s2io: remove lro parameter

Remove "lro" parameter of s2io driver.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: jon.mason@exar.com
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 9 insertions, 20 deletions

diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index 5f062ddfd5c..7061fc8e99c 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -38,8 +38,6 @@
  * Tx descriptors that can be associated with each corresponding FIFO.
  * intr_type: This defines the type of interrupt. The values can be 0(INTA),
  *     2(MSI_X). Default value is '2(MSI_X)'
- * lro: Specifies whether to enable Large Receive Offload (LRO) or not.
- *     Possible values '1' for enable '0' for disable. Default is '0'
  * lro_max_pkts: This parameter defines maximum number of packets can be
  *     aggregated as a single large packet
  * napi: This parameter used to enable/disable NAPI (polling Rx)
@@ -496,8 +494,6 @@ S2IO_PARM_INT(rxsync_frequency, 3);
 /* Interrupt type. Values can be 0(INTA), 2(MSI_X) */
 S2IO_PARM_INT(intr_type, 2);
 /* Large receive offload feature */
-static unsigned int lro_enable = 1;
-module_param_named(lro, lro_enable, uint, 0);
 
 /* Max pkts to be aggregated by LRO at one time. If not specified,
  * aggregation happens until we hit max IP pkt size(64K)
@@ -6733,13 +6729,10 @@ static int s2io_ethtool_set_flags(struct net_device *dev, u32 data)
 		return -EINVAL;
 
 	if (data & ETH_FLAG_LRO) {
-		if (lro_enable) {
-			if (!(dev->features & NETIF_F_LRO)) {
-				dev->features |= NETIF_F_LRO;
-				changed = 1;
-			}
-		} else
-			rc = -EINVAL;
+		if (!(dev->features & NETIF_F_LRO)) {
+			dev->features |= NETIF_F_LRO;
+			changed = 1;
+		}
 	} else if (dev->features & NETIF_F_LRO) {
 		dev->features &= ~NETIF_F_LRO;
 		changed = 1;
@@ -6748,7 +6741,6 @@ static int s2io_ethtool_set_flags(struct net_device *dev, u32 data)
 	if (changed && netif_running(dev)) {
 		s2io_stop_all_tx_queue(sp);
 		s2io_card_down(sp);
-		sp->lro = !!(dev->features & NETIF_F_LRO);
 		rc = s2io_card_up(sp);
 		if (rc)
 			s2io_reset(sp);
@@ -7305,7 +7297,7 @@ static int s2io_card_up(struct s2io_nic *sp)
 		struct ring_info *ring = &mac_control->rings[i];
 
 		ring->mtu = dev->mtu;
-		ring->lro = sp->lro;
+		ring->lro = !!(dev->features & NETIF_F_LRO);
 		ret = fill_rx_buffers(sp, ring, 1);
 		if (ret) {
 			DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
@@ -7339,7 +7331,7 @@ static int s2io_card_up(struct s2io_nic *sp)
 	/* Setting its receive mode */
 	s2io_set_multicast(dev);
 
-	if (sp->lro) {
+	if (dev->features & NETIF_F_LRO) {
 		/* Initialize max aggregatable pkts per session based on MTU */
 		sp->lro_max_aggr_per_sess = ((1<<16) - 1) / dev->mtu;
 		/* Check if we can use (if specified) user provided value */
@@ -7909,7 +7901,6 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
 	else
 		sp->device_type = XFRAME_I_DEVICE;
 
-	sp->lro = lro_enable;
 
 	/* Initialize some PCI/PCI-X fields of the NIC. */
 	s2io_init_pci(sp);
@@ -8045,8 +8036,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
 	dev->netdev_ops = &s2io_netdev_ops;
 	SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
 	dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
-	if (lro_enable)
-		dev->features |= NETIF_F_LRO;
+	dev->features |= NETIF_F_LRO;
 	dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
 	if (sp->high_dma_flag == true)
 		dev->features |= NETIF_F_HIGHDMA;
@@ -8281,9 +8271,8 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
 			  dev->name);
 	}
 
-	if (sp->lro)
-		DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
-			  dev->name);
+	DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
+		  dev->name);
 	if (ufo)
 		DBG_PRINT(ERR_DBG,
 			  "%s: UDP Fragmentation Offload(UFO) enabled\n",