Auto-update from upstream

1 files changed, 1922 insertions, 0 deletions

diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
new file mode 100644
index 00000000000..95518921001
--- /dev/null
+++ b/drivers/net/sky2.h
@@ -0,0 +1,1922 @@
+/*
+ * Definitions for the new Marvell Yukon 2 driver.
+ */
+#ifndef _SKY2_H
+#define _SKY2_H
+
+/* PCI config registers */
+#define PCI_DEV_REG1	0x40
+#define PCI_DEV_REG2	0x44
+#define PCI_DEV_STATUS  0x7c
+#define PCI_OS_PCI_X    (1<<26)
+
+#define PEX_LNK_STAT	0xf2
+#define PEX_UNC_ERR_STAT 0x104
+#define PEX_DEV_CTRL	0xe8
+
+/* Yukon-2 */
+enum pci_dev_reg_1 {
+	PCI_Y2_PIG_ENA	 = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
+	PCI_Y2_DLL_DIS	 = 1<<30, /* Disable PCI DLL (YUKON-2) */
+	PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
+	PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
+	PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
+	PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
+};
+
+enum pci_dev_reg_2 {
+	PCI_VPD_WR_THR	= 0xffL<<24,	/* Bit 31..24:	VPD Write Threshold */
+	PCI_DEV_SEL	= 0x7fL<<17,	/* Bit 23..17:	EEPROM Device Select */
+	PCI_VPD_ROM_SZ	= 7L<<14,	/* Bit 16..14:	VPD ROM Size	*/
+
+	PCI_PATCH_DIR	= 0xfL<<8,	/* Bit 11.. 8:	Ext Patches dir 3..0 */
+	PCI_EXT_PATCHS	= 0xfL<<4,	/* Bit	7.. 4:	Extended Patches 3..0 */
+	PCI_EN_DUMMY_RD	= 1<<3,		/* Enable Dummy Read */
+	PCI_REV_DESC	= 1<<2,		/* Reverse Desc. Bytes */
+
+	PCI_USEDATA64	= 1<<0,		/* Use 64Bit Data bus ext */
+};
+
+
+#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
+			       PCI_STATUS_SIG_SYSTEM_ERROR | \
+			       PCI_STATUS_REC_MASTER_ABORT | \
+			       PCI_STATUS_REC_TARGET_ABORT | \
+			       PCI_STATUS_PARITY)
+
+enum pex_dev_ctrl {
+	PEX_DC_MAX_RRS_MSK	= 7<<12, /* Bit 14..12:	Max. Read Request Size */
+	PEX_DC_EN_NO_SNOOP	= 1<<11,/* Enable No Snoop */
+	PEX_DC_EN_AUX_POW	= 1<<10,/* Enable AUX Power */
+	PEX_DC_EN_PHANTOM	= 1<<9,	/* Enable Phantom Functions */
+	PEX_DC_EN_EXT_TAG	= 1<<8,	/* Enable Extended Tag Field */
+	PEX_DC_MAX_PLS_MSK	= 7<<5,	/* Bit  7.. 5:	Max. Payload Size Mask */
+	PEX_DC_EN_REL_ORD	= 1<<4,	/* Enable Relaxed Ordering */
+	PEX_DC_EN_UNS_RQ_RP	= 1<<3,	/* Enable Unsupported Request Reporting */
+	PEX_DC_EN_FAT_ER_RP	= 1<<2,	/* Enable Fatal Error Reporting */
+	PEX_DC_EN_NFA_ER_RP	= 1<<1,	/* Enable Non-Fatal Error Reporting */
+	PEX_DC_EN_COR_ER_RP	= 1<<0,	/* Enable Correctable Error Reporting */
+};
+#define  PEX_DC_MAX_RD_RQ_SIZE(x) (((x)<<12) & PEX_DC_MAX_RRS_MSK)
+
+/* PEX_UNC_ERR_STAT	 PEX Uncorrectable Errors Status Register (Yukon-2) */
+enum pex_err {
+	PEX_UNSUP_REQ 	= 1<<20, /* Unsupported Request Error */
+
+	PEX_MALFOR_TLP	= 1<<18, /* Malformed TLP */
+
+	PEX_UNEXP_COMP	= 1<<16, /* Unexpected Completion */
+
+	PEX_COMP_TO	= 1<<14, /* Completion Timeout */
+	PEX_FLOW_CTRL_P	= 1<<13, /* Flow Control Protocol Error */
+	PEX_POIS_TLP	= 1<<12, /* Poisoned TLP */
+
+	PEX_DATA_LINK_P = 1<<4,	/* Data Link Protocol Error */
+	PEX_FATAL_ERRORS= (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P),
+};
+
+
+enum csr_regs {
+	B0_RAP		= 0x0000,
+	B0_CTST		= 0x0004,
+	B0_Y2LED	= 0x0005,
+	B0_POWER_CTRL	= 0x0007,
+	B0_ISRC		= 0x0008,
+	B0_IMSK		= 0x000c,
+	B0_HWE_ISRC	= 0x0010,
+	B0_HWE_IMSK	= 0x0014,
+
+	/* Special ISR registers (Yukon-2 only) */
+	B0_Y2_SP_ISRC2	= 0x001c,
+	B0_Y2_SP_ISRC3	= 0x0020,
+	B0_Y2_SP_EISR	= 0x0024,
+	B0_Y2_SP_LISR	= 0x0028,
+	B0_Y2_SP_ICR	= 0x002c,
+
+	B2_MAC_1	= 0x0100,
+	B2_MAC_2	= 0x0108,
+	B2_MAC_3	= 0x0110,
+	B2_CONN_TYP	= 0x0118,
+	B2_PMD_TYP	= 0x0119,
+	B2_MAC_CFG	= 0x011a,
+	B2_CHIP_ID	= 0x011b,
+	B2_E_0		= 0x011c,
+
+	B2_Y2_CLK_GATE  = 0x011d,
+	B2_Y2_HW_RES	= 0x011e,
+	B2_E_3		= 0x011f,
+	B2_Y2_CLK_CTRL	= 0x0120,
+
+	B2_TI_INI	= 0x0130,
+	B2_TI_VAL	= 0x0134,
+	B2_TI_CTRL	= 0x0138,
+	B2_TI_TEST	= 0x0139,
+
+	B2_TST_CTRL1	= 0x0158,
+	B2_TST_CTRL2	= 0x0159,
+	B2_GP_IO	= 0x015c,
+
+	B2_I2C_CTRL	= 0x0160,
+	B2_I2C_DATA	= 0x0164,
+	B2_I2C_IRQ	= 0x0168,
+	B2_I2C_SW	= 0x016c,
+
+	B3_RAM_ADDR	= 0x0180,
+	B3_RAM_DATA_LO	= 0x0184,
+	B3_RAM_DATA_HI	= 0x0188,
+
+/* RAM Interface Registers */
+/* Yukon-2: use RAM_BUFFER() to access the RAM buffer */
+/*
+ * The HW-Spec. calls this registers Timeout Value 0..11. But this names are
+ * not usable in SW. Please notice these are NOT real timeouts, these are
+ * the number of qWords transferred continuously.
+ */
+#define RAM_BUFFER(port, reg)	(reg | (port <<6))
+
+	B3_RI_WTO_R1	= 0x0190,
+	B3_RI_WTO_XA1	= 0x0191,
+	B3_RI_WTO_XS1	= 0x0192,
+	B3_RI_RTO_R1	= 0x0193,
+	B3_RI_RTO_XA1	= 0x0194,
+	B3_RI_RTO_XS1	= 0x0195,
+	B3_RI_WTO_R2	= 0x0196,
+	B3_RI_WTO_XA2	= 0x0197,
+	B3_RI_WTO_XS2	= 0x0198,
+	B3_RI_RTO_R2	= 0x0199,
+	B3_RI_RTO_XA2	= 0x019a,
+	B3_RI_RTO_XS2	= 0x019b,
+	B3_RI_TO_VAL	= 0x019c,
+	B3_RI_CTRL	= 0x01a0,
+	B3_RI_TEST	= 0x01a2,
+	B3_MA_TOINI_RX1	= 0x01b0,
+	B3_MA_TOINI_RX2	= 0x01b1,
+	B3_MA_TOINI_TX1	= 0x01b2,
+	B3_MA_TOINI_TX2	= 0x01b3,
+	B3_MA_TOVAL_RX1	= 0x01b4,
+	B3_MA_TOVAL_RX2	= 0x01b5,
+	B3_MA_TOVAL_TX1	= 0x01b6,
+	B3_MA_TOVAL_TX2	= 0x01b7,
+	B3_MA_TO_CTRL	= 0x01b8,
+	B3_MA_TO_TEST	= 0x01ba,
+	B3_MA_RCINI_RX1	= 0x01c0,
+	B3_MA_RCINI_RX2	= 0x01c1,
+	B3_MA_RCINI_TX1	= 0x01c2,
+	B3_MA_RCINI_TX2	= 0x01c3,
+	B3_MA_RCVAL_RX1	= 0x01c4,
+	B3_MA_RCVAL_RX2	= 0x01c5,
+	B3_MA_RCVAL_TX1	= 0x01c6,
+	B3_MA_RCVAL_TX2	= 0x01c7,
+	B3_MA_RC_CTRL	= 0x01c8,
+	B3_MA_RC_TEST	= 0x01ca,
+	B3_PA_TOINI_RX1	= 0x01d0,
+	B3_PA_TOINI_RX2	= 0x01d4,
+	B3_PA_TOINI_TX1	= 0x01d8,
+	B3_PA_TOINI_TX2	= 0x01dc,
+	B3_PA_TOVAL_RX1	= 0x01e0,
+	B3_PA_TOVAL_RX2	= 0x01e4,
+	B3_PA_TOVAL_TX1	= 0x01e8,
+	B3_PA_TOVAL_TX2	= 0x01ec,
+	B3_PA_CTRL	= 0x01f0,
+	B3_PA_TEST	= 0x01f2,
+
+	Y2_CFG_SPC	= 0x1c00,
+};
+
+/*	B0_CTST			16 bit	Control/Status register */
+enum {
+	Y2_VMAIN_AVAIL	= 1<<17,/* VMAIN available (YUKON-2 only) */
+	Y2_VAUX_AVAIL	= 1<<16,/* VAUX available (YUKON-2 only) */
+	Y2_ASF_ENABLE	= 1<<13,/* ASF Unit Enable (YUKON-2 only) */
+	Y2_ASF_DISABLE	= 1<<12,/* ASF Unit Disable (YUKON-2 only) */
+	Y2_CLK_RUN_ENA	= 1<<11,/* CLK_RUN Enable  (YUKON-2 only) */
+	Y2_CLK_RUN_DIS	= 1<<10,/* CLK_RUN Disable (YUKON-2 only) */
+	Y2_LED_STAT_ON	= 1<<9, /* Status LED On  (YUKON-2 only) */
+	Y2_LED_STAT_OFF	= 1<<8, /* Status LED Off (YUKON-2 only) */
+
+	CS_ST_SW_IRQ	= 1<<7,	/* Set IRQ SW Request */
+	CS_CL_SW_IRQ	= 1<<6,	/* Clear IRQ SW Request */
+	CS_STOP_DONE	= 1<<5,	/* Stop Master is finished */
+	CS_STOP_MAST	= 1<<4,	/* Command Bit to stop the master */
+	CS_MRST_CLR	= 1<<3,	/* Clear Master reset	*/
+	CS_MRST_SET	= 1<<2,	/* Set Master reset	*/
+	CS_RST_CLR	= 1<<1,	/* Clear Software reset	*/
+	CS_RST_SET	= 1,	/* Set   Software reset	*/
+};
+
+/*	B0_LED			 8 Bit	LED register */
+enum {
+/* Bit  7.. 2:	reserved */
+	LED_STAT_ON	= 1<<1,	/* Status LED on	*/
+	LED_STAT_OFF	= 1,	/* Status LED off	*/
+};
+
+/*	B0_POWER_CTRL	 8 Bit	Power Control reg (YUKON only) */
+enum {
+	PC_VAUX_ENA	= 1<<7,	/* Switch VAUX Enable  */
+	PC_VAUX_DIS	= 1<<6,	/* Switch VAUX Disable */
+	PC_VCC_ENA	= 1<<5,	/* Switch VCC Enable  */
+	PC_VCC_DIS	= 1<<4,	/* Switch VCC Disable */
+	PC_VAUX_ON	= 1<<3,	/* Switch VAUX On  */
+	PC_VAUX_OFF	= 1<<2,	/* Switch VAUX Off */
+	PC_VCC_ON	= 1<<1,	/* Switch VCC On  */
+	PC_VCC_OFF	= 1<<0,	/* Switch VCC Off */
+};
+
+/*	B2_IRQM_MSK 	32 bit	IRQ Moderation Mask */
+
+/*	B0_Y2_SP_ISRC2	32 bit	Special Interrupt Source Reg 2 */
+/*	B0_Y2_SP_ISRC3	32 bit	Special Interrupt Source Reg 3 */
+/*	B0_Y2_SP_EISR	32 bit	Enter ISR Reg */
+/*	B0_Y2_SP_LISR	32 bit	Leave ISR Reg */
+enum {
+	Y2_IS_HW_ERR	= 1<<31,	/* Interrupt HW Error */
+	Y2_IS_STAT_BMU	= 1<<30,	/* Status BMU Interrupt */
+	Y2_IS_ASF	= 1<<29,	/* ASF subsystem Interrupt */
+
+	Y2_IS_POLL_CHK	= 1<<27,	/* Check IRQ from polling unit */
+	Y2_IS_TWSI_RDY	= 1<<26,	/* IRQ on end of TWSI Tx */
+	Y2_IS_IRQ_SW	= 1<<25,	/* SW forced IRQ	*/
+	Y2_IS_TIMINT	= 1<<24,	/* IRQ from Timer	*/
+
+	Y2_IS_IRQ_PHY2	= 1<<12,	/* Interrupt from PHY 2 */
+	Y2_IS_IRQ_MAC2	= 1<<11,	/* Interrupt from MAC 2 */
+	Y2_IS_CHK_RX2	= 1<<10,	/* Descriptor error Rx 2 */
+	Y2_IS_CHK_TXS2	= 1<<9,		/* Descriptor error TXS 2 */
+	Y2_IS_CHK_TXA2	= 1<<8,		/* Descriptor error TXA 2 */
+
+	Y2_IS_IRQ_PHY1	= 1<<4,		/* Interrupt from PHY 1 */
+	Y2_IS_IRQ_MAC1	= 1<<3,		/* Interrupt from MAC 1 */
+	Y2_IS_CHK_RX1	= 1<<2,		/* Descriptor error Rx 1 */
+	Y2_IS_CHK_TXS1	= 1<<1,		/* Descriptor error TXS 1 */
+	Y2_IS_CHK_TXA1	= 1<<0,		/* Descriptor error TXA 1 */
+
+	Y2_IS_BASE	= Y2_IS_HW_ERR | Y2_IS_STAT_BMU |
+			  Y2_IS_POLL_CHK | Y2_IS_TWSI_RDY |
+			  Y2_IS_IRQ_SW | Y2_IS_TIMINT,
+	Y2_IS_PORT_1	= Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 |
+			  Y2_IS_CHK_RX1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_TXS1,
+	Y2_IS_PORT_2	= Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 |
+			  Y2_IS_CHK_RX2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_TXS2,
+};
+
+/*	B2_IRQM_HWE_MSK	32 bit	IRQ Moderation HW Error Mask */
+enum {
+	IS_ERR_MSK	= 0x00003fff,/* 		All Error bits */
+
+	IS_IRQ_TIST_OV	= 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
+	IS_IRQ_SENSOR	= 1<<12, /* IRQ from Sensor (YUKON only) */
+	IS_IRQ_MST_ERR	= 1<<11, /* IRQ master error detected */
+	IS_IRQ_STAT	= 1<<10, /* IRQ status exception */
+	IS_NO_STAT_M1	= 1<<9,	/* No Rx Status from MAC 1 */
+	IS_NO_STAT_M2	= 1<<8,	/* No Rx Status from MAC 2 */
+	IS_NO_TIST_M1	= 1<<7,	/* No Time Stamp from MAC 1 */
+	IS_NO_TIST_M2	= 1<<6,	/* No Time Stamp from MAC 2 */
+	IS_RAM_RD_PAR	= 1<<5,	/* RAM Read  Parity Error */
