Merge branch 'v3.2-rc6' into next/drivers

9 files changed, 89 insertions, 44 deletions

diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index a1cb21f9530..1e0e27cbe98 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1606,6 +1606,14 @@ static const struct mmc_fixup blk_fixups[] =
 		  MMC_QUIRK_BLK_NO_CMD23),
 	MMC_FIXUP("MMC32G", 0x11, CID_OEMID_ANY, add_quirk_mmc,
 		  MMC_QUIRK_BLK_NO_CMD23),
+
+	/*
+	 * Some Micron MMC cards needs longer data read timeout than
+	 * indicated in CSD.
+	 */
+	MMC_FIXUP(CID_NAME_ANY, 0x13, 0x200, add_quirk_mmc,
+		  MMC_QUIRK_LONG_READ_TIME),
+
 	END_FIXUP
 };
 
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 5278ffb20e7..950b97d7412 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -529,6 +529,18 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card)
 			data->timeout_clks = 0;
 		}
 	}
+
+	/*
+	 * Some cards require longer data read timeout than indicated in CSD.
+	 * Address this by setting the read timeout to a "reasonably high"
+	 * value. For the cards tested, 300ms has proven enough. If necessary,
+	 * this value can be increased if other problematic cards require this.
+	 */
+	if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) {
+		data->timeout_ns = 300000000;
+		data->timeout_clks = 0;
+	}
+
 	/*
 	 * Some cards need very high timeouts if driven in SPI mode.
 	 * The worst observed timeout was 900ms after writing a
@@ -1213,6 +1225,46 @@ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
 	mmc_host_clk_release(host);
 }
 
+static void mmc_poweroff_notify(struct mmc_host *host)
+{
+	struct mmc_card *card;
+	unsigned int timeout;
+	unsigned int notify_type = EXT_CSD_NO_POWER_NOTIFICATION;
+	int err = 0;
+
+	card = host->card;
+
+	/*
+	 * Send power notify command only if card
+	 * is mmc and notify state is powered ON
+	 */
+	if (card && mmc_card_mmc(card) &&
+	    (card->poweroff_notify_state == MMC_POWERED_ON)) {
+
+		if (host->power_notify_type == MMC_HOST_PW_NOTIFY_SHORT) {
+			notify_type = EXT_CSD_POWER_OFF_SHORT;
+			timeout = card->ext_csd.generic_cmd6_time;
+			card->poweroff_notify_state = MMC_POWEROFF_SHORT;
+		} else {
+			notify_type = EXT_CSD_POWER_OFF_LONG;
+			timeout = card->ext_csd.power_off_longtime;
+			card->poweroff_notify_state = MMC_POWEROFF_LONG;
+		}
+
+		err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+				 EXT_CSD_POWER_OFF_NOTIFICATION,
+				 notify_type, timeout);
+
+		if (err && err != -EBADMSG)
+			pr_err("Device failed to respond within %d poweroff "
+			       "time. Forcefully powering down the device\n",
+			       timeout);
+
+		/* Set the card state to no notification after the poweroff */
+		card->poweroff_notify_state = MMC_NO_POWER_NOTIFICATION;
+	}
+}
+
 /*
  * Apply power to the MMC stack.  This is a two-stage process.
  * First, we enable power to the card without the clock running.
@@ -1269,42 +1321,12 @@ static void mmc_power_up(struct mmc_host *host)
 
 void mmc_power_off(struct mmc_host *host)
 {
-	struct mmc_card *card;
-	unsigned int notify_type;
-	unsigned int timeout;
-	int err;
-
 	mmc_host_clk_hold(host);
 
-	card = host->card;
 	host->ios.clock = 0;
 	host->ios.vdd = 0;
 
-	if (card && mmc_card_mmc(card) &&
-	    (card->poweroff_notify_state == MMC_POWERED_ON)) {
-
-		if (host->power_notify_type == MMC_HOST_PW_NOTIFY_SHORT) {
-			notify_type = EXT_CSD_POWER_OFF_SHORT;
-			timeout = card->ext_csd.generic_cmd6_time;
-			card->poweroff_notify_state = MMC_POWEROFF_SHORT;
-		} else {
-			notify_type = EXT_CSD_POWER_OFF_LONG;
-			timeout = card->ext_csd.power_off_longtime;
-			card->poweroff_notify_state = MMC_POWEROFF_LONG;
-		}
-
-		err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
-				 EXT_CSD_POWER_OFF_NOTIFICATION,
-				 notify_type, timeout);
-
-		if (err && err != -EBADMSG)
-			pr_err("Device failed to respond within %d poweroff "
-			       "time. Forcefully powering down the device\n",
-			       timeout);
-
-		/* Set the card state to no notification after the poweroff */
-		card->poweroff_notify_state = MMC_NO_POWER_NOTIFICATION;
-	}
+	mmc_poweroff_notify(host);
 
 	/*
 	 * Reset ocr mask to be the highest possible voltage supported for
@@ -2196,7 +2218,7 @@ int mmc_card_sleep(struct mmc_host *host)
 
 	mmc_bus_get(host);
 
