[media] tvp514x: s_routing should just change routing, not try to detect a signal

The s_routing function should not try to detect a signal. It is a really
bad idea to try to detect a valid video signal and return an error if
you can't. Changing input should do just that and nothing more.
Also don't power on the ADCs on s_routing, instead do that on querystd.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

1 files changed, 6 insertions, 71 deletions

diff --git a/drivers/media/i2c/tvp514x.c b/drivers/media/i2c/tvp514x.c
index 1f3943bb87d..d5e10215a28 100644
--- a/drivers/media/i2c/tvp514x.c
+++ b/drivers/media/i2c/tvp514x.c
@@ -519,6 +519,12 @@ static int tvp514x_querystd(struct v4l2_subdev *sd, v4l2_std_id *std_id)
 
 	*std_id = V4L2_STD_UNKNOWN;
 
+	/* To query the standard the TVP514x must power on the ADCs. */
+	if (!decoder->streaming) {
+		tvp514x_s_stream(sd, 1);
+		msleep(LOCK_RETRY_DELAY);
+	}
+
 	/* query the current standard */
 	current_std = tvp514x_query_current_std(sd);
 	if (current_std == STD_INVALID)
@@ -625,25 +631,12 @@ static int tvp514x_s_routing(struct v4l2_subdev *sd,
 	int err;
 	enum tvp514x_input input_sel;
 	enum tvp514x_output output_sel;
-	u8 sync_lock_status, lock_mask;
-	int try_count = LOCK_RETRY_COUNT;
 
 	if ((input >= INPUT_INVALID) ||
 			(output >= OUTPUT_INVALID))
 		/* Index out of bound */
 		return -EINVAL;
 
-	/*
-	 * For the sequence streamon -> streamoff and again s_input
-	 * it fails to lock the signal, since streamoff puts TVP514x
-	 * into power off state which leads to failure in sub-sequent s_input.
-	 *
-	 * So power up the TVP514x device here, since it is important to lock
-	 * the signal at this stage.
-	 */
-	if (!decoder->streaming)
-		tvp514x_s_stream(sd, 1);
-
 	input_sel = input;
 	output_sel = output;
 
@@ -660,64 +653,6 @@ static int tvp514x_s_routing(struct v4l2_subdev *sd,
 
 	decoder->tvp514x_regs[REG_INPUT_SEL].val = input_sel;
 	decoder->tvp514x_regs[REG_OUTPUT_FORMATTER1].val = output_sel;
-
-	/* Clear status */
-	msleep(LOCK_RETRY_DELAY);
-	err =
-	    tvp514x_write_reg(sd, REG_CLEAR_LOST_LOCK, 0x01);
-	if (err)
-		return err;
-
-	switch (input_sel) {
-	case INPUT_CVBS_VI1A:
-	case INPUT_CVBS_VI1B:
-	case INPUT_CVBS_VI1C:
-	case INPUT_CVBS_VI2A:
-	case INPUT_CVBS_VI2B:
-	case INPUT_CVBS_VI2C:
-	case INPUT_CVBS_VI3A:
-	case INPUT_CVBS_VI3B:
-	case INPUT_CVBS_VI3C:
-	case INPUT_CVBS_VI4A:
-		lock_mask = STATUS_CLR_SUBCAR_LOCK_BIT |
-			STATUS_HORZ_SYNC_LOCK_BIT |
-			STATUS_VIRT_SYNC_LOCK_BIT;
-		break;
-
-	case INPUT_SVIDEO_VI2A_VI1A:
-	case INPUT_SVIDEO_VI2B_VI1B:
-	case INPUT_SVIDEO_VI2C_VI1C:
-	case INPUT_SVIDEO_VI2A_VI3A:
-	case INPUT_SVIDEO_VI2B_VI3B:
-	case INPUT_SVIDEO_VI2C_VI3C:
-	case INPUT_SVIDEO_VI4A_VI1A:
-	case INPUT_SVIDEO_VI4A_VI1B:
-	case INPUT_SVIDEO_VI4A_VI1C:
-	case INPUT_SVIDEO_VI4A_VI3A:
-	case INPUT_SVIDEO_VI4A_VI3B:
-	case INPUT_SVIDEO_VI4A_VI3C:
-		lock_mask = STATUS_HORZ_SYNC_LOCK_BIT |
-			STATUS_VIRT_SYNC_LOCK_BIT;
-		break;
-	/* Need to add other interfaces*/
-	default:
-		return -EINVAL;
-	}
-
-	while (try_count-- > 0) {
-		/* Allow decoder to sync up with new input */
-		msleep(LOCK_RETRY_DELAY);
-
-		sync_lock_status = tvp514x_read_reg(sd,
-				REG_STATUS1);
-		if (lock_mask == (sync_lock_status & lock_mask))
-			/* Input detected */
-			break;
-	}
-
-	if (try_count < 0)
-		return -EINVAL;
-
 	decoder->input = input;
 	decoder->output = output;