+	IS_RAM_WR_PAR	= 1<<4,	/* RAM Write Parity Error */
+	IS_M1_PAR_ERR	= 1<<3,	/* MAC 1 Parity Error */
+	IS_M2_PAR_ERR	= 1<<2,	/* MAC 2 Parity Error */
+	IS_R1_PAR_ERR	= 1<<1,	/* Queue R1 Parity Error */
+	IS_R2_PAR_ERR	= 1<<0,	/* Queue R2 Parity Error */
+};
+
+/* Hardware error interrupt mask for Yukon 2 */
+enum {
+	Y2_IS_TIST_OV	= 1<<29,/* Time Stamp Timer overflow interrupt */
+	Y2_IS_SENSOR	= 1<<28, /* Sensor interrupt */
+	Y2_IS_MST_ERR	= 1<<27, /* Master error interrupt */
+	Y2_IS_IRQ_STAT	= 1<<26, /* Status exception interrupt */
+	Y2_IS_PCI_EXP	= 1<<25, /* PCI-Express interrupt */
+	Y2_IS_PCI_NEXP	= 1<<24, /* PCI-Express error similar to PCI error */
+						/* Link 2 */
+	Y2_IS_PAR_RD2	= 1<<13, /* Read RAM parity error interrupt */
+	Y2_IS_PAR_WR2	= 1<<12, /* Write RAM parity error interrupt */
+	Y2_IS_PAR_MAC2	= 1<<11, /* MAC hardware fault interrupt */
+	Y2_IS_PAR_RX2	= 1<<10, /* Parity Error Rx Queue 2 */
+	Y2_IS_TCP_TXS2	= 1<<9, /* TCP length mismatch sync Tx queue IRQ */
+	Y2_IS_TCP_TXA2	= 1<<8, /* TCP length mismatch async Tx queue IRQ */
+						/* Link 1 */
+	Y2_IS_PAR_RD1	= 1<<5, /* Read RAM parity error interrupt */
+	Y2_IS_PAR_WR1	= 1<<4, /* Write RAM parity error interrupt */
+	Y2_IS_PAR_MAC1	= 1<<3, /* MAC hardware fault interrupt */
+	Y2_IS_PAR_RX1	= 1<<2, /* Parity Error Rx Queue 1 */
+	Y2_IS_TCP_TXS1	= 1<<1, /* TCP length mismatch sync Tx queue IRQ */
+	Y2_IS_TCP_TXA1	= 1<<0, /* TCP length mismatch async Tx queue IRQ */
+
+	Y2_HWE_L1_MASK	= Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 |
+			  Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1,
+	Y2_HWE_L2_MASK	= Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 |
+			  Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
+
+	Y2_HWE_ALL_MASK	= Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
+			  Y2_IS_PCI_EXP |
+			  Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
+};
+
+/*	B28_DPT_CTRL	 8 bit	Descriptor Poll Timer Ctrl Reg */
+enum {
+	DPT_START	= 1<<1,
+	DPT_STOP	= 1<<0,
+};
+
+/*	B2_TST_CTRL1	 8 bit	Test Control Register 1 */
+enum {
+	TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
+	TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
+	TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
+	TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
+	TST_FRC_APERR_M	 = 1<<3, /* force ADDRPERR on MST */
+	TST_FRC_APERR_T	 = 1<<2, /* force ADDRPERR on TRG */
+	TST_CFG_WRITE_ON = 1<<1, /* Enable  Config Reg WR */
+	TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
+};
+
+/*	B2_MAC_CFG		 8 bit	MAC Configuration / Chip Revision */
+enum {
+	CFG_CHIP_R_MSK	  = 0xf<<4,	/* Bit 7.. 4: Chip Revision */
+					/* Bit 3.. 2:	reserved */
+	CFG_DIS_M2_CLK	  = 1<<1,	/* Disable Clock for 2nd MAC */
+	CFG_SNG_MAC	  = 1<<0,	/* MAC Config: 0=2 MACs / 1=1 MAC*/
+};
+
+/*	B2_CHIP_ID		 8 bit 	Chip Identification Number */
+enum {
+	CHIP_ID_GENESIS	   = 0x0a, /* Chip ID for GENESIS */
+	CHIP_ID_YUKON	   = 0xb0, /* Chip ID for YUKON */
+	CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
+	CHIP_ID_YUKON_LP   = 0xb2, /* Chip ID for YUKON-LP */
+	CHIP_ID_YUKON_XL   = 0xb3, /* Chip ID for YUKON-2 XL */
+	CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
+	CHIP_ID_YUKON_EC   = 0xb6, /* Chip ID for YUKON-2 EC */
+ 	CHIP_ID_YUKON_FE   = 0xb7, /* Chip ID for YUKON-2 FE */
+
+	CHIP_REV_YU_EC_A1    = 0,  /* Chip Rev. for Yukon-EC A1/A0 */
+	CHIP_REV_YU_EC_A2    = 1,  /* Chip Rev. for Yukon-EC A2 */
+	CHIP_REV_YU_EC_A3    = 2,  /* Chip Rev. for Yukon-EC A3 */
+};
+
+/*	B2_Y2_CLK_GATE	 8 bit	Clock Gating (Yukon-2 only) */
+enum {
+	Y2_STATUS_LNK2_INAC	= 1<<7, /* Status Link 2 inactive (0 = active) */
+	Y2_CLK_GAT_LNK2_DIS	= 1<<6, /* Disable clock gating Link 2 */
+	Y2_COR_CLK_LNK2_DIS	= 1<<5, /* Disable Core clock Link 2 */
+	Y2_PCI_CLK_LNK2_DIS	= 1<<4, /* Disable PCI clock Link 2 */
+	Y2_STATUS_LNK1_INAC	= 1<<3, /* Status Link 1 inactive (0 = active) */
+	Y2_CLK_GAT_LNK1_DIS	= 1<<2, /* Disable clock gating Link 1 */
+	Y2_COR_CLK_LNK1_DIS	= 1<<1, /* Disable Core clock Link 1 */
+	Y2_PCI_CLK_LNK1_DIS	= 1<<0, /* Disable PCI clock Link 1 */
+};
+
+/*	B2_Y2_HW_RES	8 bit	HW Resources (Yukon-2 only) */
+enum {
+	CFG_LED_MODE_MSK	= 7<<2,	/* Bit  4.. 2:	LED Mode Mask */
+	CFG_LINK_2_AVAIL	= 1<<1,	/* Link 2 available */
+	CFG_LINK_1_AVAIL	= 1<<0,	/* Link 1 available */
+};
+#define CFG_LED_MODE(x)		(((x) & CFG_LED_MODE_MSK) >> 2)
+#define CFG_DUAL_MAC_MSK	(CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL)
+
+
+/* B2_Y2_CLK_CTRL	32 bit	Clock Frequency Control Register (Yukon-2/EC) */
+enum {
+	Y2_CLK_DIV_VAL_MSK	= 0xff<<16,/* Bit 23..16: Clock Divisor Value */
+#define	Y2_CLK_DIV_VAL(x)	(((x)<<16) & Y2_CLK_DIV_VAL_MSK)
+	Y2_CLK_DIV_VAL2_MSK	= 7<<21,   /* Bit 23..21: Clock Divisor Value */
+	Y2_CLK_SELECT2_MSK	= 0x1f<<16,/* Bit 20..16: Clock Select */
+#define Y2_CLK_DIV_VAL_2(x)	(((x)<<21) & Y2_CLK_DIV_VAL2_MSK)
+#define Y2_CLK_SEL_VAL_2(x)	(((x)<<16) & Y2_CLK_SELECT2_MSK)
+	Y2_CLK_DIV_ENA		= 1<<1, /* Enable  Core Clock Division */
+	Y2_CLK_DIV_DIS		= 1<<0,	/* Disable Core Clock Division */
+};
+
+/*	B2_TI_CTRL		 8 bit	Timer control */
+/*	B2_IRQM_CTRL	 8 bit	IRQ Moderation Timer Control */
+enum {
+	TIM_START	= 1<<2,	/* Start Timer */
+	TIM_STOP	= 1<<1,	/* Stop  Timer */
+	TIM_CLR_IRQ	= 1<<0,	/* Clear Timer IRQ (!IRQM) */
+};
+
+/*	B2_TI_TEST		 8 Bit	Timer Test */
+/*	B2_IRQM_TEST	 8 bit	IRQ Moderation Timer Test */
+/*	B28_DPT_TST		 8 bit	Descriptor Poll Timer Test Reg */
+enum {
+	TIM_T_ON	= 1<<2,	/* Test mode on */
+	TIM_T_OFF	= 1<<1,	/* Test mode off */
+	TIM_T_STEP	= 1<<0,	/* Test step */
+};
+
+/*	B3_RAM_ADDR		32 bit	RAM Address, to read or write */
+					/* Bit 31..19:	reserved */
+#define RAM_ADR_RAN	0x0007ffffL	/* Bit 18.. 0:	RAM Address Range */
+/* RAM Interface Registers */
+
+/*	B3_RI_CTRL		16 bit	RAM Interface Control Register */
+enum {
+	RI_CLR_RD_PERR	= 1<<9,	/* Clear IRQ RAM Read Parity Err */
+	RI_CLR_WR_PERR	= 1<<8,	/* Clear IRQ RAM Write Parity Err*/
+
+	RI_RST_CLR	= 1<<1,	/* Clear RAM Interface Reset */
+	RI_RST_SET	= 1<<0,	/* Set   RAM Interface Reset */
+};
+
+#define SK_RI_TO_53	36		/* RAM interface timeout */
+
+
+/* Port related registers FIFO, and Arbiter */
+#define SK_REG(port,reg)	(((port)<<7)+(reg))
+
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
+/*	TXA_ITI_INI		32 bit	Tx Arb Interval Timer Init Val */
+/*	TXA_ITI_VAL		32 bit	Tx Arb Interval Timer Value */
+/*	TXA_LIM_INI		32 bit	Tx Arb Limit Counter Init Val */
+/*	TXA_LIM_VAL		32 bit	Tx Arb Limit Counter Value */
+
+#define TXA_MAX_VAL	0x00ffffffUL	/* Bit 23.. 0:	Max TXA Timer/Cnt Val */
+
+/*	TXA_CTRL		 8 bit	Tx Arbiter Control Register */
+enum {
+	TXA_ENA_FSYNC	= 1<<7,	/* Enable  force of sync Tx queue */
+	TXA_DIS_FSYNC	= 1<<6,	/* Disable force of sync Tx queue */
+	TXA_ENA_ALLOC	= 1<<5,	/* Enable  alloc of free bandwidth */
+	TXA_DIS_ALLOC	= 1<<4,	/* Disable alloc of free bandwidth */
+	TXA_START_RC	= 1<<3,	/* Start sync Rate Control */
+	TXA_STOP_RC	= 1<<2,	/* Stop  sync Rate Control */
+	TXA_ENA_ARB	= 1<<1,	/* Enable  Tx Arbiter */
+	TXA_DIS_ARB	= 1<<0,	/* Disable Tx Arbiter */
+};
+
+/*
+ *	Bank 4 - 5
+ */
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
+enum {
+	TXA_ITI_INI	= 0x0200,/* 32 bit	Tx Arb Interval Timer Init Val*/
+	TXA_ITI_VAL	= 0x0204,/* 32 bit	Tx Arb Interval Timer Value */
+	TXA_LIM_INI	= 0x0208,/* 32 bit	Tx Arb Limit Counter Init Val */
+	TXA_LIM_VAL	= 0x020c,/* 32 bit	Tx Arb Limit Counter Value */
+	TXA_CTRL	= 0x0210,/*  8 bit	Tx Arbiter Control Register */
+	TXA_TEST	= 0x0211,/*  8 bit	Tx Arbiter Test Register */
+	TXA_STAT	= 0x0212,/*  8 bit	Tx Arbiter Status Register */
+};
+
+
+enum {
+	B6_EXT_REG	= 0x0300,/* External registers (GENESIS only) */
+	B7_CFG_SPC	= 0x0380,/* copy of the Configuration register */
+	B8_RQ1_REGS	= 0x0400,/* Receive Queue 1 */
+	B8_RQ2_REGS	= 0x0480,/* Receive Queue 2 */
+	B8_TS1_REGS	= 0x0600,/* Transmit sync queue 1 */
+	B8_TA1_REGS	= 0x0680,/* Transmit async queue 1 */
+	B8_TS2_REGS	= 0x0700,/* Transmit sync queue 2 */
+	B8_TA2_REGS	= 0x0780,/* Transmit sync queue 2 */
+	B16_RAM_REGS	= 0x0800,/* RAM Buffer Registers */
+};
+
+/* Queue Register Offsets, use Q_ADDR() to access */
+enum {
+	B8_Q_REGS = 0x0400, /* base of Queue registers */
+	Q_D	= 0x00,	/* 8*32	bit	Current Descriptor */
+	Q_DA_L	= 0x20,	/* 32 bit	Current Descriptor Address Low dWord */
+	Q_DA_H	= 0x24,	/* 32 bit	Current Descriptor Address High dWord */
+	Q_AC_L	= 0x28,	/* 32 bit	Current Address Counter Low dWord */
+	Q_AC_H	= 0x2c,	/* 32 bit	Current Address Counter High dWord */
+	Q_BC	= 0x30,	/* 32 bit	Current Byte Counter */
+	Q_CSR	= 0x34,	/* 32 bit	BMU Control/Status Register */
+	Q_F	= 0x38,	/* 32 bit	Flag Register */
+	Q_T1	= 0x3c,	/* 32 bit	Test Register 1 */
+	Q_T1_TR	= 0x3c,	/*  8 bit	Test Register 1 Transfer SM */
+	Q_T1_WR	= 0x3d,	/*  8 bit	Test Register 1 Write Descriptor SM */
+	Q_T1_RD	= 0x3e,	/*  8 bit	Test Register 1 Read Descriptor SM */
+	Q_T1_SV	= 0x3f,	/*  8 bit	Test Register 1 Supervisor SM */
+	Q_T2	= 0x40,	/* 32 bit	Test Register 2	*/
+	Q_T3	= 0x44,	/* 32 bit	Test Register 3	*/
+
+/* Yukon-2 */
+	Q_DONE	= 0x24,	/* 16 bit	Done Index 		(Yukon-2 only) */
+	Q_WM	= 0x40,	/* 16 bit	FIFO Watermark */
+	Q_AL	= 0x42,	/*  8 bit	FIFO Alignment */
+	Q_RSP	= 0x44,	/* 16 bit	FIFO Read Shadow Pointer */
+	Q_RSL	= 0x46,	/*  8 bit	FIFO Read Shadow Level */
+	Q_RP	= 0x48,	/*  8 bit	FIFO Read Pointer */
