IB/ipath: support new QLogic product naming scheme

This patch only renames files, fixes product names, and updates
comments.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

1 files changed, 0 insertions, 1603 deletions

diff --git a/drivers/infiniband/hw/ipath/ipath_ht400.c b/drivers/infiniband/hw/ipath/ipath_ht400.c
deleted file mode 100644
index 3db015da6e7..00000000000
--- a/drivers/infiniband/hw/ipath/ipath_ht400.c
+++ /dev/null
@@ -1,1603 +0,0 @@
-/*
- * Copyright (c) 2006 QLogic, Inc. All rights reserved.
- * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
- *
- * This software is available to you under a choice of one of two
- * licenses.  You may choose to be licensed under the terms of the GNU
- * General Public License (GPL) Version 2, available from the file
- * COPYING in the main directory of this source tree, or the
- * OpenIB.org BSD license below:
- *
- *     Redistribution and use in source and binary forms, with or
- *     without modification, are permitted provided that the following
- *     conditions are met:
- *
- *      - Redistributions of source code must retain the above
- *        copyright notice, this list of conditions and the following
- *        disclaimer.
- *
- *      - Redistributions in binary form must reproduce the above
- *        copyright notice, this list of conditions and the following
- *        disclaimer in the documentation and/or other materials
- *        provided with the distribution.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
- * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
- * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
- * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
- * SOFTWARE.
- */
-
-/*
- * This file contains all of the code that is specific to the InfiniPath
- * HT-400 chip.
- */
-
-#include <linux/pci.h>
-#include <linux/delay.h>
-
-#include "ipath_kernel.h"
-#include "ipath_registers.h"
-
-/*
- * This lists the InfiniPath HT400 registers, in the actual chip layout.
- * This structure should never be directly accessed.
- *
- * The names are in InterCap form because they're taken straight from
- * the chip specification.  Since they're only used in this file, they
- * don't pollute the rest of the source.
-*/
-
-struct _infinipath_do_not_use_kernel_regs {
-	unsigned long long Revision;
-	unsigned long long Control;
-	unsigned long long PageAlign;
-	unsigned long long PortCnt;
-	unsigned long long DebugPortSelect;
-	unsigned long long DebugPort;
-	unsigned long long SendRegBase;
-	unsigned long long UserRegBase;
-	unsigned long long CounterRegBase;
-	unsigned long long Scratch;
-	unsigned long long ReservedMisc1;
-	unsigned long long InterruptConfig;
-	unsigned long long IntBlocked;
-	unsigned long long IntMask;
-	unsigned long long IntStatus;
-	unsigned long long IntClear;
-	unsigned long long ErrorMask;
-	unsigned long long ErrorStatus;
-	unsigned long long ErrorClear;
-	unsigned long long HwErrMask;
-	unsigned long long HwErrStatus;
-	unsigned long long HwErrClear;
-	unsigned long long HwDiagCtrl;
-	unsigned long long MDIO;
-	unsigned long long IBCStatus;
-	unsigned long long IBCCtrl;
-	unsigned long long ExtStatus;
-	unsigned long long ExtCtrl;
-	unsigned long long GPIOOut;
-	unsigned long long GPIOMask;
-	unsigned long long GPIOStatus;
-	unsigned long long GPIOClear;
-	unsigned long long RcvCtrl;
-	unsigned long long RcvBTHQP;
-	unsigned long long RcvHdrSize;
-	unsigned long long RcvHdrCnt;
-	unsigned long long RcvHdrEntSize;
-	unsigned long long RcvTIDBase;
-	unsigned long long RcvTIDCnt;
-	unsigned long long RcvEgrBase;
-	unsigned long long RcvEgrCnt;
-	unsigned long long RcvBufBase;
-	unsigned long long RcvBufSize;
-	unsigned long long RxIntMemBase;
-	unsigned long long RxIntMemSize;
-	unsigned long long RcvPartitionKey;
-	unsigned long long ReservedRcv[10];
-	unsigned long long SendCtrl;
-	unsigned long long SendPIOBufBase;
-	unsigned long long SendPIOSize;
-	unsigned long long SendPIOBufCnt;
-	unsigned long long SendPIOAvailAddr;
-	unsigned long long TxIntMemBase;
-	unsigned long long TxIntMemSize;
-	unsigned long long ReservedSend[9];
-	unsigned long long SendBufferError;
-	unsigned long long SendBufferErrorCONT1;
-	unsigned long long SendBufferErrorCONT2;
-	unsigned long long SendBufferErrorCONT3;
-	unsigned long long ReservedSBE[4];
-	unsigned long long RcvHdrAddr0;
-	unsigned long long RcvHdrAddr1;
-	unsigned long long RcvHdrAddr2;
-	unsigned long long RcvHdrAddr3;
-	unsigned long long RcvHdrAddr4;
-	unsigned long long RcvHdrAddr5;
-	unsigned long long RcvHdrAddr6;
-	unsigned long long RcvHdrAddr7;
-	unsigned long long RcvHdrAddr8;
-	unsigned long long ReservedRHA[7];
-	unsigned long long RcvHdrTailAddr0;
-	unsigned long long RcvHdrTailAddr1;
-	unsigned long long RcvHdrTailAddr2;
-	unsigned long long RcvHdrTailAddr3;
-	unsigned long long RcvHdrTailAddr4;
-	unsigned long long RcvHdrTailAddr5;
-	unsigned long long RcvHdrTailAddr6;
-	unsigned long long RcvHdrTailAddr7;
-	unsigned long long RcvHdrTailAddr8;
-	unsigned long long ReservedRHTA[7];
-	unsigned long long Sync;	/* Software only */
-	unsigned long long Dump;	/* Software only */
-	unsigned long long SimVer;	/* Software only */
-	unsigned long long ReservedSW[5];
-	unsigned long long SerdesConfig0;
-	unsigned long long SerdesConfig1;
-	unsigned long long SerdesStatus;
-	unsigned long long XGXSConfig;
-	unsigned long long ReservedSW2[4];
-};
-
-#define IPATH_KREG_OFFSET(field) (offsetof(struct \
-    _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
-#define IPATH_CREG_OFFSET(field) (offsetof( \
-    struct infinipath_counters, field) / sizeof(u64))
-
-static const struct ipath_kregs ipath_ht_kregs = {
-	.kr_control = IPATH_KREG_OFFSET(Control),
-	.kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
-	.kr_debugport = IPATH_KREG_OFFSET(DebugPort),
-	.kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
-	.kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
-	.kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
-	.kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
-	.kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
-	.kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
-	.kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
-	.kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
-	.kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
-	.kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
-	.kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
-	.kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
-	.kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
-	.kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
-	.kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
-	.kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
-	.kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
-	.kr_intclear = IPATH_KREG_OFFSET(IntClear),
-	.kr_interruptconfig = IPATH_KREG_OFFSET(InterruptConfig),
-	.kr_intmask = IPATH_KREG_OFFSET(IntMask),
-	.kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
-	.kr_mdio = IPATH_KREG_OFFSET(MDIO),
-	.kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
-	.kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
-	.kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
-	.kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
-	.kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
-	.kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
-	.kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
-	.kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
-	.kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
-	.kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
-	.kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
-	.kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
-	.kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
-	.kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
-	.kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
-	.kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
-	.kr_revision = IPATH_KREG_OFFSET(Revision),
-	.kr_scratch = IPATH_KREG_OFFSET(Scratch),
-	.kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
-	.kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
-	.kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
-	.kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
-	.kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
-	.kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
-	.kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
-	.kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
