Move USB network drivers to drivers/net/usb.

It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus.  When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer.  Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 338 insertions, 0 deletions

diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig
new file mode 100644
index 00000000000..3de564b2314
--- /dev/null
+++ b/drivers/net/usb/Kconfig
@@ -0,0 +1,338 @@
+#
+# USB Network devices configuration
+#
+comment "Networking support is needed for USB Network Adapter support"
+	depends on USB && !NET
+
+menu "USB Network Adapters"
+	depends on USB && NET
+
+config USB_CATC
+	tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	select CRC32
+	---help---
+	  Say Y if you want to use one of the following 10Mbps USB Ethernet
+	  device based on the EL1210A chip. Supported devices are:
+	  Belkin F5U011
+	  Belkin F5U111
+	  CATC NetMate
+	  CATC NetMate II
+	  smartBridges smartNIC
+
+	  This driver makes the adapter appear as a normal Ethernet interface,
+	  typically on eth0, if it is the only ethernet device, or perhaps on
+	  eth1, if you have a PCI or ISA ethernet card installed.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called catc.
+
+config USB_KAWETH
+	tristate "USB KLSI KL5USB101-based ethernet device support"
+	---help---
+	  Say Y here if you want to use one of the following 10Mbps only
+	  USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
+	  3Com 3C19250
+	  ADS USB-10BT
+	  ATEN USB Ethernet
+	  ASANTE USB To Ethernet Adapter
+	  AOX Endpoints USB Ethernet
+	  Correga K.K.
+	  D-Link DSB-650C and DU-E10
+	  Entrega / Portgear E45
+	  I-O DATA USB-ET/T
+	  Jaton USB Ethernet Device Adapter
+	  Kingston Technology USB Ethernet Adapter
+	  Linksys USB10T
+	  Mobility USB-Ethernet Adapter
+	  NetGear EA-101
+	  Peracom Enet and Enet2
+	  Portsmith Express Ethernet Adapter
+	  Shark Pocket Adapter
+	  SMC 2202USB
+	  Sony Vaio port extender
+
+	  This driver is likely to work with most 10Mbps only USB Ethernet
+	  adapters, including some "no brand" devices. It does NOT work on
+	  SmartBridges smartNIC or on Belkin F5U111 devices - you should use
+	  the CATC NetMate driver for those. If you are not sure which one
+	  you need, select both, and the correct one should be selected for
+	  you.
+
+	  This driver makes the adapter appear as a normal Ethernet interface,
+	  typically on eth0, if it is the only ethernet device, or perhaps on
+	  eth1, if you have a PCI or ISA ethernet card installed.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called kaweth.
+
+config USB_PEGASUS
+	tristate "USB Pegasus/Pegasus-II based ethernet device support"
+	select MII
+	---help---
+	  Say Y here if you know you have Pegasus or Pegasus-II based adapter.
+	  If in doubt then look at <file:drivers/usb/net/pegasus.h> for the
+	  complete list of supported devices.
+
+	  If your particular adapter is not in the list and you are _sure_ it
+	  is Pegasus or Pegasus II based then send me
+	  <petkan@users.sourceforge.net> vendor and device IDs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pegasus.
+
+config USB_RTL8150
+	tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
+	depends on EXPERIMENTAL
+	select MII
+	help
+	  Say Y here if you have RTL8150 based usb-ethernet adapter.
+	  Send me <petkan@users.sourceforge.net> any comments you may have.
+	  You can also check for updates at <http://pegasus2.sourceforge.net/>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rtl8150.
+
+config USB_USBNET_MII
+	tristate
+	default n
+
+config USB_USBNET
+	tristate "Multi-purpose USB Networking Framework"
+	select MII if USB_USBNET_MII != n
+	---help---
+	  This driver supports several kinds of network links over USB,
+	  with "minidrivers" built around a common network driver core
+	  that supports deep queues for efficient transfers.  (This gives
+	  better performance with small packets and at high speeds).
+
+	  The USB host runs "usbnet", and the other end of the link might be:
+
+	  - Another USB host, when using USB "network" or "data transfer"
+	    cables.  These are often used to network laptops to PCs, like
+	    "Laplink" parallel cables or some motherboards.  These rely
+	    on specialized chips from many suppliers.