+	Q_RL	= 0x4a,	/*  8 bit	FIFO Read Level */
+	Q_WP	= 0x4c,	/*  8 bit	FIFO Write Pointer */
+	Q_WSP	= 0x4d,	/*  8 bit	FIFO Write Shadow Pointer */
+	Q_WL	= 0x4e,	/*  8 bit	FIFO Write Level */
+	Q_WSL	= 0x4f,	/*  8 bit	FIFO Write Shadow Level */
+};
+#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+
+
+/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
+enum {
+	Y2_B8_PREF_REGS		= 0x0450,
+
+	PREF_UNIT_CTRL		= 0x00,	/* 32 bit	Control register */
+	PREF_UNIT_LAST_IDX	= 0x04,	/* 16 bit	Last Index */
+	PREF_UNIT_ADDR_LO	= 0x08,	/* 32 bit	List start addr, low part */
+	PREF_UNIT_ADDR_HI	= 0x0c,	/* 32 bit	List start addr, high part*/
+	PREF_UNIT_GET_IDX	= 0x10,	/* 16 bit	Get Index */
+	PREF_UNIT_PUT_IDX	= 0x14,	/* 16 bit	Put Index */
+	PREF_UNIT_FIFO_WP	= 0x20,	/*  8 bit	FIFO write pointer */
+	PREF_UNIT_FIFO_RP	= 0x24,	/*  8 bit	FIFO read pointer */
+	PREF_UNIT_FIFO_WM	= 0x28,	/*  8 bit	FIFO watermark */
+	PREF_UNIT_FIFO_LEV	= 0x2c,	/*  8 bit	FIFO level */
+
+	PREF_UNIT_MASK_IDX	= 0x0fff,
+};
+#define Y2_QADDR(q,reg)		(Y2_B8_PREF_REGS + (q) + (reg))
+
+/* RAM Buffer Register Offsets */
+enum {
+
+	RB_START	= 0x00,/* 32 bit	RAM Buffer Start Address */
+	RB_END	= 0x04,/* 32 bit	RAM Buffer End Address */
+	RB_WP	= 0x08,/* 32 bit	RAM Buffer Write Pointer */
+	RB_RP	= 0x0c,/* 32 bit	RAM Buffer Read Pointer */
+	RB_RX_UTPP	= 0x10,/* 32 bit	Rx Upper Threshold, Pause Packet */
+	RB_RX_LTPP	= 0x14,/* 32 bit	Rx Lower Threshold, Pause Packet */
+	RB_RX_UTHP	= 0x18,/* 32 bit	Rx Upper Threshold, High Prio */
+	RB_RX_LTHP	= 0x1c,/* 32 bit	Rx Lower Threshold, High Prio */
+	/* 0x10 - 0x1f:	reserved at Tx RAM Buffer Registers */
+	RB_PC	= 0x20,/* 32 bit	RAM Buffer Packet Counter */
+	RB_LEV	= 0x24,/* 32 bit	RAM Buffer Level Register */
+	RB_CTRL	= 0x28,/* 32 bit	RAM Buffer Control Register */
+	RB_TST1	= 0x29,/*  8 bit	RAM Buffer Test Register 1 */
+	RB_TST2	= 0x2a,/*  8 bit	RAM Buffer Test Register 2 */
+};
+
+/* Receive and Transmit Queues */
+enum {
+	Q_R1	= 0x0000,	/* Receive Queue 1 */
+	Q_R2	= 0x0080,	/* Receive Queue 2 */
+	Q_XS1	= 0x0200,	/* Synchronous Transmit Queue 1 */
+	Q_XA1	= 0x0280,	/* Asynchronous Transmit Queue 1 */
+	Q_XS2	= 0x0300,	/* Synchronous Transmit Queue 2 */
+	Q_XA2	= 0x0380,	/* Asynchronous Transmit Queue 2 */
+};
+
+/* Different PHY Types */
+enum {
+	PHY_ADDR_MARV	= 0,
+};
+
+#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+
+
+enum {
+	LNK_SYNC_INI	= 0x0c30,/* 32 bit	Link Sync Cnt Init Value */
+	LNK_SYNC_VAL	= 0x0c34,/* 32 bit	Link Sync Cnt Current Value */
+	LNK_SYNC_CTRL	= 0x0c38,/*  8 bit	Link Sync Cnt Control Register */
+	LNK_SYNC_TST	= 0x0c39,/*  8 bit	Link Sync Cnt Test Register */
+
+	LNK_LED_REG	= 0x0c3c,/*  8 bit	Link LED Register */
+
+/* Receive GMAC FIFO (YUKON and Yukon-2) */
+
+	RX_GMF_EA	= 0x0c40,/* 32 bit	Rx GMAC FIFO End Address */
+	RX_GMF_AF_THR	= 0x0c44,/* 32 bit	Rx GMAC FIFO Almost Full Thresh. */
+	RX_GMF_CTRL_T	= 0x0c48,/* 32 bit	Rx GMAC FIFO Control/Test */
+	RX_GMF_FL_MSK	= 0x0c4c,/* 32 bit	Rx GMAC FIFO Flush Mask */
+	RX_GMF_FL_THR	= 0x0c50,/* 32 bit	Rx GMAC FIFO Flush Threshold */
+	RX_GMF_TR_THR	= 0x0c54,/* 32 bit	Rx Truncation Threshold (Yukon-2) */
+	RX_GMF_UP_THR	= 0x0c58,/*  8 bit	Rx Upper Pause Thr (Yukon-EC_U) */
+	RX_GMF_LP_THR	= 0x0c5a,/*  8 bit	Rx Lower Pause Thr (Yukon-EC_U) */
+	RX_GMF_VLAN	= 0x0c5c,/* 32 bit	Rx VLAN Type Register (Yukon-2) */
+	RX_GMF_WP	= 0x0c60,/* 32 bit	Rx GMAC FIFO Write Pointer */
+
+	RX_GMF_WLEV	= 0x0c68,/* 32 bit	Rx GMAC FIFO Write Level */
+
+	RX_GMF_RP	= 0x0c70,/* 32 bit	Rx GMAC FIFO Read Pointer */
+
+	RX_GMF_RLEV	= 0x0c78,/* 32 bit	Rx GMAC FIFO Read Level */
+};
+
+
+/*	Q_BC			32 bit	Current Byte Counter */
+
+/* BMU Control Status Registers */
+/*	B0_R1_CSR		32 bit	BMU Ctrl/Stat Rx Queue 1 */
+/*	B0_R2_CSR		32 bit	BMU Ctrl/Stat Rx Queue 2 */
+/*	B0_XA1_CSR		32 bit	BMU Ctrl/Stat Sync Tx Queue 1 */
+/*	B0_XS1_CSR		32 bit	BMU Ctrl/Stat Async Tx Queue 1 */
+/*	B0_XA2_CSR		32 bit	BMU Ctrl/Stat Sync Tx Queue 2 */
+/*	B0_XS2_CSR		32 bit	BMU Ctrl/Stat Async Tx Queue 2 */
+/*	Q_CSR			32 bit	BMU Control/Status Register */
+
+/* Rx BMU Control / Status Registers (Yukon-2) */
+enum {
+	BMU_IDLE	= 1<<31, /* BMU Idle State */
+	BMU_RX_TCP_PKT	= 1<<30, /* Rx TCP Packet (when RSS Hash enabled) */
+	BMU_RX_IP_PKT	= 1<<29, /* Rx IP  Packet (when RSS Hash enabled) */
+
+	BMU_ENA_RX_RSS_HASH = 1<<15, /* Enable  Rx RSS Hash */
+	BMU_DIS_RX_RSS_HASH = 1<<14, /* Disable Rx RSS Hash */
+	BMU_ENA_RX_CHKSUM = 1<<13, /* Enable  Rx TCP/IP Checksum Check */
+	BMU_DIS_RX_CHKSUM = 1<<12, /* Disable Rx TCP/IP Checksum Check */
+	BMU_CLR_IRQ_PAR	= 1<<11, /* Clear IRQ on Parity errors (Rx) */
+	BMU_CLR_IRQ_TCP	= 1<<11, /* Clear IRQ on TCP segment. error (Tx) */
+	BMU_CLR_IRQ_CHK	= 1<<10, /* Clear IRQ Check */
+	BMU_STOP	= 1<<9, /* Stop  Rx/Tx Queue */
+	BMU_START	= 1<<8, /* Start Rx/Tx Queue */
+	BMU_FIFO_OP_ON	= 1<<7, /* FIFO Operational On */
+	BMU_FIFO_OP_OFF	= 1<<6, /* FIFO Operational Off */
+	BMU_FIFO_ENA	= 1<<5, /* Enable FIFO */
+	BMU_FIFO_RST	= 1<<4, /* Reset  FIFO */
+	BMU_OP_ON	= 1<<3, /* BMU Operational On */
+	BMU_OP_OFF	= 1<<2, /* BMU Operational Off */
+	BMU_RST_CLR	= 1<<1, /* Clear BMU Reset (Enable) */
+	BMU_RST_SET	= 1<<0, /* Set   BMU Reset */
+
+	BMU_CLR_RESET	= BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR,
+	BMU_OPER_INIT	= BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | BMU_START |
+			  BMU_FIFO_ENA | BMU_OP_ON,
+
+	BMU_WM_DEFAULT = 0x600,
+};
+
+/* Tx BMU Control / Status Registers (Yukon-2) */
+								/* Bit 31: same as for Rx */
+enum {
+	BMU_TX_IPIDINCR_ON	= 1<<13, /* Enable  IP ID Increment */
+	BMU_TX_IPIDINCR_OFF	= 1<<12, /* Disable IP ID Increment */
+	BMU_TX_CLR_IRQ_TCP	= 1<<11, /* Clear IRQ on TCP segment length mismatch */
+};
+
+/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
+/* PREF_UNIT_CTRL	32 bit	Prefetch Control register */
+enum {
+	PREF_UNIT_OP_ON		= 1<<3,	/* prefetch unit operational */
+	PREF_UNIT_OP_OFF	= 1<<2,	/* prefetch unit not operational */
+	PREF_UNIT_RST_CLR	= 1<<1,	/* Clear Prefetch Unit Reset */
+	PREF_UNIT_RST_SET	= 1<<0,	/* Set   Prefetch Unit Reset */
+};
+
+/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
+/*	RB_START		32 bit	RAM Buffer Start Address */
+/*	RB_END			32 bit	RAM Buffer End Address */
+/*	RB_WP			32 bit	RAM Buffer Write Pointer */
+/*	RB_RP			32 bit	RAM Buffer Read Pointer */
+/*	RB_RX_UTPP		32 bit	Rx Upper Threshold, Pause Pack */
+/*	RB_RX_LTPP		32 bit	Rx Lower Threshold, Pause Pack */
+/*	RB_RX_UTHP		32 bit	Rx Upper Threshold, High Prio */
+/*	RB_RX_LTHP		32 bit	Rx Lower Threshold, High Prio */
+/*	RB_PC			32 bit	RAM Buffer Packet Counter */
+/*	RB_LEV			32 bit	RAM Buffer Level Register */
+
+#define RB_MSK	0x0007ffff	/* Bit 18.. 0:	RAM Buffer Pointer Bits */
+/*	RB_TST2			 8 bit	RAM Buffer Test Register 2 */
+/*	RB_TST1			 8 bit	RAM Buffer Test Register 1 */
+
+/*	RB_CTRL			 8 bit	RAM Buffer Control Register */
+enum {
+	RB_ENA_STFWD	= 1<<5,	/* Enable  Store & Forward */
+	RB_DIS_STFWD	= 1<<4,	/* Disable Store & Forward */
+	RB_ENA_OP_MD	= 1<<3,	/* Enable  Operation Mode */
+	RB_DIS_OP_MD	= 1<<2,	/* Disable Operation Mode */
+	RB_RST_CLR	= 1<<1,	/* Clear RAM Buf STM Reset */
+	RB_RST_SET	= 1<<0,	/* Set   RAM Buf STM Reset */
+};
+
+
+/* Transmit GMAC FIFO (YUKON only) */
+enum {
+	TX_GMF_EA	= 0x0d40,/* 32 bit	Tx GMAC FIFO End Address */
+	TX_GMF_AE_THR	= 0x0d44,/* 32 bit	Tx GMAC FIFO Almost Empty Thresh.*/
+	TX_GMF_CTRL_T	= 0x0d48,/* 32 bit	Tx GMAC FIFO Control/Test */
+
+	TX_GMF_WP	= 0x0d60,/* 32 bit 	Tx GMAC FIFO Write Pointer */
+	TX_GMF_WSP	= 0x0d64,/* 32 bit 	Tx GMAC FIFO Write Shadow Ptr. */
+	TX_GMF_WLEV	= 0x0d68,/* 32 bit 	Tx GMAC FIFO Write Level */
+
+	TX_GMF_RP	= 0x0d70,/* 32 bit 	Tx GMAC FIFO Read Pointer */
+	TX_GMF_RSTP	= 0x0d74,/* 32 bit 	Tx GMAC FIFO Restart Pointer */
+	TX_GMF_RLEV	= 0x0d78,/* 32 bit 	Tx GMAC FIFO Read Level */
+};
+
+/* Descriptor Poll Timer Registers */
+enum {
+	B28_DPT_INI	= 0x0e00,/* 24 bit	Descriptor Poll Timer Init Val */
+	B28_DPT_VAL	= 0x0e04,/* 24 bit	Descriptor Poll Timer Curr Val */
+	B28_DPT_CTRL	= 0x0e08,/*  8 bit	Descriptor Poll Timer Ctrl Reg */
+
+	B28_DPT_TST	= 0x0e0a,/*  8 bit	Descriptor Poll Timer Test Reg */
+};
+
+/* Time Stamp Timer Registers (YUKON only) */
+enum {
+	GMAC_TI_ST_VAL	= 0x0e14,/* 32 bit	Time Stamp Timer Curr Val */
+	GMAC_TI_ST_CTRL	= 0x0e18,/*  8 bit	Time Stamp Timer Ctrl Reg */
+	GMAC_TI_ST_TST	= 0x0e1a,/*  8 bit	Time Stamp Timer Test Reg */
+};
+
+/* Polling Unit Registers (Yukon-2 only) */
+enum {
+	POLL_CTRL	= 0x0e20, /* 32 bit	Polling Unit Control Reg */
+	POLL_LAST_IDX	= 0x0e24,/* 16 bit	Polling Unit List Last Index */
+
+	POLL_LIST_ADDR_LO= 0x0e28,/* 32 bit	Poll. List Start Addr (low) */
+	POLL_LIST_ADDR_HI= 0x0e2c,/* 32 bit	Poll. List Start Addr (high) */
+};
+
+/* ASF Subsystem Registers (Yukon-2 only) */
+enum {
+	B28_Y2_SMB_CONFIG  = 0x0e40,/* 32 bit	ASF SMBus Config Register */
+	B28_Y2_SMB_CSD_REG = 0x0e44,/* 32 bit	ASF SMB Control/Status/Data */
+	B28_Y2_ASF_IRQ_V_BASE=0x0e60,/* 32 bit	ASF IRQ Vector Base */
+
+	B28_Y2_ASF_STAT_CMD= 0x0e68,/* 32 bit	ASF Status and Command Reg */
+	B28_Y2_ASF_HOST_COM= 0x0e6c,/* 32 bit	ASF Host Communication Reg */
+	B28_Y2_DATA_REG_1  = 0x0e70,/* 32 bit	ASF/Host Data Register 1 */
+	B28_Y2_DATA_REG_2  = 0x0e74,/* 32 bit	ASF/Host Data Register 2 */
+	B28_Y2_DATA_REG_3  = 0x0e78,/* 32 bit	ASF/Host Data Register 3 */
