Input: add support for TI Touchscreen controller

This patch adds support for TI's touchscreen
controller for a 4/5/8 wire resistive panel
that is directly fed to the ADC.

This touchscreen controller will be part of
AM335x TI SoC. The TRM can be found at:
http://www.ti.com/lit/ug/spruh73a/spruh73a.pdf

Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

3 files changed, 499 insertions, 0 deletions

diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 2b21a7066d3..5df719b591c 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -460,6 +460,18 @@ config TOUCHSCREEN_TOUCHWIN
 	  To compile this driver as a module, choose M here: the
 	  module will be called touchwin.
 
+config TOUCHSCREEN_TI_TSCADC
+	tristate "TI Touchscreen Interface"
+	depends on ARCH_OMAP2PLUS
+	help
+	  Say Y here if you have 4/5/8 wire touchscreen controller
+	  to be connected to the ADC controller on your TI AM335x SoC.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti_tscadc.
+
 config TOUCHSCREEN_ATMEL_TSADCC
 	tristate "Atmel Touchscreen Interface"
 	depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index d9acbdcda3d..e748fb83775 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_TOUCHSCREEN_PIXCIR)	+= pixcir_i2c_ts.o
 obj-$(CONFIG_TOUCHSCREEN_S3C2410)	+= s3c2410_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ST1232)	+= st1232.o
 obj-$(CONFIG_TOUCHSCREEN_STMPE)		+= stmpe-ts.o
+obj-$(CONFIG_TOUCHSCREEN_TI_TSCADC)	+= ti_tscadc.o
 obj-$(CONFIG_TOUCHSCREEN_TNETV107X)	+= tnetv107x-ts.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
diff --git a/drivers/input/touchscreen/ti_tscadc.c b/drivers/input/touchscreen/ti_tscadc.c
new file mode 100644
index 00000000000..d229c741d54
--- /dev/null
+++ b/drivers/input/touchscreen/ti_tscadc.c
@@ -0,0 +1,486 @@
+/*
+ * TI Touch Screen driver
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/input/ti_tscadc.h>
+#include <linux/delay.h>
+
+#define REG_IRQEOI		0x020
+#define REG_RAWIRQSTATUS	0x024
+#define REG_IRQSTATUS		0x028
+#define REG_IRQENABLE		0x02C
+#define REG_IRQWAKEUP		0x034
+#define REG_CTRL		0x040
+#define REG_ADCFSM		0x044
+#define REG_CLKDIV		0x04C
+#define REG_SE			0x054
+#define REG_IDLECONFIG		0x058
+#define REG_CHARGECONFIG	0x05C
+#define REG_CHARGEDELAY		0x060
+#define REG_STEPCONFIG(n)	(0x64 + ((n - 1) * 8))
+#define REG_STEPDELAY(n)	(0x68 + ((n - 1) * 8))
+#define REG_STEPCONFIG13	0x0C4
+#define REG_STEPDELAY13		0x0C8
+#define REG_STEPCONFIG14	0x0CC
+#define REG_STEPDELAY14		0x0D0
+#define REG_FIFO0CNT		0xE4
+#define REG_FIFO1THR		0xF4
+#define REG_FIFO0		0x100
+#define REG_FIFO1		0x200
+
+/*	Register Bitfields	*/
+#define IRQWKUP_ENB		BIT(0)
+#define STPENB_STEPENB		0x7FFF
+#define IRQENB_FIFO1THRES	BIT(5)
+#define IRQENB_PENUP		BIT(9)
+#define STEPCONFIG_MODE_HWSYNC	0x2
+#define STEPCONFIG_SAMPLES_AVG	(1 << 4)
+#define STEPCONFIG_XPP		(1 << 5)
+#define STEPCONFIG_XNN		(1 << 6)
+#define STEPCONFIG_YPP		(1 << 7)
+#define STEPCONFIG_YNN		(1 << 8)
+#define STEPCONFIG_XNP		(1 << 9)
+#define STEPCONFIG_YPN		(1 << 10)
+#define STEPCONFIG_INM		(1 << 18)
+#define STEPCONFIG_INP		(1 << 20)
+#define STEPCONFIG_INP_5	(1 << 21)
+#define STEPCONFIG_FIFO1	(1 << 26)
+#define STEPCONFIG_OPENDLY	0xff
+#define STEPCONFIG_Z1		(3 << 19)
+#define STEPIDLE_INP		(1 << 22)
+#define STEPCHARGE_RFP		(1 << 12)
+#define STEPCHARGE_INM		(1 << 15)
+#define STEPCHARGE_INP		(1 << 19)
+#define STEPCHARGE_RFM		(1 << 23)
+#define STEPCHARGE_DELAY	0x1
+#define CNTRLREG_TSCSSENB	(1 << 0)
+#define CNTRLREG_STEPID		(1 << 1)
+#define CNTRLREG_STEPCONFIGWRT	(1 << 2)
+#define CNTRLREG_4WIRE		(1 << 5)
