[PATCH] chelsio: working NAPI

This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 49 insertions, 66 deletions

diff --git a/drivers/net/chelsio/sge.c b/drivers/net/chelsio/sge.c
index 0ca8d876e16..659cb2252e4 100644
--- a/drivers/net/chelsio/sge.c
+++ b/drivers/net/chelsio/sge.c
@@ -1413,16 +1413,20 @@ static int sge_rx(struct sge *sge, struct freelQ *fl, unsigned int len)
 
 	if (unlikely(adapter->vlan_grp && p->vlan_valid)) {
 		st->vlan_xtract++;
-		if (adapter->params.sge.polling)
+#ifdef CONFIG_CHELSIO_T1_NAPI
 			vlan_hwaccel_receive_skb(skb, adapter->vlan_grp,
 						 ntohs(p->vlan));
-		else
+#else
 			vlan_hwaccel_rx(skb, adapter->vlan_grp,
 					ntohs(p->vlan));
-	} else if (adapter->params.sge.polling)
+#endif
+	} else {
+#ifdef CONFIG_CHELSIO_T1_NAPI
 		netif_receive_skb(skb);
-	else
+#else
 		netif_rx(skb);
+#endif
+	}
 	return 0;
 }
 
@@ -1572,6 +1576,7 @@ static int process_responses(struct adapter *adapter, int budget)
 	return budget;
 }
 
+#ifdef CONFIG_CHELSIO_T1_NAPI
 /*
  * A simpler version of process_responses() that handles only pure (i.e.,
  * non data-carrying) responses.  Such respones are too light-weight to justify
@@ -1619,92 +1624,76 @@ static int process_pure_responses(struct adapter *adapter, struct respQ_e *e)
  * or protection from interrupts as data interrupts are off at this point and
  * other adapter interrupts do not interfere.
  */
-static int t1_poll(struct net_device *dev, int *budget)
+int t1_poll(struct net_device *dev, int *budget)
 {
 	struct adapter *adapter = dev->priv;
 	int effective_budget = min(*budget, dev->quota);
-
 	int work_done = process_responses(adapter, effective_budget);
+
 	*budget -= work_done;
 	dev->quota -= work_done;
 
 	if (work_done >= effective_budget)
 		return 1;
 
+ 	spin_lock_irq(&adapter->async_lock);
 	__netif_rx_complete(dev);
-
-	/*
-	 * Because we don't atomically flush the following write it is
-	 * possible that in very rare cases it can reach the device in a way
-	 * that races with a new response being written plus an error interrupt
-	 * causing the NAPI interrupt handler below to return unhandled status
-	 * to the OS.  To protect against this would require flushing the write
-	 * and doing both the write and the flush with interrupts off.  Way too
-	 * expensive and unjustifiable given the rarity of the race.
-	 */
 	writel(adapter->sge->respQ.cidx, adapter->regs + A_SG_SLEEPING);
-	return 0;
-}
+	writel(adapter->slow_intr_mask | F_PL_INTR_SGE_DATA,
+	       adapter->regs + A_PL_ENABLE);
+ 	spin_unlock_irq(&adapter->async_lock);
 
-/*
- * Returns true if the device is already scheduled for polling.
- */
-static inline int napi_is_scheduled(struct net_device *dev)
-{
-	return test_bit(__LINK_STATE_RX_SCHED, &dev->state);
+	return 0;
 }
 
 /*
  * NAPI version of the main interrupt handler.
  */
-static irqreturn_t t1_interrupt_napi(int irq, void *data)
+irqreturn_t t1_interrupt(int irq, void *data)
 {
-	int handled;
 	struct adapter *adapter = data;
+ 	struct net_device *dev = adapter->sge->netdev;
 	struct sge *sge = adapter->sge;
-	struct respQ *q = &adapter->sge->respQ;
+ 	u32 cause;
+	int handled = 0;
 