-	.kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
-	.kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
-	.kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
-	.kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
-	.kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
-	.kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
-	/*
-	 * These should not be used directly via ipath_read_kreg64(),
-	 * use them with ipath_read_kreg64_port(),
-	 */
-	.kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
-	.kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0)
-};
-
-static const struct ipath_cregs ipath_ht_cregs = {
-	.cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
-	.cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
-	.cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
-	.cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
-	.cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
-	.cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
-	.cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
-	.cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
-	.cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
-	.cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
-	.cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
-	.cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
-	/* calc from Reg_CounterRegBase + offset */
-	.cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
-	.cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
-	.cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
-	.cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
-	.cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
-	.cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
-	.cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
-	.cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
-	.cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
-	.cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
-	.cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
-	.cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
-	.cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
-	.cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
-	.cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
-	.cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
-	.cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
-	.cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
-	.cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
-	.cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
-	.cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
-};
-
-/* kr_intstatus, kr_intclear, kr_intmask bits */
-#define INFINIPATH_I_RCVURG_MASK 0x1FF
-#define INFINIPATH_I_RCVAVAIL_MASK 0x1FF
-
-/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
-#define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0
-#define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL
-#define INFINIPATH_HWE_HTCLNKABYTE0CRCERR   0x0000000000800000ULL
-#define INFINIPATH_HWE_HTCLNKABYTE1CRCERR   0x0000000001000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR   0x0000000002000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR   0x0000000004000000ULL
-#define INFINIPATH_HWE_HTCMISCERR4          0x0000000008000000ULL
-#define INFINIPATH_HWE_HTCMISCERR5          0x0000000010000000ULL
-#define INFINIPATH_HWE_HTCMISCERR6          0x0000000020000000ULL
-#define INFINIPATH_HWE_HTCMISCERR7          0x0000000040000000ULL
-#define INFINIPATH_HWE_HTCBUSTREQPARITYERR  0x0000000080000000ULL
-#define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL
-#define INFINIPATH_HWE_HTCBUSIREQPARITYERR  0x0000000200000000ULL
-#define INFINIPATH_HWE_COREPLL_FBSLIP       0x0080000000000000ULL
-#define INFINIPATH_HWE_COREPLL_RFSLIP       0x0100000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_FBSLIP        0x0200000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_RFSLIP        0x0400000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_FBSLIP        0x0800000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_RFSLIP        0x1000000000000000ULL
-#define INFINIPATH_HWE_SERDESPLLFAILED      0x2000000000000000ULL
-
-/* kr_extstatus bits */
-#define INFINIPATH_EXTS_FREQSEL 0x2
-#define INFINIPATH_EXTS_SERDESSEL 0x4
-#define INFINIPATH_EXTS_MEMBIST_ENDTEST     0x0000000000004000
-#define INFINIPATH_EXTS_MEMBIST_CORRECT     0x0000000000008000
-
-/*
- * masks and bits that are different in different chips, or present only
- * in one
- */
-static const ipath_err_t infinipath_hwe_htcmemparityerr_mask =
-    INFINIPATH_HWE_HTCMEMPARITYERR_MASK;
-static const ipath_err_t infinipath_hwe_htcmemparityerr_shift =
-    INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT;
-
-static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr =
-    INFINIPATH_HWE_HTCLNKABYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr =
-    INFINIPATH_HWE_HTCLNKABYTE1CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr =
-    INFINIPATH_HWE_HTCLNKBBYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr =
-    INFINIPATH_HWE_HTCLNKBBYTE1CRCERR;
-
-#define _IPATH_GPIO_SDA_NUM 1
-#define _IPATH_GPIO_SCL_NUM 0
-
-#define IPATH_GPIO_SDA \
-	(1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-#define IPATH_GPIO_SCL \
-	(1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-
-/* keep the code below somewhat more readonable; not used elsewhere */
-#define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr |	\
-				infinipath_hwe_htclnkabyte1crcerr)
-#define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr |	\
-				infinipath_hwe_htclnkbbyte1crcerr)
-#define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr |	\
-				infinipath_hwe_htclnkbbyte0crcerr)
-#define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr |	\
-				infinipath_hwe_htclnkbbyte1crcerr)
-
-static void hwerr_crcbits(struct ipath_devdata *dd, ipath_err_t hwerrs,
-			  char *msg, size_t msgl)
-{
-	char bitsmsg[64];
-	ipath_err_t crcbits = hwerrs &
-		(_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS);
-	/* don't check if 8bit HT */
-	if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
-		crcbits &= ~infinipath_hwe_htclnkabyte1crcerr;
-	/* don't check if 8bit HT */
-	if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
-		crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr;
-	/*
-	 * we'll want to ignore link errors on link that is
-	 * not in use, if any.  For now, complain about both
-	 */
-	if (crcbits) {
-		u16 ctrl0, ctrl1;
-		snprintf(bitsmsg, sizeof bitsmsg,
-			 "[HT%s lane %s CRC (%llx); ignore till reload]",
-			 !(crcbits & _IPATH_HTLINK1_CRCBITS) ?
-			 "0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS)
-				    ? "1 (B)" : "0+1 (A+B)"),
-			 !(crcbits & _IPATH_HTLANE1_CRCBITS) ? "0"
-			 : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ? "1" :
-			    "0+1"), (unsigned long long) crcbits);
-		strlcat(msg, bitsmsg, msgl);
-
-		/*
-		 * print extra info for debugging.  slave/primary
-		 * config word 4, 8 (link control 0, 1)
-		 */
-
-		if (pci_read_config_word(dd->pcidev,
-					 dd->ipath_ht_slave_off + 0x4,
-					 &ctrl0))
-			dev_info(&dd->pcidev->dev, "Couldn't read "
-				 "linkctrl0 of slave/primary "
-				 "config block\n");
-		else if (!(ctrl0 & 1 << 6))
-			/* not if EOC bit set */
-			ipath_dbg("HT linkctrl0 0x%x%s%s\n", ctrl0,
-				  ((ctrl0 >> 8) & 7) ? " CRC" : "",
-				  ((ctrl0 >> 4) & 1) ? "linkfail" :
-				  "");
-		if (pci_read_config_word(dd->pcidev,
-					 dd->ipath_ht_slave_off + 0x8,
-					 &ctrl1))
-			dev_info(&dd->pcidev->dev, "Couldn't read "
-				 "linkctrl1 of slave/primary "
-				 "config block\n");
-		else if (!(ctrl1 & 1 << 6))
-			/* not if EOC bit set */
-			ipath_dbg("HT linkctrl1 0x%x%s%s\n", ctrl1,
-				  ((ctrl1 >> 8) & 7) ? " CRC" : "",
-				  ((ctrl1 >> 4) & 1) ? "linkfail" :
-				  "");
-
-		/* disable until driver reloaded */
-		dd->ipath_hwerrmask &= ~crcbits;
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
-				 dd->ipath_hwerrmask);
-		ipath_dbg("HT crc errs: %s\n", msg);
-	} else
-		ipath_dbg("ignoring HT crc errors 0x%llx, "
-			  "not in use\n", (unsigned long long)
-			  (hwerrs & (_IPATH_HTLINK0_CRCBITS |
-				     _IPATH_HTLINK1_CRCBITS)));
-}
-
-/**
- * ipath_ht_handle_hwerrors - display hardware errors
- * @dd: the infinipath device
- * @msg: the output buffer
- * @msgl: the size of the output buffer
- *
- * Use same msg buffer as regular errors to avoid
- * excessive stack use.  Most hardware errors are catastrophic, but for
- * right now, we'll print them and continue.