-	if (host->bus_ops && !host->bus_dead && host->bus_ops->awake)
+	if (host->bus_ops && !host->bus_dead && host->bus_ops->sleep)
 		err = host->bus_ops->sleep(host);
 
 	mmc_bus_put(host);
@@ -2302,8 +2324,17 @@ int mmc_suspend_host(struct mmc_host *host)
 		 * pre-claim the host.
 		 */
 		if (mmc_try_claim_host(host)) {
-			if (host->bus_ops->suspend)
+			if (host->bus_ops->suspend) {
+				/*
+				 * For eMMC 4.5 device send notify command
+				 * before sleep, because in sleep state eMMC 4.5
+				 * devices respond to only RESET and AWAKE cmd
+				 */
+				mmc_poweroff_notify(host);
 				err = host->bus_ops->suspend(host);
+			}
+			mmc_do_release_host(host);
+
 			if (err == -ENOSYS || !host->bus_ops->resume) {
 				/*
 				 * We simply "remove" the card in this case.
@@ -2318,7 +2349,6 @@ int mmc_suspend_host(struct mmc_host *host)
 				host->pm_flags = 0;
 				err = 0;
 			}
-			mmc_do_release_host(host);
 		} else {
 			err = -EBUSY;
 		}
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index dbf421a6279..d240427c124 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -876,17 +876,21 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	 * set the notification byte in the ext_csd register of device
 	 */
 	if ((host->caps2 & MMC_CAP2_POWEROFF_NOTIFY) &&
-	    (card->poweroff_notify_state == MMC_NO_POWER_NOTIFICATION)) {
+	    (card->ext_csd.rev >= 6)) {
 		err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
 				 EXT_CSD_POWER_OFF_NOTIFICATION,
 				 EXT_CSD_POWER_ON,
 				 card->ext_csd.generic_cmd6_time);
 		if (err && err != -EBADMSG)
 			goto free_card;
-	}
 
-	if (!err)
-		card->poweroff_notify_state = MMC_POWERED_ON;
+		/*
+		 * The err can be -EBADMSG or 0,
+		 * so check for success and update the flag
+		 */
+		if (!err)
+			card->poweroff_notify_state = MMC_POWERED_ON;
+	}
 
 	/*
 	 * Activate high speed (if supported)
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
index 325ea61e12d..8e0fbe99404 100644
--- a/drivers/mmc/host/mxcmmc.c
+++ b/drivers/mmc/host/mxcmmc.c
@@ -732,6 +732,7 @@ static void mxcmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 				"failed to config DMA channel. Falling back to PIO\n");
 			dma_release_channel(host->dma);
 			host->do_dma = 0;
+			host->dma = NULL;
 		}
 	}
 
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index f0d792183b8..d1fb561e089 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -1010,6 +1010,7 @@ static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host *host, int errno)
 			host->data->sg_len,
 			omap_hsmmc_get_dma_dir(host, host->data));
 		omap_free_dma(dma_ch);
+		host->data->host_cookie = 0;
 	}
 	host->data = NULL;
 }
@@ -1575,8 +1576,10 @@ static void omap_hsmmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
 	struct mmc_data *data = mrq->data;
 
 	if (host->use_dma) {
-		dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
-			     omap_hsmmc_get_dma_dir(host, data));
+		if (data->host_cookie)
+			dma_unmap_sg(mmc_dev(host->mmc), data->sg,
+				     data->sg_len,
+				     omap_hsmmc_get_dma_dir(host, data));
 		data->host_cookie = 0;
 	}
 }
diff --git a/drivers/mmc/host/sdhci-cns3xxx.c b/drivers/mmc/host/sdhci-cns3xxx.c
index 4b920b7621c..87b6f079b6e 100644
--- a/drivers/mmc/host/sdhci-cns3xxx.c
+++ b/drivers/mmc/host/sdhci-cns3xxx.c
@@ -15,6 +15,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/mmc/host.h>
+#include <linux/module.h>
 #include <mach/cns3xxx.h>
 #include "sdhci-pltfm.h"
 
diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
index 3d00e722efc..cb60c4197e0 100644
--- a/drivers/mmc/host/sdhci-s3c.c
+++ b/drivers/mmc/host/sdhci-s3c.c
@@ -644,8 +644,6 @@ static int sdhci_s3c_resume(struct platform_device *dev)
 static struct platform_driver sdhci_s3c_driver = {
 	.probe		= sdhci_s3c_probe,
 	.remove		= __devexit_p(sdhci_s3c_remove),
-	.suspend	= sdhci_s3c_suspend,
-	.resume	        = sdhci_s3c_resume,
 	.driver		= {
 		.owner	= THIS_MODULE,
 		.name	= "s3c-sdhci",
diff --git a/drivers/mmc/host/sh_mmcif.c b/drivers/mmc/host/sh_mmcif.c
index 369366c8e20..d5505f3fe2a 100644
--- a/drivers/mmc/host/sh_mmcif.c
+++ b/drivers/mmc/host/sh_mmcif.c
@@ -908,7 +908,7 @@ static void sh_mmcif_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		if (host->power) {
 			pm_runtime_put(&host->pd->dev);
 			host->power = false;
-			if (p->down_pwr)
+			if (p->down_pwr && ios->power_mode == MMC_POWER_OFF)
 				p->down_pwr(host->pd);
 		}
 		host->state = STATE_IDLE;
diff --git a/drivers/mmc/host/tmio_mmc_pio.c b/drivers/mmc/host/tmio_mmc_pio.c
index d85a60cda16..4208b395806 100644
--- a/drivers/mmc/host/tmio_mmc_pio.c
+++ b/drivers/mmc/host/tmio_mmc_pio.c
@@ -798,7 +798,7 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		/* start bus clock */
 		tmio_mmc_clk_start(host);
 	} else if (ios->power_mode != MMC_POWER_UP) {
-		if (host->set_pwr)
+		if (host->set_pwr && ios->power_mode == MMC_POWER_OFF)
 			host->set_pwr(host->pdev, 0);
 		if ((pdata->flags & TMIO_MMC_HAS_COLD_CD) &&
 		    pdata->power) {