V4L/DVB (3218): Whitespace cleanups

- minor whitespace cleanups

Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>

28 files changed, 114 insertions, 114 deletions

diff --git a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
index fa7058108bf..0b940e152b7 100644
--- a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
+++ b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
@@ -298,7 +298,7 @@ static int flexcop_fe_request_firmware(struct dvb_frontend* fe, const struct fir
 }
 
 static int lgdt3303_pll_set(struct dvb_frontend* fe,
-		            struct dvb_frontend_parameters* params)
+			    struct dvb_frontend_parameters* params)
 {
 	struct flexcop_device *fc = fe->dvb->priv;
 	u8 buf[4];
diff --git a/drivers/media/dvb/bt8xx/dst_ca.c b/drivers/media/dvb/bt8xx/dst_ca.c
index 2239651969c..c650b4bf7f5 100644
--- a/drivers/media/dvb/bt8xx/dst_ca.c
+++ b/drivers/media/dvb/bt8xx/dst_ca.c
@@ -283,16 +283,17 @@ static int handle_dst_tag(struct dst_state *state, struct ca_msg *p_ca_message,
 		hw_buffer->msg[4] = 0x03;
 		hw_buffer->msg[5] = length & 0xff;
 		hw_buffer->msg[6] = 0x00;
+
 		/*
 		 *	Need to compute length for EN50221 section 8.3.2, for the time being
 		 *	assuming 8.3.2 is not applicable
 		 */
 		memcpy(&hw_buffer->msg[7], &p_ca_message->msg[4], length);
 	}
+
 	return 0;
 }
 
-
 static int write_to_8820(struct dst_state *state, struct ca_msg *hw_buffer, u8 length, u8 reply)
 {
 	if ((dst_put_ci(state, hw_buffer->msg, length, hw_buffer->msg, reply)) < 0) {
diff --git a/drivers/media/dvb/cinergyT2/Kconfig b/drivers/media/dvb/cinergyT2/Kconfig
index 7cf4c4a888e..6018fcdba1e 100644
--- a/drivers/media/dvb/cinergyT2/Kconfig
+++ b/drivers/media/dvb/cinergyT2/Kconfig
@@ -21,35 +21,35 @@ config DVB_CINERGYT2_TUNING
 config DVB_CINERGYT2_STREAM_URB_COUNT
 	int "Number of queued USB Request Blocks for Highspeed Stream Transfers"
 	depends on DVB_CINERGYT2_TUNING
-        default "32"
+	default "32"
 	help
 	  USB Request Blocks for Highspeed Stream transfers are scheduled in
 	  a queue for the Host Controller.
 
 	  Usually the default value is a safe choice.
 
-	  You may increase this number if you are using this device in a 
-	  Server Environment with many high-traffic USB Highspeed devices 
+	  You may increase this number if you are using this device in a
+	  Server Environment with many high-traffic USB Highspeed devices
 	  sharing the same USB bus.
 
 
 config DVB_CINERGYT2_STREAM_BUF_SIZE
 	int "Size of URB Stream Buffers for Highspeed Transfers"
 	depends on DVB_CINERGYT2_TUNING
-        default "512"
+	default "512"
 	help
 	  Should be a multiple of native buffer size of 512 bytes.
 	  Default value is a safe choice.
 
-	  You may increase this number if you are using this device in a 
-	  Server Environment with many high-traffic USB Highspeed devices 
+	  You may increase this number if you are using this device in a
+	  Server Environment with many high-traffic USB Highspeed devices
 	  sharing the same USB bus.
 
 
 config DVB_CINERGYT2_QUERY_INTERVAL
 	int "Status update interval [milliseconds]"
 	depends on DVB_CINERGYT2_TUNING
-        default "250"
+	default "250"
 	help
 	  This is the interval for status readouts from the demodulator.
 	  You may try lower values if you need more responsive signal quality
@@ -64,9 +64,9 @@ config DVB_CINERGYT2_QUERY_INTERVAL
 config DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE
 	bool "Register the onboard IR Remote Control Receiver as Input Device"
 	depends on DVB_CINERGYT2_TUNING
-        default "yes"
+	default "yes"
 	help
-	  Enable this option if you want to use the onboard Infrared Remote 
+	  Enable this option if you want to use the onboard Infrared Remote
 	  Control Receiver as Linux-Input device.
 
 	  Right now only the keycode table for the default Remote Control
@@ -77,7 +77,7 @@ config DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE
 config DVB_CINERGYT2_RC_QUERY_INTERVAL
 	int "Infrared Remote Controller update interval [milliseconds]"
 	depends on DVB_CINERGYT2_TUNING && DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE
-        default "50"
+	default "50"
 	help
 	  If you have a very fast-repeating remote control you can try lower
 	  values, for normal consumer receivers the default value should be
diff --git a/drivers/media/dvb/dvb-core/Kconfig b/drivers/media/dvb/dvb-core/Kconfig
index a9a7b342104..12ee912a570 100644
--- a/drivers/media/dvb/dvb-core/Kconfig
+++ b/drivers/media/dvb/dvb-core/Kconfig
@@ -5,7 +5,7 @@ config DVB_CORE
 	help
 	  DVB core utility functions for device handling, software fallbacks etc.
 	  Say Y when you have a DVB card and want to use it. Say Y if your want
-	  to build your drivers outside the kernel, but need the DVB core. All 
+	  to build your drivers outside the kernel, but need the DVB core. All
 	  in-kernel drivers will select this automatically if needed.
 	  If unsure say N.
 
