Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull part one of ARM SoC updates from Olof Johansson:
 "A quite large set of SoC updates this cycle.  In no particular order:

   - Multi-cluster power management for Samsung Exynos, adding support
     for big.LITTLE CPU switching on EXYNOS5

   - SMP support for Marvell Armada 375 and 38x

   - SMP rework on Allwinner A31

   - Xilinx Zynq support for SOC_BUS, big endian

   - Marvell orion5x platform cleanup, modernizing the implementation
     and moving to DT.

   - _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
     that their platform can be enabled in the same kernel binary as
     most of the other v7 platforms in the tree.  \o/

     The work isn't quite complete, there's some driver fixes still
     needed, but the basics now work.

  New SoC support added:

   - Freescale i.MX6SX

   - LSI Axxia AXM55xx SoCs

   - Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800

   - STi STIH407

  plus a large set of various smaller updates for different platforms.
  I'm probably missing some important one here"

* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
  ARM: exynos: don't run exynos4 l2x0 setup on other platforms
  ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
  ARM: EXYNOS: mcpm rename the power_down_finish
  ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
  ARM: EXYNOS: Enable multi-platform build support
  ARM: EXYNOS: Consolidate Kconfig entries
  ARM: EXYNOS: Add support for EXYNOS5410 SoC
  ARM: EXYNOS: Support secondary CPU boot of Exynos3250
  ARM: EXYNOS: Add Exynos3250 SoC ID
  ARM: EXYNOS: Add 5800 SoC support
  ARM: EXYNOS: initial board support for exynos5260 SoC
  clk: exynos5410: register clocks using common clock framework
  ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
  ARM: sunxi: allow building without reset controller
  Documentation: devicetree: arm: sort enable-method entries
  ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
  clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
  ARM: dts: axxia: Add reset controller
  power: reset: Add Axxia system reset driver
  ARM: axxia: Adding defconfig for AXM55xx
  ...

3 files changed, 0 insertions, 371 deletions

diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index b845e937087..d4e5ab57909 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -550,18 +550,6 @@ config TOUCHSCREEN_TI_AM335X_TSC
 	  To compile this driver as a module, choose M here: the
 	  module will be called ti_am335x_tsc.
 
