0d4f26b5..380fa0c8cc8 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -648,13 +648,12 @@ static int ide_register_port(ide_hwif_t *hwif)
 
 	get_device(&hwif->gendev);
 
-	hwif->portdev = device_create(ide_port_class, &hwif->gendev,
-				      MKDEV(0, 0), hwif->name);
+	hwif->portdev = device_create_drvdata(ide_port_class, &hwif->gendev,
+					      MKDEV(0, 0), hwif, hwif->name);
 	if (IS_ERR(hwif->portdev)) {
 		ret = PTR_ERR(hwif->portdev);
 		device_unregister(&hwif->gendev);
 	}
-	dev_set_drvdata(hwif->portdev, hwif);
 out:
 	return ret;
 }
@@ -1334,8 +1333,7 @@ static void ide_port_init_devices(ide_hwif_t *hwif)
 static void ide_init_port(ide_hwif_t *hwif, unsigned int port,
 			  const struct ide_port_info *d)
 {
-	if (d->chipset != ide_etrax100)
-		hwif->channel = port;
+	hwif->channel = port;
 
 	if (d->chipset)
 		hwif->chipset = d->chipset;
@@ -1520,7 +1518,7 @@ int ide_device_add_all(u8 *idx, const struct ide_port_info *d)
 			continue;
 		}
 
-		if (d->chipset != ide_etrax100 && (i & 1) && mate) {
+		if ((i & 1) && mate) {
 			hwif->mate = mate;
 			mate->mate = hwif;
 		}
@@ -1666,6 +1664,7 @@ static void ide_legacy_init_one(u8 *idx, hw_regs_t *hw, u8 port_no,
 
 	ide_std_init_ports(hw, base, ctl);
 	hw->irq = irq;
+	hw->chipset = d->chipset;
 
 	hwif = ide_find_port_slot(d);
 	if (hwif) {
diff --git a/drivers/ide/ide-proc.c b/drivers/ide/ide-proc.c
index 8d6ad812a01..55ec7f79877 100644
--- a/drivers/ide/ide-proc.c
+++ b/drivers/ide/ide-proc.c
@@ -63,7 +63,6 @@ static int proc_ide_read_imodel
 	case ide_pmac:		name = "mac-io";	break;
 	case ide_au1xxx:	name = "au1xxx";	break;
 	case ide_palm3710:      name = "palm3710";      break;
-	case ide_etrax100:	name = "etrax100";	break;
 	case ide_acorn:		name = "acorn";		break;
 	default:		name = "(unknown)";	break;
 	}
diff --git a/drivers/ide/ide-taskfile.c b/drivers/ide/ide-taskfile.c
index 0c908ca3ff7..ab545ffa154 100644
--- a/drivers/ide/ide-taskfile.c
+++ b/drivers/ide/ide-taskfile.c
@@ -225,10 +225,10 @@ static u8 wait_drive_not_busy(ide_drive_t *drive)
 	u8 stat;
 
 	/*
-	 * Last sector was transfered, wait until drive is ready.
-	 * This can take up to 10 usec, but we will wait max 1 ms.
+	 * Last sector was transfered, wait until device is ready.  This can
+	 * take up to 6 ms on some ATAPI devices, so we will wait max 10 ms.
 	 */
-	for (retries = 0; retries < 100; retries++) {
+	for (retries = 0; retries < 1000; retries++) {
 		stat = ide_read_status(drive);
 
 		if (stat & BUSY_STAT)
diff --git a/drivers/ide/legacy/buddha.c b/drivers/ide/legacy/buddha.c
index 5c730e4dd73..9a1d27ef3f8 100644
--- a/drivers/ide/legacy/buddha.c
+++ b/drivers/ide/legacy/buddha.c
@@ -138,6 +138,8 @@ static void __init buddha_setup_ports(hw_regs_t *hw, unsigned long base,
 
 	hw->irq = IRQ_AMIGA_PORTS;
 	hw->ack_intr = ack_intr;
+
+	hw->chipset = ide_generic;
 }
 
     /*
diff --git a/drivers/ide/legacy/falconide.c b/drivers/ide/legacy/falconide.c
index 9e449a0c623..af11028b479 100644
--- a/drivers/ide/legacy/falconide.c
+++ b/drivers/ide/legacy/falconide.c
@@ -81,6 +81,8 @@ static void __init falconide_setup_ports(hw_regs_t *hw)
 
 	hw->irq = IRQ_MFP_IDE;
 	hw->ack_intr = NULL;
+
+	hw->chipset = ide_generic;
 }
 
     /*
diff --git a/drivers/ide/legacy/gayle.c b/drivers/ide/legacy/gayle.c
index a9c2593a898..fed7d812761 100644
--- a/drivers/ide/legacy/gayle.c
+++ b/drivers/ide/legacy/gayle.c
@@ -16,6 +16,7 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 #include <linux/zorro.h>
+#include <linux/module.h>
 