diff --git a/drivers/media/dvb/dvb-core/Makefile b/drivers/media/dvb/dvb-core/Makefile
index c6baac20f52..7adb50c1e8e 100644
--- a/drivers/media/dvb/dvb-core/Makefile
+++ b/drivers/media/dvb/dvb-core/Makefile
@@ -3,7 +3,7 @@
 #
 
 dvb-core-objs = dvbdev.o dmxdev.o dvb_demux.o dvb_filter.o \
-	        dvb_ca_en50221.o dvb_frontend.o \
+		dvb_ca_en50221.o dvb_frontend.o \
 		dvb_net.o dvb_ringbuffer.o
 
 obj-$(CONFIG_DVB_CORE) += dvb-core.o
diff --git a/drivers/media/dvb/dvb-core/dvb_filter.c b/drivers/media/dvb/dvb-core/dvb_filter.c
index c49fd0bd718..772003fb182 100644
--- a/drivers/media/dvb/dvb-core/dvb_filter.c
+++ b/drivers/media/dvb/dvb-core/dvb_filter.c
@@ -409,16 +409,16 @@ static u8 *skip_pes_header(u8 **bufp)
 
 	if ((inbuf[6] & 0xc0) == 0x80){ /* mpeg2 */
 		if (buf[7] & PTS_ONLY)
-		        pts = buf+9;
+			pts = buf+9;
 		else pts = NULL;
 		buf = inbuf + 9 + inbuf[8];
 	} else {        /* mpeg1 */
 		for (buf = inbuf + 6; *buf == 0xff; buf++)
-		        if (buf == inbuf + 6 + 16) {
-		                break;
-		        }
+			if (buf == inbuf + 6 + 16) {
+				break;
+			}
 		if ((*buf & 0xc0) == 0x40)
-		        buf += 2;
+			buf += 2;
 		skip = mpeg1_skip_table [*buf >> 4];
 		if (skip == 5 || skip == 10) pts = buf;
 		else pts = NULL;
@@ -529,9 +529,9 @@ static void init_mpg_picture( struct mpg_picture *pic, int chan, int32_t field_t
 	pic->picture_header = 0;
 	pic->sequence_header_data
 		= ( INIT_HORIZONTAL_SIZE << 20 )
-		        | ( INIT_VERTICAL_SIZE << 8 )
-		        | ( INIT_ASPECT_RATIO << 4 )
-		        | ( INIT_FRAME_RATE );
+			| ( INIT_VERTICAL_SIZE << 8 )
+			| ( INIT_ASPECT_RATIO << 4 )
+			| ( INIT_FRAME_RATE );
 	pic->mpeg1_flag = 0;
 	pic->vinfo.horizontal_size
 		= INIT_DISP_HORIZONTAL_SIZE;
diff --git a/drivers/media/dvb/dvb-core/dvb_ringbuffer.c b/drivers/media/dvb/dvb-core/dvb_ringbuffer.c
index 283c6e9339a..77ad2410f4d 100644
--- a/drivers/media/dvb/dvb-core/dvb_ringbuffer.c
+++ b/drivers/media/dvb/dvb-core/dvb_ringbuffer.c
@@ -112,10 +112,10 @@ ssize_t dvb_ringbuffer_read(struct dvb_ringbuffer *rbuf, u8 *buf, size_t len, in
 	split = (rbuf->pread + len > rbuf->size) ? rbuf->size - rbuf->pread : 0;
 	if (split > 0) {
 		if (!usermem)
-		        memcpy(buf, rbuf->data+rbuf->pread, split);
+			memcpy(buf, rbuf->data+rbuf->pread, split);
 		else
-		        if (copy_to_user(buf, rbuf->data+rbuf->pread, split))
-		                return -EFAULT;
+			if (copy_to_user(buf, rbuf->data+rbuf->pread, split))
+				return -EFAULT;
 		buf += split;
 		todo -= split;
 		rbuf->pread = 0;
@@ -124,7 +124,7 @@ ssize_t dvb_ringbuffer_read(struct dvb_ringbuffer *rbuf, u8 *buf, size_t len, in
 		memcpy(buf, rbuf->data+rbuf->pread, todo);
 	else
 		if (copy_to_user(buf, rbuf->data+rbuf->pread, todo))
-		        return -EFAULT;
+			return -EFAULT;
 
 	rbuf->pread = (rbuf->pread + todo) % rbuf->size;
 