-config TOUCHSCREEN_ATMEL_TSADCC
-	tristate "Atmel Touchscreen Interface"
-	depends on ARCH_AT91
-	help
-	  Say Y here if you have a 4-wire touchscreen connected to the
-          ADC Controller on your Atmel SoC.
-
-	  If unsure, say N.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called atmel_tsadcc.
-
 config TOUCHSCREEN_UCB1400
 	tristate "Philips UCB1400 touchscreen"
 	depends on AC97_BUS
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 4bc954b7c7c..03f12a1f221 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -13,7 +13,6 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_I2C)	+= ad7879-i2c.o
 obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI)	+= ad7879-spi.o
 obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
 obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT)	+= atmel_mxt_ts.o
-obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC)	+= atmel_tsadcc.o
 obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR)	+= auo-pixcir-ts.o
 obj-$(CONFIG_TOUCHSCREEN_BU21013)	+= bu21013_ts.o
 obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110)	+= cy8ctmg110_ts.o
diff --git a/drivers/input/touchscreen/atmel_tsadcc.c b/drivers/input/touchscreen/atmel_tsadcc.c
deleted file mode 100644
index a7c9d6967d1..00000000000
--- a/drivers/input/touchscreen/atmel_tsadcc.c
+++ /dev/null
@@ -1,358 +0,0 @@
-/*
- *  Atmel Touch Screen Driver
- *
- *  Copyright (c) 2008 ATMEL
- *  Copyright (c) 2008 Dan Liang
- *  Copyright (c) 2008 TimeSys Corporation
- *  Copyright (c) 2008 Justin Waters
- *
- *  Based on touchscreen code from Atmel Corporation.
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License version 2 as
- *  published by the Free Software Foundation.
- */
-#include <linux/err.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/input.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/atmel.h>
-#include <mach/cpu.h>
-
-/* Register definitions based on AT91SAM9RL64 preliminary draft datasheet */
-
-#define ATMEL_TSADCC_CR		0x00	/* Control register */
-#define   ATMEL_TSADCC_SWRST	(1 << 0)	/* Software Reset*/
-#define	  ATMEL_TSADCC_START	(1 << 1)	/* Start conversion */
-
-#define ATMEL_TSADCC_MR		0x04	/* Mode register */
-#define	  ATMEL_TSADCC_TSAMOD	(3    <<  0)	/* ADC mode */
-#define	    ATMEL_TSADCC_TSAMOD_ADC_ONLY_MODE	(0x0)	/* ADC Mode */
-#define	    ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE	(0x1)	/* Touch Screen Only Mode */
-#define	  ATMEL_TSADCC_LOWRES	(1    <<  4)	/* Resolution selection */
-#define	  ATMEL_TSADCC_SLEEP	(1    <<  5)	/* Sleep mode */
-#define	  ATMEL_TSADCC_PENDET	(1    <<  6)	/* Pen Detect selection */
-#define	  ATMEL_TSADCC_PRES	(1    <<  7)	/* Pressure Measurement Selection */
-#define	  ATMEL_TSADCC_PRESCAL	(0x3f <<  8)	/* Prescalar Rate Selection */
-#define	  ATMEL_TSADCC_EPRESCAL	(0xff <<  8)	/* Prescalar Rate Selection (Extended) */
-#define	  ATMEL_TSADCC_STARTUP	(0x7f << 16)	/* Start Up time */
-#define	  ATMEL_TSADCC_SHTIM	(0xf  << 24)	/* Sample & Hold time */
-#define	  ATMEL_TSADCC_PENDBC	(0xf  << 28)	/* Pen Detect debouncing time */
-
-#define ATMEL_TSADCC_TRGR	0x08	/* Trigger register */
-#define	  ATMEL_TSADCC_TRGMOD	(7      <<  0)	/* Trigger mode */
-#define	    ATMEL_TSADCC_TRGMOD_NONE		(0 << 0)
-#define     ATMEL_TSADCC_TRGMOD_EXT_RISING	(1 << 0)
-#define     ATMEL_TSADCC_TRGMOD_EXT_FALLING	(2 << 0)
-#define     ATMEL_TSADCC_TRGMOD_EXT_ANY		(3 << 0)
-#define     ATMEL_TSADCC_TRGMOD_PENDET		(4 << 0)
-#define     ATMEL_TSADCC_TRGMOD_PERIOD		(5 << 0)
-#define     ATMEL_TSADCC_TRGMOD_CONTINUOUS	(6 << 0)
-#define   ATMEL_TSADCC_TRGPER	(0xffff << 16)	/* Trigger period */
-
-#define ATMEL_TSADCC_TSR	0x0C	/* Touch Screen register */
-#define	  ATMEL_TSADCC_TSFREQ	(0xf <<  0)	/* TS Frequency in Interleaved mode */
-#define	  ATMEL_TSADCC_TSSHTIM	(0xf << 24)	/* Sample & Hold time */
-
-#define ATMEL_TSADCC_CHER	0x10	/* Channel Enable register */
-#define ATMEL_TSADCC_CHDR	0x14	/* Channel Disable register */
-#define ATMEL_TSADCC_CHSR	0x18	/* Channel Status register */
-#define	  ATMEL_TSADCC_CH(n)	(1 << (n))	/* Channel number */
-
-#define ATMEL_TSADCC_SR		0x1C	/* Status register */
-#define	  ATMEL_TSADCC_EOC(n)	(1 << ((n)+0))	/* End of conversion for channel N */
-#define	  ATMEL_TSADCC_OVRE(n)	(1 << ((n)+8))	/* Overrun error for channel N */
-#define	  ATMEL_TSADCC_DRDY	(1 << 16)	/* Data Ready */
-#define	  ATMEL_TSADCC_GOVRE	(1 << 17)	/* General Overrun Error */
-#define	  ATMEL_TSADCC_ENDRX	(1 << 18)	/* End of RX Buffer */
-#define	  ATMEL_TSADCC_RXBUFF	(1 << 19)	/* TX Buffer full */
-#define	  ATMEL_TSADCC_PENCNT	(1 << 20)	/* Pen contact */
-#define	  ATMEL_TSADCC_NOCNT	(1 << 21)	/* No contact */
-
-#define ATMEL_TSADCC_LCDR	0x20	/* Last Converted Data register */
-#define	  ATMEL_TSADCC_DATA	(0x3ff << 0)	/* Channel data */
-
-#define ATMEL_TSADCC_IER	0x24	/* Interrupt Enable register */
-#define ATMEL_TSADCC_IDR	0x28	/* Interrupt Disable register */
-#define ATMEL_TSADCC_IMR	0x2C	/* Interrupt Mask register */
-#define ATMEL_TSADCC_CDR0	0x30	/* Channel Data 0 */
-#define ATMEL_TSADCC_CDR1	0x34	/* Channel Data 1 */
-#define ATMEL_TSADCC_CDR2	0x38	/* Channel Data 2 */
-#define ATMEL_TSADCC_CDR3	0x3C	/* Channel Data 3 */
-#define ATMEL_TSADCC_CDR4	0x40	/* Channel Data 4 */
-#define ATMEL_TSADCC_CDR5	0x44	/* Channel Data 5 */
-
-#define ATMEL_TSADCC_XPOS	0x50
-#define ATMEL_TSADCC_Z1DAT	0x54
-#define ATMEL_TSADCC_Z2DAT	0x58
-
-#define PRESCALER_VAL(x)	((x) >> 8)
-
-#define ADC_DEFAULT_CLOCK	100000
-
-struct atmel_tsadcc {
-	struct input_dev	*input;
-	char			phys[32];
-	struct clk		*clk;
-	int			irq;
-	unsigned int		prev_absx;
-	unsigned int		prev_absy;
-	unsigned char		bufferedmeasure;
-};
-
-static void __iomem		*tsc_base;
-
-#define atmel_tsadcc_read(reg)		__raw_readl(tsc_base + (reg))
-#define atmel_tsadcc_write(reg, val)	__raw_writel((val), tsc_base + (reg))
-
-static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)
-{
-	struct atmel_tsadcc	*ts_dev = (struct atmel_tsadcc *)dev;
-	struct input_dev	*input_dev = ts_dev->input;
-
-	unsigned int status;
-	unsigned int reg;
-
-	status = atmel_tsadcc_read(ATMEL_TSADCC_SR);
-	status &= atmel_tsadcc_read(ATMEL_TSADCC_IMR);
-
-	if (status & ATMEL_TSADCC_NOCNT) {
-		/* Contact lost */
-		reg = atmel_tsadcc_read(ATMEL_TSADCC_MR) | ATMEL_TSADCC_PENDBC;
-
-		atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
-		atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
