Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd

Pull mtd update from David Woodhouse:
 - More robust parsing especially of xattr data in JFFS2
 - Updates to mxc_nand and gpmi drivers to support new boards and device tree
 - Improve consistency of information about ECC strength in NAND devices
 - Clean up partition handling of plat_nand
 - Support NAND drivers without dedicated access to OOB area
 - BCH hardware ECC support for OMAP
 - Other fixes and cleanups, and a few new device IDs

Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.

* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
  mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
  mtd: block2mtd: fix recursive call of mtd_writev
  mtd: gpmi-nand: define ecc.strength
  mtd: of_parts: fix breakage in Kconfig
  mtd: nand: fix scan_read_raw_oob
  mtd: docg3 fix in-middle of blocks reads
  mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
  mtd: add fixup for S29NS512P NOR flash.
  jffs2: allow to complete xattr integrity check on first GC scan
  jffs2: allow to discriminate between recoverable and non-recoverable errors
  mtd: nand: omap: add support for hardware BCH ecc
  ARM: OMAP3: gpmc: add BCH ecc api and modes
  mtd: nand: check the return code of 'read_oob/read_oob_raw'
  mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
  mtd: m25p80: Add support for Winbond W25Q80BW
  jffs2: get rid of jffs2_sync_super
  jffs2: remove unnecessary GC pass on sync
  jffs2: remove unnecessary GC pass on umount
  jffs2: remove lock_super
  mtd: gpmi: add gpmi support for mx6q
  ...

1 files changed, 41 insertions, 1 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 7d17cecad69..31bb7e5b504 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -115,6 +115,46 @@ config MTD_NAND_OMAP2
           Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4
 	  platforms.
 
+config MTD_NAND_OMAP_BCH
+	depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3
+	bool "Enable support for hardware BCH error correction"
+	default n
+	select BCH
+	select BCH_CONST_PARAMS
+	help
+	 Support for hardware BCH error correction.
+
+choice
+	prompt "BCH error correction capability"
+	depends on MTD_NAND_OMAP_BCH
+
+config MTD_NAND_OMAP_BCH8
+	bool "8 bits / 512 bytes (recommended)"
+	help
+	 Support correcting up to 8 bitflips per 512-byte block.
+	 This will use 13 bytes of spare area per 512 bytes of page data.
+	 This is the recommended mode, as 4-bit mode does not work
+	 on some OMAP3 revisions, due to a hardware bug.
+
+config MTD_NAND_OMAP_BCH4
+	bool "4 bits / 512 bytes"
+	help
+	 Support correcting up to 4 bitflips per 512-byte block.
+	 This will use 7 bytes of spare area per 512 bytes of page data.
+	 Note that this mode does not work on some OMAP3 revisions, due to a
+	 hardware bug. Please check your OMAP datasheet before selecting this
+	 mode.
+
+endchoice
+
+if MTD_NAND_OMAP_BCH
+config BCH_CONST_M
+	default 13
+config BCH_CONST_T
+	default 4 if MTD_NAND_OMAP_BCH4
+	default 8 if MTD_NAND_OMAP_BCH8
+endif
+
 config MTD_NAND_IDS
 	tristate
 
@@ -440,7 +480,7 @@ config MTD_NAND_NANDSIM
 
 config MTD_NAND_GPMI_NAND
         bool "GPMI NAND Flash Controller driver"
-        depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28)
+        depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q)
         help
 	 Enables NAND Flash support for IMX23 or IMX28.
 	 The GPMI controller is very powerful, with the help of BCH