+	B28_Y2_DATA_REG_4  = 0x0e7c,/* 32 bit	ASF/Host Data Register 4 */
+};
+
+/* Status BMU Registers (Yukon-2 only)*/
+enum {
+	STAT_CTRL	= 0x0e80,/* 32 bit	Status BMU Control Reg */
+	STAT_LAST_IDX	= 0x0e84,/* 16 bit	Status BMU Last Index */
+
+	STAT_LIST_ADDR_LO= 0x0e88,/* 32 bit	Status List Start Addr (low) */
+	STAT_LIST_ADDR_HI= 0x0e8c,/* 32 bit	Status List Start Addr (high) */
+	STAT_TXA1_RIDX	= 0x0e90,/* 16 bit	Status TxA1 Report Index Reg */
+	STAT_TXS1_RIDX	= 0x0e92,/* 16 bit	Status TxS1 Report Index Reg */
+	STAT_TXA2_RIDX	= 0x0e94,/* 16 bit	Status TxA2 Report Index Reg */
+	STAT_TXS2_RIDX	= 0x0e96,/* 16 bit	Status TxS2 Report Index Reg */
+	STAT_TX_IDX_TH	= 0x0e98,/* 16 bit	Status Tx Index Threshold Reg */
+	STAT_PUT_IDX	= 0x0e9c,/* 16 bit	Status Put Index Reg */
+
+/* FIFO Control/Status Registers (Yukon-2 only)*/
+	STAT_FIFO_WP	= 0x0ea0,/*  8 bit	Status FIFO Write Pointer Reg */
+	STAT_FIFO_RP	= 0x0ea4,/*  8 bit	Status FIFO Read Pointer Reg */
+	STAT_FIFO_RSP	= 0x0ea6,/*  8 bit	Status FIFO Read Shadow Ptr */
+	STAT_FIFO_LEVEL	= 0x0ea8,/*  8 bit	Status FIFO Level Reg */
+	STAT_FIFO_SHLVL	= 0x0eaa,/*  8 bit	Status FIFO Shadow Level Reg */
+	STAT_FIFO_WM	= 0x0eac,/*  8 bit	Status FIFO Watermark Reg */
+	STAT_FIFO_ISR_WM= 0x0ead,/*  8 bit	Status FIFO ISR Watermark Reg */
+
+/* Level and ISR Timer Registers (Yukon-2 only)*/
+	STAT_LEV_TIMER_INI= 0x0eb0,/* 32 bit	Level Timer Init. Value Reg */
+	STAT_LEV_TIMER_CNT= 0x0eb4,/* 32 bit	Level Timer Counter Reg */
+	STAT_LEV_TIMER_CTRL= 0x0eb8,/*  8 bit	Level Timer Control Reg */
+	STAT_LEV_TIMER_TEST= 0x0eb9,/*  8 bit	Level Timer Test Reg */
+	STAT_TX_TIMER_INI  = 0x0ec0,/* 32 bit	Tx Timer Init. Value Reg */
+	STAT_TX_TIMER_CNT  = 0x0ec4,/* 32 bit	Tx Timer Counter Reg */
+	STAT_TX_TIMER_CTRL = 0x0ec8,/*  8 bit	Tx Timer Control Reg */
+	STAT_TX_TIMER_TEST = 0x0ec9,/*  8 bit	Tx Timer Test Reg */
+	STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit	ISR Timer Init. Value Reg */
+	STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit	ISR Timer Counter Reg */
+	STAT_ISR_TIMER_CTRL= 0x0ed8,/*  8 bit	ISR Timer Control Reg */
+	STAT_ISR_TIMER_TEST= 0x0ed9,/*  8 bit	ISR Timer Test Reg */
+};
+
+enum {
+	LINKLED_OFF 	     = 0x01,
+	LINKLED_ON  	     = 0x02,
+	LINKLED_LINKSYNC_OFF = 0x04,
+	LINKLED_LINKSYNC_ON  = 0x08,
+	LINKLED_BLINK_OFF    = 0x10,
+	LINKLED_BLINK_ON     = 0x20,
+};
+
+/* GMAC and GPHY Control Registers (YUKON only) */
+enum {
+	GMAC_CTRL	= 0x0f00,/* 32 bit	GMAC Control Reg */
+	GPHY_CTRL	= 0x0f04,/* 32 bit	GPHY Control Reg */
+	GMAC_IRQ_SRC	= 0x0f08,/*  8 bit	GMAC Interrupt Source Reg */
+	GMAC_IRQ_MSK	= 0x0f0c,/*  8 bit	GMAC Interrupt Mask Reg */
+	GMAC_LINK_CTRL	= 0x0f10,/* 16 bit	Link Control Reg */
+
+/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
+
+	WOL_REG_OFFS	= 0x20,/* HW-Bug: Address is + 0x20 against spec. */
+
+	WOL_CTRL_STAT	= 0x0f20,/* 16 bit	WOL Control/Status Reg */
+	WOL_MATCH_CTL	= 0x0f22,/*  8 bit	WOL Match Control Reg */
+	WOL_MATCH_RES	= 0x0f23,/*  8 bit	WOL Match Result Reg */
+	WOL_MAC_ADDR	= 0x0f24,/* 32 bit	WOL MAC Address */
+	WOL_PATT_PME	= 0x0f2a,/*  8 bit	WOL PME Match Enable (Yukon-2) */
+	WOL_PATT_ASFM	= 0x0f2b,/*  8 bit	WOL ASF Match Enable (Yukon-2) */
+	WOL_PATT_RPTR	= 0x0f2c,/*  8 bit	WOL Pattern Read Pointer */
+
+/* WOL Pattern Length Registers (YUKON only) */
+
+	WOL_PATT_LEN_LO	= 0x0f30,/* 32 bit	WOL Pattern Length 3..0 */
+	WOL_PATT_LEN_HI	= 0x0f34,/* 24 bit	WOL Pattern Length 6..4 */
+
+/* WOL Pattern Counter Registers (YUKON only) */
+
+
+	WOL_PATT_CNT_0	= 0x0f38,/* 32 bit	WOL Pattern Counter 3..0 */
+	WOL_PATT_CNT_4	= 0x0f3c,/* 24 bit	WOL Pattern Counter 6..4 */
+};
+
+enum {
+	WOL_PATT_RAM_1	= 0x1000,/*  WOL Pattern RAM Link 1 */
+	WOL_PATT_RAM_2	= 0x1400,/*  WOL Pattern RAM Link 2 */
+};
+
+enum {
+	BASE_GMAC_1	= 0x2800,/* GMAC 1 registers */
+	BASE_GMAC_2	= 0x3800,/* GMAC 2 registers */
+};
+
+/*
+ * Marvel-PHY Registers, indirect addressed over GMAC
+ */
+enum {
+	PHY_MARV_CTRL		= 0x00,/* 16 bit r/w	PHY Control Register */
+	PHY_MARV_STAT		= 0x01,/* 16 bit r/o	PHY Status Register */
+	PHY_MARV_ID0		= 0x02,/* 16 bit r/o	PHY ID0 Register */
+	PHY_MARV_ID1		= 0x03,/* 16 bit r/o	PHY ID1 Register */
+	PHY_MARV_AUNE_ADV	= 0x04,/* 16 bit r/w	Auto-Neg. Advertisement */
+	PHY_MARV_AUNE_LP	= 0x05,/* 16 bit r/o	Link Part Ability Reg */
+	PHY_MARV_AUNE_EXP	= 0x06,/* 16 bit r/o	Auto-Neg. Expansion Reg */
+	PHY_MARV_NEPG		= 0x07,/* 16 bit r/w	Next Page Register */
+	PHY_MARV_NEPG_LP	= 0x08,/* 16 bit r/o	Next Page Link Partner */
+	/* Marvel-specific registers */
+	PHY_MARV_1000T_CTRL	= 0x09,/* 16 bit r/w	1000Base-T Control Reg */
+	PHY_MARV_1000T_STAT	= 0x0a,/* 16 bit r/o	1000Base-T Status Reg */
+	PHY_MARV_EXT_STAT	= 0x0f,/* 16 bit r/o	Extended Status Reg */
+	PHY_MARV_PHY_CTRL	= 0x10,/* 16 bit r/w	PHY Specific Ctrl Reg */
+	PHY_MARV_PHY_STAT	= 0x11,/* 16 bit r/o	PHY Specific Stat Reg */
+	PHY_MARV_INT_MASK	= 0x12,/* 16 bit r/w	Interrupt Mask Reg */
+	PHY_MARV_INT_STAT	= 0x13,/* 16 bit r/o	Interrupt Status Reg */
+	PHY_MARV_EXT_CTRL	= 0x14,/* 16 bit r/w	Ext. PHY Specific Ctrl */
+	PHY_MARV_RXE_CNT	= 0x15,/* 16 bit r/w	Receive Error Counter */
+	PHY_MARV_EXT_ADR	= 0x16,/* 16 bit r/w	Ext. Ad. for Cable Diag. */
+	PHY_MARV_PORT_IRQ	= 0x17,/* 16 bit r/o	Port 0 IRQ (88E1111 only) */
+	PHY_MARV_LED_CTRL	= 0x18,/* 16 bit r/w	LED Control Reg */
+	PHY_MARV_LED_OVER	= 0x19,/* 16 bit r/w	Manual LED Override Reg */
+	PHY_MARV_EXT_CTRL_2	= 0x1a,/* 16 bit r/w	Ext. PHY Specific Ctrl 2 */
+	PHY_MARV_EXT_P_STAT	= 0x1b,/* 16 bit r/w	Ext. PHY Spec. Stat Reg */
+	PHY_MARV_CABLE_DIAG	= 0x1c,/* 16 bit r/o	Cable Diagnostic Reg */
+	PHY_MARV_PAGE_ADDR	= 0x1d,/* 16 bit r/w	Extended Page Address Reg */
+	PHY_MARV_PAGE_DATA	= 0x1e,/* 16 bit r/w	Extended Page Data Reg */
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+	PHY_MARV_FE_LED_PAR	= 0x16,/* 16 bit r/w	LED Parallel Select Reg. */
+	PHY_MARV_FE_LED_SER	= 0x17,/* 16 bit r/w	LED Stream Select S. LED */
+	PHY_MARV_FE_VCT_TX	= 0x1a,/* 16 bit r/w	VCT Reg. for TXP/N Pins */
+	PHY_MARV_FE_VCT_RX	= 0x1b,/* 16 bit r/o	VCT Reg. for RXP/N Pins */
+	PHY_MARV_FE_SPEC_2	= 0x1c,/* 16 bit r/w	Specific Control Reg. 2 */
+};
+
+enum {
+	PHY_CT_RESET	= 1<<15, /* Bit 15: (sc)	clear all PHY related regs */
+	PHY_CT_LOOP	= 1<<14, /* Bit 14:	enable Loopback over PHY */
+	PHY_CT_SPS_LSB	= 1<<13, /* Bit 13:	Speed select, lower bit */
+	PHY_CT_ANE	= 1<<12, /* Bit 12:	Auto-Negotiation Enabled */
+	PHY_CT_PDOWN	= 1<<11, /* Bit 11:	Power Down Mode */
+	PHY_CT_ISOL	= 1<<10, /* Bit 10:	Isolate Mode */
+	PHY_CT_RE_CFG	= 1<<9, /* Bit  9:	(sc) Restart Auto-Negotiation */
+	PHY_CT_DUP_MD	= 1<<8, /* Bit  8:	Duplex Mode */
+	PHY_CT_COL_TST	= 1<<7, /* Bit  7:	Collision Test enabled */
+	PHY_CT_SPS_MSB	= 1<<6, /* Bit  6:	Speed select, upper bit */
+};
+
+enum {
+	PHY_CT_SP1000	= PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
+	PHY_CT_SP100	= PHY_CT_SPS_LSB, /* enable speed of  100 Mbps */
+	PHY_CT_SP10	= 0,		  /* enable speed of   10 Mbps */
+};
+
+enum {
+	PHY_ST_EXT_ST	= 1<<8, /* Bit  8:	Extended Status Present */
+
+	PHY_ST_PRE_SUP	= 1<<6, /* Bit  6:	Preamble Suppression */
+	PHY_ST_AN_OVER	= 1<<5, /* Bit  5:	Auto-Negotiation Over */
+	PHY_ST_REM_FLT	= 1<<4, /* Bit  4:	Remote Fault Condition Occured */
+	PHY_ST_AN_CAP	= 1<<3, /* Bit  3:	Auto-Negotiation Capability */
+	PHY_ST_LSYNC	= 1<<2, /* Bit  2:	Link Synchronized */
+	PHY_ST_JAB_DET	= 1<<1, /* Bit  1:	Jabber Detected */
+	PHY_ST_EXT_REG	= 1<<0, /* Bit  0:	Extended Register available */
+};
+
+enum {
+	PHY_I1_OUI_MSK	= 0x3f<<10, /* Bit 15..10:	Organization Unique ID */
+	PHY_I1_MOD_NUM	= 0x3f<<4, /* Bit  9.. 4:	Model Number */
+	PHY_I1_REV_MSK	= 0xf, /* Bit  3.. 0:	Revision Number */
+};
+
+/* different Marvell PHY Ids */
+enum {
+	PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
+
+	PHY_BCOM_ID1_A1	= 0x6041,
+	PHY_BCOM_ID1_B2	= 0x6043,
+	PHY_BCOM_ID1_C0	= 0x6044,
+	PHY_BCOM_ID1_C5	= 0x6047,
+
+	PHY_MARV_ID1_B0	= 0x0C23, /* Yukon (PHY 88E1011) */
+	PHY_MARV_ID1_B2	= 0x0C25, /* Yukon-Plus (PHY 88E1011) */
+	PHY_MARV_ID1_C2	= 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+	PHY_MARV_ID1_Y2	= 0x0C91, /* Yukon-2 (PHY 88E1112) */
+};
+
+/* Advertisement register bits */
+enum {
+	PHY_AN_NXT_PG	= 1<<15, /* Bit 15:	Request Next Page */
+	PHY_AN_ACK	= 1<<14, /* Bit 14:	(ro) Acknowledge Received */
+	PHY_AN_RF	= 1<<13, /* Bit 13:	Remote Fault Bits */
+
+	PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11:	Try for asymmetric */
+	PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10:	Try for pause */
+	PHY_AN_100BASE4	= 1<<9, /* Bit 9:	Try for 100mbps 4k packets */
+	PHY_AN_100FULL	= 1<<8, /* Bit 8:	Try for 100mbps full-duplex */
+	PHY_AN_100HALF	= 1<<7, /* Bit 7:	Try for 100mbps half-duplex */
+	PHY_AN_10FULL	= 1<<6, /* Bit 6:	Try for 10mbps full-duplex */
+	PHY_AN_10HALF	= 1<<5, /* Bit 5:	Try for 10mbps half-duplex */
+	PHY_AN_CSMA	= 1<<0, /* Bit 0:	Only selector supported */
+	PHY_AN_SEL	= 0x1f, /* Bit 4..0:	Selector Field, 00001=Ethernet*/
+	PHY_AN_FULL	= PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
+	PHY_AN_ALL	= PHY_AN_10HALF | PHY_AN_10FULL |
+		  	  PHY_AN_100HALF | PHY_AN_100FULL,
+};
+
+/*****  PHY_BCOM_1000T_STAT	16 bit r/o	1000Base-T Status Reg *****/
+/*****  PHY_MARV_1000T_STAT	16 bit r/o	1000Base-T Status Reg *****/
+enum {
+	PHY_B_1000S_MSF	= 1<<15, /* Bit 15:	Master/Slave Fault */
+	PHY_B_1000S_MSR	= 1<<14, /* Bit 14:	Master/Slave Result */