+
+	  - An intelligent USB gadget, perhaps embedding a Linux system.
+	    These include PDAs running Linux (iPaq, Yopy, Zaurus, and
+	    others), and devices that interoperate using the standard
+	    CDC-Ethernet specification (including many cable modems).
+
+	  - Network adapter hardware (like those for 10/100 Ethernet) which
+	    uses this driver framework.
+
+	  The link will appear with a name like "usb0", when the link is
+	  a two-node link, or "eth0" for most CDC-Ethernet devices.  Those
+	  two-node links are most easily managed with Ethernet Bridging
+	  (CONFIG_BRIDGE) instead of routing.
+
+	  For more information see <http://www.linux-usb.org/usbnet/>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called usbnet.
+
+config USB_NET_AX8817X
+	tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
+	depends on USB_USBNET && NET_ETHERNET
+	select CRC32
+	select USB_USBNET_MII
+	default y
+	help
+	  This option adds support for ASIX AX88xxx based USB 2.0
+	  10/100 Ethernet adapters.
+
+ 	  This driver should work with at least the following devices:
+	    * Aten UC210T
+	    * ASIX AX88172
+	    * Billionton Systems, USB2AR
+	    * Buffalo LUA-U2-KTX
+	    * Corega FEther USB2-TX
+	    * D-Link DUB-E100
+	    * Hawking UF200
+	    * Linksys USB200M
+	    * Netgear FA120
+	    * Sitecom LN-029
+	    * Intellinet USB 2.0 Ethernet
+	    * ST Lab USB 2.0 Ethernet
+	    * TrendNet TU2-ET100
+
+	  This driver creates an interface named "ethX", where X depends on
+	  what other networking devices you have in use.
+
+
+config USB_NET_CDCETHER
+	tristate "CDC Ethernet support (smart devices such as cable modems)"
+	depends on USB_USBNET
+	default y
+	help
+	  This option supports devices conforming to the Communication Device
+	  Class (CDC) Ethernet Control Model, a specification that's easy to
+	  implement in device firmware.  The CDC specifications are available
+	  from <http://www.usb.org/>.
+
+	  CDC Ethernet is an implementation option for DOCSIS cable modems
+	  that support USB connectivity, used for non-Microsoft USB hosts.
+	  The Linux-USB CDC Ethernet Gadget driver is an open implementation.
+ 	  This driver should work with at least the following devices:
+
+ 	    * Ericsson PipeRider (all variants)
+ 	    * Motorola (DM100 and SB4100)
+ 	    * Broadcom Cable Modem (reference design)
+ 	    * Toshiba PCX1100U
+	    * ...
+
+	  This driver creates an interface named "ethX", where X depends on
+	  what other networking devices you have in use.  However, if the
+	  IEEE 802 "local assignment" bit is set in the address, a "usbX"
+	  name is used instead.
+
+config USB_NET_DM9601
+	tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
+	depends on USB_USBNET
+	select CRC32
+	select USB_USBNET_MII
+	help
+	  This option adds support for Davicom DM9601 based USB 1.1
+	  10/100 Ethernet adapters.
+
+config USB_NET_GL620A
+	tristate "GeneSys GL620USB-A based cables"
+	depends on USB_USBNET
+	help
+	  Choose this option if you're using a host-to-host cable,
+	  or PC2PC motherboard, with this chip.
+
+	  Note that the half-duplex "GL620USB" is not supported.
+
+config USB_NET_NET1080
+	tristate "NetChip 1080 based cables (Laplink, ...)"
+	default y
+	depends on USB_USBNET
+	help
+	  Choose this option if you're using a host-to-host cable based
+	  on this design:  one NetChip 1080 chip and supporting logic,
+	  optionally with LEDs that indicate traffic
+
+config USB_NET_PLUSB
+	tristate "Prolific PL-2301/2302 based cables"
+	# if the handshake/init/reset problems, from original 'plusb',
+	# are ever resolved ... then remove "experimental"
+	depends on USB_USBNET && EXPERIMENTAL
+	help
+	  Choose this option if you're using a host-to-host cable
+	  with one of these chips.