@@ -167,7 +167,7 @@ ssize_t dvb_ringbuffer_pkt_write(struct dvb_ringbuffer *rbuf, u8* buf, size_t le
 }
 
 ssize_t dvb_ringbuffer_pkt_read(struct dvb_ringbuffer *rbuf, size_t idx,
-		                int offset, u8* buf, size_t len, int usermem)
+				int offset, u8* buf, size_t len, int usermem)
 {
 	size_t todo;
 	size_t split;
@@ -183,10 +183,10 @@ ssize_t dvb_ringbuffer_pkt_read(struct dvb_ringbuffer *rbuf, size_t idx,
 	split = ((idx + len) > rbuf->size) ? rbuf->size - idx : 0;
 	if (split > 0) {
 		if (!usermem)
-		        memcpy(buf, rbuf->data+idx, split);
+			memcpy(buf, rbuf->data+idx, split);
 		else
-		        if (copy_to_user(buf, rbuf->data+idx, split))
-		                return -EFAULT;
+			if (copy_to_user(buf, rbuf->data+idx, split))
+				return -EFAULT;
 		buf += split;
 		todo -= split;
 		idx = 0;
@@ -195,7 +195,7 @@ ssize_t dvb_ringbuffer_pkt_read(struct dvb_ringbuffer *rbuf, size_t idx,
 		memcpy(buf, rbuf->data+idx, todo);
 	else
 		if (copy_to_user(buf, rbuf->data+idx, todo))
-		        return -EFAULT;
+			return -EFAULT;
 
 	return len;
 }
@@ -209,12 +209,12 @@ void dvb_ringbuffer_pkt_dispose(struct dvb_ringbuffer *rbuf, size_t idx)
 	// clean up disposed packets
 	while(dvb_ringbuffer_avail(rbuf) > DVB_RINGBUFFER_PKTHDRSIZE) {
 		if (DVB_RINGBUFFER_PEEK(rbuf, 2) == PKT_DISPOSED) {
-		        pktlen = DVB_RINGBUFFER_PEEK(rbuf, 0) << 8;
-		        pktlen |= DVB_RINGBUFFER_PEEK(rbuf, 1);
-		        DVB_RINGBUFFER_SKIP(rbuf, pktlen + DVB_RINGBUFFER_PKTHDRSIZE);
+			pktlen = DVB_RINGBUFFER_PEEK(rbuf, 0) << 8;
+			pktlen |= DVB_RINGBUFFER_PEEK(rbuf, 1);
+			DVB_RINGBUFFER_SKIP(rbuf, pktlen + DVB_RINGBUFFER_PKTHDRSIZE);
 		} else {
-		        // first packet is not disposed, so we stop cleaning now
-		        break;
+			// first packet is not disposed, so we stop cleaning now
+			break;
 		}
 	}
 }
@@ -242,8 +242,8 @@ ssize_t dvb_ringbuffer_pkt_next(struct dvb_ringbuffer *rbuf, size_t idx, size_t*
 		curpktstatus = rbuf->data[(idx + 2) % rbuf->size];
 
 		if (curpktstatus == PKT_READY) {
-		        *pktlen = curpktlen;
-		        return idx;
+			*pktlen = curpktlen;
+			return idx;
 		}
 
 		consumed += curpktlen + DVB_RINGBUFFER_PKTHDRSIZE;
diff --git a/drivers/media/dvb/dvb-core/dvb_ringbuffer.h b/drivers/media/dvb/dvb-core/dvb_ringbuffer.h
index fa476f662f8..6d256097277 100644
--- a/drivers/media/dvb/dvb-core/dvb_ringbuffer.h
+++ b/drivers/media/dvb/dvb-core/dvb_ringbuffer.h
@@ -106,7 +106,7 @@ extern void dvb_ringbuffer_flush_spinlock_wakeup(struct dvb_ringbuffer *rbuf);
 ** returns number of bytes transferred or -EFAULT
 */
 extern ssize_t dvb_ringbuffer_read(struct dvb_ringbuffer *rbuf, u8 *buf,
-		                   size_t len, int usermem);
+				   size_t len, int usermem);
 
 
 /* write routines & macros */
@@ -121,7 +121,7 @@ extern ssize_t dvb_ringbuffer_read(struct dvb_ringbuffer *rbuf, u8 *buf,
 ** returns number of bytes transferred or -EFAULT
 */
 extern ssize_t dvb_ringbuffer_write(struct dvb_ringbuffer *rbuf, const u8 *buf,
-		                    size_t len);
+				    size_t len);
 
 
 /**
@@ -133,7 +133,7 @@ extern ssize_t dvb_ringbuffer_write(struct dvb_ringbuffer *rbuf, const u8 *buf,
  * returns Number of bytes written, or -EFAULT, -ENOMEM, -EVINAL.
  */
 extern ssize_t dvb_ringbuffer_pkt_write(struct dvb_ringbuffer *rbuf, u8* buf,
-		                        size_t len);
+					size_t len);
 
 /**
  * Read from a packet in the ringbuffer. Note: unlike dvb_ringbuffer_read(), this
@@ -149,7 +149,7 @@ extern ssize_t dvb_ringbuffer_pkt_write(struct dvb_ringbuffer *rbuf, u8* buf,
  * returns Number of bytes read, or -EFAULT.
  */
 extern ssize_t dvb_ringbuffer_pkt_read(struct dvb_ringbuffer *rbuf, size_t idx,
-		                       int offset, u8* buf, size_t len, int usermem);
+				       int offset, u8* buf, size_t len, int usermem);
 