 #include <asm/setup.h>
 #include <asm/amigahw.h>
@@ -62,7 +63,10 @@
 					       GAYLE_NUM_HWIFS-1)
 #define GAYLE_HAS_CONTROL_REG	(!ide_doubler)
 #define GAYLE_IDEREG_SIZE	(ide_doubler ? 0x1000 : 0x2000)
+
 int ide_doubler = 0;	/* support IDE doublers? */
+EXPORT_SYMBOL_GPL(ide_doubler);
+
 module_param_named(doubler, ide_doubler, bool, 0);
 MODULE_PARM_DESC(doubler, "enable support for IDE doublers");
 #endif /* CONFIG_BLK_DEV_IDEDOUBLER */
@@ -112,6 +116,8 @@ static void __init gayle_setup_ports(hw_regs_t *hw, unsigned long base,
 
 	hw->irq = IRQ_AMIGA_PORTS;
 	hw->ack_intr = ack_intr;
+
+	hw->chipset = ide_generic;
 }
 
     /*
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index aa2ea3deac8..3381424d70a 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -135,13 +135,17 @@ static void ide_detach(struct pcmcia_device *link)
 {
     ide_info_t *info = link->priv;
     ide_hwif_t *hwif = info->hwif;
+    unsigned long data_addr, ctl_addr;
 
     DEBUG(0, "ide_detach(0x%p)\n", link);
 
+    data_addr = hwif->io_ports.data_addr;
+    ctl_addr  = hwif->io_ports.ctl_addr;
+
     ide_release(link);
 
-    release_region(hwif->io_ports.ctl_addr, 1);
-    release_region(hwif->io_ports.data_addr, 8);
+    release_region(ctl_addr, 1);
+    release_region(data_addr, 8);
 
     kfree(info);
 } /* ide_detach */
@@ -194,6 +198,16 @@ static ide_hwif_t *idecs_register(unsigned long io, unsigned long ctl,
     if (hwif->present)
 	return hwif;
 
+    /* retry registration in case device is still spinning up */
+    for (i = 0; i < 10; i++) {
+	msleep(100);
+	ide_port_scan(hwif);
+	if (hwif->present)
+	    return hwif;
+    }
+
+    return hwif;
+
 out_release:
     release_region(ctl, 1);
     release_region(io, 8);
@@ -222,7 +236,7 @@ static int ide_config(struct pcmcia_device *link)
 	cistpl_cftable_entry_t dflt;
     } *stk = NULL;
     cistpl_cftable_entry_t *cfg;
-    int i, pass, last_ret = 0, last_fn = 0, is_kme = 0;
+    int pass, last_ret = 0, last_fn = 0, is_kme = 0;
     unsigned long io_base, ctl_base;
     ide_hwif_t *hwif;
 
@@ -319,30 +333,15 @@ static int ide_config(struct pcmcia_device *link)
     if (is_kme)
 	outb(0x81, ctl_base+1);
 
-    /* retry registration in case device is still spinning up */
-    for (i = 0; i < 10; i++) {
-	hwif = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ, link);
-	if (hwif)
-	    break;
-	if (link->io.NumPorts1 == 0x20) {
+     hwif = idecs_register(io_base, ctl_base, link->irq.AssignedIRQ, link);
+     if (hwif == NULL && link->io.NumPorts1 == 0x20) {
 	    outb(0x02, ctl_base + 0x10);
 	    hwif = idecs_register(io_base + 0x10, ctl_base + 0x10,
 				  link->irq.AssignedIRQ, link);
-	    if (hwif) {
-		io_base += 0x10;
-		ctl_base += 0x10;
-		break;
-	    }
-	}
-	msleep(100);
     }
 
-    if (hwif == NULL) {
-	printk(KERN_NOTICE "ide-cs: ide_register() at 0x%3lx & 0x%3lx"
-	       ", irq %u failed\n", io_base, ctl_base,
-	       link->irq.AssignedIRQ);
+    if (hwif == NULL)
 	goto failed;
-    }
 
