Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h

1 files changed, 964 insertions, 4 deletions

diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 2c52c23107d..78c991aec7f 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -208,6 +208,118 @@ struct wmi_mac_addr {
 	(c_macaddr)[5] = (((pwmi_mac_addr)->word1) >> 8) & 0xff; \
 	} while (0)
 
+struct wmi_cmd_map {
+	u32 init_cmdid;
+	u32 start_scan_cmdid;
+	u32 stop_scan_cmdid;
+	u32 scan_chan_list_cmdid;
+	u32 scan_sch_prio_tbl_cmdid;
+	u32 pdev_set_regdomain_cmdid;
+	u32 pdev_set_channel_cmdid;
+	u32 pdev_set_param_cmdid;
+	u32 pdev_pktlog_enable_cmdid;
+	u32 pdev_pktlog_disable_cmdid;
+	u32 pdev_set_wmm_params_cmdid;
+	u32 pdev_set_ht_cap_ie_cmdid;
+	u32 pdev_set_vht_cap_ie_cmdid;
+	u32 pdev_set_dscp_tid_map_cmdid;
+	u32 pdev_set_quiet_mode_cmdid;
+	u32 pdev_green_ap_ps_enable_cmdid;
+	u32 pdev_get_tpc_config_cmdid;
+	u32 pdev_set_base_macaddr_cmdid;
+	u32 vdev_create_cmdid;
+	u32 vdev_delete_cmdid;
+	u32 vdev_start_request_cmdid;
+	u32 vdev_restart_request_cmdid;
+	u32 vdev_up_cmdid;
+	u32 vdev_stop_cmdid;
+	u32 vdev_down_cmdid;
+	u32 vdev_set_param_cmdid;
+	u32 vdev_install_key_cmdid;
+	u32 peer_create_cmdid;
+	u32 peer_delete_cmdid;
+	u32 peer_flush_tids_cmdid;
+	u32 peer_set_param_cmdid;
+	u32 peer_assoc_cmdid;
+	u32 peer_add_wds_entry_cmdid;
+	u32 peer_remove_wds_entry_cmdid;
+	u32 peer_mcast_group_cmdid;
+	u32 bcn_tx_cmdid;
+	u32 pdev_send_bcn_cmdid;
+	u32 bcn_tmpl_cmdid;
+	u32 bcn_filter_rx_cmdid;
+	u32 prb_req_filter_rx_cmdid;
+	u32 mgmt_tx_cmdid;
+	u32 prb_tmpl_cmdid;
+	u32 addba_clear_resp_cmdid;
+	u32 addba_send_cmdid;
+	u32 addba_status_cmdid;
+	u32 delba_send_cmdid;
+	u32 addba_set_resp_cmdid;
+	u32 send_singleamsdu_cmdid;
+	u32 sta_powersave_mode_cmdid;
+	u32 sta_powersave_param_cmdid;
+	u32 sta_mimo_ps_mode_cmdid;
+	u32 pdev_dfs_enable_cmdid;
+	u32 pdev_dfs_disable_cmdid;
+	u32 roam_scan_mode;
+	u32 roam_scan_rssi_threshold;
+	u32 roam_scan_period;
+	u32 roam_scan_rssi_change_threshold;
+	u32 roam_ap_profile;
+	u32 ofl_scan_add_ap_profile;
+	u32 ofl_scan_remove_ap_profile;
+	u32 ofl_scan_period;
+	u32 p2p_dev_set_device_info;
+	u32 p2p_dev_set_discoverability;
+	u32 p2p_go_set_beacon_ie;
+	u32 p2p_go_set_probe_resp_ie;
+	u32 p2p_set_vendor_ie_data_cmdid;
+	u32 ap_ps_peer_param_cmdid;
+	u32 ap_ps_peer_uapsd_coex_cmdid;
+	u32 peer_rate_retry_sched_cmdid;
+	u32 wlan_profile_trigger_cmdid;
+	u32 wlan_profile_set_hist_intvl_cmdid;
+	u32 wlan_profile_get_profile_data_cmdid;
+	u32 wlan_profile_enable_profile_id_cmdid;
+	u32 wlan_profile_list_profile_id_cmdid;
+	u32 pdev_suspend_cmdid;
+	u32 pdev_resume_cmdid;
+	u32 add_bcn_filter_cmdid;
+	u32 rmv_bcn_filter_cmdid;
+	u32 wow_add_wake_pattern_cmdid;
+	u32 wow_del_wake_pattern_cmdid;
+	u32 wow_enable_disable_wake_event_cmdid;
+	u32 wow_enable_cmdid;
+	u32 wow_hostwakeup_from_sleep_cmdid;
+	u32 rtt_measreq_cmdid;
+	u32 rtt_tsf_cmdid;
+	u32 vdev_spectral_scan_configure_cmdid;
+	u32 vdev_spectral_scan_enable_cmdid;
+	u32 request_stats_cmdid;
+	u32 set_arp_ns_offload_cmdid;
+	u32 network_list_offload_config_cmdid;
+	u32 gtk_offload_cmdid;
+	u32 csa_offload_enable_cmdid;
+	u32 csa_offload_chanswitch_cmdid;
+	u32 chatter_set_mode_cmdid;
+	u32 peer_tid_addba_cmdid;
+	u32 peer_tid_delba_cmdid;
+	u32 sta_dtim_ps_method_cmdid;
+	u32 sta_uapsd_auto_trig_cmdid;
+	u32 sta_keepalive_cmd;
+	u32 echo_cmdid;
+	u32 pdev_utf_cmdid;
+	u32 dbglog_cfg_cmdid;
+	u32 pdev_qvit_cmdid;
+	u32 pdev_ftm_intg_cmdid;
+	u32 vdev_set_keepalive_cmdid;
+	u32 vdev_get_keepalive_cmdid;
+	u32 force_fw_hang_cmdid;
+	u32 gpio_config_cmdid;
+	u32 gpio_output_cmdid;
+};
+
 /*
  * wmi command groups.
  */
@@ -247,7 +359,9 @@ enum wmi_cmd_group {
 #define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1)
 #define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1)
 