 /**
  * Dispose of a packet in the ring buffer.
diff --git a/drivers/media/dvb/dvb-core/dvbdev.c b/drivers/media/dvb/dvb-core/dvbdev.c
index a4aee866585..06b696e9acb 100644
--- a/drivers/media/dvb/dvb-core/dvbdev.c
+++ b/drivers/media/dvb/dvb-core/dvbdev.c
@@ -92,10 +92,10 @@ static int dvb_device_open(struct inode *inode, struct file *file)
 		old_fops = file->f_op;
 		file->f_op = fops_get(dvbdev->fops);
 		if(file->f_op->open)
-		        err = file->f_op->open(inode,file);
+			err = file->f_op->open(inode,file);
 		if (err) {
-		        fops_put(file->f_op);
-		        file->f_op = fops_get(old_fops);
+			fops_put(file->f_op);
+			file->f_op = fops_get(old_fops);
 		}
 		fops_put(old_fops);
 		return err;
@@ -356,18 +356,18 @@ int dvb_usercopy(struct inode *inode, struct file *file,
 	case _IOC_WRITE:
 	case (_IOC_WRITE | _IOC_READ):
 		if (_IOC_SIZE(cmd) <= sizeof(sbuf)) {
-		        parg = sbuf;
+			parg = sbuf;
 		} else {
-		        /* too big to allocate from stack */
-		        mbuf = kmalloc(_IOC_SIZE(cmd),GFP_KERNEL);
-		        if (NULL == mbuf)
-		                return -ENOMEM;
-		        parg = mbuf;
+			/* too big to allocate from stack */
+			mbuf = kmalloc(_IOC_SIZE(cmd),GFP_KERNEL);
+			if (NULL == mbuf)
+				return -ENOMEM;
+			parg = mbuf;
 		}
 
 		err = -EFAULT;
 		if (copy_from_user(parg, (void __user *)arg, _IOC_SIZE(cmd)))
-		        goto out;
+			goto out;
 		break;
 	}
 
@@ -384,7 +384,7 @@ int dvb_usercopy(struct inode *inode, struct file *file,
 	case _IOC_READ:
 	case (_IOC_WRITE | _IOC_READ):
 		if (copy_to_user((void __user *)arg, parg, _IOC_SIZE(cmd)))
-		        err = -EFAULT;
+			err = -EFAULT;
 		break;
 	}
 
diff --git a/drivers/media/dvb/dvb-core/dvbdev.h b/drivers/media/dvb/dvb-core/dvbdev.h
index 0cc6e4a0e27..74ed5853f0f 100644
--- a/drivers/media/dvb/dvb-core/dvbdev.h
+++ b/drivers/media/dvb/dvb-core/dvbdev.h
@@ -97,7 +97,7 @@ we simply define out own dvb_usercopy(), which will hopefully become
 generic_usercopy()  someday... */
 
 extern int dvb_usercopy(struct inode *inode, struct file *file,
-		            unsigned int cmd, unsigned long arg,
+			    unsigned int cmd, unsigned long arg,
 			    int (*func)(struct inode *inode, struct file *file,
 			    unsigned int cmd, void *arg));
 
diff --git a/drivers/media/dvb/dvb-usb/vp702x-fe.c b/drivers/media/dvb/dvb-usb/vp702x-fe.c
index 104b5d016c7..0885d9fb2bf 100644
--- a/drivers/media/dvb/dvb-usb/vp702x-fe.c
+++ b/drivers/media/dvb/dvb-usb/vp702x-fe.c
@@ -190,7 +190,7 @@ static int vp702x_fe_get_frontend(struct dvb_frontend* fe,
 }
 
 static int vp702x_fe_send_diseqc_msg (struct dvb_frontend* fe,
-			            struct dvb_diseqc_master_cmd *m)
+				    struct dvb_diseqc_master_cmd *m)
 {
 	struct vp702x_fe_state *st = fe->demodulator_priv;
 	u8 cmd[8],ibuf[10];
diff --git a/drivers/media/dvb/frontends/Kconfig b/drivers/media/dvb/frontends/Kconfig
index 17f90ef9ab6..3a3bcf6a2c9 100644
--- a/drivers/media/dvb/frontends/Kconfig
+++ b/drivers/media/dvb/frontends/Kconfig
@@ -56,18 +56,18 @@ comment "DVB-T (terrestrial) frontends"
 	depends on DVB_CORE
 
 config DVB_SP8870
- 	tristate "Spase sp8870 based"
+	tristate "Spase sp8870 based"
 	depends on DVB_CORE
 	select FW_LOADER
 	help
- 	  A DVB-T tuner module. Say Y when you want to support this frontend.
+	  A DVB-T tuner module. Say Y when you want to support this frontend.
 
 	  This driver needs external firmware. Please use the command
 	  "<kerneldir>/Documentation/dvb/get_dvb_firmware sp8870" to
 	  download/extract it, and then copy it to /usr/lib/hotplug/firmware.
 
 config DVB_SP887X
- 	tristate "Spase sp887x based"
+	tristate "Spase sp887x based"
 	depends on DVB_CORE
 	select FW_LOADER
 	help
@@ -84,10 +84,10 @@ config DVB_CX22700
 	  A DVB-T tuner module. Say Y when you want to support this frontend.
 
 config DVB_CX22702
- 	tristate "Conexant cx22702 demodulator (OFDM)"
- 	depends on DVB_CORE
- 	help
- 	  A DVB-T tuner module. Say Y when you want to support this frontend.
+	tristate "Conexant cx22702 demodulator (OFDM)"
+	depends on DVB_CORE
+	help
+	  A DVB-T tuner module. Say Y when you want to support this frontend.
 
 config DVB_L64781
 	tristate "LSI L64781"
@@ -104,7 +104,7 @@ config DVB_TDA1004X
 