     info->ndev = 1;
     sprintf(info->node.dev_name, "hd%c", 'a' + hwif->index * 2);
@@ -411,6 +410,7 @@ static struct pcmcia_device_id ide_ids[] = {
 	PCMCIA_DEVICE_MANF_CARD(0x001c, 0x0001),	/* Mitsubishi CFA */
 	PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704),
 	PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401),	/* SanDisk CFA */
+	PCMCIA_DEVICE_MANF_CARD(0x004f, 0x0000),	/* Kingston */
 	PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000),	/* Toshiba */
 	PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
 	PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000),	/* Samsung */
@@ -440,6 +440,7 @@ static struct pcmcia_device_id ide_ids[] = {
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDE", 0x547e66dc, 0x5c5ab149),
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDEII", 0x547e66dc, 0xb3662674),
 	PCMCIA_DEVICE_PROD_ID12("LOOKMEET", "CBIDE2      ", 0xe37be2b5, 0x8671043b),
+	PCMCIA_DEVICE_PROD_ID12("M-Systems", "CF300", 0x7ed2ad87, 0x7e9e78ee),
 	PCMCIA_DEVICE_PROD_ID12("M-Systems", "CF500", 0x7ed2ad87, 0x7a13045c),
 	PCMCIA_DEVICE_PROD_ID2("NinjaATA-", 0xebe0bd79),
 	PCMCIA_DEVICE_PROD_ID12("PCMCIA", "CD-ROM", 0x281f1c5d, 0x66536591),
@@ -450,6 +451,7 @@ static struct pcmcia_device_id ide_ids[] = {
 	PCMCIA_DEVICE_PROD_ID12("SMI VENDOR", "SMI PRODUCT", 0x30896c92, 0x703cc5f6),
 	PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003),
 	PCMCIA_DEVICE_PROD_ID1("TRANSCEND    512M   ", 0xd0909443),
+	PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS1GCF45", 0x709b1bf1, 0xf68b6f32),
 	PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS1GCF80", 0x709b1bf1, 0x2a54d4b1),
 	PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS2GCF120", 0x709b1bf1, 0x969aa4f2),
 	PCMCIA_DEVICE_PROD_ID12("TRANSCEND", "TS4GCF120", 0x709b1bf1, 0xf54a91c8),
diff --git a/drivers/ide/legacy/macide.c b/drivers/ide/legacy/macide.c
index 1f527bbf8d9..2e84290d0bc 100644
--- a/drivers/ide/legacy/macide.c
+++ b/drivers/ide/legacy/macide.c
@@ -78,6 +78,8 @@ static void __init macide_setup_ports(hw_regs_t *hw, unsigned long base,
 
 	hw->irq = irq;
 	hw->ack_intr = ack_intr;
+
+	hw->chipset = ide_generic;
 }
 
 static const char *mac_ide_name[] =
@@ -95,6 +97,9 @@ static int __init macide_init(void)
 	int irq;
 	hw_regs_t hw;
 
+	if (!MACH_IS_MAC)
+		return -ENODEV;
+
 	switch (macintosh_config->ide_type) {
 	case MAC_IDE_QUADRA:
 		base = IDE_BASE;
diff --git a/drivers/ide/legacy/q40ide.c b/drivers/ide/legacy/q40ide.c
index 6f535d00e63..8ff6e2d2083 100644
--- a/drivers/ide/legacy/q40ide.c
+++ b/drivers/ide/legacy/q40ide.c
@@ -70,6 +70,8 @@ static void q40_ide_setup_ports(hw_regs_t *hw, unsigned long base,
 
 	hw->irq = irq;
 	hw->ack_intr = ack_intr;
+
+	hw->chipset = ide_generic;
 }
 
 static void q40ide_input_data(ide_drive_t *drive, struct request *rq,
diff --git a/drivers/ide/mips/swarm.c b/drivers/ide/mips/swarm.c
index 712d17bdd47..52fee3d2771 100644
--- a/drivers/ide/mips/swarm.c
+++ b/drivers/ide/mips/swarm.c
@@ -4,7 +4,7 @@
  *	Author:	Manish Lachwani, mlachwani@mvista.com
  * Copyright (C) 2004  MIPS Technologies, Inc.  All rights reserved.
  *	Author: Maciej W. Rozycki <macro@mips.com>
- * Copyright (c) 2006  Maciej W. Rozycki
+ * Copyright (c) 2006, 2008  Maciej W. Rozycki
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -70,8 +70,9 @@ static int __devinit swarm_ide_probe(struct device *dev)
 	ide_hwif_t *hwif;
 	u8 __iomem *base;
 	phys_t offset, size;
+	hw_regs_t hw;
 	int i;
-	u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+	u8 idx[] = { 0xff, 0xff, 0xff, 0xff };
 
 	if (!SIBYTE_HAVE_IDE)
 		return -ENODEV;
@@ -112,14 +113,15 @@ static int __devinit swarm_ide_probe(struct device *dev)
 	hwif->host_flags = IDE_HFLAG_MMIO;
 	default_hwif_mmiops(hwif);
 
-	hwif->chipset = ide_generic;
-
 	for (i = 0; i <= 7; i++)
-		hwif->io_ports_array[i] =
+		hw.io_ports_array[i] =
 				(unsigned long)(base + ((0x1f0 + i) << 5));
-	hwif->io_ports.ctl_addr =
+	hw.io_ports.ctl_addr =
 				(unsigned long)(base + (0x3f6 << 5));
-	hwif->irq = K_INT_GB_IDE;
+	hw.irq = K_INT_GB_IDE;
+	hw.chipset = ide_generic;
+
+	ide_init_port_hw(hwif, &hw);
 
 	idx[0] = hwif->index;
 
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index c1922f9cfe8..f2129d5e07f 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -39,6 +39,16 @@
 #include <asm/io.h>
 
 /*
+ * Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
+ * (this is DANGEROUS and could result in data corruption).
+ */
+static int wdc_udma;
+
+module_param(wdc_udma, bool, 0);
+MODULE_PARM_DESC(wdc_udma,
+		 "allow UDMA on M1543C-E chipset for WDC disks (DANGEROUS)");
+
+/*
  *	ALi devices are not plug in. Otherwise these static values would
  *	need to go. They ought to go away anyway
  */
@@ -76,11 +86,6 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
 		a_clc = 0;
 	c_time = ide_pio_timings[pio].cycle_time;
 