-/* Command IDs and commande events. */
+#define WMI_CMD_UNSUPPORTED 0
+
+/* Command IDs and command events for MAIN FW. */
 enum wmi_cmd_id {
 	WMI_INIT_CMDID = 0x1,
 
@@ -488,6 +602,217 @@ enum wmi_event_id {
 	WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO),
 };
 
+/* Command IDs and command events for 10.X firmware */
+enum wmi_10x_cmd_id {
+	WMI_10X_START_CMDID = 0x9000,
+	WMI_10X_END_CMDID = 0x9FFF,
+
+	/* initialize the wlan sub system */
+	WMI_10X_INIT_CMDID,
+
+	/* Scan specific commands */
+
+	WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID,
+	WMI_10X_STOP_SCAN_CMDID,
+	WMI_10X_SCAN_CHAN_LIST_CMDID,
+	WMI_10X_ECHO_CMDID,
+
+	/* PDEV(physical device) specific commands */
+	WMI_10X_PDEV_SET_REGDOMAIN_CMDID,
+	WMI_10X_PDEV_SET_CHANNEL_CMDID,
+	WMI_10X_PDEV_SET_PARAM_CMDID,
+	WMI_10X_PDEV_PKTLOG_ENABLE_CMDID,
+	WMI_10X_PDEV_PKTLOG_DISABLE_CMDID,
+	WMI_10X_PDEV_SET_WMM_PARAMS_CMDID,
+	WMI_10X_PDEV_SET_HT_CAP_IE_CMDID,
+	WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID,
+	WMI_10X_PDEV_SET_BASE_MACADDR_CMDID,
+	WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID,
+	WMI_10X_PDEV_SET_QUIET_MODE_CMDID,
+	WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID,
+	WMI_10X_PDEV_GET_TPC_CONFIG_CMDID,
+
+	/* VDEV(virtual device) specific commands */
+	WMI_10X_VDEV_CREATE_CMDID,
+	WMI_10X_VDEV_DELETE_CMDID,
+	WMI_10X_VDEV_START_REQUEST_CMDID,
+	WMI_10X_VDEV_RESTART_REQUEST_CMDID,
+	WMI_10X_VDEV_UP_CMDID,
+	WMI_10X_VDEV_STOP_CMDID,
+	WMI_10X_VDEV_DOWN_CMDID,
+	WMI_10X_VDEV_STANDBY_RESPONSE_CMDID,
+	WMI_10X_VDEV_RESUME_RESPONSE_CMDID,
+	WMI_10X_VDEV_SET_PARAM_CMDID,
+	WMI_10X_VDEV_INSTALL_KEY_CMDID,
+
+	/* peer specific commands */
+	WMI_10X_PEER_CREATE_CMDID,
+	WMI_10X_PEER_DELETE_CMDID,
+	WMI_10X_PEER_FLUSH_TIDS_CMDID,
+	WMI_10X_PEER_SET_PARAM_CMDID,
+	WMI_10X_PEER_ASSOC_CMDID,
+	WMI_10X_PEER_ADD_WDS_ENTRY_CMDID,
+	WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID,
+	WMI_10X_PEER_MCAST_GROUP_CMDID,
+
+	/* beacon/management specific commands */
+
+	WMI_10X_BCN_TX_CMDID,
+	WMI_10X_BCN_PRB_TMPL_CMDID,
+	WMI_10X_BCN_FILTER_RX_CMDID,
+	WMI_10X_PRB_REQ_FILTER_RX_CMDID,
+	WMI_10X_MGMT_TX_CMDID,
+
+	/* commands to directly control ba negotiation directly from host. */
+	WMI_10X_ADDBA_CLEAR_RESP_CMDID,
+	WMI_10X_ADDBA_SEND_CMDID,
+	WMI_10X_ADDBA_STATUS_CMDID,
+	WMI_10X_DELBA_SEND_CMDID,
+	WMI_10X_ADDBA_SET_RESP_CMDID,
+	WMI_10X_SEND_SINGLEAMSDU_CMDID,
+
+	/* Station power save specific config */
+	WMI_10X_STA_POWERSAVE_MODE_CMDID,
+	WMI_10X_STA_POWERSAVE_PARAM_CMDID,
+	WMI_10X_STA_MIMO_PS_MODE_CMDID,
+
+	/* set debug log config */
+	WMI_10X_DBGLOG_CFG_CMDID,
+
+	/* DFS-specific commands */
+	WMI_10X_PDEV_DFS_ENABLE_CMDID,
+	WMI_10X_PDEV_DFS_DISABLE_CMDID,
+
+	/* QVIT specific command id */
+	WMI_10X_PDEV_QVIT_CMDID,
+
+	/* Offload Scan and Roaming related  commands */
+	WMI_10X_ROAM_SCAN_MODE,
+	WMI_10X_ROAM_SCAN_RSSI_THRESHOLD,
+	WMI_10X_ROAM_SCAN_PERIOD,
+	WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
+	WMI_10X_ROAM_AP_PROFILE,
+	WMI_10X_OFL_SCAN_ADD_AP_PROFILE,
+	WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE,
+	WMI_10X_OFL_SCAN_PERIOD,
+
+	/* P2P specific commands */
+	WMI_10X_P2P_DEV_SET_DEVICE_INFO,
+	WMI_10X_P2P_DEV_SET_DISCOVERABILITY,
+	WMI_10X_P2P_GO_SET_BEACON_IE,
+	WMI_10X_P2P_GO_SET_PROBE_RESP_IE,
+
+	/* AP power save specific config */
+	WMI_10X_AP_PS_PEER_PARAM_CMDID,