 	  This driver needs external firmware. Please use the commands
 	  "<kerneldir>/Documentation/dvb/get_dvb_firmware tda10045",
-  	  "<kerneldir>/Documentation/dvb/get_dvb_firmware tda10046" to
+	  "<kerneldir>/Documentation/dvb/get_dvb_firmware tda10046" to
 	  download/extract them, and then copy them to /usr/lib/hotplug/firmware.
 
 config DVB_NXT6000
@@ -146,13 +146,13 @@ config DVB_VES1820
 	tristate "VLSI VES1820 based"
 	depends on DVB_CORE
 	help
- 	  A DVB-C tuner module. Say Y when you want to support this frontend.
+	  A DVB-C tuner module. Say Y when you want to support this frontend.
 
 config DVB_TDA10021
 	tristate "Philips TDA10021 based"
 	depends on DVB_CORE
 	help
- 	  A DVB-C tuner module. Say Y when you want to support this frontend.
+	  A DVB-C tuner module. Say Y when you want to support this frontend.
 
 config DVB_STV0297
 	tristate "ST STV0297 based"
diff --git a/drivers/media/dvb/frontends/cx24110.c b/drivers/media/dvb/frontends/cx24110.c
index ecd056e951f..d15d32c51dc 100644
--- a/drivers/media/dvb/frontends/cx24110.c
+++ b/drivers/media/dvb/frontends/cx24110.c
@@ -55,7 +55,7 @@ static int debug;
 
 static struct {u8 reg; u8 data;} cx24110_regdata[]=
 		      /* Comments beginning with @ denote this value should
-		         be the default */
+			 be the default */
 	{{0x09,0x01}, /* SoftResetAll */
 	 {0x09,0x00}, /* release reset */
 	 {0x01,0xe8}, /* MSB of code rate 27.5MS/s */
@@ -66,26 +66,26 @@ static struct {u8 reg; u8 data;} cx24110_regdata[]=
 	 {0x07,0x01}, /* @ Fclk, i.e. sampling clock, 60MHz */
 	 {0x0a,0x00}, /* @ partial chip disables, do not set */
 	 {0x0b,0x01}, /* set output clock in gapped mode, start signal low
-		         active for first byte */
+			 active for first byte */
 	 {0x0c,0x11}, /* no parity bytes, large hold time, serial data out */
 	 {0x0d,0x6f}, /* @ RS Sync/Unsync thresholds */
 	 {0x10,0x40}, /* chip doc is misleading here: write bit 6 as 1
-		         to avoid starting the BER counter. Reset the
-		         CRC test bit. Finite counting selected */
+			 to avoid starting the BER counter. Reset the
+			 CRC test bit. Finite counting selected */
 	 {0x15,0xff}, /* @ size of the limited time window for RS BER
-		         estimation. It is <value>*256 RS blocks, this
-		         gives approx. 2.6 sec at 27.5MS/s, rate 3/4 */
+			 estimation. It is <value>*256 RS blocks, this
+			 gives approx. 2.6 sec at 27.5MS/s, rate 3/4 */
 	 {0x16,0x00}, /* @ enable all RS output ports */
 	 {0x17,0x04}, /* @ time window allowed for the RS to sync */
 	 {0x18,0xae}, /* @ allow all standard DVB code rates to be scanned
-		         for automatically */
+			 for automatically */
 		      /* leave the current code rate and normalization
-		         registers as they are after reset... */
+			 registers as they are after reset... */
 	 {0x21,0x10}, /* @ during AutoAcq, search each viterbi setting
-		         only once */
+			 only once */
 	 {0x23,0x18}, /* @ size of the limited time window for Viterbi BER
-		         estimation. It is <value>*65536 channel bits, i.e.
-		         approx. 38ms at 27.5MS/s, rate 3/4 */
+			 estimation. It is <value>*65536 channel bits, i.e.
+			 approx. 38ms at 27.5MS/s, rate 3/4 */
 	 {0x24,0x24}, /* do not trigger Viterbi CRC test. Finite count window */
 		      /* leave front-end AGC parameters at default values */
 		      /* leave decimation AGC parameters at default values */
diff --git a/drivers/media/dvb/frontends/nxt6000.c b/drivers/media/dvb/frontends/nxt6000.c
index a458a3bfff7..a16eeba0020 100644
--- a/drivers/media/dvb/frontends/nxt6000.c
+++ b/drivers/media/dvb/frontends/nxt6000.c
@@ -574,11 +574,11 @@ static struct dvb_frontend_ops nxt6000_ops = {
 		.symbol_rate_max = 9360000,	/* FIXME */
 		.symbol_rate_tolerance = 4000,
 		.caps = FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
-		        FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 |
-		        FE_CAN_FEC_7_8 | FE_CAN_FEC_8_9 | FE_CAN_FEC_AUTO |
-		        FE_CAN_QAM_16 | FE_CAN_QAM_64 | FE_CAN_QAM_AUTO |
-		        FE_CAN_TRANSMISSION_MODE_AUTO | FE_CAN_GUARD_INTERVAL_AUTO |
-		        FE_CAN_HIERARCHY_AUTO,
+			FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 |
+			FE_CAN_FEC_7_8 | FE_CAN_FEC_8_9 | FE_CAN_FEC_AUTO |
+			FE_CAN_QAM_16 | FE_CAN_QAM_64 | FE_CAN_QAM_AUTO |
+			FE_CAN_TRANSMISSION_MODE_AUTO | FE_CAN_GUARD_INTERVAL_AUTO |
+			FE_CAN_HIERARCHY_AUTO,
 	},
 