-#if 0
-	if ((r_clc = ((c_time - s_time - a_time) * bus_speed + 999) / 1000) >= 16)
-		r_clc = 0;
-#endif
-
 	if (!(r_clc = (c_time * bus_speed + 999) / 1000 - a_clc - s_clc)) {
 		r_clc = 1;
 	} else {
@@ -110,16 +115,6 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
 	pci_write_config_byte(dev, port, s_clc);
 	pci_write_config_byte(dev, port+drive->select.b.unit+2, (a_clc << 4) | r_clc);
 	local_irq_restore(flags);
-
-	/*
-	 * setup   active  rec
-	 * { 70,   165,    365 },   PIO Mode 0
-	 * { 50,   125,    208 },   PIO Mode 1
-	 * { 30,   100,    110 },   PIO Mode 2
-	 * { 30,   80,     70  },   PIO Mode 3 with IORDY
-	 * { 25,   70,     25  },   PIO Mode 4 with IORDY  ns
-	 * { 20,   50,     30  }    PIO Mode 5 with IORDY (nonstandard)
-	 */
 }
 
 /**
@@ -131,9 +126,7 @@ static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
  *	The actual rules for the ALi are:
  *		No UDMA on revisions <= 0x20
  *		Disk only for revisions < 0xC2
- *		Not WDC drives for revisions < 0xC2
- *
- *	FIXME: WDC ifdef needs to die
+ *		Not WDC drives on M1543C-E (?)
  */
 
 static u8 ali_udma_filter(ide_drive_t *drive)
@@ -141,10 +134,9 @@ static u8 ali_udma_filter(ide_drive_t *drive)
 	if (m5229_revision > 0x20 && m5229_revision < 0xC2) {
 		if (drive->media != ide_disk)
 			return 0;
-#ifndef CONFIG_WDC_ALI15X3
-		if (chip_is_1543c_e && strstr(drive->id->model, "WDC "))
+		if (chip_is_1543c_e && strstr(drive->id->model, "WDC ") &&
+		    wdc_udma == 0)
 			return 0;
-#endif
 	}
 
 	return drive->hwif->ultra_mask;
@@ -537,17 +529,9 @@ static const struct ide_port_info ali15x3_chipset __devinitdata = {
  
 static int __devinit alim15x3_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
-	static struct pci_device_id ati_rs100[] = {
-		{ PCI_DEVICE(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100) },
-		{ },
-	};
-
 	struct ide_port_info d = ali15x3_chipset;
 	u8 rev = dev->revision, idx = id->driver_data;
 
-	if (pci_dev_present(ati_rs100))
-		printk(KERN_WARNING "alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.\n");
-
 	/* don't use LBA48 DMA on ALi devices before rev 0xC5 */
 	if (rev <= 0xC4)
 		d.host_flags |= IDE_HFLAG_NO_LBA48_DMA;
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c
index aaf38109eae..b38a1980dcd 100644
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -747,9 +747,11 @@ static int __init cmd640x_init(void)
 
 	ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
 	hw[0].irq = 14;
+	hw[0].chipset = ide_cmd640;
 
 	ide_std_init_ports(&hw[1], 0x170, 0x376);
 	hw[1].irq = 15;
+	hw[1].chipset = ide_cmd640;
 
 	printk(KERN_INFO "cmd640: buggy cmd640%c interface on %s, config=0x%02x"
 			 "\n", 'a' + cmd640_chip_version - 1, bus_type, cfr);
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index 17669a43443..992b1cf8db6 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -119,6 +119,7 @@ static const struct ide_dma_ops cs5520_dma_ops = {
 	.dma_timeout		= ide_dma_timeout,
 };
 
+/* FIXME: VDMA is disabled because it caused system hangs */
 #define DECLARE_CS_DEV(name_str)				\
 	{							\
 		.name		= name_str,			\
@@ -126,7 +127,6 @@ static const struct ide_dma_ops cs5520_dma_ops = {
 		.dma_ops	= &cs5520_dma_ops,		\
 		.host_flags	= IDE_HFLAG_ISA_PORTS |		\
 				  IDE_HFLAG_CS5520 |		\
-				  IDE_HFLAG_VDMA |		\
 				  IDE_HFLAG_NO_ATAPI_DMA |	\
 				  IDE_HFLAG_ABUSE_SET_DMA_MODE, \
 		.pio_mask	= ATA_PIO4,			\
diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
index b9e457996d0..af0f30051d5 100644
--- a/drivers/ide/pci/delkin_cb.c
+++ b/drivers/ide/pci/delkin_cb.c
@@ -47,13 +47,18 @@ static const struct ide_port_ops delkin_cb_port_ops = {
 	.quirkproc		= ide_undecoded_slave,
 };
 