+	WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID,
+
+	/* Rate-control specific commands */
+	WMI_10X_PEER_RATE_RETRY_SCHED_CMDID,
+
+	/* WLAN Profiling commands. */
+	WMI_10X_WLAN_PROFILE_TRIGGER_CMDID,
+	WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
+	WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
+	WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
+	WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
+
+	/* Suspend resume command Ids */
+	WMI_10X_PDEV_SUSPEND_CMDID,
+	WMI_10X_PDEV_RESUME_CMDID,
+
+	/* Beacon filter commands */
+	WMI_10X_ADD_BCN_FILTER_CMDID,
+	WMI_10X_RMV_BCN_FILTER_CMDID,
+
+	/* WOW Specific WMI commands*/
+	WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID,
+	WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID,
+	WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
+	WMI_10X_WOW_ENABLE_CMDID,
+	WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
+
+	/* RTT measurement related cmd */
+	WMI_10X_RTT_MEASREQ_CMDID,
+	WMI_10X_RTT_TSF_CMDID,
+
+	/* transmit beacon by value */
+	WMI_10X_PDEV_SEND_BCN_CMDID,
+
+	/* F/W stats */
+	WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
+	WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
+	WMI_10X_REQUEST_STATS_CMDID,
+
+	/* GPIO Configuration */
+	WMI_10X_GPIO_CONFIG_CMDID,
+	WMI_10X_GPIO_OUTPUT_CMDID,
+
+	WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1,
+};
+
+enum wmi_10x_event_id {
+	WMI_10X_SERVICE_READY_EVENTID = 0x8000,
+	WMI_10X_READY_EVENTID,
+	WMI_10X_START_EVENTID = 0x9000,
+	WMI_10X_END_EVENTID = 0x9FFF,
+
+	/* Scan specific events */
+	WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID,
+	WMI_10X_ECHO_EVENTID,
+	WMI_10X_DEBUG_MESG_EVENTID,
+	WMI_10X_UPDATE_STATS_EVENTID,
+
+	/* Instantaneous RSSI event */
+	WMI_10X_INST_RSSI_STATS_EVENTID,
+
+	/* VDEV specific events */
+	WMI_10X_VDEV_START_RESP_EVENTID,
+	WMI_10X_VDEV_STANDBY_REQ_EVENTID,
+	WMI_10X_VDEV_RESUME_REQ_EVENTID,
+	WMI_10X_VDEV_STOPPED_EVENTID,
+
+	/* peer  specific events */
+	WMI_10X_PEER_STA_KICKOUT_EVENTID,
+
+	/* beacon/mgmt specific events */
+	WMI_10X_HOST_SWBA_EVENTID,
+	WMI_10X_TBTTOFFSET_UPDATE_EVENTID,
+	WMI_10X_MGMT_RX_EVENTID,
+
+	/* Channel stats event */
+	WMI_10X_CHAN_INFO_EVENTID,
+
+	/* PHY Error specific WMI event */
+	WMI_10X_PHYERR_EVENTID,
+
+	/* Roam event to trigger roaming on host */
+	WMI_10X_ROAM_EVENTID,
+
+	/* matching AP found from list of profiles */
+	WMI_10X_PROFILE_MATCH,
+
+	/* debug print message used for tracing FW code while debugging */
+	WMI_10X_DEBUG_PRINT_EVENTID,
+	/* VI spoecific event */
+	WMI_10X_PDEV_QVIT_EVENTID,
+	/* FW code profile data in response to profile request */
+	WMI_10X_WLAN_PROFILE_DATA_EVENTID,
+
+	/*RTT related event ID*/
+	WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID,
+	WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID,
+	WMI_10X_RTT_ERROR_REPORT_EVENTID,
+
+	WMI_10X_WOW_WAKEUP_HOST_EVENTID,
+	WMI_10X_DCS_INTERFERENCE_EVENTID,
+
+	/* TPC config for the current operating channel */
+	WMI_10X_PDEV_TPC_CONFIG_EVENTID,
+
+	WMI_10X_GPIO_INPUT_EVENTID,
+	WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID-1,
+};
+
 enum wmi_phy_mode {
 	MODE_11A        = 0,   /* 11a Mode */
 	MODE_11G        = 1,   /* 11b/g Mode */
@@ -805,6 +1130,46 @@ struct wmi_service_ready_event {
 	struct wlan_host_mem_req mem_reqs[1];
 } __packed;
 