-	/*
-	 * Clear the SGE_DATA interrupt first thing.  Normally the NAPI
-	 * handler has control of the response queue and the interrupt handler
-	 * can look at the queue reliably only once it knows NAPI is off.
-	 * We can't wait that long to clear the SGE_DATA interrupt because we
-	 * could race with t1_poll rearming the SGE interrupt, so we need to
-	 * clear the interrupt speculatively and really early on.
-	 */
-	writel(F_PL_INTR_SGE_DATA, adapter->regs + A_PL_CAUSE);
+	cause = readl(adapter->regs + A_PL_CAUSE);
+	if (cause == 0 || cause == ~0)
+		return IRQ_NONE;
 
 	spin_lock(&adapter->async_lock);
-	if (!napi_is_scheduled(sge->netdev)) {
+ 	if (cause & F_PL_INTR_SGE_DATA) {
+		struct respQ *q = &adapter->sge->respQ;
 		struct respQ_e *e = &q->entries[q->cidx];
 
-		if (e->GenerationBit == q->genbit) {
-			if (e->DataValid ||
-			    process_pure_responses(adapter, e)) {
-				if (likely(__netif_rx_schedule_prep(sge->netdev)))
-					__netif_rx_schedule(sge->netdev);
-				else if (net_ratelimit())
-					printk(KERN_INFO
-					       "NAPI schedule failure!\n");
-			} else
-				writel(q->cidx, adapter->regs + A_SG_SLEEPING);
-
-			handled = 1;
-			goto unlock;
-		} else
-			writel(q->cidx, adapter->regs + A_SG_SLEEPING);
-	}  else if (readl(adapter->regs + A_PL_CAUSE) & F_PL_INTR_SGE_DATA) {
-	        printk(KERN_ERR "data interrupt while NAPI running\n");
-	}
-	
-	handled = t1_slow_intr_handler(adapter);
+ 		handled = 1;
+ 		writel(F_PL_INTR_SGE_DATA, adapter->regs + A_PL_CAUSE);
+
+		if (e->GenerationBit == q->genbit &&
+		    __netif_rx_schedule_prep(dev)) {
+			if (e->DataValid || process_pure_responses(adapter, e)) {
+				/* mask off data IRQ */
+				writel(adapter->slow_intr_mask,
+				       adapter->regs + A_PL_ENABLE);
+				__netif_rx_schedule(sge->netdev);
+				goto unlock;
+			}
+			/* no data, no NAPI needed */
+			netif_poll_enable(dev);
+
+		}
+		writel(q->cidx, adapter->regs + A_SG_SLEEPING);
+	} else
+		handled = t1_slow_intr_handler(adapter);
+
 	if (!handled)
 		sge->stats.unhandled_irqs++;
- unlock:
+unlock:
 	spin_unlock(&adapter->async_lock);
 	return IRQ_RETVAL(handled != 0);
 }
 
+#else
 /*
  * Main interrupt handler, optimized assuming that we took a 'DATA'
  * interrupt.
@@ -1720,7 +1709,7 @@ static irqreturn_t t1_interrupt_napi(int irq, void *data)
  * 5. If we took an interrupt, but no valid respQ descriptors was found we
  *      let the slow_intr_handler run and do error handling.
  */
-static irqreturn_t t1_interrupt(int irq, void *cookie)
+irqreturn_t t1_interrupt(int irq, void *cookie)
 {
 	int work_done;
 	struct respQ_e *e;
@@ -1752,11 +1741,7 @@ static irqreturn_t t1_interrupt(int irq, void *cookie)
 	spin_unlock(&adapter->async_lock);
 	return IRQ_RETVAL(work_done != 0);
 }
-
-irq_handler_t t1_select_intr_handler(adapter_t *adapter)
-{
-	return adapter->params.sge.polling ? t1_interrupt_napi : t1_interrupt;
-}
+#endif
 
 /*
  * Enqueues the sk_buff onto the cmdQ[qid] and has hardware fetch it.
@@ -2033,7 +2018,6 @@ static void sge_tx_reclaim_cb(unsigned long data)
  */
 int t1_sge_set_coalesce_params(struct sge *sge, struct sge_params *p)
 {
-	sge->netdev->poll = t1_poll;
 	sge->fixed_intrtimer = p->rx_coalesce_usecs *
 		core_ticks_per_usec(sge->adapter);
 	writel(sge->fixed_intrtimer, sge->adapter->regs + A_SG_INTRTIMER);
@@ -2234,7 +2218,6 @@ struct sge * __devinit t1_sge_create(struct adapter *adapter,
 
 	p->coalesce_enable = 0;
 	p->sample_interval_usecs = 0;
-	p->polling = 0;
 
 	return sge;
 nomem_port: