Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

Conflicts:
	arch/sh/kernel/vmlinux.lds.S

7 files changed, 197 insertions, 37 deletions

diff --git a/drivers/media/video/cx23885/cimax2.c b/drivers/media/video/cx23885/cimax2.c
index 08582e58bdb..0316257b734 100644
--- a/drivers/media/video/cx23885/cimax2.c
+++ b/drivers/media/video/cx23885/cimax2.c
@@ -443,6 +443,7 @@ int netup_ci_init(struct cx23885_tsport *port)
 		goto err;
 
 	INIT_WORK(&state->work, netup_read_ci_status);
+	schedule_work(&state->work);
 
 	ci_dbg_print("%s: CI initialized!\n", __func__);
 
diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c
index 1a1048b18f7..6c3b51ce337 100644
--- a/drivers/media/video/cx23885/cx23885-417.c
+++ b/drivers/media/video/cx23885/cx23885-417.c
@@ -630,6 +630,39 @@ int mc417_memory_read(struct cx23885_dev *dev, u32 address, u32 *value)
 	return retval;
 }
 
+void mc417_gpio_set(struct cx23885_dev *dev, u32 mask)
+{
+	u32 val;
+
+	/* Set the gpio value */
+	mc417_register_read(dev, 0x900C, &val);
+	val |= (mask & 0x000ffff);
+	mc417_register_write(dev, 0x900C, val);
+}
+
+void mc417_gpio_clear(struct cx23885_dev *dev, u32 mask)
+{
+	u32 val;
+
+	/* Clear the gpio value */
+	mc417_register_read(dev, 0x900C, &val);
+	val &= ~(mask & 0x0000ffff);
+	mc417_register_write(dev, 0x900C, val);
+}
+
+void mc417_gpio_enable(struct cx23885_dev *dev, u32 mask, int asoutput)
+{
+	u32 val;
+
+	/* Enable GPIO direction bits */
+	mc417_register_read(dev, 0x9020, &val);
+	if (asoutput)
+		val |= (mask & 0x0000ffff);
+	else
+		val &= ~(mask & 0x0000ffff);
+
+	mc417_register_write(dev, 0x9020, val);
+}
 /* ------------------------------------------------------------------ */
 
 /* MPEG encoder API */
@@ -955,25 +988,8 @@ static int cx23885_load_firmware(struct cx23885_dev *dev)
 	retval |= mc417_register_write(dev, IVTV_REG_HW_BLOCKS,
 		IVTV_CMD_HW_BLOCKS_RST);
 
-	/* Restore GPIO settings, make sure EIO14 is enabled as an output. */
-	dprintk(2, "%s: GPIO output EIO 0-15 was = 0x%x\n",
-		__func__, gpio_output);
-	/* Power-up seems to have GPIOs AFU. This was causing digital side
-	 * to fail at power-up. Seems GPIOs should be set to 0x10ff0411 at
-	 * power-up.
-	 * gpio_output |= (1<<14);
-	 */
-	/* Note: GPIO14 is specific to the HVR1800 here */
-	gpio_output = 0x10ff0411 | (1<<14);
-	retval |= mc417_register_write(dev, 0x9020, gpio_output | (1<<14));
-	dprintk(2, "%s: GPIO output EIO 0-15 now = 0x%x\n",
-		__func__, gpio_output);
-
-	dprintk(1, "%s: GPIO value  EIO 0-15 was = 0x%x\n",
-		__func__, value);
-	value |= (1<<14);
-	dprintk(1, "%s: GPIO value  EIO 0-15 now = 0x%x\n",
-		__func__, value);
+	/* F/W power up disturbs the GPIOs, restore state */
+	retval |= mc417_register_write(dev, 0x9020, gpio_output);
 	retval |= mc417_register_write(dev, 0x900C, value);
 
 	retval |= mc417_register_read(dev, IVTV_REG_VPU, &value);
@@ -1788,9 +1804,6 @@ int cx23885_417_register(struct cx23885_dev *dev)
 		return err;
 	}
 
-	/* Initialize MC417 registers */
-	cx23885_mc417_init(dev);
-
 	printk(KERN_INFO "%s: registered device video%d [mpeg]\n",
 	       dev->name, dev->v4l_device->num);
 
diff --git a/drivers/media/video/cx23885/cx23885-cards.c b/drivers/media/video/cx23885/cx23885-cards.c
index ce29b5e34a1..3143d85ef31 100644
--- a/drivers/media/video/cx23885/cx23885-cards.c
+++ b/drivers/media/video/cx23885/cx23885-cards.c
@@ -201,6 +201,15 @@ struct cx23885_board cx23885_boards[] = {
 		.name		= "Mygica X8506 DMB-TH",
 		.portb		= CX23885_MPEG_DVB,
 	},
+	[CX23885_BOARD_MAGICPRO_PROHDTVE2] = {
+		.name		= "Magic-Pro ProHDTV Extreme 2",
+		.portb		= CX23885_MPEG_DVB,
+	},
+	[CX23885_BOARD_HAUPPAUGE_HVR1850] = {
+		.name		= "Hauppauge WinTV-HVR1850",
+		.portb		= CX23885_MPEG_ENCODER,
+		.portc		= CX23885_MPEG_DVB,
+	},
 };
 const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
 
@@ -324,6 +333,14 @@ struct cx23885_subid cx23885_subids[] = {
 		.subvendor = 0x14f1,
 		.subdevice = 0x8651,
 		.card      = CX23885_BOARD_MYGICA_X8506,
+	}, {
+		.subvendor = 0x14f1,
+		.subdevice = 0x8657,
+		.card      = CX23885_BOARD_MAGICPRO_PROHDTVE2,
+	}, {
+		.subvendor = 0x0070,
+		.subdevice = 0x8541,
+		.card      = CX23885_BOARD_HAUPPAUGE_HVR1850,
 	},
 };
 const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
@@ -483,8 +500,13 @@ static void hauppauge_eeprom(struct cx23885_dev *dev, u8 *eeprom_data)
 		/* WinTV-HVR1700 (PCIe, OEM, No IR, full height)
 		 * DVB-T and MPEG2 HW Encoder */
 		break;
+	case 85021:
+		/* WinTV-HVR1850 (PCIe, OEM, RCA in, IR, FM,
+			Dual channel ATSC and MPEG2 HW Encoder */
+		break;
 	default:
-		printk(KERN_WARNING "%s: warning: unknown hauppauge model #%d\n",
+		printk(KERN_WARNING "%s: warning: "
+			"unknown hauppauge model #%d\n",
 			dev->name, tv.model);
 		break;
 	}
@@ -574,13 +596,23 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
 		/* CX23417 GPIO's */
 		/* EIO15 Zilog Reset */
 		/* EIO14 S5H1409/CX24227 Reset */
+		mc417_gpio_enable(dev, GPIO_15 | GPIO_14, 1);
+
+		/* Put the demod into reset and protect the eeprom */
+		mc417_gpio_clear(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
+
+		/* Bring the demod and blaster out of reset */
+		mc417_gpio_set(dev, GPIO_15 | GPIO_14);
+		mdelay(100);
 
 		/* Force the TDA8295A into reset and back */
-		cx_set(GP0_IO, 0x00040004);
+		cx23885_gpio_enable(dev, GPIO_2, 1);
+		cx23885_gpio_set(dev, GPIO_2);
 		mdelay(20);
-		cx_clear(GP0_IO, 0x00000004);
+		cx23885_gpio_clear(dev, GPIO_2);
 		mdelay(20);
-		cx_set(GP0_IO, 0x00040004);
+		cx23885_gpio_set(dev, GPIO_2);
 		mdelay(20);
 		break;
 	case CX23885_BOARD_HAUPPAUGE_HVR1200:
@@ -715,14 +747,45 @@ void cx23885_gpio_setup(struct cx23885_dev *dev)
 		cx23885_gpio_set(dev, GPIO_9);
 		break;
 	case CX23885_BOARD_MYGICA_X8506:
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
 		/* GPIO-1 reset XC5000 */
-		/* GPIO-2 reset LGS8GL5 */
+		/* GPIO-2 reset LGS8GL5 / LGS8G75 */
 		cx_set(GP0_IO, 0x00060000);
 		cx_clear(GP0_IO, 0x00000006);
 		mdelay(100);
 		cx_set(GP0_IO, 0x00060006);
 		mdelay(100);
 		break;
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		/* GPIO-0 656_CLK */
+		/* GPIO-1 656_D0 */
+		/* GPIO-2 Wake# */
+		/* GPIO-3-10 cx23417 data0-7 */
+		/* GPIO-11-14 cx23417 addr0-3 */
+		/* GPIO-15-18 cx23417 READY, CS, RD, WR */
+		/* GPIO-19 IR_RX */
+		/* GPIO-20 C_IR_TX */
+		/* GPIO-21 I2S DAT */
+		/* GPIO-22 I2S WCLK */
+		/* GPIO-23 I2S BCLK */
+		/* ALT GPIO: EXP GPIO LATCH */
+
+		/* CX23417 GPIO's */
+		/* GPIO-14 S5H1411/CX24228 Reset */
+		/* GPIO-13 EEPROM write protect */
+		mc417_gpio_enable(dev, GPIO_14 | GPIO_13, 1);
+
+		/* Put the demod into reset and protect the eeprom */
+		mc417_gpio_clear(dev, GPIO_14 | GPIO_13);
+		mdelay(100);
+
+		/* Bring the demod out of reset */
+		mc417_gpio_set(dev, GPIO_14);
+		mdelay(100);
+
+		/* CX24228 GPIO */
+		/* Connected to IF / Mux */
+		break;
 	}
 }
 