- * We reuse the same message buffer as ipath_handle_errors() to avoid
- * excessive stack usage.
- */
-static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg,
-				     size_t msgl)
-{
-	ipath_err_t hwerrs;
-	u32 bits, ctrl;
-	int isfatal = 0;
-	char bitsmsg[64];
-
-	hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
-
-	if (!hwerrs) {
-		ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
-		/*
-		 * better than printing cofusing messages
-		 * This seems to be related to clearing the crc error, or
-		 * the pll error during init.
-		 */
-		goto bail;
-	} else if (hwerrs == -1LL) {
-		ipath_dev_err(dd, "Read of hardware error status failed "
-			      "(all bits set); ignoring\n");
-		goto bail;
-	}
-	ipath_stats.sps_hwerrs++;
-
-	/* Always clear the error status register, except MEMBISTFAIL,
-	 * regardless of whether we continue or stop using the chip.
-	 * We want that set so we know it failed, even across driver reload.
-	 * We'll still ignore it in the hwerrmask.  We do this partly for
-	 * diagnostics, but also for support */
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
-			 hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
-
-	hwerrs &= dd->ipath_hwerrmask;
-
-	/*
-	 * make sure we get this much out, unless told to be quiet,
-	 * or it's occurred within the last 5 seconds
-	 */
-	if ((hwerrs & ~dd->ipath_lasthwerror) ||
-	    (ipath_debug & __IPATH_VERBDBG))
-		dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
-			 "(cleared)\n", (unsigned long long) hwerrs);
-	dd->ipath_lasthwerror |= hwerrs;
-
-	if (hwerrs & ~infinipath_hwe_bitsextant)
-		ipath_dev_err(dd, "hwerror interrupt with unknown errors "
-			      "%llx set\n", (unsigned long long)
-			      (hwerrs & ~infinipath_hwe_bitsextant));
-
-	ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
-	if (ctrl & INFINIPATH_C_FREEZEMODE) {
-		if (hwerrs) {
-			/*
-			 * if any set that we aren't ignoring; only
-			 * make the complaint once, in case it's stuck
-			 * or recurring, and we get here multiple
-			 * times.
-			 */
-			if (dd->ipath_flags & IPATH_INITTED) {
-				ipath_dev_err(dd, "Fatal Error (freeze "
-					      "mode), no longer usable\n");
-				isfatal = 1;
-			}
-			*dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
-			/* mark as having had error */
-			*dd->ipath_statusp |= IPATH_STATUS_HWERROR;
-			/*
-			 * mark as not usable, at a minimum until driver
-			 * is reloaded, probably until reboot, since no
-			 * other reset is possible.
-			 */
-			dd->ipath_flags &= ~IPATH_INITTED;
-		} else {
-			ipath_dbg("Clearing freezemode on ignored hardware "
-				  "error\n");
-			ctrl &= ~INFINIPATH_C_FREEZEMODE;
-			ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
-					 ctrl);
-		}
-	}
-
-	*msg = '\0';
-
-	/*
-	 * may someday want to decode into which bits are which
-	 * functional area for parity errors, etc.
-	 */
-	if (hwerrs & (infinipath_hwe_htcmemparityerr_mask
-		      << INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT)) {
-		bits = (u32) ((hwerrs >>
-			       INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) &
-			      INFINIPATH_HWE_HTCMEMPARITYERR_MASK);
-		snprintf(bitsmsg, sizeof bitsmsg, "[HTC Parity Errs %x] ",
-			 bits);
-		strlcat(msg, bitsmsg, msgl);
-	}
-	if (hwerrs & (INFINIPATH_HWE_RXEMEMPARITYERR_MASK
-		      << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)) {
-		bits = (u32) ((hwerrs >>
-			       INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) &
-			      INFINIPATH_HWE_RXEMEMPARITYERR_MASK);
-		snprintf(bitsmsg, sizeof bitsmsg, "[RXE Parity Errs %x] ",
-			 bits);
-		strlcat(msg, bitsmsg, msgl);
-	}
-	if (hwerrs & (INFINIPATH_HWE_TXEMEMPARITYERR_MASK
-		      << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
-		bits = (u32) ((hwerrs >>
-			       INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) &
-			      INFINIPATH_HWE_TXEMEMPARITYERR_MASK);
-		snprintf(bitsmsg, sizeof bitsmsg, "[TXE Parity Errs %x] ",
-			 bits);
-		strlcat(msg, bitsmsg, msgl);
-	}
-	if (hwerrs & INFINIPATH_HWE_IBCBUSTOSPCPARITYERR)
-		strlcat(msg, "[IB2IPATH Parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_IBCBUSFRSPCPARITYERR)
-		strlcat(msg, "[IPATH2IB Parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_HTCBUSIREQPARITYERR)
-		strlcat(msg, "[HTC Ireq Parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_HTCBUSTREQPARITYERR)
-		strlcat(msg, "[HTC Treq Parity]", msgl);
-	if (hwerrs & INFINIPATH_HWE_HTCBUSTRESPPARITYERR)
-		strlcat(msg, "[HTC Tresp Parity]", msgl);
-
-	if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS))
-		hwerr_crcbits(dd, hwerrs, msg, msgl);
-
-	if (hwerrs & INFINIPATH_HWE_HTCMISCERR5)
-		strlcat(msg, "[HT core Misc5]", msgl);
-	if (hwerrs & INFINIPATH_HWE_HTCMISCERR6)
-		strlcat(msg, "[HT core Misc6]", msgl);
-	if (hwerrs & INFINIPATH_HWE_HTCMISCERR7)
-		strlcat(msg, "[HT core Misc7]", msgl);
-	if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
-		strlcat(msg, "[Memory BIST test failed, HT-400 unusable]",
-			msgl);
-		/* ignore from now on, so disable until driver reloaded */
-		dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
-				 dd->ipath_hwerrmask);
-	}
-#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP |	\
-			 INFINIPATH_HWE_COREPLL_RFSLIP |	\
-			 INFINIPATH_HWE_HTBPLL_FBSLIP |		\
-			 INFINIPATH_HWE_HTBPLL_RFSLIP |		\
-			 INFINIPATH_HWE_HTAPLL_FBSLIP |		\
-			 INFINIPATH_HWE_HTAPLL_RFSLIP)
-
-	if (hwerrs & _IPATH_PLL_FAIL) {
-		snprintf(bitsmsg, sizeof bitsmsg,
-			 "[PLL failed (%llx), HT-400 unusable]",
-			 (unsigned long long) (hwerrs & _IPATH_PLL_FAIL));
-		strlcat(msg, bitsmsg, msgl);
-		/* ignore from now on, so disable until driver reloaded */
-		dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
-				 dd->ipath_hwerrmask);
-	}
-
-	if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
-		/*
-		 * If it occurs, it is left masked since the eternal
-		 * interface is unused
-		 */
-		dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
-				 dd->ipath_hwerrmask);
-	}
-
-	if (hwerrs & INFINIPATH_HWE_RXDSYNCMEMPARITYERR)
-		strlcat(msg, "[Rx Dsync]", msgl);
-	if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED)
-		strlcat(msg, "[SerDes PLL]", msgl);
-
-	ipath_dev_err(dd, "%s hardware error\n", msg);
-	if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg)
-		/*
-		 * for status file; if no trailing brace is copied,
-		 * we'll know it was truncated.
