Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

1 files changed, 0 insertions, 40 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 8ca417614c5..598cd0a3ade 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -406,46 +406,6 @@ config MTD_NAND_ATMEL
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
 	  on Atmel AT91 and AVR32 processors.
-choice
-	prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32"
-	depends on MTD_NAND_ATMEL
-
-config MTD_NAND_ATMEL_ECC_HW
-	bool "Hardware ECC"
-	depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32
-	help
-	  Use hardware ECC instead of software ECC when the chip
-	  supports it.
-
-	  The hardware ECC controller is capable of single bit error
-	  correction and 2-bit random detection per page.
-
-	  NB : hardware and software ECC schemes are incompatible.
-	  If you switch from one to another, you'll have to erase your
-	  mtd partition.
-
-	  If unsure, say Y
-
-config MTD_NAND_ATMEL_ECC_SOFT
-	bool "Software ECC"
-	help
-	  Use software ECC.
-
-	  NB : hardware and software ECC schemes are incompatible.
-	  If you switch from one to another, you'll have to erase your
-	  mtd partition.
-
-config MTD_NAND_ATMEL_ECC_NONE
-	bool "No ECC (testing only, DANGEROUS)"
-	depends on DEBUG_KERNEL
-	help
-	  No ECC will be used.
-	  It's not a good idea and it should be reserved for testing
-	  purpose only.
-
-	  If unsure, say N
-
-endchoice
 
 config MTD_NAND_PXA3xx
 	tristate "Support for NAND flash devices on PXA3xx"