+#define CNTRLREG_5WIRE		(1 << 6)
+#define CNTRLREG_8WIRE		(3 << 5)
+#define CNTRLREG_TSCENB		(1 << 7)
+#define ADCFSM_STEPID		0x10
+
+#define SEQ_SETTLE		275
+#define ADC_CLK			3000000
+#define MAX_12BIT		((1 << 12) - 1)
+#define TSCADC_DELTA_X		15
+#define TSCADC_DELTA_Y		15
+
+struct tscadc {
+	struct input_dev	*input;
+	struct clk		*tsc_ick;
+	void __iomem		*tsc_base;
+	unsigned int		irq;
+	unsigned int		wires;
+	unsigned int		x_plate_resistance;
+	bool			pen_down;
+};
+
+static unsigned int tscadc_readl(struct tscadc *ts, unsigned int reg)
+{
+	return readl(ts->tsc_base + reg);
+}
+
+static void tscadc_writel(struct tscadc *tsc, unsigned int reg,
+					unsigned int val)
+{
+	writel(val, tsc->tsc_base + reg);
+}
+
+static void tscadc_step_config(struct tscadc *ts_dev)
+{
+	unsigned int	config;
+	int i;
+
+	/* Configure the Step registers */
+
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_XPP;
+	switch (ts_dev->wires) {
+	case 4:
+		config |= STEPCONFIG_INP | STEPCONFIG_XNN;
+		break;
+	case 5:
+		config |= STEPCONFIG_YNN |
+				STEPCONFIG_INP_5 | STEPCONFIG_XNN |
+				STEPCONFIG_YPP;
+		break;
+	case 8:
+		config |= STEPCONFIG_INP | STEPCONFIG_XNN;
+		break;
+	}
+
+	for (i = 1; i < 7; i++) {
+		tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
+		tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+	}
+
+	config = 0;
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_YNN |
+			STEPCONFIG_INM | STEPCONFIG_FIFO1;
+	switch (ts_dev->wires) {
+	case 4:
+		config |= STEPCONFIG_YPP;
+		break;
+	case 5:
+		config |= STEPCONFIG_XPP | STEPCONFIG_INP_5 |
+				STEPCONFIG_XNP | STEPCONFIG_YPN;
+		break;
+	case 8:
+		config |= STEPCONFIG_YPP;
+		break;
+	}
+
+	for (i = 7; i < 13; i++) {
+		tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
+		tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+	}
+
+	config = 0;
+	/* Charge step configuration */
+	config = STEPCONFIG_XPP | STEPCONFIG_YNN |
+			STEPCHARGE_RFP | STEPCHARGE_RFM |
+			STEPCHARGE_INM | STEPCHARGE_INP;
+
+	tscadc_writel(ts_dev, REG_CHARGECONFIG, config);
+	tscadc_writel(ts_dev, REG_CHARGEDELAY, STEPCHARGE_DELAY);
+
+	config = 0;
+	/* Configure to calculate pressure */
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_YPP |
+			STEPCONFIG_XNN | STEPCONFIG_INM;
+	tscadc_writel(ts_dev, REG_STEPCONFIG13, config);
+	tscadc_writel(ts_dev, REG_STEPDELAY13, STEPCONFIG_OPENDLY);
+
+	config |= STEPCONFIG_Z1 | STEPCONFIG_FIFO1;
+	tscadc_writel(ts_dev, REG_STEPCONFIG14, config);
+	tscadc_writel(ts_dev, REG_STEPDELAY14, STEPCONFIG_OPENDLY);
+
+	tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+}
+
+static void tscadc_idle_config(struct tscadc *ts_config)
+{
+	unsigned int idleconfig;
+
+	idleconfig = STEPCONFIG_YNN |
+			STEPCONFIG_INM |
+			STEPCONFIG_YPN | STEPIDLE_INP;
+	tscadc_writel(ts_config, REG_IDLECONFIG, idleconfig);
+}
+
+static void tscadc_read_coordinates(struct tscadc *ts_dev,
+				    unsigned int *x, unsigned int *y)
+{
+	unsigned int fifocount = tscadc_readl(ts_dev, REG_FIFO0CNT);
+	unsigned int prev_val_x = ~0, prev_val_y = ~0;
+	unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
+	unsigned int read, diff;
+	unsigned int i;
+
+	/*
+	 * Delta filter is used to remove large variations in sampled
+	 * values from ADC. The filter tries to predict where the next
+	 * coordinate could be. This is done by taking a previous
+	 * coordinate and subtracting it form current one. Further the
+	 * algorithm compares the difference with that of a present value,
+	 * if true the value is reported to the sub system.
