cxgb3: More flexible support for PHY interrupts.

Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up.  Allows boards to specify interrupt GPIs though the PHYs don't
use them.

Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 21 insertions, 16 deletions

diff --git a/drivers/net/cxgb3/t3_hw.c b/drivers/net/cxgb3/t3_hw.c
index f7ced324227..bfce761156a 100644
--- a/drivers/net/cxgb3/t3_hw.c
+++ b/drivers/net/cxgb3/t3_hw.c
@@ -445,24 +445,22 @@ int t3_set_phy_speed_duplex(struct cphy *phy, int speed, int duplex)
 static const struct adapter_info t3_adap_info[] = {
 	{2, 0,
 	 F_GPIO2_OEN | F_GPIO4_OEN |
-	 F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
-	 0,
+	 F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
 	 &mi1_mdio_ops, "Chelsio PE9000"},
 	{2, 0,
 	 F_GPIO2_OEN | F_GPIO4_OEN |
-	 F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
-	 0,
+	 F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
 	 &mi1_mdio_ops, "Chelsio T302"},
 	{1, 0,
 	 F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN | F_GPIO10_OEN |
 	 F_GPIO11_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
-	 0, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+	 { 0 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
 	 &mi1_mdio_ext_ops, "Chelsio T310"},
 	{2, 0,
 	 F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO5_OEN | F_GPIO6_OEN |
 	 F_GPIO7_OEN | F_GPIO10_OEN | F_GPIO11_OEN | F_GPIO1_OUT_VAL |
-	 F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
-	 SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+	 F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
+	 { S_GPIO9, S_GPIO3 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
 	 &mi1_mdio_ext_ops, "Chelsio T320"},
 };
 
@@ -1684,19 +1682,15 @@ static int mac_intr_handler(struct adapter *adap, unsigned int idx)
  */
 int t3_phy_intr_handler(struct adapter *adapter)
 {
-	u32 mask, gpi = adapter_info(adapter)->gpio_intr;
 	u32 i, cause = t3_read_reg(adapter, A_T3DBG_INT_CAUSE);
 
 	for_each_port(adapter, i) {
 		struct port_info *p = adap2pinfo(adapter, i);
 
-		mask = gpi - (gpi & (gpi - 1));
-		gpi -= mask;
-
 		if (!(p->phy.caps & SUPPORTED_IRQ))
 			continue;
 
-		if (cause & mask) {
+		if (cause & (1 << adapter_info(adapter)->gpio_intr[i])) {
 			int phy_cause = p->phy.ops->intr_handler(&p->phy);
 
 			if (phy_cause & cphy_cause_link_change)
@@ -1765,6 +1759,17 @@ int t3_slow_intr_handler(struct adapter *adapter)
 	return 1;
 }
 
+static unsigned int calc_gpio_intr(struct adapter *adap)
+{
+	unsigned int i, gpi_intr = 0;
+
+	for_each_port(adap, i)
+		if ((adap2pinfo(adap, i)->phy.caps & SUPPORTED_IRQ) &&
+		    adapter_info(adap)->gpio_intr[i])
+			gpi_intr |= 1 << adapter_info(adap)->gpio_intr[i];
+	return gpi_intr;
+}
+
 /**
  *	t3_intr_enable - enable interrupts
  *	@adapter: the adapter whose interrupts should be enabled
@@ -1807,10 +1812,8 @@ void t3_intr_enable(struct adapter *adapter)
 		t3_write_reg(adapter, A_ULPTX_INT_ENABLE, ULPTX_INTR_MASK);
 	}
 
-	t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW,
-		     adapter_info(adapter)->gpio_intr);
-	t3_write_reg(adapter, A_T3DBG_INT_ENABLE,
-		     adapter_info(adapter)->gpio_intr);
+	t3_write_reg(adapter, A_T3DBG_INT_ENABLE, calc_gpio_intr(adapter));
+
 	if (is_pcie(adapter))
 		t3_write_reg(adapter, A_PCIE_INT_ENABLE, PCIE_INTR_MASK);
 	else
@@ -3331,6 +3334,8 @@ int t3_init_hw(struct adapter *adapter, u32 fw_params)
 	init_hw_for_avail_ports(adapter, adapter->params.nports);
 	t3_sge_init(adapter, &adapter->params.sge);
 
+	t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW, calc_gpio_intr(adapter));
+
 	t3_write_reg(adapter, A_CIM_HOST_ACC_DATA, vpd->uclk | fw_params);
 	t3_write_reg(adapter, A_CIM_BOOT_CFG,
 		     V_BOOTADDR(FW_FLASH_BOOT_ADDR >> 2));