 	.release = nxt6000_release,
diff --git a/drivers/media/dvb/frontends/s5h1420.c b/drivers/media/dvb/frontends/s5h1420.c
index 18715091aed..d6947759692 100644
--- a/drivers/media/dvb/frontends/s5h1420.c
+++ b/drivers/media/dvb/frontends/s5h1420.c
@@ -521,8 +521,8 @@ static void s5h1420_setfec_inversion(struct s5h1420_state* state,
 
 		case FEC_3_4:
 			s5h1420_writereg(state, 0x30, 0x04);
-		        s5h1420_writereg(state, 0x31, 0x12 | inversion);
-		        break;
+			s5h1420_writereg(state, 0x31, 0x12 | inversion);
+			break;
 
 		case FEC_5_6:
 			s5h1420_writereg(state, 0x30, 0x08);
diff --git a/drivers/media/dvb/frontends/sp887x.c b/drivers/media/dvb/frontends/sp887x.c
index e3b66578224..b3ae7dccc33 100644
--- a/drivers/media/dvb/frontends/sp887x.c
+++ b/drivers/media/dvb/frontends/sp887x.c
@@ -581,7 +581,7 @@ static struct dvb_frontend_ops sp887x_ops = {
 		.caps = FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
 			FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |
 			FE_CAN_QPSK | FE_CAN_QAM_16 | FE_CAN_QAM_64 |
-		        FE_CAN_RECOVER
+			FE_CAN_RECOVER
 	},
 
 	.release = sp887x_release,
diff --git a/drivers/media/dvb/frontends/tda10021.c b/drivers/media/dvb/frontends/tda10021.c
index 425cd19136f..21255cac979 100644
--- a/drivers/media/dvb/frontends/tda10021.c
+++ b/drivers/media/dvb/frontends/tda10021.c
@@ -95,7 +95,7 @@ static u8 tda10021_readreg (struct tda10021_state* state, u8 reg)
 	u8 b0 [] = { reg };
 	u8 b1 [] = { 0 };
 	struct i2c_msg msg [] = { { .addr = state->config->demod_address, .flags = 0, .buf = b0, .len = 1 },
-		                  { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } };
+				  { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } };
 	int ret;
 
 	ret = i2c_transfer (state->i2c, msg, 2);
@@ -434,7 +434,7 @@ static struct dvb_frontend_ops tda10021_ops = {
 		.frequency_max = 858000000,
 		.symbol_rate_min = (XIN/2)/64,     /* SACLK/64 == (XIN/2)/64 */
 		.symbol_rate_max = (XIN/2)/4,      /* SACLK/4 */
-	#if 0
+#if 0
 		.frequency_tolerance = ???,
 		.symbol_rate_tolerance = ???,  /* ppm */  /* == 8% (spec p. 5) */
 	#endif
diff --git a/drivers/media/dvb/frontends/tda1004x.c b/drivers/media/dvb/frontends/tda1004x.c
index c6ae5bfae5b..6c237fb2b82 100644
--- a/drivers/media/dvb/frontends/tda1004x.c
+++ b/drivers/media/dvb/frontends/tda1004x.c
@@ -289,10 +289,10 @@ static int tda10046h_set_bandwidth(struct tda1004x_state *state,
 	case BANDWIDTH_6_MHZ:
 		if (tda10046_clk53m)
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_6mhz_53M,
-					          sizeof(bandwidth_6mhz_53M));
+						  sizeof(bandwidth_6mhz_53M));
 		else
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_6mhz_48M,
-					          sizeof(bandwidth_6mhz_48M));
+						  sizeof(bandwidth_6mhz_48M));
 		if (state->config->if_freq == TDA10046_FREQ_045) {
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_MSB, 0x0a);
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_LSB, 0xab);
@@ -302,10 +302,10 @@ static int tda10046h_set_bandwidth(struct tda1004x_state *state,
 	case BANDWIDTH_7_MHZ:
 		if (tda10046_clk53m)
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_7mhz_53M,
-					          sizeof(bandwidth_7mhz_53M));
+						  sizeof(bandwidth_7mhz_53M));
 		else
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_7mhz_48M,
-					          sizeof(bandwidth_7mhz_48M));
+						  sizeof(bandwidth_7mhz_48M));
 		if (state->config->if_freq == TDA10046_FREQ_045) {
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_MSB, 0x0c);
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_LSB, 0x00);
@@ -315,10 +315,10 @@ static int tda10046h_set_bandwidth(struct tda1004x_state *state,
 	case BANDWIDTH_8_MHZ:
 		if (tda10046_clk53m)
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_8mhz_53M,
-					          sizeof(bandwidth_8mhz_53M));
+						  sizeof(bandwidth_8mhz_53M));
 		else
 			tda1004x_write_buf(state, TDA10046H_TIME_WREF1, bandwidth_8mhz_48M,
-					          sizeof(bandwidth_8mhz_48M));
+						  sizeof(bandwidth_8mhz_48M));
 		if (state->config->if_freq == TDA10046_FREQ_045) {
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_MSB, 0x0d);
 			tda1004x_write_byteI(state, TDA10046H_FREQ_PHY2_LSB, 0x55);
diff --git a/drivers/media/dvb/pluto2/Kconfig b/drivers/media/dvb/pluto2/Kconfig
index f02842be0d6..84f8f9f5286 100644
--- a/drivers/media/dvb/pluto2/Kconfig
+++ b/drivers/media/dvb/pluto2/Kconfig
@@ -8,7 +8,7 @@ config DVB_PLUTO2
 	  Support for PCI cards based on the Pluto2 FPGA like the Satelco
 	  Easywatch Mobile Terrestrial DVB-T Receiver.
 