+/* This is the definition from 10.X firmware branch */
+struct wmi_service_ready_event_10x {
+	__le32 sw_version;
+	__le32 abi_version;
+
+	/* WMI_PHY_CAPABILITY */
+	__le32 phy_capability;
+
+	/* Maximum number of frag table entries that SW will populate less 1 */
+	__le32 max_frag_entry;
+	__le32 wmi_service_bitmap[WMI_SERVICE_BM_SIZE];
+	__le32 num_rf_chains;
+
+	/*
+	 * The following field is only valid for service type
+	 * WMI_SERVICE_11AC
+	 */
+	__le32 ht_cap_info; /* WMI HT Capability */
+	__le32 vht_cap_info; /* VHT capability info field of 802.11ac */
+	__le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */
+	__le32 hw_min_tx_power;
+	__le32 hw_max_tx_power;
+
+	struct hal_reg_capabilities hal_reg_capabilities;
+
+	__le32 sys_cap_info;
+	__le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */
+
+	/*
+	 * request to host to allocate a chuck of memory and pss it down to FW
+	 * via WM_INIT. FW uses this as FW extesnsion memory for saving its
+	 * data structures. Only valid for low latency interfaces like PCIE
+	 * where FW can access this memory directly (or) by DMA.
+	 */
+	__le32 num_mem_reqs;
+
+	struct wlan_host_mem_req mem_reqs[1];
+} __packed;
+
+
 #define WMI_SERVICE_READY_TIMEOUT_HZ (5*HZ)
 #define WMI_UNIFIED_READY_TIMEOUT_HZ (5*HZ)
 