-		 */
-		snprintf(dd->ipath_freezemsg,
-			 dd->ipath_freezelen, "{%s}", msg);
-
-bail:;
-}
-
-/**
- * ipath_ht_boardname - fill in the board name
- * @dd: the infinipath device
- * @name: the output buffer
- * @namelen: the size of the output buffer
- *
- * fill in the board name, based on the board revision register
- */
-static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
-			      size_t namelen)
-{
-	char *n = NULL;
-	u8 boardrev = dd->ipath_boardrev;
-	int ret;
-
-	switch (boardrev) {
-	case 4:		/* Ponderosa is one of the bringup boards */
-		n = "Ponderosa";
-		break;
-	case 5:
-		/*
-		 * HT-460 original production board; two production levels, with
-		 * different serial number ranges.   See ipath_ht_early_init() for
-		 * case where we enable IPATH_GPIO_INTR for later serial # range.
-		 */
-		n = "InfiniPath_HT-460";
-		break;
-	case 6:
-		n = "OEM_Board_3";
-		break;
-	case 7:
-		/* HT-460 small form factor production board */
-		n = "InfiniPath_HT-465";
-		break;
-	case 8:
-		n = "LS/X-1";
-		break;
-	case 9:		/* Comstock bringup test board */
-		n = "Comstock";
-		break;
-	case 10:
-		n = "OEM_Board_2";
-		break;
-	case 11:
-		n = "InfiniPath_HT-470";
-		break;
-	case 12:
-		n = "OEM_Board_4";
-		break;
-	default:		/* don't know, just print the number */
-		ipath_dev_err(dd, "Don't yet know about board "
-			      "with ID %u\n", boardrev);
-		snprintf(name, namelen, "Unknown_InfiniPath_HT-4xx_%u",
-			 boardrev);
-		break;
-	}
-	if (n)
-		snprintf(name, namelen, "%s", n);
-
-	if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 || dd->ipath_minrev > 3)) {
-		/*
-		 * This version of the driver only supports the HT-400
-		 * Rev 3.2
-		 */
-		ipath_dev_err(dd,
-			      "Unsupported HT-400 revision %u.%u!\n",
-			      dd->ipath_majrev, dd->ipath_minrev);
-		ret = 1;
-		goto bail;
-	}
-	/*
-	 * pkt/word counters are 32 bit, and therefore wrap fast enough
-	 * that we snapshot them from a timer, and maintain 64 bit shadow
-	 * copies
-	 */
-	dd->ipath_flags |= IPATH_32BITCOUNTERS;
-	if (dd->ipath_htspeed != 800)
-		ipath_dev_err(dd,
-			      "Incorrectly configured for HT @ %uMHz\n",
-			      dd->ipath_htspeed);
-	if (dd->ipath_boardrev == 7 || dd->ipath_boardrev == 11 ||
-	    dd->ipath_boardrev == 6)
-		dd->ipath_flags |= IPATH_GPIO_INTR;
-	else
-		dd->ipath_flags |= IPATH_POLL_RX_INTR;
-	if (dd->ipath_boardrev == 8) {	/* LS/X-1 */
-		u64 val;
-		val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-		if (val & INFINIPATH_EXTS_SERDESSEL) {
-			/*
-			 * hardware disabled
-			 *
-			 * This means that the chip is hardware disabled,
-			 * and will not be able to bring up the link,
-			 * in any case.  We special case this and abort
-			 * early, to avoid later messages.  We also set
-			 * the DISABLED status bit
-			 */
-			ipath_dbg("Unit %u is hardware-disabled\n",
-				  dd->ipath_unit);
-			*dd->ipath_statusp |= IPATH_STATUS_DISABLED;
-			/* this value is handled differently */
-			ret = 2;
-			goto bail;
-		}
-	}
-	ret = 0;
-
-bail:
-	return ret;
-}
-
-static void ipath_check_htlink(struct ipath_devdata *dd)
-{
-	u8 linkerr, link_off, i;
-
-	for (i = 0; i < 2; i++) {
-		link_off = dd->ipath_ht_slave_off + i * 4 + 0xd;
-		if (pci_read_config_byte(dd->pcidev, link_off, &linkerr))
-			dev_info(&dd->pcidev->dev, "Couldn't read "
-				 "linkerror%d of HT slave/primary block\n",
-				 i);
-		else if (linkerr & 0xf0) {
-			ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
-				   "clearing\n", linkerr >> 4, i);
-			/*
-			 * writing the linkerr bits that are set should
-			 * clear them
-			 */
-			if (pci_write_config_byte(dd->pcidev, link_off,
-						  linkerr))
-				ipath_dbg("Failed write to clear HT "
-					  "linkerror%d\n", i);
-			if (pci_read_config_byte(dd->pcidev, link_off,
-						 &linkerr))
-				dev_info(&dd->pcidev->dev,
-					 "Couldn't reread linkerror%d of "
-					 "HT slave/primary block\n", i);
-			else if (linkerr & 0xf0)
-				dev_info(&dd->pcidev->dev,
-					 "HT linkerror%d bits 0x%x "
-					 "couldn't be cleared\n",
-					 i, linkerr >> 4);
-		}
-	}
-}
-
-static int ipath_setup_ht_reset(struct ipath_devdata *dd)
-{
-	ipath_dbg("No reset possible for HT-400\n");
-	return 0;
-}
-
-#define HT_CAPABILITY_ID   0x08	/* HT capabilities not defined in kernel */
-#define HT_INTR_DISC_CONFIG  0x80	/* HT interrupt and discovery cap */
-#define HT_INTR_REG_INDEX    2	/* intconfig requires indirect accesses */
-
-/*
- * Bits 13-15 of command==0 is slave/primary block.  Clear any HT CRC
- * errors.  We only bother to do this at load time, because it's OK if
- * it happened before we were loaded (first time after boot/reset),
- * but any time after that, it's fatal anyway.  Also need to not check
- * for for upper byte errors if we are in 8 bit mode, so figure out
- * our width.  For now, at least, also complain if it's 8 bit.
