Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6: (226 commits)
  mtd: tests: annotate as DANGEROUS in Kconfig
  mtd: tests: don't use mtd0 as a default
  mtd: clean up usage of MTD_DOCPROBE_ADDRESS
  jffs2: add compr=lzo and compr=zlib options
  jffs2: implement mount option parsing and compression overriding
  mtd: nand: initialize ops.mode
  mtd: provide an alias for the redboot module name
  mtd: m25p80: don't probe device which has status of 'disabled'
  mtd: nand_h1900 never worked
  mtd: Add DiskOnChip G3 support
  mtd: m25p80: add EON flash EN25Q32B into spi flash id table
  mtd: mark block device queue as non-rotational
  mtd: r852: make r852_pm_ops static
  mtd: m25p80: add support for at25df321a spi data flash
  mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
  mtd: nand: switch `check_pattern()' to standard `memcmp()'
  mtd: nand: invalidate cache on unaligned reads
  mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
  mtd: nand: wait to set BBT version
  mtd: nand: scrub BBT on ECC errors
  ...

Fix up trivial conflicts:
 - arch/arm/mach-at91/board-usb-a9260.c
	Merged into board-usb-a926x.c
 - drivers/mtd/maps/lantiq-flash.c
	add_mtd_partitions -> mtd_device_register vs changed to use
	mtd_device_parse_register.

1 files changed, 0 insertions, 26 deletions

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index c0c328c5b13..8e0c4bf9f7f 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -41,8 +41,6 @@ config MTD_PHYSMAP_START
 	  are mapped on your particular target board. Refer to the
 	  memory map which should hopefully be in the documentation for
 	  your board.
-	  Ignore this option if you use run-time physmap configuration
-	  (i.e., run-time calling physmap_configure()).
 
 config MTD_PHYSMAP_LEN
 	hex "Physical length of flash mapping"
@@ -55,8 +53,6 @@ config MTD_PHYSMAP_LEN
 	  than the total amount of flash present. Refer to the memory
 	  map which should hopefully be in the documentation for your
 	  board.
-	  Ignore this option if you use run-time physmap configuration
-	  (i.e., run-time calling physmap_configure()).
 
 config MTD_PHYSMAP_BANKWIDTH
 	int "Bank width in octets"
@@ -67,8 +63,6 @@ config MTD_PHYSMAP_BANKWIDTH
 	  in octets. For example, if you have a data bus width of 32
 	  bits, you would set the bus width octet value to 4. This is
 	  used internally by the CFI drivers.
-	  Ignore this option if you use run-time physmap configuration
-	  (i.e., run-time calling physmap_configure()).
 
 config MTD_PHYSMAP_OF
 	tristate "Flash device in physical memory map based on OF description"
@@ -260,7 +254,6 @@ config MTD_BCM963XX
 config MTD_LANTIQ
 	tristate "Lantiq SoC NOR support"
 	depends on LANTIQ
-	select MTD_PARTITIONS
 	help
 	  Support for NOR flash attached to the Lantiq SoC's External Bus Unit.
 
@@ -339,10 +332,6 @@ config MTD_SOLUTIONENGINE
 	  This enables access to the flash chips on the Hitachi SolutionEngine and
 	  similar boards. Say 'Y' if you are building a kernel for such a board.
 
-config MTD_ARM_INTEGRATOR
-	tristate "CFI Flash device mapped on ARM Integrator/P720T"
-	depends on ARM && MTD_CFI
-
 config MTD_CDB89712
 	tristate "Cirrus CDB89712 evaluation board mappings"
 	depends on MTD_CFI && ARCH_CDB89712
@@ -398,13 +387,6 @@ config MTD_AUTCPU12
 	  This enables access to the NV-RAM on autronix autcpu12 board.
 	  If you have such a board, say 'Y'.
 
-config MTD_EDB7312
-	tristate "CFI Flash device mapped on EDB7312"
-	depends on ARCH_EDB7312 && MTD_CFI
-	help
-	  This enables access to the CFI Flash on the Cogent EDB7312 board.
-	  If you have such a board, say 'Y' here.
-
 config MTD_IMPA7
 	tristate "JEDEC Flash device mapped on impA7"
 	depends on ARM && MTD_JEDECPROBE
@@ -412,14 +394,6 @@ config MTD_IMPA7
 	  This enables access to the NOR Flash on the impA7 board of
 	  implementa GmbH. If you have such a board, say 'Y' here.
 
-config MTD_CEIVA
-	tristate "JEDEC Flash device mapped on Ceiva/Polaroid PhotoMax Digital Picture Frame"
-	depends on MTD_JEDECPROBE && ARCH_CEIVA
-	help
-	  This enables access to the flash chips on the Ceiva/Polaroid
-	  PhotoMax Digital Picture Frame.
-	  If you have such a device, say 'Y'.
-
 config MTD_H720X
 	tristate "Hynix evaluation board mappings"
 	depends on MTD_CFI && ( ARCH_H7201 || ARCH_H7202 )