+	 */
+	for (i = 0; i < fifocount - 1; i++) {
+		read = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
+		diff = abs(read - prev_val_x);
+		if (diff < prev_diff_x) {
+			prev_diff_x = diff;
+			*x = read;
+		}
+		prev_val_x = read;
+
+		read = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+		diff = abs(read - prev_val_y);
+		if (diff < prev_diff_y) {
+			prev_diff_y = diff;
+			*y = read;
+		}
+		prev_val_y = read;
+	}
+}
+
+static irqreturn_t tscadc_irq(int irq, void *dev)
+{
+	struct tscadc *ts_dev = dev;
+	struct input_dev *input_dev = ts_dev->input;
+	unsigned int status, irqclr = 0;
+	unsigned int x = 0, y = 0;
+	unsigned int z1, z2, z;
+	unsigned int fsm;
+
+	status = tscadc_readl(ts_dev, REG_IRQSTATUS);
+	if (status & IRQENB_FIFO1THRES) {
+		tscadc_read_coordinates(ts_dev, &x, &y);
+
+		z1 = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
+		z2 = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
+
+		if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
+			/*
+			 * Calculate pressure using formula
+			 * Resistance(touch) = x plate resistance *
+			 * x postion/4096 * ((z2 / z1) - 1)
+			 */
+			z = z2 - z1;
+			z *= x;
+			z *= ts_dev->x_plate_resistance;
+			z /= z1;
+			z = (z + 2047) >> 12;
+
+			if (z <= MAX_12BIT) {
+				input_report_abs(input_dev, ABS_X, x);
+				input_report_abs(input_dev, ABS_Y, y);
+				input_report_abs(input_dev, ABS_PRESSURE, z);
+				input_report_key(input_dev, BTN_TOUCH, 1);
+				input_sync(input_dev);
+			}
+		}
+		irqclr |= IRQENB_FIFO1THRES;
+	}
+
+	/*
+	 * Time for sequencer to settle, to read
+	 * correct state of the sequencer.
+	 */
+	udelay(SEQ_SETTLE);
+
+	status = tscadc_readl(ts_dev, REG_RAWIRQSTATUS);
+	if (status & IRQENB_PENUP) {
+		/* Pen up event */
+		fsm = tscadc_readl(ts_dev, REG_ADCFSM);
+		if (fsm == ADCFSM_STEPID) {
+			ts_dev->pen_down = false;
+			input_report_key(input_dev, BTN_TOUCH, 0);
+			input_report_abs(input_dev, ABS_PRESSURE, 0);
+			input_sync(input_dev);
+		} else {
+			ts_dev->pen_down = true;
+		}
+		irqclr |= IRQENB_PENUP;
+	}
+
+	tscadc_writel(ts_dev, REG_IRQSTATUS, irqclr);
+	/* check pending interrupts */
+	tscadc_writel(ts_dev, REG_IRQEOI, 0x0);
+
+	tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
+	return IRQ_HANDLED;
+}
+
+/*
+ * The functions for inserting/removing driver as a module.