- */
-static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
-			     int pos, u8 cap_type)
-{
-	u8 linkwidth = 0, linkerr, link_a_b_off, link_off;
-	u16 linkctrl = 0;
-	int i;
-
-	dd->ipath_ht_slave_off = pos;
-	/* command word, master_host bit */
-	/* master host || slave */
-	if ((cap_type >> 2) & 1)
-		link_a_b_off = 4;
-	else
-		link_a_b_off = 0;
-	ipath_cdbg(VERBOSE, "HT%u (Link %c) connected to processor\n",
-		   link_a_b_off ? 1 : 0,
-		   link_a_b_off ? 'B' : 'A');
-
-	link_a_b_off += pos;
-
-	/*
-	 * check both link control registers; clear both HT CRC sets if
-	 * necessary.
-	 */
-	for (i = 0; i < 2; i++) {
-		link_off = pos + i * 4 + 0x4;
-		if (pci_read_config_word(pdev, link_off, &linkctrl))
-			ipath_dev_err(dd, "Couldn't read HT link control%d "
-				      "register\n", i);
-		else if (linkctrl & (0xf << 8)) {
-			ipath_cdbg(VERBOSE, "Clear linkctrl%d CRC Error "
-				   "bits %x\n", i, linkctrl & (0xf << 8));
-			/*
-			 * now write them back to clear the error.
-			 */
-			pci_write_config_byte(pdev, link_off,
-					      linkctrl & (0xf << 8));
-		}
-	}
-
-	/*
-	 * As with HT CRC bits, same for protocol errors that might occur
-	 * during boot.
-	 */
-	for (i = 0; i < 2; i++) {
-		link_off = pos + i * 4 + 0xd;
-		if (pci_read_config_byte(pdev, link_off, &linkerr))
-			dev_info(&pdev->dev, "Couldn't read linkerror%d "
-				 "of HT slave/primary block\n", i);
-		else if (linkerr & 0xf0) {
-			ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
-				   "clearing\n", linkerr >> 4, i);
-			/*
-			 * writing the linkerr bits that are set will clear
-			 * them
-			 */
-			if (pci_write_config_byte
-			    (pdev, link_off, linkerr))
-				ipath_dbg("Failed write to clear HT "
-					  "linkerror%d\n", i);
-			if (pci_read_config_byte(pdev, link_off, &linkerr))
-				dev_info(&pdev->dev, "Couldn't reread "
-					 "linkerror%d of HT slave/primary "
-					 "block\n", i);
-			else if (linkerr & 0xf0)
-				dev_info(&pdev->dev, "HT linkerror%d bits "
-					 "0x%x couldn't be cleared\n",
-					 i, linkerr >> 4);
-		}
-	}
-
-	/*
-	 * this is just for our link to the host, not devices connected
-	 * through tunnel.
-	 */
-
-	if (pci_read_config_byte(pdev, link_a_b_off + 7, &linkwidth))
-		ipath_dev_err(dd, "Couldn't read HT link width "
-			      "config register\n");
-	else {
-		u32 width;
-		switch (linkwidth & 7) {
-		case 5:
-			width = 4;
-			break;
-		case 4:
-			width = 2;
-			break;
-		case 3:
-			width = 32;
-			break;
-		case 1:
-			width = 16;
-			break;
-		case 0:
-		default:	/* if wrong, assume 8 bit */
-			width = 8;
-			break;
-		}
-
-		dd->ipath_htwidth = width;
-
-		if (linkwidth != 0x11) {
-			ipath_dev_err(dd, "Not configured for 16 bit HT "
-				      "(%x)\n", linkwidth);
-			if (!(linkwidth & 0xf)) {
-				ipath_dbg("Will ignore HT lane1 errors\n");
-				dd->ipath_flags |= IPATH_8BIT_IN_HT0;
-			}
-		}
-	}
-
-	/*
-	 * this is just for our link to the host, not devices connected
-	 * through tunnel.
-	 */
-	if (pci_read_config_byte(pdev, link_a_b_off + 0xd, &linkwidth))
-		ipath_dev_err(dd, "Couldn't read HT link frequency "
-			      "config register\n");
-	else {
-		u32 speed;
-		switch (linkwidth & 0xf) {
-		case 6:
-			speed = 1000;
-			break;
-		case 5:
-			speed = 800;
-			break;
-		case 4:
-			speed = 600;
-			break;
-		case 3:
-			speed = 500;
-			break;
-		case 2:
-			speed = 400;
-			break;
-		case 1:
-			speed = 300;
-			break;
-		default:
-			/*
-			 * assume reserved and vendor-specific are 200...
-			 */
-		case 0:
-			speed = 200;
-			break;
-		}
-		dd->ipath_htspeed = speed;
-	}
-}
-
-static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
-			    int pos)
-{
-	u32 int_handler_addr_lower;
-	u32 int_handler_addr_upper;
-	u64 ihandler;
-	u32 intvec;
-
-	/* use indirection register to get the intr handler */
-	pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
-	pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
-	pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
-	pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
-
-	ihandler = (u64) int_handler_addr_lower |
-		((u64) int_handler_addr_upper << 32);
-
-	/*
-	 * kernels with CONFIG_PCI_MSI set the vector in the irq field of
-	 * struct pci_device, so we use that to program the HT-400 internal
-	 * interrupt register (not config space) with that value. The BIOS
-	 * must still have done the basic MSI setup.
-	 */
-	intvec = pdev->irq;
-	/*
-	 * clear any vector bits there; normally not set but we'll overload
-	 * this for some debug purposes (setting the HTC debug register
-	 * value from software, rather than GPIOs), so it might be set on a
-	 * driver reload.
-	 */
-	ihandler &= ~0xff0000;
-	/* x86 vector goes in intrinfo[23:16] */
-	ihandler |= intvec << 16;
-	ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
-		   "interruptconfig %llx\n", int_handler_addr_lower,
-		   int_handler_addr_upper, intvec,
-		   (unsigned long long) ihandler);
-
-	/* can't program yet, so save for interrupt setup */
-	dd->ipath_intconfig = ihandler;
-	/* keep going, so we find link control stuff also */
-
-	return ihandler != 0;
-}
-
-/**
- * ipath_setup_ht_config - setup the interruptconfig register
- * @dd: the infinipath device
- * @pdev: the PCI device
- *
- * setup the interruptconfig register from the HT config info.
- * Also clear CRC errors in HT linkcontrol, if necessary.
- * This is done only for the real hardware.  It is done before
- * chip address space is initted, so can't touch infinipath registers
- */
-static int ipath_setup_ht_config(struct ipath_devdata *dd,
-				 struct pci_dev *pdev)
-{
-	int pos, ret = 0;
-	int ihandler = 0;
-
-	/*
-	 * Read the capability info to find the interrupt info, and also
-	 * handle clearing CRC errors in linkctrl register if necessary.  We
-	 * do this early, before we ever enable errors or hardware errors,
-	 * mostly to avoid causing the chip to enter freeze mode.
-	 */
-	pos = pci_find_capability(pdev, HT_CAPABILITY_ID);
-	if (!pos) {
-		ipath_dev_err(dd, "Couldn't find HyperTransport "
-			      "capability; no interrupts\n");
-		ret = -ENODEV;
-		goto bail;
-	}
-	do {
-		u8 cap_type;
-
-		/* the HT capability type byte is 3 bytes after the
-		 * capability byte.
-		 */
-		if (pci_read_config_byte(pdev, pos + 3, &cap_type)) {
-			dev_info(&pdev->dev, "Couldn't read config "
-				 "command @ %d\n", pos);
-			continue;
-		}
-		if (!(cap_type & 0xE0))
-			slave_or_pri_blk(dd, pdev, pos, cap_type);
-		else if (cap_type == HT_INTR_DISC_CONFIG)
-			ihandler = set_int_handler(dd, pdev, pos);
-	} while ((pos = pci_find_next_capability(pdev, pos,
-						 HT_CAPABILITY_ID)));
-
-	if (!ihandler) {
-		ipath_dev_err(dd, "Couldn't find interrupt handler in "
-			      "config space\n");
-		ret = -ENODEV;
-	}
-
-bail:
-	return ret;
-}
-
-/**
- * ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff
- * @dd: the infinipath device
- *
- * Called during driver unload.
- * This is currently a nop for the HT-400, not for all chips
- */
-static void ipath_setup_ht_cleanup(struct ipath_devdata *dd)
-{
-}
-
-/**
- * ipath_setup_ht_setextled - set the state of the two external LEDs
- * @dd: the infinipath device
- * @lst: the L state
- * @ltst: the LT state
- *
- * Set the state of the two external LEDs, to indicate physical and
- * logical state of IB link.   For this chip (at least with recommended
- * board pinouts), LED1 is Green (physical state), and LED2 is Yellow
- * (logical state)
- *
- * Note:  We try to match the Mellanox HCA LED behavior as best
- * we can.  Green indicates physical link state is OK (something is
- * plugged in, and we can train).
- * Amber indicates the link is logically up (ACTIVE).
- * Mellanox further blinks the amber LED to indicate data packet
- * activity, but we have no hardware support for that, so it would
- * require waking up every 10-20 msecs and checking the counters
- * on the chip, and then turning the LED off if appropriate.  That's
- * visible overhead, so not something we will do.
- *
- */
-static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
-				     u64 lst, u64 ltst)
-{
-	u64 extctl;
-
-	/* the diags use the LED to indicate diag info, so we leave
-	 * the external LED alone when the diags are running */
-	if (ipath_diag_inuse)
-		return;
-
-	/*
-	 * start by setting both LED control bits to off, then turn
-	 * on the appropriate bit(s).
-	 */
-	if (dd->ipath_boardrev == 8) { /* LS/X-1 uses different pins */
-		/*
-		 * major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF
-		 * is inverted,  because it is normally used to indicate
-		 * a hardware fault at reset, if there were errors
-		 */
-		extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON)
-			| INFINIPATH_EXTC_LEDGBLERR_OFF;
-		if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
-			extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF;
-		if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
-			extctl |= INFINIPATH_EXTC_LEDGBLOK_ON;
-	}
-	else {
-		extctl = dd->ipath_extctrl &
-			~(INFINIPATH_EXTC_LED1PRIPORT_ON |
-			  INFINIPATH_EXTC_LED2PRIPORT_ON);
-		if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
-			extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
-		if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
-			extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
-	}
-	dd->ipath_extctrl = extctl;
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
-}
-
-static void ipath_init_ht_variables(void)
-{
-	ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
-	ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
-	ipath_gpio_sda = IPATH_GPIO_SDA;
-	ipath_gpio_scl = IPATH_GPIO_SCL;
-
-	infinipath_i_bitsextant =
-		(INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
-		(INFINIPATH_I_RCVAVAIL_MASK <<
-		 INFINIPATH_I_RCVAVAIL_SHIFT) |
-		INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
-		INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
-
-	infinipath_e_bitsextant =
-		INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
-		INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
-		INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
-		INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
-		INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
-		INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
-		INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
-		INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
-		INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
-		INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
-		INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
-		INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
-		INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
-		INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
-		INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
-		INFINIPATH_E_HARDWARE;
-
-	infinipath_hwe_bitsextant =
-		(INFINIPATH_HWE_HTCMEMPARITYERR_MASK <<
-		 INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) |
-		(INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
-		 INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
-		(INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
-		 INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
-		INFINIPATH_HWE_HTCLNKABYTE0CRCERR |
-		INFINIPATH_HWE_HTCLNKABYTE1CRCERR |
-		INFINIPATH_HWE_HTCLNKBBYTE0CRCERR |
-		INFINIPATH_HWE_HTCLNKBBYTE1CRCERR |
-		INFINIPATH_HWE_HTCMISCERR4 |
-		INFINIPATH_HWE_HTCMISCERR5 | INFINIPATH_HWE_HTCMISCERR6 |
-		INFINIPATH_HWE_HTCMISCERR7 |
-		INFINIPATH_HWE_HTCBUSTREQPARITYERR |
-		INFINIPATH_HWE_HTCBUSTRESPPARITYERR |
-		INFINIPATH_HWE_HTCBUSIREQPARITYERR |
-		INFINIPATH_HWE_RXDSYNCMEMPARITYERR |
-		INFINIPATH_HWE_MEMBISTFAILED |
-		INFINIPATH_HWE_COREPLL_FBSLIP |
-		INFINIPATH_HWE_COREPLL_RFSLIP |
-		INFINIPATH_HWE_HTBPLL_FBSLIP |
-		INFINIPATH_HWE_HTBPLL_RFSLIP |
-		INFINIPATH_HWE_HTAPLL_FBSLIP |
-		INFINIPATH_HWE_HTAPLL_RFSLIP |
-		INFINIPATH_HWE_SERDESPLLFAILED |
-		INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
-		INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
-
-	infinipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
-	infinipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
-}
-
-/**
- * ipath_ht_init_hwerrors - enable hardware errors
- * @dd: the infinipath device
- *
- * now that we have finished initializing everything that might reasonably
- * cause a hardware error, and cleared those errors bits as they occur,
- * we can enable hardware errors in the mask (potentially enabling
- * freeze mode), and enable hardware errors as errors (along with
- * everything else) in errormask
- */
-static void ipath_ht_init_hwerrors(struct ipath_devdata *dd)
-{
-	ipath_err_t val;
-	u64 extsval;
-
-	extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-
-	if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
-		ipath_dev_err(dd, "MemBIST did not complete!\n");
-
-	ipath_check_htlink(dd);
-
-	/* barring bugs, all hwerrors become interrupts, which can */
-	val = -1LL;
-	/* don't look at crc lane1 if 8 bit */
-	if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
-		val &= ~infinipath_hwe_htclnkabyte1crcerr;
-	/* don't look at crc lane1 if 8 bit */
-	if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
-		val &= ~infinipath_hwe_htclnkbbyte1crcerr;
-
-	/*
-	 * disable RXDSYNCMEMPARITY because external serdes is unused,
-	 * and therefore the logic will never be used or initialized,
-	 * and uninitialized state will normally result in this error
-	 * being asserted.  Similarly for the external serdess pll
-	 * lock signal.
-	 */
-	val &= ~(INFINIPATH_HWE_SERDESPLLFAILED |
-		 INFINIPATH_HWE_RXDSYNCMEMPARITYERR);
-
-	/*
-	 * Disable MISCERR4 because of an inversion in the HT core
-	 * logic checking for errors that cause this bit to be set.
-	 * The errata can also cause the protocol error bit to be set
-	 * in the HT config space linkerror register(s).
-	 */
-	val &= ~INFINIPATH_HWE_HTCMISCERR4;
-
-	/*
-	 * PLL ignored because MDIO interface has a logic problem
-	 * for reads, on Comstock and Ponderosa.  BRINGUP
-	 */
-	if (dd->ipath_boardrev == 4 || dd->ipath_boardrev == 9)
-		val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
-	dd->ipath_hwerrmask = val;
-}
-
-/**
- * ipath_ht_bringup_serdes - bring up the serdes
- * @dd: the infinipath device
- */
-static int ipath_ht_bringup_serdes(struct ipath_devdata *dd)
-{
-	u64 val, config1;
-	int ret = 0, change = 0;
-
-	ipath_dbg("Trying to bringup serdes\n");
-
-	if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
-	    INFINIPATH_HWE_SERDESPLLFAILED)
-	{
-		ipath_dbg("At start, serdes PLL failed bit set in "
-			  "hwerrstatus, clearing and continuing\n");
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
-				 INFINIPATH_HWE_SERDESPLLFAILED);
-	}
-
-	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-	config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
-
-	ipath_cdbg(VERBOSE, "Initial serdes status is config0=%llx "
-		   "config1=%llx, sstatus=%llx xgxs %llx\n",
-		   (unsigned long long) val, (unsigned long long) config1,
-		   (unsigned long long)
-		   ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
-		   (unsigned long long)
-		   ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
-	/* force reset on */
-	val |= INFINIPATH_SERDC0_RESET_PLL
-		/* | INFINIPATH_SERDC0_RESET_MASK */
-		;
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
-	udelay(15);		/* need pll reset set at least for a bit */
-
-	if (val & INFINIPATH_SERDC0_RESET_PLL) {
-		u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL;
-		/* set lane resets, and tx idle, during pll reset */
-		val2 |= INFINIPATH_SERDC0_RESET_MASK |
-			INFINIPATH_SERDC0_TXIDLE;
-		ipath_cdbg(VERBOSE, "Clearing serdes PLL reset (writing "
-			   "%llx)\n", (unsigned long long) val2);
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
-				 val2);
-		/*
-		 * be sure chip saw it
-		 */
-		val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
-		/*
-		 * need pll reset clear at least 11 usec before lane
-		 * resets cleared; give it a few more
-		 */
-		udelay(15);
-		val = val2;	/* for check below */
-	}
-
-	if (val & (INFINIPATH_SERDC0_RESET_PLL |
-		   INFINIPATH_SERDC0_RESET_MASK |
-		   INFINIPATH_SERDC0_TXIDLE)) {
-		val &= ~(INFINIPATH_SERDC0_RESET_PLL |
-			 INFINIPATH_SERDC0_RESET_MASK |
-			 INFINIPATH_SERDC0_TXIDLE);
-		/* clear them */
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
-				 val);
-	}
-
-	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
-	if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
-	     INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
-		val &= ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
-			 INFINIPATH_XGXS_MDIOADDR_SHIFT);
-		/*
-		 * we use address 3
-		 */
-		val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
-		change = 1;
-	}
-	if (val & INFINIPATH_XGXS_RESET) {
-		/* normally true after boot */
-		val &= ~INFINIPATH_XGXS_RESET;
-		change = 1;
-	}
-	if (change)
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
-
-	val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
-	/* clear current and de-emphasis bits */
-	config1 &= ~0x0ffffffff00ULL;
-	/* set current to 20ma */
-	config1 |= 0x00000000000ULL;
-	/* set de-emphasis to -5.68dB */
-	config1 |= 0x0cccc000000ULL;
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
-
-	ipath_cdbg(VERBOSE, "After setup: serdes status is config0=%llx "
-		   "config1=%llx, sstatus=%llx xgxs %llx\n",
-		   (unsigned long long) val, (unsigned long long) config1,
-		   (unsigned long long)
-		   ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
-		   (unsigned long long)
-		   ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
-	if (!ipath_waitfor_mdio_cmdready(dd)) {
-		ipath_write_kreg(dd, dd->ipath_kregs->kr_mdio,
-				 ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
-						IPATH_MDIO_CTRL_XGXS_REG_8,
-						0));
-		if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
-					   IPATH_MDIO_DATAVALID, &val))
-			ipath_dbg("Never got MDIO data for XGXS status "
-				  "read\n");
-		else
-			ipath_cdbg(VERBOSE, "MDIO Read reg8, "
-				   "'bank' 31 %x\n", (u32) val);
-	} else
-		ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
-
-	return ret;		/* for now, say we always succeeded */
-}
-
-/**
- * ipath_ht_quiet_serdes - set serdes to txidle
- * @dd: the infinipath device
- * driver is being unloaded
- */
-static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
-{
-	u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
-	val |= INFINIPATH_SERDC0_TXIDLE;
-	ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
-		  (unsigned long long) val);
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
-}
-
-static int ipath_ht_intconfig(struct ipath_devdata *dd)
-{
-	int ret;
-
-	if (!dd->ipath_intconfig) {
-		ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
-			      "interrupt address\n");
-		ret = 1;
-		goto bail;
-	}
-
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
-			 dd->ipath_intconfig);	/* interrupt address */
-	ret = 0;
-
-bail:
-	return ret;
-}
-
-/**
- * ipath_pe_put_tid - write a TID in chip
- * @dd: the infinipath device
- * @tidptr: pointer to the expected TID (in chip) to udpate
- * @tidtype: 0 for eager, 1 for expected
- * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
- *
- * This exists as a separate routine to allow for special locking etc.
- * It's used for both the full cleanup on exit, as well as the normal
- * setup and teardown.
- */
-static void ipath_ht_put_tid(struct ipath_devdata *dd,
-			     u64 __iomem *tidptr, u32 type,
-			     unsigned long pa)
-{
-	if (pa != dd->ipath_tidinvalid) {
-		if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) {
-			dev_info(&dd->pcidev->dev,
-				 "physaddr %lx has more than "
-				 "40 bits, using only 40!!!\n", pa);
-			pa &= INFINIPATH_RT_ADDR_MASK;
-		}
-		if (type == 0)
-			pa |= dd->ipath_tidtemplate;
-		else {
-			/* in words (fixed, full page).  */
-			u64 lenvalid = PAGE_SIZE >> 2;
-			lenvalid <<= INFINIPATH_RT_BUFSIZE_SHIFT;
-			pa |= lenvalid | INFINIPATH_RT_VALID;
-		}
-	}
-	if (dd->ipath_kregbase)
-		writeq(pa, tidptr);
-}
-
-/**
- * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager
- * @dd: the infinipath device
- * @port: the port
- *
- * Used from ipath_close(), and at chip initialization.