+static const struct ide_port_info delkin_cb_port_info = {
+	.port_ops		= &delkin_cb_port_ops,
+	.host_flags		= IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS |
+				  IDE_HFLAG_NO_DMA,
+};
+
 static int __devinit
 delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
 {
 	unsigned long base;
 	hw_regs_t hw;
 	ide_hwif_t *hwif = NULL;
-	ide_drive_t *drive;
 	int i, rc;
 	u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
 
@@ -79,6 +84,7 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
 	memset(&hw, 0, sizeof(hw));
 	ide_std_init_ports(&hw, base + 0x10, base + 0x1e);
 	hw.irq = dev->irq;
+	hw.dev = &dev->dev;
 	hw.chipset = ide_pci;		/* this enables IRQ sharing */
 
 	hwif = ide_find_port();
@@ -89,26 +95,16 @@ delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
 
 	ide_init_port_data(hwif, i);
 	ide_init_port_hw(hwif, &hw);
-	hwif->port_ops = &delkin_cb_port_ops;
 
 	idx[0] = i;
 
-	ide_device_add(idx, NULL);
-
-	if (!hwif->present)
-		goto out_disable;
+	ide_device_add(idx, &delkin_cb_port_info);
 
 	pci_set_drvdata(dev, hwif);
-	hwif->dev = &dev->dev;
-	drive = &hwif->drives[0];
-	if (drive->present) {
-		drive->io_32bit = 1;
-		drive->unmask   = 1;
-	}
+
 	return 0;
 
 out_disable:
-	printk(KERN_ERR "delkin_cb: no IDE devices found\n");
 	pci_release_regions(dev);
 	pci_disable_device(dev);
 	return -ENODEV;
@@ -139,14 +135,12 @@ static struct pci_driver driver = {
 	.remove		= delkin_cb_remove,
 };
 
-static int
-delkin_cb_init (void)
+static int __init delkin_cb_init(void)
 {
 	return pci_register_driver(&driver);
 }
 
-static void
-delkin_cb_exit (void)
+static void __exit delkin_cb_exit(void)
 {
 	pci_unregister_driver(&driver);
 }
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 6e99080497b..725c80508d9 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -81,8 +81,6 @@
  * 0.5 doesn't work.
  */
 
-#define OPTI621_DEBUG		/* define for debug messages */
-
 #include <linux/types.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -92,28 +90,6 @@
 
 #include <asm/io.h>
 
-//#define OPTI621_MAX_PIO 3
-/* In fact, I do not have any PIO 4 drive
- * (address: 25 ns, data: 70 ns, recovery: 35 ns),
- * but OPTi 82C621 is programmable and it can do (minimal values):
- * on 40MHz PCI bus (pulse 25 ns):
- *  address: 25 ns, data: 25 ns, recovery: 50 ns;
- * on 20MHz PCI bus (pulse 50 ns):
- *  address: 50 ns, data: 50 ns, recovery: 100 ns.
- */
-
-/* #define READ_PREFETCH 0 */
-/* Uncomment for disable read prefetch.
- * There is some readprefetch capatibility in hdparm,
- * but when I type hdparm -P 1 /dev/hda, I got errors
- * and till reset drive is inaccessible.
- * This (hw) read prefetch is safe on my drive.
- */
-
-#ifndef READ_PREFETCH
-#define READ_PREFETCH 0x40 /* read prefetch is enabled */
-#endif /* else read prefetch is disabled */
-
 #define READ_REG 0	/* index of Read cycle timing register */
 #define WRITE_REG 1	/* index of Write cycle timing register */
 #define CNTRL_REG 3	/* index of Control register */
@@ -122,51 +98,8 @@
 
 static int reg_base;
 
-#define PIO_NOT_EXIST 254
-#define PIO_DONT_KNOW 255
-
 static DEFINE_SPINLOCK(opti621_lock);
 
-/* there are stored pio numbers from other calls of opti621_set_pio_mode */
-static void compute_pios(ide_drive_t *drive, const u8 pio)
-/* Store values into drive->drive_data
- *	second_contr - 0 for primary controller, 1 for secondary
- *	slave_drive - 0 -> pio is for master, 1 -> pio is for slave
- *	pio - PIO mode for selected drive (for other we don't know)
- */
-{
-	int d;
-	ide_hwif_t *hwif = HWIF(drive);
-
-	drive->drive_data = pio;
-
-	for (d = 0; d < 2; ++d) {
-		drive = &hwif->drives[d];
-		if (drive->present) {
-			if (drive->drive_data == PIO_DONT_KNOW)
-				drive->drive_data = ide_get_best_pio_mode(drive, 255, 3);
-#ifdef OPTI621_DEBUG
-			printk("%s: Selected PIO mode %d\n",
-				drive->name, drive->drive_data);
-#endif
-		} else {
-			drive->drive_data = PIO_NOT_EXIST;
-		}
-	}
-}
-
-static int cmpt_clk(int time, int bus_speed)
-/* Returns (rounded up) time in clocks for time in ns,
- * with bus_speed in MHz.
- * Example: bus_speed = 40 MHz, time = 80 ns
- * 1000/40 = 25 ns (clk value),
- * 80/25 = 3.2, rounded up to 4 (I hope ;-)).
- * Use idebus=xx to select right frequency.
- */
-{
-	return ((time*bus_speed+999)/1000);
-}
-
 /* Write value to register reg, base of register
  * is at reg_base (0x1f0 primary, 0x170 secondary,
  * if not changed by PCI configuration).
@@ -199,83 +132,29 @@ static u8 read_reg(int reg)
 	return ret;
 }
 