@@ -739,6 +802,7 @@ int cx23885_ir_init(struct cx23885_dev *dev)
 	case CX23885_BOARD_HAUPPAUGE_HVR1275:
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
 		/* FIXME: Implement me */
 		break;
 	case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:
@@ -778,6 +842,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
 	case CX23885_BOARD_HAUPPAUGE_HVR1275:
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
 		if (dev->i2c_bus[0].i2c_rc == 0)
 			hauppauge_eeprom(dev, eeprom+0xc0);
 		break;
@@ -827,6 +892,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
 		ts2->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
 		break;
 	case CX23885_BOARD_MYGICA_X8506:
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
 		ts1->gen_ctrl_val  = 0x5; /* Parallel */
 		ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
 		ts1->src_sel_val   = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
@@ -844,6 +910,7 @@ void cx23885_card_setup(struct cx23885_dev *dev)
 	case CX23885_BOARD_HAUPPAUGE_HVR1275:
 	case CX23885_BOARD_HAUPPAUGE_HVR1255:
 	case CX23885_BOARD_HAUPPAUGE_HVR1210:
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
 	default:
 		ts2->gen_ctrl_val  = 0xc; /* Serial bus + punctured clock */
 		ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */
diff --git a/drivers/media/video/cx23885/cx23885-core.c b/drivers/media/video/cx23885/cx23885-core.c
index bf7bb1c412f..40d438d7234 100644
--- a/drivers/media/video/cx23885/cx23885-core.c
+++ b/drivers/media/video/cx23885/cx23885-core.c
@@ -713,12 +713,26 @@ static void cx23885_dev_checkrevision(struct cx23885_dev *dev)
 		dev->hwrevision = 0xa1;
 		break;
 	case 0x02:
-		/* CX23885-13Z */
+		/* CX23885-13Z/14Z */
 		dev->hwrevision = 0xb0;
 		break;
 	case 0x03:
-		/* CX23888-22Z */
-		dev->hwrevision = 0xc0;
+		if (dev->pci->device == 0x8880) {
+			/* CX23888-21Z/22Z */
+			dev->hwrevision = 0xc0;
+		} else {
+			/* CX23885-14Z */
+			dev->hwrevision = 0xa4;
+		}
+		break;
+	case 0x04:
+		if (dev->pci->device == 0x8880) {
+			/* CX23888-31Z */
+			dev->hwrevision = 0xd0;
+		} else {
+			/* CX23885-15Z, CX23888-31Z */
+			dev->hwrevision = 0xa5;
+		}
 		break;
 	case 0x0e:
 		/* CX23887-15Z */
@@ -756,6 +770,7 @@ static int cx23885_dev_setup(struct cx23885_dev *dev)
 
 	/* Configure the internal memory */
 	if (dev->pci->device == 0x8880) {
+		/* Could be 887 or 888, assume a default */
 		dev->bridge = CX23885_BRIDGE_887;
 		/* Apply a sensible clock frequency for the PCIe bridge */
 		dev->clk_freq = 25000000;
@@ -868,6 +883,14 @@ static int cx23885_dev_setup(struct cx23885_dev *dev)
 	dprintk(1, "%s() radio_type = 0x%x radio_addr = 0x%x\n",
 		__func__, dev->radio_type, dev->radio_addr);
 