+	PHY_B_1000S_LRS	= 1<<13, /* Bit 13:	Local Receiver Status */
+	PHY_B_1000S_RRS	= 1<<12, /* Bit 12:	Remote Receiver Status */
+	PHY_B_1000S_LP_FD	= 1<<11, /* Bit 11:	Link Partner can FD */
+	PHY_B_1000S_LP_HD	= 1<<10, /* Bit 10:	Link Partner can HD */
+									/* Bit  9..8:	reserved */
+	PHY_B_1000S_IEC	= 0xff, /* Bit  7..0:	Idle Error Count */
+};
+
+/** Marvell-Specific */
+enum {
+	PHY_M_AN_NXT_PG	= 1<<15, /* Request Next Page */
+	PHY_M_AN_ACK	= 1<<14, /* (ro)	Acknowledge Received */
+	PHY_M_AN_RF	= 1<<13, /* Remote Fault */
+
+	PHY_M_AN_ASP	= 1<<11, /* Asymmetric Pause */
+	PHY_M_AN_PC	= 1<<10, /* MAC Pause implemented */
+	PHY_M_AN_100_T4	= 1<<9, /* Not cap. 100Base-T4 (always 0) */
+	PHY_M_AN_100_FD	= 1<<8, /* Advertise 100Base-TX Full Duplex */
+	PHY_M_AN_100_HD	= 1<<7, /* Advertise 100Base-TX Half Duplex */
+	PHY_M_AN_10_FD	= 1<<6, /* Advertise 10Base-TX Full Duplex */
+	PHY_M_AN_10_HD	= 1<<5, /* Advertise 10Base-TX Half Duplex */
+	PHY_M_AN_SEL_MSK =0x1f<<4,	/* Bit  4.. 0: Selector Field Mask */
+};
+
+/* special defines for FIBER (88E1011S only) */
+enum {
+	PHY_M_AN_ASP_X	= 1<<8, /* Asymmetric Pause */
+	PHY_M_AN_PC_X	= 1<<7, /* MAC Pause implemented */
+	PHY_M_AN_1000X_AHD	= 1<<6, /* Advertise 10000Base-X Half Duplex */
+	PHY_M_AN_1000X_AFD	= 1<<5, /* Advertise 10000Base-X Full Duplex */
+};
+
+/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
+enum {
+	PHY_M_P_NO_PAUSE_X	= 0<<7,/* Bit  8.. 7:	no Pause Mode */
+	PHY_M_P_SYM_MD_X	= 1<<7, /* Bit  8.. 7:	symmetric Pause Mode */
+	PHY_M_P_ASYM_MD_X	= 2<<7,/* Bit  8.. 7:	asymmetric Pause Mode */
+	PHY_M_P_BOTH_MD_X	= 3<<7,/* Bit  8.. 7:	both Pause Mode */
+};
+
+/*****  PHY_MARV_1000T_CTRL	16 bit r/w	1000Base-T Control Reg *****/
+enum {
+	PHY_M_1000C_TEST	= 7<<13,/* Bit 15..13:	Test Modes */
+	PHY_M_1000C_MSE	= 1<<12, /* Manual Master/Slave Enable */
+	PHY_M_1000C_MSC	= 1<<11, /* M/S Configuration (1=Master) */
+	PHY_M_1000C_MPD	= 1<<10, /* Multi-Port Device */
+	PHY_M_1000C_AFD	= 1<<9, /* Advertise Full Duplex */
+	PHY_M_1000C_AHD	= 1<<8, /* Advertise Half Duplex */
+};
+
+/*****  PHY_MARV_PHY_CTRL	16 bit r/w	PHY Specific Ctrl Reg *****/
+enum {
+	PHY_M_PC_TX_FFD_MSK	= 3<<14,/* Bit 15..14: Tx FIFO Depth Mask */
+	PHY_M_PC_RX_FFD_MSK	= 3<<12,/* Bit 13..12: Rx FIFO Depth Mask */
+	PHY_M_PC_ASS_CRS_TX	= 1<<11, /* Assert CRS on Transmit */
+	PHY_M_PC_FL_GOOD	= 1<<10, /* Force Link Good */
+	PHY_M_PC_EN_DET_MSK	= 3<<8,/* Bit  9.. 8: Energy Detect Mask */
+	PHY_M_PC_ENA_EXT_D	= 1<<7, /* Enable Ext. Distance (10BT) */
+	PHY_M_PC_MDIX_MSK	= 3<<5,/* Bit  6.. 5: MDI/MDIX Config. Mask */
+	PHY_M_PC_DIS_125CLK	= 1<<4, /* Disable 125 CLK */
+	PHY_M_PC_MAC_POW_UP	= 1<<3, /* MAC Power up */
+	PHY_M_PC_SQE_T_ENA	= 1<<2, /* SQE Test Enabled */
+	PHY_M_PC_POL_R_DIS	= 1<<1, /* Polarity Reversal Disabled */
+	PHY_M_PC_DIS_JABBER	= 1<<0, /* Disable Jabber */
+};
+
+enum {
+	PHY_M_PC_EN_DET		= 2<<8,	/* Energy Detect (Mode 1) */
+	PHY_M_PC_EN_DET_PLUS	= 3<<8, /* Energy Detect Plus (Mode 2) */
+};
+
+#define PHY_M_PC_MDI_XMODE(x)	(((x)<<5) & PHY_M_PC_MDIX_MSK)
+
+enum {
+	PHY_M_PC_MAN_MDI	= 0, /* 00 = Manual MDI configuration */
+	PHY_M_PC_MAN_MDIX	= 1, /* 01 = Manual MDIX configuration */
+	PHY_M_PC_ENA_AUTO	= 3, /* 11 = Enable Automatic Crossover */
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+	PHY_M_PC_ENA_DTE_DT	= 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
+	PHY_M_PC_ENA_ENE_DT	= 1<<14, /* Enable Energy Detect (sense & pulse) */
+	PHY_M_PC_DIS_NLP_CK	= 1<<13, /* Disable Normal Link Puls (NLP) Check */
+	PHY_M_PC_ENA_LIP_NP	= 1<<12, /* Enable Link Partner Next Page Reg. */
+	PHY_M_PC_DIS_NLP_GN	= 1<<11, /* Disable Normal Link Puls Generation */
+
+	PHY_M_PC_DIS_SCRAMB	= 1<<9, /* Disable Scrambler */
+	PHY_M_PC_DIS_FEFI	= 1<<8, /* Disable Far End Fault Indic. (FEFI) */
+
+	PHY_M_PC_SH_TP_SEL	= 1<<6, /* Shielded Twisted Pair Select */
+	PHY_M_PC_RX_FD_MSK	= 3<<2,/* Bit  3.. 2: Rx FIFO Depth Mask */
+};
+
+/*****  PHY_MARV_PHY_STAT	16 bit r/o	PHY Specific Status Reg *****/
+enum {
+	PHY_M_PS_SPEED_MSK	= 3<<14, /* Bit 15..14: Speed Mask */
+	PHY_M_PS_SPEED_1000	= 1<<15, /*		10 = 1000 Mbps */
+	PHY_M_PS_SPEED_100	= 1<<14, /*		01 =  100 Mbps */
+	PHY_M_PS_SPEED_10	= 0,	 /*		00 =   10 Mbps */
+	PHY_M_PS_FULL_DUP	= 1<<13, /* Full Duplex */
+	PHY_M_PS_PAGE_REC	= 1<<12, /* Page Received */
+	PHY_M_PS_SPDUP_RES	= 1<<11, /* Speed & Duplex Resolved */
+	PHY_M_PS_LINK_UP	= 1<<10, /* Link Up */
+	PHY_M_PS_CABLE_MSK	= 7<<7,  /* Bit  9.. 7: Cable Length Mask */
+	PHY_M_PS_MDI_X_STAT	= 1<<6,  /* MDI Crossover Stat (1=MDIX) */
+	PHY_M_PS_DOWNS_STAT	= 1<<5,  /* Downshift Status (1=downsh.) */
+	PHY_M_PS_ENDET_STAT	= 1<<4,  /* Energy Detect Status (1=act) */
+	PHY_M_PS_TX_P_EN	= 1<<3,  /* Tx Pause Enabled */
+	PHY_M_PS_RX_P_EN	= 1<<2,  /* Rx Pause Enabled */
+	PHY_M_PS_POL_REV	= 1<<1,  /* Polarity Reversed */
+	PHY_M_PS_JABBER		= 1<<0,  /* Jabber */
+};
+
+#define PHY_M_PS_PAUSE_MSK	(PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+enum {
+	PHY_M_PS_DTE_DETECT	= 1<<15, /* Data Terminal Equipment (DTE) Detected */
+	PHY_M_PS_RES_SPEED	= 1<<14, /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
+};
+
+enum {
+	PHY_M_IS_AN_ERROR	= 1<<15, /* Auto-Negotiation Error */
+	PHY_M_IS_LSP_CHANGE	= 1<<14, /* Link Speed Changed */
+	PHY_M_IS_DUP_CHANGE	= 1<<13, /* Duplex Mode Changed */
+	PHY_M_IS_AN_PR		= 1<<12, /* Page Received */
+	PHY_M_IS_AN_COMPL	= 1<<11, /* Auto-Negotiation Completed */
+	PHY_M_IS_LST_CHANGE	= 1<<10, /* Link Status Changed */
+	PHY_M_IS_SYMB_ERROR	= 1<<9, /* Symbol Error */
+	PHY_M_IS_FALSE_CARR	= 1<<8, /* False Carrier */
+	PHY_M_IS_FIFO_ERROR	= 1<<7, /* FIFO Overflow/Underrun Error */
+	PHY_M_IS_MDI_CHANGE	= 1<<6, /* MDI Crossover Changed */
+	PHY_M_IS_DOWNSH_DET	= 1<<5, /* Downshift Detected */
+	PHY_M_IS_END_CHANGE	= 1<<4, /* Energy Detect Changed */
+
+	PHY_M_IS_DTE_CHANGE	= 1<<2, /* DTE Power Det. Status Changed */
+	PHY_M_IS_POL_CHANGE	= 1<<1, /* Polarity Changed */
+	PHY_M_IS_JABBER		= 1<<0, /* Jabber */
+
+	PHY_M_DEF_MSK		= PHY_M_IS_LSP_CHANGE | PHY_M_IS_LST_CHANGE
+				 | PHY_M_IS_FIFO_ERROR,
+	PHY_M_AN_MSK	       = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
+};
+
+
+/*****  PHY_MARV_EXT_CTRL	16 bit r/w	Ext. PHY Specific Ctrl *****/
+enum {
+	PHY_M_EC_ENA_BC_EXT = 1<<15, /* Enable Block Carr. Ext. (88E1111 only) */
+	PHY_M_EC_ENA_LIN_LB = 1<<14, /* Enable Line Loopback (88E1111 only) */
+
+	PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
+	PHY_M_EC_M_DSC_MSK  = 3<<10, /* Bit 11..10:	Master Downshift Counter */
+					/* (88E1011 only) */
+	PHY_M_EC_S_DSC_MSK  = 3<<8,/* Bit  9.. 8:	Slave  Downshift Counter */
+				       /* (88E1011 only) */
+	PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9:	Master Downshift Counter */
+					/* (88E1111 only) */
+	PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
+					/* !!! Errata in spec. (1 = disable) */
+	PHY_M_EC_RX_TIM_CT  = 1<<7, /* RGMII Rx Timing Control*/
+	PHY_M_EC_MAC_S_MSK  = 7<<4,/* Bit  6.. 4:	Def. MAC interface speed */
+	PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
+	PHY_M_EC_DTE_D_ENA  = 1<<2, /* DTE Detect Enable (88E1111 only) */
+	PHY_M_EC_TX_TIM_CT  = 1<<1, /* RGMII Tx Timing Control */
+	PHY_M_EC_TRANS_DIS  = 1<<0, /* Transmitter Disable (88E1111 only) */};
+
+#define PHY_M_EC_M_DSC(x)	((x)<<10 & PHY_M_EC_M_DSC_MSK)
+					/* 00=1x; 01=2x; 10=3x; 11=4x */
+#define PHY_M_EC_S_DSC(x)	((x)<<8 & PHY_M_EC_S_DSC_MSK)
+					/* 00=dis; 01=1x; 10=2x; 11=3x */
+#define PHY_M_EC_DSC_2(x)	((x)<<9 & PHY_M_EC_M_DSC_MSK2)
+					/* 000=1x; 001=2x; 010=3x; 011=4x */
+#define PHY_M_EC_MAC_S(x)	((x)<<4 & PHY_M_EC_MAC_S_MSK)
+					/* 01X=0; 110=2.5; 111=25 (MHz) */
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+enum {
+	PHY_M_PC_DIS_LINK_Pa	= 1<<15,/* Disable Link Pulses */
+	PHY_M_PC_DSC_MSK	= 7<<12,/* Bit 14..12:	Downshift Counter */
+	PHY_M_PC_DOWN_S_ENA	= 1<<11,/* Downshift Enable */
+};
+/* !!! Errata in spec. (1 = disable) */
+
+#define PHY_M_PC_DSC(x)			(((x)<<12) & PHY_M_PC_DSC_MSK)
+											/* 100=5x; 101=6x; 110=7x; 111=8x */
+enum {
+	MAC_TX_CLK_0_MHZ	= 2,
+	MAC_TX_CLK_2_5_MHZ	= 6,
+	MAC_TX_CLK_25_MHZ 	= 7,
+};
+
+/*****  PHY_MARV_LED_CTRL	16 bit r/w	LED Control Reg *****/
+enum {
+	PHY_M_LEDC_DIS_LED	= 1<<15, /* Disable LED */
+	PHY_M_LEDC_PULS_MSK	= 7<<12,/* Bit 14..12: Pulse Stretch Mask */
+	PHY_M_LEDC_F_INT	= 1<<11, /* Force Interrupt */
+	PHY_M_LEDC_BL_R_MSK	= 7<<8,/* Bit 10.. 8: Blink Rate Mask */
+	PHY_M_LEDC_DP_C_LSB	= 1<<7, /* Duplex Control (LSB, 88E1111 only) */
+	PHY_M_LEDC_TX_C_LSB	= 1<<6, /* Tx Control (LSB, 88E1111 only) */
+	PHY_M_LEDC_LK_C_MSK	= 7<<3,/* Bit  5.. 3: Link Control Mask */
+					/* (88E1111 only) */
+};
+
+enum {
+	PHY_M_LEDC_LINK_MSK	= 3<<3,/* Bit  4.. 3: Link Control Mask */
+									/* (88E1011 only) */
+	PHY_M_LEDC_DP_CTRL	= 1<<2, /* Duplex Control */
+	PHY_M_LEDC_DP_C_MSB	= 1<<2, /* Duplex Control (MSB, 88E1111 only) */
+	PHY_M_LEDC_RX_CTRL	= 1<<1, /* Rx Activity / Link */
+	PHY_M_LEDC_TX_CTRL	= 1<<0, /* Tx Activity / Link */
+	PHY_M_LEDC_TX_C_MSB	= 1<<0, /* Tx Control (MSB, 88E1111 only) */
+};
+
+#define PHY_M_LED_PULS_DUR(x)	(((x)<<12) & PHY_M_LEDC_PULS_MSK)
+
+/*****  PHY_MARV_PHY_STAT (page 3)16 bit r/w	Polarity Control Reg. *****/
+enum {
+	PHY_M_POLC_LS1M_MSK	= 0xf<<12, /* Bit 15..12: LOS,STAT1 Mix % Mask */
+	PHY_M_POLC_IS0M_MSK	= 0xf<<8,  /* Bit 11.. 8: INIT,STAT0 Mix % Mask */
+	PHY_M_POLC_LOS_MSK	= 0x3<<6,  /* Bit  7.. 6: LOS Pol. Ctrl. Mask */
+	PHY_M_POLC_INIT_MSK	= 0x3<<4,  /* Bit  5.. 4: INIT Pol. Ctrl. Mask */
+	PHY_M_POLC_STA1_MSK	= 0x3<<2,  /* Bit  3.. 2: STAT1 Pol. Ctrl. Mask */
+	PHY_M_POLC_STA0_MSK	= 0x3,     /* Bit  1.. 0: STAT0 Pol. Ctrl. Mask */
+};
+
+#define PHY_M_POLC_LS1_P_MIX(x)	(((x)<<12) & PHY_M_POLC_LS1M_MSK)
+#define PHY_M_POLC_IS0_P_MIX(x)	(((x)<<8) & PHY_M_POLC_IS0M_MSK)
+#define PHY_M_POLC_LOS_CTRL(x)	(((x)<<6) & PHY_M_POLC_LOS_MSK)
+#define PHY_M_POLC_INIT_CTRL(x)	(((x)<<4) & PHY_M_POLC_INIT_MSK)
+#define PHY_M_POLC_STA1_CTRL(x)	(((x)<<2) & PHY_M_POLC_STA1_MSK)
+#define PHY_M_POLC_STA0_CTRL(x)	(((x)<<0) & PHY_M_POLC_STA0_MSK)
+
+enum {
+	PULS_NO_STR	= 0,/* no pulse stretching */
+	PULS_21MS	= 1,/* 21 ms to 42 ms */
+	PULS_42MS	= 2,/* 42 ms to 84 ms */
+	PULS_84MS	= 3,/* 84 ms to 170 ms */
+	PULS_170MS	= 4,/* 170 ms to 340 ms */
+	PULS_340MS	= 5,/* 340 ms to 670 ms */
+	PULS_670MS	= 6,/* 670 ms to 1.3 s */
+	PULS_1300MS	= 7,/* 1.3 s to 2.7 s */
+};
+
+#define PHY_M_LED_BLINK_RT(x)	(((x)<<8) & PHY_M_LEDC_BL_R_MSK)
+
+enum {
+	BLINK_42MS	= 0,/* 42 ms */
+	BLINK_84MS	= 1,/* 84 ms */
+	BLINK_170MS	= 2,/* 170 ms */
+	BLINK_340MS	= 3,/* 340 ms */
+	BLINK_670MS	= 4,/* 670 ms */
+};
+
+/*****  PHY_MARV_LED_OVER	16 bit r/w	Manual LED Override Reg *****/
+#define PHY_M_LED_MO_SGMII(x)	((x)<<14) /* Bit 15..14:  SGMII AN Timer */
+										/* Bit 13..12:	reserved */
+#define PHY_M_LED_MO_DUP(x)	((x)<<10) /* Bit 11..10:  Duplex */
+#define PHY_M_LED_MO_10(x)	((x)<<8) /* Bit  9.. 8:  Link 10 */
+#define PHY_M_LED_MO_100(x)	((x)<<6) /* Bit  7.. 6:  Link 100 */
+#define PHY_M_LED_MO_1000(x)	((x)<<4) /* Bit  5.. 4:  Link 1000 */
+#define PHY_M_LED_MO_RX(x)	((x)<<2) /* Bit  3.. 2:  Rx */
+#define PHY_M_LED_MO_TX(x)	((x)<<0) /* Bit  1.. 0:  Tx */
+
+enum {
+	MO_LED_NORM	= 0,
+	MO_LED_BLINK	= 1,
+	MO_LED_OFF	= 2,
+	MO_LED_ON	= 3,
+};
+
+/*****  PHY_MARV_EXT_CTRL_2	16 bit r/w	Ext. PHY Specific Ctrl 2 *****/
+enum {
+	PHY_M_EC2_FI_IMPED	= 1<<6, /* Fiber Input  Impedance */
+	PHY_M_EC2_FO_IMPED	= 1<<5, /* Fiber Output Impedance */
+	PHY_M_EC2_FO_M_CLK	= 1<<4, /* Fiber Mode Clock Enable */
+	PHY_M_EC2_FO_BOOST	= 1<<3, /* Fiber Output Boost */
+	PHY_M_EC2_FO_AM_MSK	= 7,/* Bit  2.. 0:	Fiber Output Amplitude */
+};
+
+/*****  PHY_MARV_EXT_P_STAT 16 bit r/w	Ext. PHY Specific Status *****/
+enum {
+	PHY_M_FC_AUTO_SEL	= 1<<15, /* Fiber/Copper Auto Sel. Dis. */
+	PHY_M_FC_AN_REG_ACC	= 1<<14, /* Fiber/Copper AN Reg. Access */
+	PHY_M_FC_RESOLUTION	= 1<<13, /* Fiber/Copper Resolution */
+	PHY_M_SER_IF_AN_BP	= 1<<12, /* Ser. IF AN Bypass Enable */
+	PHY_M_SER_IF_BP_ST	= 1<<11, /* Ser. IF AN Bypass Status */
+	PHY_M_IRQ_POLARITY	= 1<<10, /* IRQ polarity */
+	PHY_M_DIS_AUT_MED	= 1<<9, /* Disable Aut. Medium Reg. Selection */
+	/* (88E1111 only) */
+
+	PHY_M_UNDOC1		= 1<<7, /* undocumented bit !! */
+	PHY_M_DTE_POW_STAT	= 1<<4, /* DTE Power Status (88E1111 only) */
+	PHY_M_MODE_MASK	= 0xf, /* Bit  3.. 0: copy of HWCFG MODE[3:0] */
+};
+
+/* for 10/100 Fast Ethernet PHY (88E3082 only) */
+/*****  PHY_MARV_FE_LED_PAR		16 bit r/w	LED Parallel Select Reg. *****/
+									/* Bit 15..12: reserved (used internally) */
+enum {
+	PHY_M_FELP_LED2_MSK = 0xf<<8,	/* Bit 11.. 8: LED2 Mask (LINK) */
+	PHY_M_FELP_LED1_MSK = 0xf<<4,	/* Bit  7.. 4: LED1 Mask (ACT) */
+	PHY_M_FELP_LED0_MSK = 0xf, /* Bit  3.. 0: LED0 Mask (SPEED) */
+};
+
+#define PHY_M_FELP_LED2_CTRL(x)	(((x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x)	(((x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x)	(((x)<<0) & PHY_M_FELP_LED0_MSK)
+
+enum {
+	LED_PAR_CTRL_COLX	= 0x00,
+	LED_PAR_CTRL_ERROR	= 0x01,
+	LED_PAR_CTRL_DUPLEX	= 0x02,
+	LED_PAR_CTRL_DP_COL	= 0x03,
+	LED_PAR_CTRL_SPEED	= 0x04,
+	LED_PAR_CTRL_LINK	= 0x05,
+	LED_PAR_CTRL_TX		= 0x06,
+	LED_PAR_CTRL_RX		= 0x07,
+	LED_PAR_CTRL_ACT	= 0x08,
+	LED_PAR_CTRL_LNK_RX	= 0x09,
+	LED_PAR_CTRL_LNK_AC	= 0x0a,
+	LED_PAR_CTRL_ACT_BL	= 0x0b,
+	LED_PAR_CTRL_TX_BL	= 0x0c,
+	LED_PAR_CTRL_RX_BL	= 0x0d,
+	LED_PAR_CTRL_COL_BL	= 0x0e,
+	LED_PAR_CTRL_INACT	= 0x0f
+};
+
+/*****,PHY_MARV_FE_SPEC_2		16 bit r/w	Specific Control Reg. 2 *****/
+enum {
+	PHY_M_FESC_DIS_WAIT	= 1<<2, /* Disable TDR Waiting Period */
+	PHY_M_FESC_ENA_MCLK	= 1<<1, /* Enable MAC Rx Clock in sleep mode */
+	PHY_M_FESC_SEL_CL_A	= 1<<0, /* Select Class A driver (100B-TX) */
+};
+
+/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
+/*****  PHY_MARV_PHY_CTRL (page 2)		16 bit r/w	MAC Specific Ctrl *****/
+enum {
+	PHY_M_MAC_MD_MSK	= 7<<7, /* Bit  9.. 7: Mode Select Mask */
+	PHY_M_MAC_MD_AUTO	= 3,/* Auto Copper/1000Base-X */
+	PHY_M_MAC_MD_COPPER	= 5,/* Copper only */
+	PHY_M_MAC_MD_1000BX	= 7,/* 1000Base-X only */
+};
+#define PHY_M_MAC_MODE_SEL(x)	(((x)<<7) & PHY_M_MAC_MD_MSK)
+
+/*****  PHY_MARV_PHY_CTRL (page 3)		16 bit r/w	LED Control Reg. *****/
+enum {
+	PHY_M_LEDC_LOS_MSK	= 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
+	PHY_M_LEDC_INIT_MSK	= 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
+	PHY_M_LEDC_STA1_MSK	= 0xf<<4,/* Bit  7.. 4: STAT1 LED Ctrl. Mask */
+	PHY_M_LEDC_STA0_MSK	= 0xf, /* Bit  3.. 0: STAT0 LED Ctrl. Mask */
+};
+
+#define PHY_M_LEDC_LOS_CTRL(x)	(((x)<<12) & PHY_M_LEDC_LOS_MSK)
+#define PHY_M_LEDC_INIT_CTRL(x)	(((x)<<8) & PHY_M_LEDC_INIT_MSK)
+#define PHY_M_LEDC_STA1_CTRL(x)	(((x)<<4) & PHY_M_LEDC_STA1_MSK)
+#define PHY_M_LEDC_STA0_CTRL(x)	(((x)<<0) & PHY_M_LEDC_STA0_MSK)
+
+/* GMAC registers  */
+/* Port Registers */
+enum {
+	GM_GP_STAT	= 0x0000,	/* 16 bit r/o	General Purpose Status */
+	GM_GP_CTRL	= 0x0004,	/* 16 bit r/w	General Purpose Control */
+	GM_TX_CTRL	= 0x0008,	/* 16 bit r/w	Transmit Control Reg. */
+	GM_RX_CTRL	= 0x000c,	/* 16 bit r/w	Receive Control Reg. */
+	GM_TX_FLOW_CTRL	= 0x0010,	/* 16 bit r/w	Transmit Flow-Control */
+	GM_TX_PARAM	= 0x0014,	/* 16 bit r/w	Transmit Parameter Reg. */
+	GM_SERIAL_MODE	= 0x0018,	/* 16 bit r/w	Serial Mode Register */
+/* Source Address Registers */
+	GM_SRC_ADDR_1L	= 0x001c,	/* 16 bit r/w	Source Address 1 (low) */
+	GM_SRC_ADDR_1M	= 0x0020,	/* 16 bit r/w	Source Address 1 (middle) */
+	GM_SRC_ADDR_1H	= 0x0024,	/* 16 bit r/w	Source Address 1 (high) */
+	GM_SRC_ADDR_2L	= 0x0028,	/* 16 bit r/w	Source Address 2 (low) */
+	GM_SRC_ADDR_2M	= 0x002c,	/* 16 bit r/w	Source Address 2 (middle) */
+	GM_SRC_ADDR_2H	= 0x0030,	/* 16 bit r/w	Source Address 2 (high) */
+
+/* Multicast Address Hash Registers */
+	GM_MC_ADDR_H1	= 0x0034,	/* 16 bit r/w	Multicast Address Hash 1 */
+	GM_MC_ADDR_H2	= 0x0038,	/* 16 bit r/w	Multicast Address Hash 2 */
+	GM_MC_ADDR_H3	= 0x003c,	/* 16 bit r/w	Multicast Address Hash 3 */
+	GM_MC_ADDR_H4	= 0x0040,	/* 16 bit r/w	Multicast Address Hash 4 */
+
+/* Interrupt Source Registers */
+	GM_TX_IRQ_SRC	= 0x0044,	/* 16 bit r/o	Tx Overflow IRQ Source */
+	GM_RX_IRQ_SRC	= 0x0048,	/* 16 bit r/o	Rx Overflow IRQ Source */
+	GM_TR_IRQ_SRC	= 0x004c,	/* 16 bit r/o	Tx/Rx Over. IRQ Source */
+
+/* Interrupt Mask Registers */
+	GM_TX_IRQ_MSK	= 0x0050,	/* 16 bit r/w	Tx Overflow IRQ Mask */
+	GM_RX_IRQ_MSK	= 0x0054,	/* 16 bit r/w	Rx Overflow IRQ Mask */
+	GM_TR_IRQ_MSK	= 0x0058,	/* 16 bit r/w	Tx/Rx Over. IRQ Mask */
+
+/* Serial Management Interface (SMI) Registers */
+	GM_SMI_CTRL	= 0x0080,	/* 16 bit r/w	SMI Control Register */
+	GM_SMI_DATA	= 0x0084,	/* 16 bit r/w	SMI Data Register */
+	GM_PHY_ADDR	= 0x0088,	/* 16 bit r/w	GPHY Address Register */
+};
+
+/* MIB Counters */
+#define GM_MIB_CNT_BASE	0x0100		/* Base Address of MIB Counters */
+#define GM_MIB_CNT_SIZE	44		/* Number of MIB Counters */
+
+/*
+ * MIB Counters base address definitions (low word) -
+ * use offset 4 for access to high word	(32 bit r/o)
+ */
+enum {
+	GM_RXF_UC_OK  = GM_MIB_CNT_BASE + 0,	/* Unicast Frames Received OK */
+	GM_RXF_BC_OK	= GM_MIB_CNT_BASE + 8,	/* Broadcast Frames Received OK */
+	GM_RXF_MPAUSE	= GM_MIB_CNT_BASE + 16,	/* Pause MAC Ctrl Frames Received */
+	GM_RXF_MC_OK	= GM_MIB_CNT_BASE + 24,	/* Multicast Frames Received OK */
+	GM_RXF_FCS_ERR	= GM_MIB_CNT_BASE + 32,	/* Rx Frame Check Seq. Error */
+	/* GM_MIB_CNT_BASE + 40:	reserved */
+	GM_RXO_OK_LO	= GM_MIB_CNT_BASE + 48,	/* Octets Received OK Low */
+	GM_RXO_OK_HI	= GM_MIB_CNT_BASE + 56,	/* Octets Received OK High */
+	GM_RXO_ERR_LO	= GM_MIB_CNT_BASE + 64,	/* Octets Received Invalid Low */
+	GM_RXO_ERR_HI	= GM_MIB_CNT_BASE + 72,	/* Octets Received Invalid High */
+	GM_RXF_SHT	= GM_MIB_CNT_BASE + 80,	/* Frames <64 Byte Received OK */
+	GM_RXE_FRAG	= GM_MIB_CNT_BASE + 88,	/* Frames <64 Byte Received with FCS Err */
+	GM_RXF_64B	= GM_MIB_CNT_BASE + 96,	/* 64 Byte Rx Frame */
+	GM_RXF_127B	= GM_MIB_CNT_BASE + 104,	/* 65-127 Byte Rx Frame */
+	GM_RXF_255B	= GM_MIB_CNT_BASE + 112,	/* 128-255 Byte Rx Frame */
+	GM_RXF_511B	= GM_MIB_CNT_BASE + 120,	/* 256-511 Byte Rx Frame */
+	GM_RXF_1023B	= GM_MIB_CNT_BASE + 128,	/* 512-1023 Byte Rx Frame */
+	GM_RXF_1518B	= GM_MIB_CNT_BASE + 136,	/* 1024-1518 Byte Rx Frame */
+	GM_RXF_MAX_SZ	= GM_MIB_CNT_BASE + 144,	/* 1519-MaxSize Byte Rx Frame */
+	GM_RXF_LNG_ERR	= GM_MIB_CNT_BASE + 152,	/* Rx Frame too Long Error */
+	GM_RXF_JAB_PKT	= GM_MIB_CNT_BASE + 160,	/* Rx Jabber Packet Frame */
+	/* GM_MIB_CNT_BASE + 168:	reserved */
+	GM_RXE_FIFO_OV	= GM_MIB_CNT_BASE + 176,	/* Rx FIFO overflow Event */
+	/* GM_MIB_CNT_BASE + 184:	reserved */
+	GM_TXF_UC_OK	= GM_MIB_CNT_BASE + 192,	/* Unicast Frames Xmitted OK */
+	GM_TXF_BC_OK	= GM_MIB_CNT_BASE + 200,	/* Broadcast Frames Xmitted OK */
+	GM_TXF_MPAUSE	= GM_MIB_CNT_BASE + 208,	/* Pause MAC Ctrl Frames Xmitted */
+	GM_TXF_MC_OK	= GM_MIB_CNT_BASE + 216,	/* Multicast Frames Xmitted OK */
+	GM_TXO_OK_LO	= GM_MIB_CNT_BASE + 224,	/* Octets Transmitted OK Low */
+	GM_TXO_OK_HI	= GM_MIB_CNT_BASE + 232,	/* Octets Transmitted OK High */
+	GM_TXF_64B	= GM_MIB_CNT_BASE + 240,	/* 64 Byte Tx Frame */
+	GM_TXF_127B	= GM_MIB_CNT_BASE + 248,	/* 65-127 Byte Tx Frame */
+	GM_TXF_255B	= GM_MIB_CNT_BASE + 256,	/* 128-255 Byte Tx Frame */
+	GM_TXF_511B	= GM_MIB_CNT_BASE + 264,	/* 256-511 Byte Tx Frame */
+	GM_TXF_1023B	= GM_MIB_CNT_BASE + 272,	/* 512-1023 Byte Tx Frame */
+	GM_TXF_1518B	= GM_MIB_CNT_BASE + 280,	/* 1024-1518 Byte Tx Frame */
+	GM_TXF_MAX_SZ	= GM_MIB_CNT_BASE + 288,	/* 1519-MaxSize Byte Tx Frame */
+
+	GM_TXF_COL	= GM_MIB_CNT_BASE + 304,	/* Tx Collision */
+	GM_TXF_LAT_COL	= GM_MIB_CNT_BASE + 312,	/* Tx Late Collision */
+	GM_TXF_ABO_COL	= GM_MIB_CNT_BASE + 320,	/* Tx aborted due to Exces. Col. */
+	GM_TXF_MUL_COL	= GM_MIB_CNT_BASE + 328,	/* Tx Multiple Collision */
+	GM_TXF_SNG_COL	= GM_MIB_CNT_BASE + 336,	/* Tx Single Collision */
+	GM_TXE_FIFO_UR	= GM_MIB_CNT_BASE + 344,	/* Tx FIFO Underrun Event */
+};
+
+/* GMAC Bit Definitions */
+/*	GM_GP_STAT	16 bit r/o	General Purpose Status Register */
+enum {
+	GM_GPSR_SPEED		= 1<<15, /* Bit 15:	Port Speed (1 = 100 Mbps) */
+	GM_GPSR_DUPLEX		= 1<<14, /* Bit 14:	Duplex Mode (1 = Full) */
+	GM_GPSR_FC_TX_DIS	= 1<<13, /* Bit 13:	Tx Flow-Control Mode Disabled */
+	GM_GPSR_LINK_UP		= 1<<12, /* Bit 12:	Link Up Status */
+	GM_GPSR_PAUSE		= 1<<11, /* Bit 11:	Pause State */
+	GM_GPSR_TX_ACTIVE	= 1<<10, /* Bit 10:	Tx in Progress */
+	GM_GPSR_EXC_COL		= 1<<9,	/* Bit  9:	Excessive Collisions Occured */
+	GM_GPSR_LAT_COL		= 1<<8,	/* Bit  8:	Late Collisions Occured */
+
+	GM_GPSR_PHY_ST_CH	= 1<<5,	/* Bit  5:	PHY Status Change */
+	GM_GPSR_GIG_SPEED	= 1<<4,	/* Bit  4:	Gigabit Speed (1 = 1000 Mbps) */
+	GM_GPSR_PART_MODE	= 1<<3,	/* Bit  3:	Partition mode */
+	GM_GPSR_FC_RX_DIS	= 1<<2,	/* Bit  2:	Rx Flow-Control Mode Disabled */
+	GM_GPSR_PROM_EN		= 1<<1,	/* Bit  1:	Promiscuous Mode Enabled */
+};
+
+/*	GM_GP_CTRL	16 bit r/w	General Purpose Control Register */
+enum {
+	GM_GPCR_PROM_ENA	= 1<<14,	/* Bit 14:	Enable Promiscuous Mode */
+	GM_GPCR_FC_TX_DIS	= 1<<13, /* Bit 13:	Disable Tx Flow-Control Mode */
+	GM_GPCR_TX_ENA		= 1<<12, /* Bit 12:	Enable Transmit */
+	GM_GPCR_RX_ENA		= 1<<11, /* Bit 11:	Enable Receive */
+	GM_GPCR_BURST_ENA	= 1<<10, /* Bit 10:	Enable Burst Mode */
+	GM_GPCR_LOOP_ENA	= 1<<9,	/* Bit  9:	Enable MAC Loopback Mode */
+	GM_GPCR_PART_ENA	= 1<<8,	/* Bit  8:	Enable Partition Mode */
+	GM_GPCR_GIGS_ENA	= 1<<7,	/* Bit  7:	Gigabit Speed (1000 Mbps) */
+	GM_GPCR_FL_PASS		= 1<<6,	/* Bit  6:	Force Link Pass */
+	GM_GPCR_DUP_FULL	= 1<<5,	/* Bit  5:	Full Duplex Mode */
+	GM_GPCR_FC_RX_DIS	= 1<<4,	/* Bit  4:	Disable Rx Flow-Control Mode */
+	GM_GPCR_SPEED_100	= 1<<3,   /* Bit  3:	Port Speed 100 Mbps */
+	GM_GPCR_AU_DUP_DIS	= 1<<2,	/* Bit  2:	Disable Auto-Update Duplex */
+	GM_GPCR_AU_FCT_DIS	= 1<<1,	/* Bit  1:	Disable Auto-Update Flow-C. */
+	GM_GPCR_AU_SPD_DIS	= 1<<0,	/* Bit  0:	Disable Auto-Update Speed */
+};
+
+#define GM_GPCR_SPEED_1000	(GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
+#define GM_GPCR_AU_ALL_DIS	(GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
+
+/*	GM_TX_CTRL			16 bit r/w	Transmit Control Register */
+enum {
+	GM_TXCR_FORCE_JAM	= 1<<15, /* Bit 15:	Force Jam / Flow-Control */
+	GM_TXCR_CRC_DIS		= 1<<14, /* Bit 14:	Disable insertion of CRC */
+	GM_TXCR_PAD_DIS		= 1<<13, /* Bit 13:	Disable padding of packets */
+	GM_TXCR_COL_THR_MSK	= 1<<10, /* Bit 12..10:	Collision Threshold */
+};
+
+#define TX_COL_THR(x)		(((x)<<10) & GM_TXCR_COL_THR_MSK)
+#define TX_COL_DEF		0x04
+
+/*	GM_RX_CTRL			16 bit r/w	Receive Control Register */
+enum {
+	GM_RXCR_UCF_ENA	= 1<<15, /* Bit 15:	Enable Unicast filtering */
+	GM_RXCR_MCF_ENA	= 1<<14, /* Bit 14:	Enable Multicast filtering */
+	GM_RXCR_CRC_DIS	= 1<<13, /* Bit 13:	Remove 4-byte CRC */
+	GM_RXCR_PASS_FC	= 1<<12, /* Bit 12:	Pass FC packets to FIFO */
+};
+
+/*	GM_TX_PARAM		16 bit r/w	Transmit Parameter Register */
+enum {
+	GM_TXPA_JAMLEN_MSK	= 0x03<<14,	/* Bit 15..14:	Jam Length */
+	GM_TXPA_JAMIPG_MSK	= 0x1f<<9,	/* Bit 13..9:	Jam IPG */
+	GM_TXPA_JAMDAT_MSK	= 0x1f<<4,	/* Bit  8..4:	IPG Jam to Data */
+	GM_TXPA_BO_LIM_MSK	= 0x0f,		/* Bit  3.. 0: Backoff Limit Mask */
+
+	TX_JAM_LEN_DEF		= 0x03,
+	TX_JAM_IPG_DEF		= 0x0b,
+	TX_IPG_JAM_DEF		= 0x1c,
+	TX_BOF_LIM_DEF		= 0x04,
+};
+
+#define TX_JAM_LEN_VAL(x)	(((x)<<14) & GM_TXPA_JAMLEN_MSK)
+#define TX_JAM_IPG_VAL(x)	(((x)<<9)  & GM_TXPA_JAMIPG_MSK)
+#define TX_IPG_JAM_DATA(x)	(((x)<<4)  & GM_TXPA_JAMDAT_MSK)
+#define TX_BACK_OFF_LIM(x)	((x) & GM_TXPA_BO_LIM_MSK)
+
+
+/*	GM_SERIAL_MODE			16 bit r/w	Serial Mode Register */
+enum {
+	GM_SMOD_DATABL_MSK	= 0x1f<<11, /* Bit 15..11:	Data Blinder (r/o) */
+	GM_SMOD_LIMIT_4		= 1<<10, /* Bit 10:	4 consecutive Tx trials */
+	GM_SMOD_VLAN_ENA	= 1<<9,	/* Bit  9:	Enable VLAN  (Max. Frame Len) */
+	GM_SMOD_JUMBO_ENA	= 1<<8,	/* Bit  8:	Enable Jumbo (Max. Frame Len) */
+	 GM_SMOD_IPG_MSK	= 0x1f	/* Bit 4..0:	Inter-Packet Gap (IPG) */
+};
+
+#define DATA_BLIND_VAL(x)	(((x)<<11) & GM_SMOD_DATABL_MSK)
+#define DATA_BLIND_DEF		0x04
+
+#define IPG_DATA_VAL(x)		(x & GM_SMOD_IPG_MSK)
+#define IPG_DATA_DEF		0x1e
+
+/*	GM_SMI_CTRL			16 bit r/w	SMI Control Register */
+enum {
+	GM_SMI_CT_PHY_A_MSK	= 0x1f<<11,/* Bit 15..11:	PHY Device Address */
+	GM_SMI_CT_REG_A_MSK	= 0x1f<<6,/* Bit 10.. 6:	PHY Register Address */
+	GM_SMI_CT_OP_RD		= 1<<5,	/* Bit  5:	OpCode Read (0=Write)*/
+	GM_SMI_CT_RD_VAL	= 1<<4,	/* Bit  4:	Read Valid (Read completed) */
+	GM_SMI_CT_BUSY		= 1<<3,	/* Bit  3:	Busy (Operation in progress) */
+};
+
+#define GM_SMI_CT_PHY_AD(x)	(((x)<<11) & GM_SMI_CT_PHY_A_MSK)
+#define GM_SMI_CT_REG_AD(x)	(((x)<<6) & GM_SMI_CT_REG_A_MSK)
+
+/*	GM_PHY_ADDR				16 bit r/w	GPHY Address Register */
+enum {
+	GM_PAR_MIB_CLR	= 1<<5,	/* Bit  5:	Set MIB Clear Counter Mode */
+	GM_PAR_MIB_TST	= 1<<4,	/* Bit  4:	MIB Load Counter (Test Mode) */
+};
+
+/* Receive Frame Status Encoding */
+enum {
+	GMR_FS_LEN	= 0xffff<<16, /* Bit 31..16:	Rx Frame Length */
+	GMR_FS_VLAN	= 1<<13, /* VLAN Packet */
+	GMR_FS_JABBER	= 1<<12, /* Jabber Packet */
+	GMR_FS_UN_SIZE	= 1<<11, /* Undersize Packet */
+	GMR_FS_MC	= 1<<10, /* Multicast Packet */
+	GMR_FS_BC	= 1<<9,  /* Broadcast Packet */
+	GMR_FS_RX_OK	= 1<<8,  /* Receive OK (Good Packet) */
+	GMR_FS_GOOD_FC	= 1<<7,  /* Good Flow-Control Packet */
+	GMR_FS_BAD_FC	= 1<<6,  /* Bad  Flow-Control Packet */
+	GMR_FS_MII_ERR	= 1<<5,  /* MII Error */
+	GMR_FS_LONG_ERR	= 1<<4,  /* Too Long Packet */
+	GMR_FS_FRAGMENT	= 1<<3,  /* Fragment */
+
+	GMR_FS_CRC_ERR	= 1<<1,  /* CRC Error */
+	GMR_FS_RX_FF_OV	= 1<<0,  /* Rx FIFO Overflow */
+
+	GMR_FS_ANY_ERR	= GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR |
+			  GMR_FS_FRAGMENT | GMR_FS_LONG_ERR |
+		  	  GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
+			  GMR_FS_UN_SIZE | GMR_FS_JABBER,
+};
+
+/*	RX_GMF_CTRL_T	32 bit	Rx GMAC FIFO Control/Test */
+enum {
+	RX_TRUNC_ON	= 1<<27,  	/* enable  packet truncation */
+	RX_TRUNC_OFF	= 1<<26, 	/* disable packet truncation */
+	RX_VLAN_STRIP_ON = 1<<25,	/* enable  VLAN stripping */
+	RX_VLAN_STRIP_OFF = 1<<24,	/* disable VLAN stripping */
+
+	GMF_WP_TST_ON	= 1<<14,	/* Write Pointer Test On */
+	GMF_WP_TST_OFF	= 1<<13,	/* Write Pointer Test Off */
+	GMF_WP_STEP	= 1<<12,	/* Write Pointer Step/Increment */
+
+	GMF_RP_TST_ON	= 1<<10,	/* Read Pointer Test On */
+	GMF_RP_TST_OFF	= 1<<9,		/* Read Pointer Test Off */
+	GMF_RP_STEP	= 1<<8,		/* Read Pointer Step/Increment */
+	GMF_RX_F_FL_ON	= 1<<7,		/* Rx FIFO Flush Mode On */
+	GMF_RX_F_FL_OFF	= 1<<6,		/* Rx FIFO Flush Mode Off */
+	GMF_CLI_RX_FO	= 1<<5,		/* Clear IRQ Rx FIFO Overrun */
+	GMF_CLI_RX_C	= 1<<4,		/* Clear IRQ Rx Frame Complete */
+
+	GMF_OPER_ON	= 1<<3,		/* Operational Mode On */
+	GMF_OPER_OFF	= 1<<2,		/* Operational Mode Off */
+	GMF_RST_CLR	= 1<<1,		/* Clear GMAC FIFO Reset */
+	GMF_RST_SET	= 1<<0,		/* Set   GMAC FIFO Reset */
+
+	RX_GMF_FL_THR_DEF = 0xa,	/* flush threshold (default) */
+
+	GMF_RX_CTRL_DEF	= GMF_OPER_ON | GMF_RX_F_FL_ON,
+};
+
+
+/*	TX_GMF_CTRL_T	32 bit	Tx GMAC FIFO Control/Test */
+enum {
+	TX_STFW_DIS	= 1<<31,/* Disable Store & Forward (Yukon-EC Ultra) */
+	TX_STFW_ENA	= 1<<30,/* Enable  Store & Forward (Yukon-EC Ultra) */
+
+	TX_VLAN_TAG_ON	= 1<<25,/* enable  VLAN tagging */
+	TX_VLAN_TAG_OFF	= 1<<24,/* disable VLAN tagging */
+
+	GMF_WSP_TST_ON	= 1<<18,/* Write Shadow Pointer Test On */
+	GMF_WSP_TST_OFF	= 1<<17,/* Write Shadow Pointer Test Off */
+	GMF_WSP_STEP	= 1<<16,/* Write Shadow Pointer Step/Increment */
+
+	GMF_CLI_TX_FU	= 1<<6,	/* Clear IRQ Tx FIFO Underrun */
+	GMF_CLI_TX_FC	= 1<<5,	/* Clear IRQ Tx Frame Complete */
+	GMF_CLI_TX_PE	= 1<<4,	/* Clear IRQ Tx Parity Error */
+};
+
+/*	GMAC_TI_ST_CTRL	 8 bit	Time Stamp Timer Ctrl Reg (YUKON only) */
+enum {
+	GMT_ST_START	= 1<<2,	/* Start Time Stamp Timer */
+	GMT_ST_STOP	= 1<<1,	/* Stop  Time Stamp Timer */
+	GMT_ST_CLR_IRQ	= 1<<0,	/* Clear Time Stamp Timer IRQ */
+};
+
+/* B28_Y2_ASF_STAT_CMD		32 bit	ASF Status and Command Reg */
+enum {
+	Y2_ASF_OS_PRES	= 1<<4,	/* ASF operation system present */
+	Y2_ASF_RESET	= 1<<3,	/* ASF system in reset state */
+	Y2_ASF_RUNNING	= 1<<2,	/* ASF system operational */
+	Y2_ASF_CLR_HSTI = 1<<1,	/* Clear ASF IRQ */
+	Y2_ASF_IRQ	= 1<<0,	/* Issue an IRQ to ASF system */
+
+	Y2_ASF_UC_STATE = 3<<2,	/* ASF uC State */
+	Y2_ASF_CLK_HALT	= 0,	/* ASF system clock stopped */
+};
+
+/* B28_Y2_ASF_HOST_COM	32 bit	ASF Host Communication Reg */
+enum {
+	Y2_ASF_CLR_ASFI = 1<<1,	/* Clear host IRQ */
+	Y2_ASF_HOST_IRQ = 1<<0,	/* Issue an IRQ to HOST system */
+};
+
+/*	STAT_CTRL		32 bit	Status BMU control register (Yukon-2 only) */
+enum {
+	SC_STAT_CLR_IRQ	= 1<<4,	/* Status Burst IRQ clear */
+	SC_STAT_OP_ON	= 1<<3,	/* Operational Mode On */
+	SC_STAT_OP_OFF	= 1<<2,	/* Operational Mode Off */
+	SC_STAT_RST_CLR	= 1<<1,	/* Clear Status Unit Reset (Enable) */
+	SC_STAT_RST_SET	= 1<<0,	/* Set   Status Unit Reset */
+};
+
+/*	GMAC_CTRL		32 bit	GMAC Control Reg (YUKON only) */
+enum {
+	GMC_H_BURST_ON	= 1<<7,	/* Half Duplex Burst Mode On */
+	GMC_H_BURST_OFF	= 1<<6,	/* Half Duplex Burst Mode Off */
+	GMC_F_LOOPB_ON	= 1<<5,	/* FIFO Loopback On */
+	GMC_F_LOOPB_OFF	= 1<<4,	/* FIFO Loopback Off */
+	GMC_PAUSE_ON	= 1<<3,	/* Pause On */
+	GMC_PAUSE_OFF	= 1<<2,	/* Pause Off */
+	GMC_RST_CLR	= 1<<1,	/* Clear GMAC Reset */
+	GMC_RST_SET	= 1<<0,	/* Set   GMAC Reset */
+};
+
+/*	GPHY_CTRL		32 bit	GPHY Control Reg (YUKON only) */
+enum {
+	GPC_SEL_BDT	= 1<<28, /* Select Bi-Dir. Transfer for MDC/MDIO */
+	GPC_INT_POL_HI	= 1<<27, /* IRQ Polarity is Active HIGH */
+	GPC_75_OHM	= 1<<26, /* Use 75 Ohm Termination instead of 50 */
+	GPC_DIS_FC	= 1<<25, /* Disable Automatic Fiber/Copper Detection */
+	GPC_DIS_SLEEP	= 1<<24, /* Disable Energy Detect */
+	GPC_HWCFG_M_3	= 1<<23, /* HWCFG_MODE[3] */
+	GPC_HWCFG_M_2	= 1<<22, /* HWCFG_MODE[2] */
+	GPC_HWCFG_M_1	= 1<<21, /* HWCFG_MODE[1] */
+	GPC_HWCFG_M_0	= 1<<20, /* HWCFG_MODE[0] */
+	GPC_ANEG_0	= 1<<19, /* ANEG[0] */
+	GPC_ENA_XC	= 1<<18, /* Enable MDI crossover */
+	GPC_DIS_125	= 1<<17, /* Disable 125 MHz clock */
+	GPC_ANEG_3	= 1<<16, /* ANEG[3] */
+	GPC_ANEG_2	= 1<<15, /* ANEG[2] */
+	GPC_ANEG_1	= 1<<14, /* ANEG[1] */
+	GPC_ENA_PAUSE	= 1<<13, /* Enable Pause (SYM_OR_REM) */
+	GPC_PHYADDR_4	= 1<<12, /* Bit 4 of Phy Addr */
+	GPC_PHYADDR_3	= 1<<11, /* Bit 3 of Phy Addr */
+	GPC_PHYADDR_2	= 1<<10, /* Bit 2 of Phy Addr */
+	GPC_PHYADDR_1	= 1<<9,	 /* Bit 1 of Phy Addr */
+	GPC_PHYADDR_0	= 1<<8,	 /* Bit 0 of Phy Addr */
+						/* Bits  7..2:	reserved */
+	GPC_RST_CLR	= 1<<1,	/* Clear GPHY Reset */
+	GPC_RST_SET	= 1<<0,	/* Set   GPHY Reset */
+};
+
+/*	GMAC_IRQ_SRC	 8 bit	GMAC Interrupt Source Reg (YUKON only) */
+/*	GMAC_IRQ_MSK	 8 bit	GMAC Interrupt Mask   Reg (YUKON only) */
+enum {
+	GM_IS_TX_CO_OV	= 1<<5,	/* Transmit Counter Overflow IRQ */
+	GM_IS_RX_CO_OV	= 1<<4,	/* Receive Counter Overflow IRQ */
+	GM_IS_TX_FF_UR	= 1<<3,	/* Transmit FIFO Underrun */
+	GM_IS_TX_COMPL	= 1<<2,	/* Frame Transmission Complete */
+	GM_IS_RX_FF_OR	= 1<<1,	/* Receive FIFO Overrun */
+	GM_IS_RX_COMPL	= 1<<0,	/* Frame Reception Complete */
+
+#define GMAC_DEF_MSK     GM_IS_TX_FF_UR
+
+/*	GMAC_LINK_CTRL	16 bit	GMAC Link Control Reg (YUKON only) */
+						/* Bits 15.. 2:	reserved */
+	GMLC_RST_CLR	= 1<<1,	/* Clear GMAC Link Reset */
+	GMLC_RST_SET	= 1<<0,	/* Set   GMAC Link Reset */
+
+
+/*	WOL_CTRL_STAT	16 bit	WOL Control/Status Reg */
+	WOL_CTL_LINK_CHG_OCC		= 1<<15,
+	WOL_CTL_MAGIC_PKT_OCC		= 1<<14,
+	WOL_CTL_PATTERN_OCC		= 1<<13,
+	WOL_CTL_CLEAR_RESULT		= 1<<12,
+	WOL_CTL_ENA_PME_ON_LINK_CHG	= 1<<11,
+	WOL_CTL_DIS_PME_ON_LINK_CHG	= 1<<10,
+	WOL_CTL_ENA_PME_ON_MAGIC_PKT	= 1<<9,
+	WOL_CTL_DIS_PME_ON_MAGIC_PKT	= 1<<8,
+	WOL_CTL_ENA_PME_ON_PATTERN	= 1<<7,
+	WOL_CTL_DIS_PME_ON_PATTERN	= 1<<6,
+	WOL_CTL_ENA_LINK_CHG_UNIT	= 1<<5,
+	WOL_CTL_DIS_LINK_CHG_UNIT	= 1<<4,
+	WOL_CTL_ENA_MAGIC_PKT_UNIT	= 1<<3,
+	WOL_CTL_DIS_MAGIC_PKT_UNIT	= 1<<2,
+	WOL_CTL_ENA_PATTERN_UNIT	= 1<<1,
+	WOL_CTL_DIS_PATTERN_UNIT	= 1<<0,
+};
+
+#define WOL_CTL_DEFAULT				\
+	(WOL_CTL_DIS_PME_ON_LINK_CHG |	\
+	WOL_CTL_DIS_PME_ON_PATTERN |	\
+	WOL_CTL_DIS_PME_ON_MAGIC_PKT |	\
+	WOL_CTL_DIS_LINK_CHG_UNIT |		\
+	WOL_CTL_DIS_PATTERN_UNIT |		\
+	WOL_CTL_DIS_MAGIC_PKT_UNIT)
+
+/*	WOL_MATCH_CTL	 8 bit	WOL Match Control Reg */
+#define WOL_CTL_PATT_ENA(x)	(1 << (x))
+
+
+/* Control flags */
+enum {
+	UDPTCP	= 1<<0,
+	CALSUM	= 1<<1,
+	WR_SUM	= 1<<2,
+	INIT_SUM= 1<<3,
+	LOCK_SUM= 1<<4,
+	INS_VLAN= 1<<5,
+	FRC_STAT= 1<<6,
+	EOP	= 1<<7,
+};
+
+enum {
+	HW_OWNER 	= 1<<7,
+	OP_TCPWRITE	= 0x11,
+	OP_TCPSTART	= 0x12,
+	OP_TCPINIT	= 0x14,
+	OP_TCPLCK	= 0x18,
+	OP_TCPCHKSUM	= OP_TCPSTART,
+	OP_TCPIS	= OP_TCPINIT | OP_TCPSTART,
+	OP_TCPLW	= OP_TCPLCK | OP_TCPWRITE,
+	OP_TCPLSW	= OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE,
+	OP_TCPLISW	= OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE,
+
+	OP_ADDR64	= 0x21,
+	OP_VLAN		= 0x22,
+	OP_ADDR64VLAN	= OP_ADDR64 | OP_VLAN,
+	OP_LRGLEN	= 0x24,
+	OP_LRGLENVLAN	= OP_LRGLEN | OP_VLAN,
+	OP_BUFFER	= 0x40,
+	OP_PACKET	= 0x41,
+	OP_LARGESEND	= 0x43,
+
+/* YUKON-2 STATUS opcodes defines */
+	OP_RXSTAT	= 0x60,
+	OP_RXTIMESTAMP	= 0x61,
+	OP_RXVLAN	= 0x62,
+	OP_RXCHKS	= 0x64,
+	OP_RXCHKSVLAN	= OP_RXCHKS | OP_RXVLAN,
+	OP_RXTIMEVLAN	= OP_RXTIMESTAMP | OP_RXVLAN,
+	OP_RSS_HASH	= 0x65,
+	OP_TXINDEXLE	= 0x68,
+};
+
+/* Yukon 2 hardware interface
+ * Not tested on big endian
+ */
+struct sky2_tx_le {
+	union {
+		__le32	addr;
+		struct {
+			__le16	offset;
+			__le16	start;
+		} csum  __attribute((packed));
+		struct {
+			__le16	size;
+			__le16	rsvd;
+		} tso  __attribute((packed));
+	} tx;
+	__le16	length;	/* also vlan tag or checksum start */
+	u8	ctrl;
+	u8	opcode;
+} __attribute((packed));
+
+struct sky2_rx_le {
+	__le32	addr;
+	__le16	length;
+	u8	ctrl;
+	u8	opcode;
+} __attribute((packed));;
+
+struct sky2_status_le {
+	__le32	status;	/* also checksum */
+	__le16	length;	/* also vlan tag */
+	u8	link;
+	u8	opcode;
+} __attribute((packed));
+
+struct tx_ring_info {
+	struct sk_buff	*skb;
+	DECLARE_PCI_UNMAP_ADDR(mapaddr);
+	u16		idx;
+};
+
+struct ring_info {
+	struct sk_buff	*skb;
+	dma_addr_t	mapaddr;
+};
+
+struct sky2_port {
+	struct sky2_hw	     *hw;
+	struct net_device    *netdev;
+	unsigned	     port;
+	u32		     msg_enable;
+
+	spinlock_t	     tx_lock  ____cacheline_aligned_in_smp;
+	struct tx_ring_info  *tx_ring;
+	struct sky2_tx_le    *tx_le;
+	u16		     tx_cons;		/* next le to check */
+	u16		     tx_prod;		/* next le to use */
+	u32		     tx_addr64;
+	u16		     tx_pending;
+	u16		     tx_last_put;
+	u16		     tx_last_mss;
+
+	struct ring_info     *rx_ring ____cacheline_aligned_in_smp;
+	struct sky2_rx_le    *rx_le;
+	u32		     rx_addr64;
+	u16		     rx_next;		/* next re to check */
+	u16		     rx_put;		/* next le index to use */
+	u16		     rx_pending;
+	u16		     rx_last_put;
+	u16		     rx_bufsize;
+#ifdef SKY2_VLAN_TAG_USED
+	u16		     rx_tag;
+	struct vlan_group    *vlgrp;
+#endif
+
+	dma_addr_t	     rx_le_map;
+	dma_addr_t	     tx_le_map;
+	u32		     advertising;	/* ADVERTISED_ bits */
+	u16		     speed;	/* SPEED_1000, SPEED_100, ... */
+	u8		     autoneg;	/* AUTONEG_ENABLE, AUTONEG_DISABLE */
+	u8		     duplex;	/* DUPLEX_HALF, DUPLEX_FULL */
+	u8		     rx_pause;
+	u8		     tx_pause;
+	u8		     rx_csum;
+	u8		     wol;
+
+	struct net_device_stats net_stats;
+
+	struct work_struct   phy_task;
+	struct semaphore     phy_sema;
+};
+
+struct sky2_hw {
+	void __iomem  	     *regs;
+	struct pci_dev	     *pdev;
+	u32		     intr_mask;
+	struct net_device    *dev[2];
+
+	int		     pm_cap;
+	u8	     	     chip_id;
+	u8		     chip_rev;
+	u8		     copper;
+	u8		     ports;
+
+	struct sky2_status_le *st_le;
+	u32		     st_idx;
+	dma_addr_t   	     st_dma;
+};
+
+/* Register accessor for memory mapped device */
+static inline u32 sky2_read32(const struct sky2_hw *hw, unsigned reg)
+{
+	return readl(hw->regs + reg);
+}
+
+static inline u16 sky2_read16(const struct sky2_hw *hw, unsigned reg)
+{
+	return readw(hw->regs + reg);
+}
+
+static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg)
+{
+	return readb(hw->regs + reg);
+}
+
+/* This should probably go away, bus based tweeks suck */
+static inline int is_pciex(const struct sky2_hw *hw)
+{
+	u32 status;
+	pci_read_config_dword(hw->pdev, PCI_DEV_STATUS, &status);
+	return (status & PCI_OS_PCI_X) == 0;
+}
+
+static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val)
+{
+	writel(val, hw->regs + reg);
+}
+
+static inline void sky2_write16(const struct sky2_hw *hw, unsigned reg, u16 val)
+{
+	writew(val, hw->regs + reg);
+}
+
+static inline void sky2_write8(const struct sky2_hw *hw, unsigned reg, u8 val)
+{
+	writeb(val, hw->regs + reg);
+}
+
+/* Yukon PHY related registers */
+#define SK_GMAC_REG(port,reg) \
+	(BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
+#define GM_PHY_RETRIES	100
+
+static inline u16 gma_read16(const struct sky2_hw *hw, unsigned port, unsigned reg)
+{
+	return sky2_read16(hw, SK_GMAC_REG(port,reg));
+}
+
+static inline u32 gma_read32(struct sky2_hw *hw, unsigned port, unsigned reg)
+{
+	unsigned base = SK_GMAC_REG(port, reg);
+	return (u32) sky2_read16(hw, base)
+		| (u32) sky2_read16(hw, base+4) << 16;
+}
+
+static inline void gma_write16(const struct sky2_hw *hw, unsigned port, int r, u16 v)
+{
+	sky2_write16(hw, SK_GMAC_REG(port,r), v);
+}
+
+static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg,
+				    const u8 *addr)
+{
+	gma_write16(hw, port, reg,  (u16) addr[0] | ((u16) addr[1] << 8));
+	gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
+	gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
+}
+#endif