-typedef struct pio_clocks_s {
-	int	address_time;	/* Address setup (clocks) */
-	int	data_time;	/* Active/data pulse (clocks) */
-	int	recovery_time;	/* Recovery time (clocks) */
-} pio_clocks_t;
-
-static void compute_clocks(int pio, pio_clocks_t *clks)
-{
-	if (pio != PIO_NOT_EXIST) {
-		int adr_setup, data_pls;
-		int bus_speed = ide_pci_clk ? ide_pci_clk : system_bus_clock();
-
-		adr_setup = ide_pio_timings[pio].setup_time;
-		data_pls = ide_pio_timings[pio].active_time;
-		clks->address_time = cmpt_clk(adr_setup, bus_speed);
-		clks->data_time = cmpt_clk(data_pls, bus_speed);
-		clks->recovery_time = cmpt_clk(ide_pio_timings[pio].cycle_time
-			- adr_setup-data_pls, bus_speed);
-		if (clks->address_time < 1)
-			clks->address_time = 1;
-		if (clks->address_time > 4)
-			clks->address_time = 4;
-		if (clks->data_time < 1)
-			clks->data_time = 1;
-		if (clks->data_time > 16)
-			clks->data_time = 16;
-		if (clks->recovery_time < 2)
-			clks->recovery_time = 2;
-		if (clks->recovery_time > 17)
-			clks->recovery_time = 17;
-	} else {
-		clks->address_time = 1;
-		clks->data_time = 1;
-		clks->recovery_time = 2;
-		/* minimal values */
-	}
-}
-
 static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-	/* primary and secondary drives share some registers,
-	 * so we have to program both drives
-	 */
+	ide_hwif_t *hwif = drive->hwif;
+	ide_drive_t *pair = ide_get_paired_drive(drive);
 	unsigned long flags;
-	u8 pio1 = 0, pio2 = 0;
-	pio_clocks_t first, second;
-	int ax, drdy;
-	u8 cycle1, cycle2, misc;
-	ide_hwif_t *hwif = HWIF(drive);
-
-	/* sets drive->drive_data for both drives */
-	compute_pios(drive, pio);
-	pio1 = hwif->drives[0].drive_data;
-	pio2 = hwif->drives[1].drive_data;
-
-	compute_clocks(pio1, &first);
-	compute_clocks(pio2, &second);
-
-	/* ax = max(a1,a2) */
-	ax = (first.address_time < second.address_time) ? second.address_time : first.address_time;
-
-	drdy = 2; /* DRDY is default 2 (by OPTi Databook) */
-
-	cycle1 = ((first.data_time-1)<<4)  | (first.recovery_time-2);
-	cycle2 = ((second.data_time-1)<<4) | (second.recovery_time-2);
-	misc = READ_PREFETCH | ((ax-1)<<4) | ((drdy-2)<<1);
-
-#ifdef OPTI621_DEBUG
-	printk("%s: master: address: %d, data: %d, "
-		"recovery: %d, drdy: %d [clk]\n",
-		hwif->name, ax, first.data_time,
-		first.recovery_time, drdy);
-	printk("%s: slave:  address: %d, data: %d, "
-		"recovery: %d, drdy: %d [clk]\n",
-		hwif->name, ax, second.data_time,
-		second.recovery_time, drdy);
-#endif
+	u8 tim, misc, addr_pio = pio, clk;
+
+	/* DRDY is default 2 (by OPTi Databook) */
+	static const u8 addr_timings[2][5] = {
+		{ 0x20, 0x10, 0x00, 0x00, 0x00 },	/* 33 MHz */
+		{ 0x10, 0x10, 0x00, 0x00, 0x00 },	/* 25 MHz */
+	};
+	static const u8 data_rec_timings[2][5] = {
+		{ 0x5b, 0x45, 0x32, 0x21, 0x20 },	/* 33 MHz */
+		{ 0x48, 0x34, 0x21, 0x10, 0x10 }	/* 25 MHz */
+	};
+
+	drive->drive_data = XFER_PIO_0 + pio;
+
+	if (pair->present) {
+		if (pair->drive_data && pair->drive_data < drive->drive_data)
+			addr_pio = pair->drive_data - XFER_PIO_0;
+	}
 
 	spin_lock_irqsave(&opti621_lock, flags);
 
@@ -289,24 +168,21 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
 	(void)inb(reg_base + CNTRL_REG);
 	/* if reads 0xc0, no interface exist? */
 	read_reg(CNTRL_REG);
-	/* read version, probably 0 */
-	read_reg(STRAP_REG);
 