+	/* The cx23417 encoder has GPIO's that need to be initialised
+	 * before DVB, so that demodulators and tuners are out of
+	 * reset before DVB uses them.
+	 */
+	if ((cx23885_boards[dev->board].portb == CX23885_MPEG_ENCODER) ||
+		(cx23885_boards[dev->board].portc == CX23885_MPEG_ENCODER))
+			cx23885_mc417_init(dev);
+
 	/* init hardware */
 	cx23885_reset(dev);
 
@@ -1250,6 +1273,7 @@ static int cx23885_start_dma(struct cx23885_tsport *port,
 	switch (dev->bridge) {
 	case CX23885_BRIDGE_885:
 	case CX23885_BRIDGE_887:
+	case CX23885_BRIDGE_888:
 		/* enable irqs */
 		dprintk(1, "%s() enabling TS int's and DMA\n", __func__);
 		cx_set(port->reg_ts_int_msk,  port->ts_int_msk_val);
diff --git a/drivers/media/video/cx23885/cx23885-dvb.c b/drivers/media/video/cx23885/cx23885-dvb.c
index 86ac529e62b..022fad798fc 100644
--- a/drivers/media/video/cx23885/cx23885-dvb.c
+++ b/drivers/media/video/cx23885/cx23885-dvb.c
@@ -396,7 +396,7 @@ static struct stv0900_reg stv0900_ts_regs[] = {
 
 static struct stv0900_config netup_stv0900_config = {
 	.demod_address = 0x68,
-	.xtal = 27000000,
+	.xtal = 8000000,
 	.clkmode = 3,/* 0-CLKI, 2-XTALI, else AUTO */
 	.diseqc_mode = 2,/* 2/3 PWM */
 	.ts_config_regs = stv0900_ts_regs,
@@ -408,14 +408,14 @@ static struct stv0900_config netup_stv0900_config = {
 
 static struct stv6110_config netup_stv6110_tunerconfig_a = {
 	.i2c_address = 0x60,
-	.mclk = 27000000,
-	.iq_wiring = 0,
+	.mclk = 16000000,
+	.clk_div = 1,
 };
 
 static struct stv6110_config netup_stv6110_tunerconfig_b = {
 	.i2c_address = 0x63,
-	.mclk = 27000000,
-	.iq_wiring = 1,
+	.mclk = 16000000,
+	.clk_div = 1,
 };
 
 static int tbs_set_voltage(struct dvb_frontend *fe, fe_sec_voltage_t voltage)
@@ -487,6 +487,26 @@ static int cx23885_dvb_set_frontend(struct dvb_frontend *fe,
 		port->set_frontend_save(fe, param) : -ENODEV;
 }
 
