sfc: Move the Solarflare drivers

Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.

CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 0 insertions, 99 deletions

diff --git a/drivers/net/sfc/spi.h b/drivers/net/sfc/spi.h
deleted file mode 100644
index 71f2e3ebe1c..00000000000
--- a/drivers/net/sfc/spi.h
+++ /dev/null
@@ -1,99 +0,0 @@
-/****************************************************************************
- * Driver for Solarflare Solarstorm network controllers and boards
- * Copyright 2005 Fen Systems Ltd.
- * Copyright 2006-2010 Solarflare Communications Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation, incorporated herein by reference.
- */
-
-#ifndef EFX_SPI_H
-#define EFX_SPI_H
-
-#include "net_driver.h"
-
-/**************************************************************************
- *
- * Basic SPI command set and bit definitions
- *
- *************************************************************************/
-
-#define SPI_WRSR 0x01		/* Write status register */
-#define SPI_WRITE 0x02		/* Write data to memory array */
-#define SPI_READ 0x03		/* Read data from memory array */
-#define SPI_WRDI 0x04		/* Reset write enable latch */
-#define SPI_RDSR 0x05		/* Read status register */
-#define SPI_WREN 0x06		/* Set write enable latch */
-#define SPI_SST_EWSR 0x50	/* SST: Enable write to status register */
-
-#define SPI_STATUS_WPEN 0x80	/* Write-protect pin enabled */
-#define SPI_STATUS_BP2 0x10	/* Block protection bit 2 */
-#define SPI_STATUS_BP1 0x08	/* Block protection bit 1 */
-#define SPI_STATUS_BP0 0x04	/* Block protection bit 0 */
-#define SPI_STATUS_WEN 0x02	/* State of the write enable latch */
-#define SPI_STATUS_NRDY 0x01	/* Device busy flag */
-
-/**
- * struct efx_spi_device - an Efx SPI (Serial Peripheral Interface) device
- * @device_id:		Controller's id for the device
- * @size:		Size (in bytes)
- * @addr_len:		Number of address bytes in read/write commands
- * @munge_address:	Flag whether addresses should be munged.
- *	Some devices with 9-bit addresses (e.g. AT25040A EEPROM)
- *	use bit 3 of the command byte as address bit A8, rather
- *	than having a two-byte address.  If this flag is set, then
- *	commands should be munged in this way.
- * @erase_command:	Erase command (or 0 if sector erase not needed).
- * @erase_size:		Erase sector size (in bytes)
- *	Erase commands affect sectors with this size and alignment.
- *	This must be a power of two.
- * @block_size:		Write block size (in bytes).
- *	Write commands are limited to blocks with this size and alignment.
- */
-struct efx_spi_device {
-	int device_id;
-	unsigned int size;
-	unsigned int addr_len;
-	unsigned int munge_address:1;
-	u8 erase_command;
-	unsigned int erase_size;
-	unsigned int block_size;
-};
-
-static inline bool efx_spi_present(const struct efx_spi_device *spi)
-{
-	return spi->size != 0;
-}
-
-int falcon_spi_cmd(struct efx_nic *efx,
-		   const struct efx_spi_device *spi, unsigned int command,
-		   int address, const void* in, void *out, size_t len);
-int falcon_spi_wait_write(struct efx_nic *efx,
-			  const struct efx_spi_device *spi);
-int falcon_spi_read(struct efx_nic *efx,
-		    const struct efx_spi_device *spi, loff_t start,
-		    size_t len, size_t *retlen, u8 *buffer);
-int falcon_spi_write(struct efx_nic *efx,
-		     const struct efx_spi_device *spi, loff_t start,
-		     size_t len, size_t *retlen, const u8 *buffer);
-
-/*
- * SFC4000 flash is partitioned into:
- *     0-0x400       chip and board config (see falcon_hwdefs.h)
- *     0x400-0x8000  unused (or may contain VPD if EEPROM not present)
- *     0x8000-end    boot code (mapped to PCI expansion ROM)
- * SFC4000 small EEPROM (size < 0x400) is used for VPD only.
- * SFC4000 large EEPROM (size >= 0x400) is partitioned into:
- *     0-0x400       chip and board config
- *     configurable  VPD
- *     0x800-0x1800  boot config
- * Aside from the chip and board config, all of these are optional and may
- * be absent or truncated depending on the devices used.
- */
-#define FALCON_NVCONFIG_END 0x400U
-#define FALCON_FLASH_BOOTCODE_START 0x8000U
-#define EFX_EEPROM_BOOTCONFIG_START 0x800U
-#define EFX_EEPROM_BOOTCONFIG_END 0x1800U
-
-#endif /* EFX_SPI_H */