- */
-static void ipath_ht_clear_tids(struct ipath_devdata *dd, unsigned port)
-{
-	u64 __iomem *tidbase;
-	int i;
-
-	if (!dd->ipath_kregbase)
-		return;
-
-	ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
-
-	/*
-	 * need to invalidate all of the expected TID entries for this
-	 * port, so we don't have valid entries that might somehow get
-	 * used (early in next use of this port, or through some bug)
-	 */
-	tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
-				   dd->ipath_rcvtidbase +
-				   port * dd->ipath_rcvtidcnt *
-				   sizeof(*tidbase));
-	for (i = 0; i < dd->ipath_rcvtidcnt; i++)
-		ipath_ht_put_tid(dd, &tidbase[i], 1, dd->ipath_tidinvalid);
-
-	tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
-				   dd->ipath_rcvegrbase +
-				   port * dd->ipath_rcvegrcnt *
-				   sizeof(*tidbase));
-
-	for (i = 0; i < dd->ipath_rcvegrcnt; i++)
-		ipath_ht_put_tid(dd, &tidbase[i], 0, dd->ipath_tidinvalid);
-}
-
-/**
- * ipath_ht_tidtemplate - setup constants for TID updates
- * @dd: the infinipath device
- *
- * We setup stuff that we use a lot, to avoid calculating each time
- */
-static void ipath_ht_tidtemplate(struct ipath_devdata *dd)
-{
-	dd->ipath_tidtemplate = dd->ipath_ibmaxlen >> 2;
-	dd->ipath_tidtemplate <<= INFINIPATH_RT_BUFSIZE_SHIFT;
-	dd->ipath_tidtemplate |= INFINIPATH_RT_VALID;
-
-	/*
-	 * work around chip errata bug 7358, by marking invalid tids
-	 * as having max length
-	 */
-	dd->ipath_tidinvalid = (-1LL & INFINIPATH_RT_BUFSIZE_MASK) <<
-		INFINIPATH_RT_BUFSIZE_SHIFT;
-}
-
-static int ipath_ht_early_init(struct ipath_devdata *dd)
-{
-	u32 __iomem *piobuf;
-	u32 pioincr, val32, egrsize;
-	int i;
-
-	/*
-	 * one cache line; long IB headers will spill over into received
-	 * buffer
-	 */
-	dd->ipath_rcvhdrentsize = 16;
-	dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
-
-	/*
-	 * For HT-400, we allocate a somewhat overly large eager buffer,
-	 * such that we can guarantee that we can receive the largest
-	 * packet that we can send out.  To truly support a 4KB MTU,
-	 * we need to bump this to a large value.  To date, other than
-	 * testing, we have never encountered an HCA that can really
-	 * send 4KB MTU packets, so we do not handle that (we'll get
-	 * errors interrupts if we ever see one).
-	 */
-	dd->ipath_rcvegrbufsize = dd->ipath_piosize2k;
-	egrsize = dd->ipath_rcvegrbufsize;
-
-	/*
-	 * the min() check here is currently a nop, but it may not
-	 * always be, depending on just how we do ipath_rcvegrbufsize
-	 */
-	dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
-				 dd->ipath_rcvegrbufsize);
-	dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
-	ipath_ht_tidtemplate(dd);
-
-	/*
-	 * zero all the TID entries at startup.  We do this for sanity,
-	 * in case of a previous driver crash of some kind, and also
-	 * because the chip powers up with these memories in an unknown
-	 * state.  Use portcnt, not cfgports, since this is for the
-	 * full chip, not for current (possibly different) configuration
-	 * value.
-	 * Chip Errata bug 6447
-	 */
-	for (val32 = 0; val32 < dd->ipath_portcnt; val32++)
-		ipath_ht_clear_tids(dd, val32);
-
-	/*
-	 * write the pbc of each buffer, to be sure it's initialized, then
-	 * cancel all the buffers, and also abort any packets that might
-	 * have been in flight for some reason (the latter is for driver
-	 * unload/reload, but isn't a bad idea at first init).	PIO send
-	 * isn't enabled at this point, so there is no danger of sending
-	 * these out on the wire.
-	 * Chip Errata bug 6610
-	 */
-	piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) +
-				  dd->ipath_piobufbase);
-	pioincr = dd->ipath_palign / sizeof(*piobuf);
-	for (i = 0; i < dd->ipath_piobcnt2k; i++) {
-		/*
-		 * reasonable word count, just to init pbc
-		 */
-		writel(16, piobuf);
-		piobuf += pioincr;
-	}
-	/*
-	 * self-clearing
-	 */
-	ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
-			 INFINIPATH_S_ABORT);
-
-	ipath_get_eeprom_info(dd);
-	if(dd->ipath_boardrev == 5 && dd->ipath_serial[0] == '1' &&
-		dd->ipath_serial[1] == '2' && dd->ipath_serial[2] == '8') {
-		/*
-		 * Later production HT-460 has same changes as HT-465, so
-		 * can use GPIO interrupts.  They have serial #'s starting
-		 * with 128, rather than 112.
-		 */
-		dd->ipath_flags |= IPATH_GPIO_INTR;
-		dd->ipath_flags &= ~IPATH_POLL_RX_INTR;
-	}
-	return 0;
-}
-
-/**
- * ipath_init_ht_get_base_info - set chip-specific flags for user code
- * @dd: the infinipath device
- * @kbase: ipath_base_info pointer
- *
- * We set the PCIE flag because the lower bandwidth on PCIe vs
- * HyperTransport can affect some user packet algorithims.
- */
-static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
-{
-	struct ipath_base_info *kinfo = kbase;
-
-	kinfo->spi_runtime_flags |= IPATH_RUNTIME_HT |
-		IPATH_RUNTIME_RCVHDR_COPY;
-
-	return 0;
-}
-
-/**
- * ipath_init_ht400_funcs - set up the chip-specific function pointers
- * @dd: the infinipath device
- *
- * This is global, and is called directly at init to set up the
- * chip-specific function pointers for later use.
- */
-void ipath_init_ht400_funcs(struct ipath_devdata *dd)
-{
-	dd->ipath_f_intrsetup = ipath_ht_intconfig;
-	dd->ipath_f_bus = ipath_setup_ht_config;
-	dd->ipath_f_reset = ipath_setup_ht_reset;
-	dd->ipath_f_get_boardname = ipath_ht_boardname;
-	dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors;
-	dd->ipath_f_early_init = ipath_ht_early_init;
-	dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors;
-	dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes;
-	dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes;
-	dd->ipath_f_clear_tids = ipath_ht_clear_tids;
-	dd->ipath_f_put_tid = ipath_ht_put_tid;
-	dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
-	dd->ipath_f_setextled = ipath_setup_ht_setextled;
-	dd->ipath_f_get_base_info = ipath_ht_get_base_info;
-
-	/*
-	 * initialize chip-specific variables
-	 */
-	dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
-
-	/*
-	 * setup the register offsets, since they are different for each
-	 * chip
-	 */
-	dd->ipath_kregs = &ipath_ht_kregs;
-	dd->ipath_cregs = &ipath_ht_cregs;
-
-	/*
-	 * do very early init that is needed before ipath_f_bus is
-	 * called
-	 */
-	ipath_init_ht_variables();
-}