+static struct lgs8gxx_config magicpro_prohdtve2_lgs8g75_config = {
+	.prod = LGS8GXX_PROD_LGS8G75,
+	.demod_address = 0x19,
+	.serial_ts = 0,
+	.ts_clk_pol = 1,
+	.ts_clk_gated = 1,
+	.if_clk_freq = 30400, /* 30.4 MHz */
+	.if_freq = 6500, /* 6.50 MHz */
+	.if_neg_center = 1,
+	.ext_adc = 0,
+	.adc_signed = 1,
+	.adc_vpp = 2, /* 1.6 Vpp */
+	.if_neg_edge = 1,
+};
+
+static struct xc5000_config magicpro_prohdtve2_xc5000_config = {
+	.i2c_address = 0x61,
+	.if_khz = 6500,
+};
+
 static int dvb_register(struct cx23885_tsport *port)
 {
 	struct cx23885_dev *dev = port->dev;
@@ -833,6 +853,30 @@ static int dvb_register(struct cx23885_tsport *port)
 				&mygica_x8506_xc5000_config);
 		}
 		break;
+	case CX23885_BOARD_MAGICPRO_PROHDTVE2:
+		i2c_bus = &dev->i2c_bus[0];
+		i2c_bus2 = &dev->i2c_bus[1];
+		fe0->dvb.frontend = dvb_attach(lgs8gxx_attach,
+			&magicpro_prohdtve2_lgs8g75_config,
+			&i2c_bus->i2c_adap);
+		if (fe0->dvb.frontend != NULL) {
+			dvb_attach(xc5000_attach,
+				fe0->dvb.frontend,
+				&i2c_bus2->i2c_adap,
+				&magicpro_prohdtve2_xc5000_config);
+		}
+		break;
+	case CX23885_BOARD_HAUPPAUGE_HVR1850:
+		i2c_bus = &dev->i2c_bus[0];
+		fe0->dvb.frontend = dvb_attach(s5h1411_attach,
+			&hcw_s5h1411_config,
+			&i2c_bus->i2c_adap);
+		if (fe0->dvb.frontend != NULL)
+			dvb_attach(tda18271_attach, fe0->dvb.frontend,
+				0x60, &dev->i2c_bus[0].i2c_adap,
+				&hauppauge_tda18271_config);
+		break;
+
 	default:
 		printk(KERN_INFO "%s: The frontend of your DVB/ATSC card "
 			" isn't supported yet\n",
diff --git a/drivers/media/video/cx23885/cx23885-i2c.c b/drivers/media/video/cx23885/cx23885-i2c.c
index 384dec34134..4172cb38742 100644
--- a/drivers/media/video/cx23885/cx23885-i2c.c
+++ b/drivers/media/video/cx23885/cx23885-i2c.c
@@ -283,7 +283,6 @@ static struct i2c_algorithm cx23885_i2c_algo_template = {
 static struct i2c_adapter cx23885_i2c_adap_template = {
 	.name              = "cx23885",
 	.owner             = THIS_MODULE,
-	.id                = I2C_HW_B_CX23885,
 	.algo              = &cx23885_i2c_algo_template,
 };
 
diff --git a/drivers/media/video/cx23885/cx23885.h b/drivers/media/video/cx23885/cx23885.h
index 214a55e943b..86f26947bb7 100644
--- a/drivers/media/video/cx23885/cx23885.h
+++ b/drivers/media/video/cx23885/cx23885.h
@@ -76,6 +76,8 @@
 #define CX23885_BOARD_HAUPPAUGE_HVR1255        20
 #define CX23885_BOARD_HAUPPAUGE_HVR1210        21
 #define CX23885_BOARD_MYGICA_X8506             22
+#define CX23885_BOARD_MAGICPRO_PROHDTVE2       23
+#define CX23885_BOARD_HAUPPAUGE_HVR1850        24
 
 #define GPIO_0 0x00000001
 #define GPIO_1 0x00000002
@@ -87,6 +89,12 @@
 #define GPIO_7 0x00000080
 #define GPIO_8 0x00000100
 #define GPIO_9 0x00000200
+#define GPIO_10 0x00000400
+#define GPIO_11 0x00000800
+#define GPIO_12 0x00001000
+#define GPIO_13 0x00002000
+#define GPIO_14 0x00004000
+#define GPIO_15 0x00008000
 
 /* Currently unsupported by the driver: PAL/H, NTSC/Kr, SECAM B/G/H/LC */
 #define CX23885_NORMS (\
@@ -331,6 +339,7 @@ struct cx23885_dev {
 		CX23885_BRIDGE_UNDEFINED = 0,
 		CX23885_BRIDGE_885 = 885,
 		CX23885_BRIDGE_887 = 887,
+		CX23885_BRIDGE_888 = 888,
 	} bridge;
 
 	/* Analog video */
@@ -395,7 +404,7 @@ struct sram_channel {
 	u32  cmds_start;
 	u32  ctrl_start;
 	u32  cdt;
-	u32  fifo_start;;
+	u32  fifo_start;
 	u32  fifo_size;
 	u32  ptr1_reg;
 	u32  ptr2_reg;
@@ -504,6 +513,9 @@ extern void cx23885_417_check_encoder(struct cx23885_dev *dev);
 extern void cx23885_mc417_init(struct cx23885_dev *dev);
 extern int mc417_memory_read(struct cx23885_dev *dev, u32 address, u32 *value);
 extern int mc417_memory_write(struct cx23885_dev *dev, u32 address, u32 value);
+extern void mc417_gpio_set(struct cx23885_dev *dev, u32 mask);
+extern void mc417_gpio_clear(struct cx23885_dev *dev, u32 mask);
+extern void mc417_gpio_enable(struct cx23885_dev *dev, u32 mask, int asoutput);
 
 
 /* ----------------------------------------------------------- */