-		atmel_tsadcc_write(ATMEL_TSADCC_IDR,
-				   ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
-		atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
-
-		input_report_key(input_dev, BTN_TOUCH, 0);
-		ts_dev->bufferedmeasure = 0;
-		input_sync(input_dev);
-
-	} else if (status & ATMEL_TSADCC_PENCNT) {
-		/* Pen detected */
-		reg = atmel_tsadcc_read(ATMEL_TSADCC_MR);
-		reg &= ~ATMEL_TSADCC_PENDBC;
-
-		atmel_tsadcc_write(ATMEL_TSADCC_IDR, ATMEL_TSADCC_PENCNT);
-		atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
-		atmel_tsadcc_write(ATMEL_TSADCC_IER,
-				   ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
-		atmel_tsadcc_write(ATMEL_TSADCC_TRGR,
-				   ATMEL_TSADCC_TRGMOD_PERIOD | (0x0FFF << 16));
-
-	} else if (status & ATMEL_TSADCC_EOC(3)) {
-		/* Conversion finished */
-
-		if (ts_dev->bufferedmeasure) {
-			/* Last measurement is always discarded, since it can
-			 * be erroneous.
-			 * Always report previous measurement */
-			input_report_abs(input_dev, ABS_X, ts_dev->prev_absx);
-			input_report_abs(input_dev, ABS_Y, ts_dev->prev_absy);
-			input_report_key(input_dev, BTN_TOUCH, 1);
-			input_sync(input_dev);
-		} else
-			ts_dev->bufferedmeasure = 1;
-
-		/* Now make new measurement */
-		ts_dev->prev_absx = atmel_tsadcc_read(ATMEL_TSADCC_CDR3) << 10;
-		ts_dev->prev_absx /= atmel_tsadcc_read(ATMEL_TSADCC_CDR2);
-
-		ts_dev->prev_absy = atmel_tsadcc_read(ATMEL_TSADCC_CDR1) << 10;
-		ts_dev->prev_absy /= atmel_tsadcc_read(ATMEL_TSADCC_CDR0);
-	}
-
-	return IRQ_HANDLED;
-}
-
-/*
- * The functions for inserting/removing us as a module.
- */
-
-static int atmel_tsadcc_probe(struct platform_device *pdev)
-{
-	struct atmel_tsadcc	*ts_dev;
-	struct input_dev	*input_dev;
-	struct resource		*res;
-	struct at91_tsadcc_data *pdata = dev_get_platdata(&pdev->dev);
-	int		err;
-	unsigned int	prsc;
-	unsigned int	reg;
-
-	if (!pdata)
-		return -EINVAL;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "no mmio resource defined.\n");
-		return -ENXIO;
-	}
-
-	/* Allocate memory for device */
-	ts_dev = kzalloc(sizeof(struct atmel_tsadcc), GFP_KERNEL);
-	if (!ts_dev) {
-		dev_err(&pdev->dev, "failed to allocate memory.\n");
-		return -ENOMEM;
-	}
-	platform_set_drvdata(pdev, ts_dev);
-
-	input_dev = input_allocate_device();
-	if (!input_dev) {
-		dev_err(&pdev->dev, "failed to allocate input device.\n");
-		err = -EBUSY;
-		goto err_free_mem;
-	}
-
-	ts_dev->irq = platform_get_irq(pdev, 0);
-	if (ts_dev->irq < 0) {
-		dev_err(&pdev->dev, "no irq ID is designated.\n");
-		err = -ENODEV;
-		goto err_free_dev;
-	}
-
-	if (!request_mem_region(res->start, resource_size(res),
-				"atmel tsadcc regs")) {
-		dev_err(&pdev->dev, "resources is unavailable.\n");
-		err = -EBUSY;
-		goto err_free_dev;
-	}
-
-	tsc_base = ioremap(res->start, resource_size(res));
-	if (!tsc_base) {
-		dev_err(&pdev->dev, "failed to map registers.\n");
-		err = -ENOMEM;
-		goto err_release_mem;
-	}
-
-	err = request_irq(ts_dev->irq, atmel_tsadcc_interrupt, 0,
-			pdev->dev.driver->name, ts_dev);
-	if (err) {
-		dev_err(&pdev->dev, "failed to allocate irq.\n");
-		goto err_unmap_regs;
-	}
-
-	ts_dev->clk = clk_get(&pdev->dev, "tsc_clk");
-	if (IS_ERR(ts_dev->clk)) {