+ */
+
+static int __devinit tscadc_probe(struct platform_device *pdev)
+{
+	const struct tsc_data *pdata = pdev->dev.platform_data;
+	struct resource *res;
+	struct tscadc *ts_dev;
+	struct input_dev *input_dev;
+	struct clk *clk;
+	int err;
+	int clk_value, ctrl, irq;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "missing platform data.\n");
+		return -EINVAL;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "no memory resource defined.\n");
+		return -EINVAL;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "no irq ID is specified.\n");
+		return -EINVAL;
+	}
+
+	/* Allocate memory for device */
+	ts_dev = kzalloc(sizeof(struct tscadc), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!ts_dev || !input_dev) {
+		dev_err(&pdev->dev, "failed to allocate memory.\n");
+		err = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	ts_dev->input = input_dev;
+	ts_dev->irq = irq;
+	ts_dev->wires = pdata->wires;
+	ts_dev->x_plate_resistance = pdata->x_plate_resistance;
+
+	res = request_mem_region(res->start, resource_size(res), pdev->name);
+	if (!res) {
+		dev_err(&pdev->dev, "failed to reserve registers.\n");
+		err = -EBUSY;
+		goto err_free_mem;
+	}
+
+	ts_dev->tsc_base = ioremap(res->start, resource_size(res));
+	if (!ts_dev->tsc_base) {
+		dev_err(&pdev->dev, "failed to map registers.\n");
+		err = -ENOMEM;
+		goto err_release_mem_region;
+	}
+
+	err = request_irq(ts_dev->irq, tscadc_irq,
+			  0, pdev->dev.driver->name, ts_dev);
+	if (err) {
+		dev_err(&pdev->dev, "failed to allocate irq.\n");
+		goto err_unmap_regs;
+	}
+
+	ts_dev->tsc_ick = clk_get(&pdev->dev, "adc_tsc_ick");
+	if (IS_ERR(ts_dev->tsc_ick)) {
+		dev_err(&pdev->dev, "failed to get TSC ick\n");
+		goto err_free_irq;
+	}
+	clk_enable(ts_dev->tsc_ick);
+
+	clk = clk_get(&pdev->dev, "adc_tsc_fck");
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed to get TSC fck\n");
+		err = PTR_ERR(clk);
+		goto err_disable_clk;
+	}
+
+	clk_value = clk_get_rate(clk) / ADC_CLK;
+	clk_put(clk);
+
+	if (clk_value < 7) {
+		dev_err(&pdev->dev, "clock input less than min clock requirement\n");
+		goto err_disable_clk;
+	}
+	/* CLKDIV needs to be configured to the value minus 1 */
+	tscadc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
+
+	 /* Enable wake-up of the SoC using touchscreen */
+	tscadc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+
+	ctrl = CNTRLREG_STEPCONFIGWRT |
+			CNTRLREG_TSCENB |
+			CNTRLREG_STEPID;
+	switch (ts_dev->wires) {
+	case 4:
+		ctrl |= CNTRLREG_4WIRE;
+		break;
+	case 5:
+		ctrl |= CNTRLREG_5WIRE;
+		break;
+	case 8:
+		ctrl |= CNTRLREG_8WIRE;
+		break;
+	}
+	tscadc_writel(ts_dev, REG_CTRL, ctrl);
+
+	tscadc_idle_config(ts_dev);
+	tscadc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO1THRES);
+	tscadc_step_config(ts_dev);
+	tscadc_writel(ts_dev, REG_FIFO1THR, 6);
+
+	ctrl |= CNTRLREG_TSCSSENB;
+	tscadc_writel(ts_dev, REG_CTRL, ctrl);
+
+	input_dev->name = "ti-tsc-adc";
+	input_dev->dev.parent = &pdev->dev;
+
+	input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+	input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+
+	input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(input_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
+
+	/* register to the input system */
+	err = input_register_device(input_dev);
+	if (err)
+		goto err_disable_clk;
+
+	platform_set_drvdata(pdev, ts_dev);
+	return 0;
+
+err_disable_clk:
+	clk_disable(ts_dev->tsc_ick);
+	clk_put(ts_dev->tsc_ick);
+err_free_irq:
+	free_irq(ts_dev->irq, ts_dev);
+err_unmap_regs:
+	iounmap(ts_dev->tsc_base);
+err_release_mem_region:
+	release_mem_region(res->start, resource_size(res));
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(ts_dev);
+	return err;
+}
+
+static int __devexit tscadc_remove(struct platform_device *pdev)
+{
+	struct tscadc *ts_dev = platform_get_drvdata(pdev);
+	struct resource *res;
+
+	free_irq(ts_dev->irq, ts_dev);
+
+	input_unregister_device(ts_dev->input);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	iounmap(ts_dev->tsc_base);
+	release_mem_region(res->start, resource_size(res));
+
+	clk_disable(ts_dev->tsc_ick);
+	clk_put(ts_dev->tsc_ick);
+
+	kfree(ts_dev);
+
+	platform_set_drvdata(pdev, NULL);
+	return 0;
+}
+
+static struct platform_driver ti_tsc_driver = {
+	.probe	= tscadc_probe,
+	.remove	= __devexit_p(tscadc_remove),
+	.driver	= {
+		.name   = "tsc",
+		.owner	= THIS_MODULE,
+	},
+};
+module_platform_driver(ti_tsc_driver);
+
+MODULE_DESCRIPTION("TI touchscreen controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");