+
+config USB_NET_MCS7830
+	tristate "MosChip MCS7830 based Ethernet adapters"
+	depends on USB_USBNET
+	select USB_USBNET_MII
+	help
+	  Choose this option if you're using a 10/100 Ethernet USB2
+	  adapter based on the MosChip 7830 controller. This includes
+	  adapters marketed under the DeLOCK brand.
+
+config USB_NET_RNDIS_HOST
+	tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
+	depends on USB_USBNET && EXPERIMENTAL
+	select USB_NET_CDCETHER
+	help
+	  This option enables hosting "Remote NDIS" USB networking links,
+	  as encouraged by Microsoft (instead of CDC Ethernet!) for use in
+	  various devices that may only support this protocol.  A variant
+	  of this protocol (with even less public documentation) seems to
+	  be at the root of Microsoft's "ActiveSync" too.
+
+	  Avoid using this protocol unless you have no better options.
+	  The protocol specification is incomplete, and is controlled by
+	  (and for) Microsoft; it isn't an "Open" ecosystem or market.
+
+config USB_NET_CDC_SUBSET
+	tristate "Simple USB Network Links (CDC Ethernet subset)"
+	depends on USB_USBNET
+	default y
+	help
+	  This driver module supports USB network devices that can work
+	  without any device-specific information.  Select it if you have
+	  one of these drivers.
+
+	  Note that while many USB host-to-host cables can work in this mode,
+	  that may mean not being able to talk to Win32 systems or more
+	  commonly not being able to handle certain events (like replugging
+	  the host on the other end) very well.  Also, these devices will
+	  not generally have permanently assigned Ethernet addresses.
+
+config USB_ALI_M5632
+	boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
+	depends on USB_NET_CDC_SUBSET
+	help
+	  Choose this option if you're using a host-to-host cable
+	  based on this design, which supports USB 2.0 high speed.
+
+config USB_AN2720
+	boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
+	depends on USB_NET_CDC_SUBSET
+	help
+	  Choose this option if you're using a host-to-host cable
+	  based on this design.  Note that AnchorChips is now a
+	  Cypress brand.
+
+config USB_BELKIN
+	boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
+	depends on USB_NET_CDC_SUBSET
+	default y
+	help
+	  Choose this option if you're using a host-to-host cable
+	  based on this design:  two NetChip 2890 chips and an Atmel
+	  microcontroller, with LEDs that indicate traffic.
+
+config USB_ARMLINUX
+	boolean "Embedded ARM Linux links (iPaq, ...)"
+	depends on USB_NET_CDC_SUBSET
+	default y
+	help
+	  Choose this option to support the "usb-eth" networking driver
+	  used by most of the ARM Linux community with device controllers
+	  such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
+	  in some PXA versions of the "blob" boot loader.
+
+	  Linux-based "Gumstix" PXA-25x based systems use this protocol
+	  to talk with other Linux systems.
+
+	  Although the ROMs shipped with Sharp Zaurus products use a
+	  different link level framing protocol, you can have them use
+	  this simpler protocol by installing a different kernel.
+
+config USB_EPSON2888
+	boolean "Epson 2888 based firmware (DEVELOPMENT)"
+	depends on USB_NET_CDC_SUBSET
+	help
+	  Choose this option to support the usb networking links used
+	  by some sample firmware from Epson.
+
+config USB_KC2190
+	boolean "KT Technology KC2190 based cables (InstaNet)"
+	depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
+	help
+	  Choose this option if you're using a host-to-host cable
+	  with one of these chips.
+
+config USB_NET_ZAURUS
+	tristate "Sharp Zaurus (stock ROMs) and compatible"
+	depends on USB_USBNET
+	select USB_NET_CDCETHER
+	select CRC32
+	default y
+	help
+	  Choose this option to support the usb networking links used by
+	  Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
+	  This also supports some related device firmware, as used in some
+	  PDAs from Olympus and some cell phones from Motorola.
+
+	  If you install an alternate image, such as the Linux 2.6 based
+	  versions of OpenZaurus, you should no longer need to support this
+	  protocol.  Only the "eth-fd" or "net_fd" drivers in these devices
+	  really need this non-conformant variant of CDC Ethernet (or in
+	  some cases CDC MDLM) protocol, not "g_ether".
+
+
+endmenu