-          Since these cards have no MPEG decoder onboard, they transmit
+	  Since these cards have no MPEG decoder onboard, they transmit
 	  only compressed MPEG data over the PCI bus, so you need
 	  an external software decoder to watch TV on your computer.
 
diff --git a/drivers/media/dvb/ttpci/Kconfig b/drivers/media/dvb/ttpci/Kconfig
index fa5034a9ecf..fa7e3894471 100644
--- a/drivers/media/dvb/ttpci/Kconfig
+++ b/drivers/media/dvb/ttpci/Kconfig
@@ -18,9 +18,9 @@ config DVB_AV7110
 	  This driver only supports the fullfeatured cards with
 	  onboard MPEG2 decoder.
 
-          This driver needs an external firmware. Please use the script
-          "<kerneldir>/Documentation/dvb/get_dvb_firmware av7110" to
-          download/extract it, and then copy it to /usr/lib/hotplug/firmware.
+	  This driver needs an external firmware. Please use the script
+	  "<kerneldir>/Documentation/dvb/get_dvb_firmware av7110" to
+	  download/extract it, and then copy it to /usr/lib/hotplug/firmware.
 
 	  Say Y if you own such a card and want to use it.
 
diff --git a/drivers/media/dvb/ttpci/Makefile b/drivers/media/dvb/ttpci/Makefile
index 825ab1c38a4..a690730ac39 100644
--- a/drivers/media/dvb/ttpci/Makefile
+++ b/drivers/media/dvb/ttpci/Makefile
@@ -16,7 +16,7 @@ EXTRA_CFLAGS = -Idrivers/media/dvb/dvb-core/ -Idrivers/media/dvb/frontends/
 hostprogs-y	:= fdump
 
 ifdef CONFIG_DVB_AV7110_FIRMWARE
-$(obj)/av7110.o: $(obj)/fdump $(obj)/av7110_firm.h 
+$(obj)/av7110.o: $(obj)/fdump $(obj)/av7110_firm.h
 
 $(obj)/av7110_firm.h:
 	$(obj)/fdump $(CONFIG_DVB_AV7110_FIRMWARE_FILE) dvb_ttpci_fw $@
diff --git a/drivers/media/dvb/ttpci/av7110.c b/drivers/media/dvb/ttpci/av7110.c
index 8fa487fb507..0bef1edf001 100644
--- a/drivers/media/dvb/ttpci/av7110.c
+++ b/drivers/media/dvb/ttpci/av7110.c
@@ -2259,7 +2259,7 @@ static int frontend_init(struct av7110 *av7110)
 			}
 
 			// Try the grundig 29504-451
-		        av7110->fe = tda8083_attach(&grundig_29504_451_config, &av7110->i2c_adap);
+			av7110->fe = tda8083_attach(&grundig_29504_451_config, &av7110->i2c_adap);
 			if (av7110->fe) {
 				av7110->fe->ops->diseqc_send_master_cmd = av7110_diseqc_send_master_cmd;
 				av7110->fe->ops->diseqc_send_burst = av7110_diseqc_send_burst;
@@ -2285,12 +2285,12 @@ static int frontend_init(struct av7110 *av7110)
 		case 0x0001: // Hauppauge/TT Nexus-T premium rev1.X
 
 			// ALPS TDLB7
-		        av7110->fe = sp8870_attach(&alps_tdlb7_config, &av7110->i2c_adap);
+			av7110->fe = sp8870_attach(&alps_tdlb7_config, &av7110->i2c_adap);
 			break;
 
 		case 0x0002: // Hauppauge/TT DVB-C premium rev2.X
 
-		        av7110->fe = ves1820_attach(&alps_tdbe2_config, &av7110->i2c_adap, read_pwm(av7110));
+			av7110->fe = ves1820_attach(&alps_tdbe2_config, &av7110->i2c_adap, read_pwm(av7110));
 			break;
 