-		dev_err(&pdev->dev, "failed to get ts_clk\n");
-		err = PTR_ERR(ts_dev->clk);
-		goto err_free_irq;
-	}
-
-	ts_dev->input = input_dev;
-	ts_dev->bufferedmeasure = 0;
-
-	snprintf(ts_dev->phys, sizeof(ts_dev->phys),
-		 "%s/input0", dev_name(&pdev->dev));
-
-	input_dev->name = "atmel touch screen controller";
-	input_dev->phys = ts_dev->phys;
-	input_dev->dev.parent = &pdev->dev;
-
-	__set_bit(EV_ABS, input_dev->evbit);
-	input_set_abs_params(input_dev, ABS_X, 0, 0x3FF, 0, 0);
-	input_set_abs_params(input_dev, ABS_Y, 0, 0x3FF, 0, 0);
-
-	input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
-
-	/* clk_enable() always returns 0, no need to check it */
-	clk_enable(ts_dev->clk);
-
-	prsc = clk_get_rate(ts_dev->clk);
-	dev_info(&pdev->dev, "Master clock is set at: %d Hz\n", prsc);
-
-	if (!pdata->adc_clock)
-		pdata->adc_clock = ADC_DEFAULT_CLOCK;
-
-	prsc = (prsc / (2 * pdata->adc_clock)) - 1;
-
-	/* saturate if this value is too high */
-	if (cpu_is_at91sam9rl()) {
-		if (prsc > PRESCALER_VAL(ATMEL_TSADCC_PRESCAL))
-			prsc = PRESCALER_VAL(ATMEL_TSADCC_PRESCAL);
-	} else {
-		if (prsc > PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL))
-			prsc = PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL);
-	}
-
-	dev_info(&pdev->dev, "Prescaler is set at: %d\n", prsc);
-
-	reg = ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE		|
-		((0x00 << 5) & ATMEL_TSADCC_SLEEP)	|	/* Normal Mode */
-		((0x01 << 6) & ATMEL_TSADCC_PENDET)	|	/* Enable Pen Detect */
-		(prsc << 8)				|
-		((0x26 << 16) & ATMEL_TSADCC_STARTUP)	|
-		((pdata->pendet_debounce << 28) & ATMEL_TSADCC_PENDBC);
-
-	atmel_tsadcc_write(ATMEL_TSADCC_CR, ATMEL_TSADCC_SWRST);
-	atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
-	atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
-	atmel_tsadcc_write(ATMEL_TSADCC_TSR,
-		(pdata->ts_sample_hold_time << 24) & ATMEL_TSADCC_TSSHTIM);
-
-	atmel_tsadcc_read(ATMEL_TSADCC_SR);
-	atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
-
-	/* All went ok, so register to the input system */
-	err = input_register_device(input_dev);
-	if (err)
-		goto err_fail;
-
-	return 0;
-
-err_fail:
-	clk_disable(ts_dev->clk);
-	clk_put(ts_dev->clk);
-err_free_irq:
-	free_irq(ts_dev->irq, ts_dev);
-err_unmap_regs:
-	iounmap(tsc_base);
-err_release_mem:
-	release_mem_region(res->start, resource_size(res));
-err_free_dev:
-	input_free_device(input_dev);
-err_free_mem:
-	kfree(ts_dev);
-	return err;
-}
-
-static int atmel_tsadcc_remove(struct platform_device *pdev)
-{
-	struct atmel_tsadcc *ts_dev = platform_get_drvdata(pdev);
-	struct resource *res;
-
-	free_irq(ts_dev->irq, ts_dev);
-
-	input_unregister_device(ts_dev->input);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	iounmap(tsc_base);
-	release_mem_region(res->start, resource_size(res));
-
-	clk_disable(ts_dev->clk);
-	clk_put(ts_dev->clk);
-
-	kfree(ts_dev);
-
-	return 0;
-}
-
-static struct platform_driver atmel_tsadcc_driver = {
-	.probe		= atmel_tsadcc_probe,
-	.remove		= atmel_tsadcc_remove,
-	.driver		= {
-		.name	= "atmel_tsadcc",
-	},
-};
-module_platform_driver(atmel_tsadcc_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Atmel TouchScreen Driver");
-MODULE_AUTHOR("Dan Liang <dan.liang@atmel.com>");
-