-	/* program primary drive */
-	/* select Index-0 for Register-A */
-	write_reg(0, MISC_REG);
-	/* set read cycle timings */
-	write_reg(cycle1, READ_REG);
-	/* set write cycle timings */
-	write_reg(cycle1, WRITE_REG);
+	/* check CLK speed */
+	clk = read_reg(STRAP_REG) & 1;
+
+	printk(KERN_INFO "%s: CLK = %d MHz\n", hwif->name, clk ? 25 : 33);
 
-	/* program secondary drive */
-	/* select Index-1 for Register-B */
-	write_reg(1, MISC_REG);
+	tim  = data_rec_timings[clk][pio];
+	misc = addr_timings[clk][addr_pio];
+
+	/* select Index-0/1 for Register-A/B */
+	write_reg(drive->select.b.unit, MISC_REG);
 	/* set read cycle timings */
-	write_reg(cycle2, READ_REG);
+	write_reg(tim, READ_REG);
 	/* set write cycle timings */
-	write_reg(cycle2, WRITE_REG);
+	write_reg(tim, WRITE_REG);
 
 	/* use Register-A for drive 0 */
 	/* use Register-B for drive 1 */
@@ -319,45 +195,26 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
 	spin_unlock_irqrestore(&opti621_lock, flags);
 }
 
-static void __devinit opti621_port_init_devs(ide_hwif_t *hwif)
-{
-	hwif->drives[0].drive_data = PIO_DONT_KNOW;
-	hwif->drives[1].drive_data = PIO_DONT_KNOW;
-}
-
 static const struct ide_port_ops opti621_port_ops = {
-	.port_init_devs		= opti621_port_init_devs,
 	.set_pio_mode		= opti621_set_pio_mode,
 };
 
-static const struct ide_port_info opti621_chipsets[] __devinitdata = {
-	{	/* 0 */
-		.name		= "OPTI621",
-		.enablebits	= { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
-		.port_ops	= &opti621_port_ops,
-		.host_flags	= IDE_HFLAG_TRUST_BIOS_FOR_DMA,
-		.pio_mask	= ATA_PIO3,
-		.swdma_mask	= ATA_SWDMA2,
-		.mwdma_mask	= ATA_MWDMA2,
-	}, {	/* 1 */
-		.name		= "OPTI621X",
-		.enablebits	= { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
-		.port_ops	= &opti621_port_ops,
-		.host_flags	= IDE_HFLAG_TRUST_BIOS_FOR_DMA,
-		.pio_mask	= ATA_PIO3,
-		.swdma_mask	= ATA_SWDMA2,
-		.mwdma_mask	= ATA_MWDMA2,
-	}
+static const struct ide_port_info opti621_chipset __devinitdata = {
+	.name		= "OPTI621/X",
+	.enablebits	= { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
+	.port_ops	= &opti621_port_ops,
+	.host_flags	= IDE_HFLAG_NO_DMA,
+	.pio_mask	= ATA_PIO4,
 };
 
 static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 {
-	return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]);
+	return ide_setup_pci_device(dev, &opti621_chipset);
 }
 
 static const struct pci_device_id opti621_pci_tbl[] = {
 	{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
-	{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
+	{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
 	{ 0, },
 };
 MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 4b0b85d8faf..e127eb25ab6 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -569,6 +569,11 @@ static int __devinit sis5513_init_one(struct pci_dev *dev, const struct pci_devi
 {
 	struct ide_port_info d = sis5513_chipset;
 	u8 udma_rates[] = { 0x00, 0x00, 0x07, 0x1f, 0x3f, 0x3f, 0x7f, 0x7f };
+	int rc;
+
+	rc = pci_enable_device(dev);
+	if (rc)
+		return rc;
 
 	if (sis_find_family(dev) == 0)
 		return -ENOTSUPP;
diff --git a/drivers/ide/ppc/mpc8xx.c b/drivers/ide/ppc/mpc8xx.c
index f0e638dcc3a..236f9c38e51 100644
--- a/drivers/ide/ppc/mpc8xx.c
+++ b/drivers/ide/ppc/mpc8xx.c
@@ -303,6 +303,8 @@ static int __init m8xx_ide_init_ports(hw_regs_t *hw, unsigned long data_port)
 	pcmp->pcmc_per = 0x100000 >> (16 * _slot_);
 #endif	/* CONFIG_IDE_8xx_PCCARD */
 
+	hw->chipset = ide_generic;
+
 	return 0;
 }
 #endif /* CONFIG_IDE_8xx_PCCARD || CONFIG_IDE_8xx_DIRECT */
@@ -377,6 +379,8 @@ static int __init m8xx_ide_init_ports(hw_regs_t *hw, unsigned long data_port)
 	((immap_t *) IMAP_ADDR)->im_siu_conf.sc_siel |=
 			(0x80000000 >> ioport_dsc[data_port].irq);
 