 		case 0x0006: /* Fujitsu-Siemens DVB-S rev 1.6 */
diff --git a/drivers/media/dvb/ttpci/av7110_hw.c b/drivers/media/dvb/ttpci/av7110_hw.c
index 87106e8bf35..54279aaa482 100644
--- a/drivers/media/dvb/ttpci/av7110_hw.c
+++ b/drivers/media/dvb/ttpci/av7110_hw.c
@@ -1206,9 +1206,9 @@ int av7110_osd_capability(struct av7110 *av7110, osd_cap_t *cap)
 	switch (cap->cmd) {
 	case OSD_CAP_MEMSIZE:
 		if (FW_4M_SDRAM(av7110->arm_app))
-		        cap->val = 1000000;
+			cap->val = 1000000;
 		else
-		        cap->val = 92000;
+			cap->val = 92000;
 		return 0;
 	default:
 		return -EINVAL;
diff --git a/drivers/media/dvb/ttpci/budget-av.c b/drivers/media/dvb/ttpci/budget-av.c
index 9a33f6d5d92..f9d00452e63 100644
--- a/drivers/media/dvb/ttpci/budget-av.c
+++ b/drivers/media/dvb/ttpci/budget-av.c
@@ -275,7 +275,7 @@ static int ciintf_poll_slot_status(struct dvb_ca_en50221 *ca, int slot, int open
 		// that is unreliable however, so try and read from IO memory
 		if (!cam_present)
 		{
-   			saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO);
+			saa7146_setgpio(budget_av->budget.dev, 1, SAA7146_GPIO_OUTLO);
 			if (ttpci_budget_debiread(&budget_av->budget, DEBICICAM, 0, 1, 0, 1) != -ETIMEDOUT)
 			{
 				cam_present = 1;
diff --git a/drivers/media/dvb/ttpci/ttpci-eeprom.c b/drivers/media/dvb/ttpci/ttpci-eeprom.c
index 18aa22b5478..1f31e91195b 100644
--- a/drivers/media/dvb/ttpci/ttpci-eeprom.c
+++ b/drivers/media/dvb/ttpci/ttpci-eeprom.c
@@ -13,7 +13,7 @@
     Holger Waechtler	Convergence
 
     Copyright (C) 2002-2003 Ralph Metzler <rjkm@metzlerbros.de>
-		            Metzler Brothers Systementwicklung GbR
+			    Metzler Brothers Systementwicklung GbR
 
     This program is free software; you can redistribute it and/or modify
     it under the terms of the GNU General Public License as published by
diff --git a/drivers/media/dvb/ttusb-budget/Kconfig b/drivers/media/dvb/ttusb-budget/Kconfig
index c6c1d41a2ef..914587d52b5 100644
--- a/drivers/media/dvb/ttusb-budget/Kconfig
+++ b/drivers/media/dvb/ttusb-budget/Kconfig
@@ -10,7 +10,7 @@ config DVB_TTUSB_BUDGET
 	  Support for external USB adapters designed by Technotrend and
 	  produced by Hauppauge, shipped under the brand name 'Nova-USB'.
 
-          These devices don't have a MPEG decoder built in, so you need
+	  These devices don't have a MPEG decoder built in, so you need
 	  an external software decoder to watch TV.
 
 	  Say Y if you own such a device and want to use it.
diff --git a/drivers/media/dvb/ttusb-dec/Kconfig b/drivers/media/dvb/ttusb-dec/Kconfig
index c334526af66..e97244bd232 100644
--- a/drivers/media/dvb/ttusb-dec/Kconfig
+++ b/drivers/media/dvb/ttusb-dec/Kconfig
@@ -8,14 +8,14 @@ config DVB_TTUSB_DEC
 	  produced by Hauppauge, shipped under the brand name 'DEC2000-t'
 	  and 'DEC3000-s'.
 
-          Even if these devices have a MPEG decoder built in, they transmit
+	  Even if these devices have a MPEG decoder built in, they transmit
 	  only compressed MPEG data over the USB bus, so you need
 	  an external software decoder to watch TV on your computer.
 
-          This driver needs external firmware. Please use the commands
-          "<kerneldir>/Documentation/dvb/get_dvb_firmware dec2000t",
-          "<kerneldir>/Documentation/dvb/get_dvb_firmware dec2540t",
-          "<kerneldir>/Documentation/dvb/get_dvb_firmware dec3000s",
-          download/extract them, and then copy them to /usr/lib/hotplug/firmware.
+	  This driver needs external firmware. Please use the commands
+	  "<kerneldir>/Documentation/dvb/get_dvb_firmware dec2000t",
+	  "<kerneldir>/Documentation/dvb/get_dvb_firmware dec2540t",
+	  "<kerneldir>/Documentation/dvb/get_dvb_firmware dec3000s",
+	  download/extract them, and then copy them to /usr/lib/hotplug/firmware.
 
 	  Say Y if you own such a device and want to use it.
diff --git a/drivers/media/dvb/ttusb-dec/ttusb_dec.c b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
index 36bc9838cf1..d8966d1d25e 100644
--- a/drivers/media/dvb/ttusb-dec/ttusb_dec.c
+++ b/drivers/media/dvb/ttusb-dec/ttusb_dec.c
@@ -1182,7 +1182,7 @@ static void ttusb_dec_init_tasklet(struct ttusb_dec *dec)
 		     (unsigned long)dec);
 }
 
-static int ttusb_init_rc(struct ttusb_dec *dec)
+static int ttusb_init_rc( struct ttusb_dec *dec)
 {
 	struct input_dev *input_dev;
 	u8 b[] = { 0x00, 0x01 };
@@ -1203,13 +1203,12 @@ static int ttusb_init_rc(struct ttusb_dec *dec)
 	input_dev->keycode = rc_keys;
 
 	for (i = 0; i < ARRAY_SIZE(rc_keys); i++)
-		set_bit(rc_keys[i], input_dev->keybit);
+		  set_bit(rc_keys[i], input_dev->keybit);
 
 	input_register_device(input_dev);
 
 	if (usb_submit_urb(dec->irq_urb, GFP_KERNEL))
 		printk("%s: usb_submit_urb failed\n",__FUNCTION__);
-
 	/* enable irq pipe */
 	ttusb_dec_send_command(dec,0xb0,sizeof(b),b,NULL,NULL);