bnx2x: Supporting BCM8727 PHY

Adding support for BCM8727 - a dual port SFP+ PHY. That includes verification of
the optic module vendor and part number - the list of approved modules resides
on the nvram and the module is verified by the FW. Since not all users would
like to use this verification feature, it can be disabled. The default behavior
is to issue a warning if the module is not approved, but still allow using it -
but it is also possible to disable the link if the module is not approved.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 53 insertions, 14 deletions

diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c
index b404a9b66d5..197dbe4dad2 100644
--- a/drivers/net/bnx2x_main.c
+++ b/drivers/net/bnx2x_main.c
@@ -2637,7 +2637,7 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn)
 {
 	int port = BP_PORT(bp);
 	int reg_offset;
-	u32 val;
+	u32 val, swap_val, swap_override;
 
 	reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 :
 			     MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
@@ -2661,6 +2661,17 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn)
 				       MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
 			break;
 
+		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+			/* The PHY reset is controlled by GPIO 1 */
+			/* fake the port number to cancel the swap done in
+			   set_gpio() */
+			swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+			swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
+			port = (swap_val && swap_override) ^ 1;
+			bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
+				       MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
+			break;
+
 		default:
 			break;
 		}
@@ -5562,6 +5573,8 @@ static void bnx2x_setup_fan_failure_detection(struct bnx2x *bp)
 				((phy_type ==
 				  PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) ||
 				 (phy_type ==
+				  PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) ||
+				 (phy_type ==
 				  PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481));
 		}
 
@@ -5812,6 +5825,7 @@ static int bnx2x_init_common(struct bnx2x *bp)
 	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
 	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
 	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
 		bp->port.need_hw_lock = 1;
 		break;
 
@@ -6050,10 +6064,15 @@ static int bnx2x_init_port(struct bnx2x *bp)
 		break;
 
 	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
 		/* add SPIO 5 to group 0 */
-		val = REG_RD(bp, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
+		{
+		u32 reg_addr = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 :
+				       MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
+		val = REG_RD(bp, reg_addr);
 		val |= AEU_INPUTS_ATTN_BITS_SPIO5;
-		REG_WR(bp, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, val);
+		REG_WR(bp, reg_addr, val);
+		}
 		break;
 
 	default:
@@ -6203,7 +6222,7 @@ init_hw_err:
 }
 
 /* send the MCP a request, block until there is a reply */
-static u32 bnx2x_fw_command(struct bnx2x *bp, u32 command)
+u32 bnx2x_fw_command(struct bnx2x *bp, u32 command)
 {
 	int func = BP_FUNC(bp);
 	u32 seq = ++bp->fw_seq;
@@ -7676,6 +7695,9 @@ static void __devinit bnx2x_get_common_hwinfo(struct bnx2x *bp)
 		BNX2X_ERR("This driver needs bc_ver %X but found %X,"
 			  " please upgrade BC\n", BNX2X_BC_VER, val);
 	}
+	bp->link_params.feature_config_flags |=
+		(val >= REQ_BC_VER_4_VRFY_OPT_MDL) ?
+		FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY : 0;
 
 	if (BP_E1HVN(bp) == 0) {
 		pci_read_config_word(bp->pdev, bp->pm_cap + PCI_PM_PMC, &pmc);
@@ -7836,6 +7858,18 @@ static void __devinit bnx2x_link_settings_supported(struct bnx2x *bp,
 					       SUPPORTED_Asym_Pause);
 			break;
 
+		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+			BNX2X_DEV_INFO("ext_phy_type 0x%x (8727)\n",
+				       ext_phy_type);
+
+			bp->port.supported |= (SUPPORTED_10000baseT_Full |
+					       SUPPORTED_1000baseT_Full |
+					       SUPPORTED_Autoneg |
+					       SUPPORTED_FIBRE |
+					       SUPPORTED_Pause |
+					       SUPPORTED_Asym_Pause);
+			break;
+
 		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
 			BNX2X_DEV_INFO("ext_phy_type 0x%x (SFX7101)\n",
 				       ext_phy_type);
@@ -8099,6 +8133,17 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp)
 	bp->link_params.ext_phy_config =
 		SHMEM_RD(bp,
 			 dev_info.port_hw_config[port].external_phy_config);
+	/* BCM8727_NOC => BCM8727 no over current */
+	if (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config) ==
+	    PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC) {
+		bp->link_params.ext_phy_config &=
+			~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
+		bp->link_params.ext_phy_config |=
+			PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727;
+		bp->link_params.feature_config_flags |=
+			FEATURE_CONFIG_BCM8727_NOC;
+	}
+
 	bp->link_params.speed_cap_mask =
 		SHMEM_RD(bp,
 			 dev_info.port_hw_config[port].speed_capability_mask);
@@ -8119,17 +8164,10 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp)
 		bp->link_params.xgxs_config_tx[(i << 1) + 1] = (val & 0xffff);
 	}
 
-	config = SHMEM_RD(bp, dev_info.port_feature_config[port].config);
-	if (config & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_ENABLED)
-		bp->link_params.feature_config_flags |=
-				FEATURE_CONFIG_MODULE_ENFORCMENT_ENABLED;
-	else
-		bp->link_params.feature_config_flags &=
-				~FEATURE_CONFIG_MODULE_ENFORCMENT_ENABLED;
-
 	/* If the device is capable of WoL, set the default state according
 	 * to the HW
 	 */
+	config = SHMEM_RD(bp, dev_info.port_feature_config[port].config);
 	bp->wol = (!(bp->flags & NO_WOL_FLAG) &&
 		   (config & PORT_FEATURE_WOL_ENABLED));
 
@@ -8139,8 +8177,8 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp)
 		       bp->link_params.ext_phy_config,
 		       bp->link_params.speed_cap_mask, bp->port.link_config);
 
-	bp->link_params.switch_cfg = (bp->port.link_config &
-				      PORT_FEATURE_CONNECTED_SWITCH_MASK);
+	bp->link_params.switch_cfg |= (bp->port.link_config &
+				       PORT_FEATURE_CONNECTED_SWITCH_MASK);
 	bnx2x_link_settings_supported(bp, bp->link_params.switch_cfg);
 
 	bnx2x_link_settings_requested(bp);
@@ -8336,6 +8374,7 @@ static int bnx2x_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
 		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
 		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+		case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
 			cmd->port = PORT_FIBRE;
 			break;