+	hw->chipset = ide_generic;
+
 	return 0;
 }
 #endif	/* CONFIG_IDE_8xx_DIRECT */
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index 48aa019127b..ba2d5872796 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -59,7 +59,6 @@ typedef struct pmac_ide_hwif {
 	int				irq;
 	int				kind;
 	int				aapl_bus_id;
-	unsigned			cable_80 : 1;
 	unsigned			mediabay : 1;
 	unsigned			broken_dma : 1;
 	unsigned			broken_dma_warn : 1;
@@ -918,10 +917,40 @@ pmac_ide_do_resume(ide_hwif_t *hwif)
 	return 0;
 }
 
+static u8 pmac_ide_cable_detect(ide_hwif_t *hwif)
+{
+	pmac_ide_hwif_t *pmif = (pmac_ide_hwif_t *)ide_get_hwifdata(hwif);
+	struct device_node *np = pmif->node;
+	const char *cable = of_get_property(np, "cable-type", NULL);
+
+	/* Get cable type from device-tree. */
+	if (cable && !strncmp(cable, "80-", 3))
+		return ATA_CBL_PATA80;
+
+	/*
+	 * G5's seem to have incorrect cable type in device-tree.
+	 * Let's assume they have a 80 conductor cable, this seem
+	 * to be always the case unless the user mucked around.
+	 */
+	if (of_device_is_compatible(np, "K2-UATA") ||
+	    of_device_is_compatible(np, "shasta-ata"))
+		return ATA_CBL_PATA80;
+
+	return ATA_CBL_PATA40;
+}
+
 static const struct ide_port_ops pmac_ide_ata6_port_ops = {
 	.set_pio_mode		= pmac_ide_set_pio_mode,
 	.set_dma_mode		= pmac_ide_set_dma_mode,
 	.selectproc		= pmac_ide_kauai_selectproc,
+	.cable_detect		= pmac_ide_cable_detect,
+};
+
+static const struct ide_port_ops pmac_ide_ata4_port_ops = {
+	.set_pio_mode		= pmac_ide_set_pio_mode,
+	.set_dma_mode		= pmac_ide_set_dma_mode,
+	.selectproc		= pmac_ide_selectproc,
+	.cable_detect		= pmac_ide_cable_detect,
 };
 
 static const struct ide_port_ops pmac_ide_port_ops = {
@@ -949,10 +978,7 @@ static const struct ide_port_info pmac_port_info = {
 
 /*
  * Setup, register & probe an IDE channel driven by this driver, this is
- * called by one of the 2 probe functions (macio or PCI). Note that a channel
- * that ends up beeing free of any device is not kept around by this driver
- * (it is kept in 2.4). This introduce an interface numbering change on some
- * rare machines unfortunately, but it's better this way.
+ * called by one of the 2 probe functions (macio or PCI).
  */
 static int __devinit
 pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
@@ -962,7 +988,6 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
 	u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
 	struct ide_port_info d = pmac_port_info;
 
-	pmif->cable_80 = 0;
 	pmif->broken_dma = pmif->broken_dma_warn = 0;
 	if (of_device_is_compatible(np, "shasta-ata")) {
 		pmif->kind = controller_sh_ata6;
@@ -979,6 +1004,7 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
 	} else if (of_device_is_compatible(np, "keylargo-ata")) {
 		if (strcmp(np->name, "ata-4") == 0) {
 			pmif->kind = controller_kl_ata4;
+			d.port_ops = &pmac_ide_ata4_port_ops;
 			d.udma_mask = ATA_UDMA4;
 		} else
 			pmif->kind = controller_kl_ata3;
@@ -992,22 +1018,6 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
 	bidp = of_get_property(np, "AAPL,bus-id", NULL);
 	pmif->aapl_bus_id =  bidp ? *bidp : 0;
 
-	/* Get cable type from device-tree */
-	if (pmif->kind == controller_kl_ata4 || pmif->kind == controller_un_ata6
-	    || pmif->kind == controller_k2_ata6
-	    || pmif->kind == controller_sh_ata6) {
-		const char* cable = of_get_property(np, "cable-type", NULL);
-		if (cable && !strncmp(cable, "80-", 3))
-			pmif->cable_80 = 1;
-	}
-	/* G5's seem to have incorrect cable type in device-tree. Let's assume
-	 * they have a 80 conductor cable, this seem to be always the case unless
-	 * the user mucked around
-	 */
-	if (of_device_is_compatible(np, "K2-UATA") ||
-	    of_device_is_compatible(np, "shasta-ata"))
-		pmif->cable_80 = 1;
-
 	/* On Kauai-type controllers, we make sure the FCR is correct */
 	if (pmif->kauai_fcr)
 		writel(KAUAI_FCR_UATA_MAGIC |
@@ -1053,7 +1063,6 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
 
 	hwif->hwif_data = pmif;
 	ide_init_port_hw(hwif, hw);
-	hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
 
 	printk(KERN_INFO "ide%d: Found Apple %s controller, bus ID %d%s, irq %d\n",
 	       hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
@@ -1070,11 +1079,6 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif, hw_regs_t *hw)
 		}
 	}
 
-#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
-	if (pmif->cable_80 == 0)
-		d.udma_mask &= ATA_UDMA2;
-#endif
-
 	idx[0] = hwif->index;
 
 	ide_device_add(idx, &d);