@@ -1012,6 +1377,192 @@ struct wmi_resource_config {
 	__le32 max_frag_entries;
 } __packed;
 
+struct wmi_resource_config_10x {
+	/* number of virtual devices (VAPs) to support */
+	__le32 num_vdevs;
+
+	/* number of peer nodes to support */
+	__le32 num_peers;
+
+	/* number of keys per peer */
+	__le32 num_peer_keys;
+
+	/* total number of TX/RX data TIDs */
+	__le32 num_tids;
+
+	/*
+	 * max skid for resolving hash collisions
+	 *
+	 *   The address search table is sparse, so that if two MAC addresses
+	 *   result in the same hash value, the second of these conflicting
+	 *   entries can slide to the next index in the address search table,
+	 *   and use it, if it is unoccupied.  This ast_skid_limit parameter
+	 *   specifies the upper bound on how many subsequent indices to search
+	 *   over to find an unoccupied space.
+	 */
+	__le32 ast_skid_limit;
+
+	/*
+	 * the nominal chain mask for transmit
+	 *
+	 *   The chain mask may be modified dynamically, e.g. to operate AP
+	 *   tx with a reduced number of chains if no clients are associated.
+	 *   This configuration parameter specifies the nominal chain-mask that
+	 *   should be used when not operating with a reduced set of tx chains.
+	 */
+	__le32 tx_chain_mask;
+
+	/*
+	 * the nominal chain mask for receive
+	 *
+	 *   The chain mask may be modified dynamically, e.g. for a client
+	 *   to use a reduced number of chains for receive if the traffic to
+	 *   the client is low enough that it doesn't require downlink MIMO
+	 *   or antenna diversity.
+	 *   This configuration parameter specifies the nominal chain-mask that
+	 *   should be used when not operating with a reduced set of rx chains.
+	 */
+	__le32 rx_chain_mask;
+
+	/*
+	 * what rx reorder timeout (ms) to use for the AC
+	 *
+	 *   Each WMM access class (voice, video, best-effort, background) will
+	 *   have its own timeout value to dictate how long to wait for missing
+	 *   rx MPDUs to arrive before flushing subsequent MPDUs that have
+	 *   already been received.
+	 *   This parameter specifies the timeout in milliseconds for each
+	 *   class.
+	 */
+	__le32 rx_timeout_pri_vi;
+	__le32 rx_timeout_pri_vo;
+	__le32 rx_timeout_pri_be;
+	__le32 rx_timeout_pri_bk;
+
+	/*
+	 * what mode the rx should decap packets to
+	 *
+	 *   MAC can decap to RAW (no decap), native wifi or Ethernet types
+	 *   THis setting also determines the default TX behavior, however TX
+	 *   behavior can be modified on a per VAP basis during VAP init
+	 */
+	__le32 rx_decap_mode;
+
+	/* what is the maximum scan requests than can be queued */
+	__le32 scan_max_pending_reqs;
+
+	/* maximum VDEV that could use BMISS offload */
+	__le32 bmiss_offload_max_vdev;
+
+	/* maximum VDEV that could use offload roaming */
+	__le32 roam_offload_max_vdev;
+
+	/* maximum AP profiles that would push to offload roaming */
+	__le32 roam_offload_max_ap_profiles;
+
+	/*
+	 * how many groups to use for mcast->ucast conversion
+	 *
+	 *   The target's WAL maintains a table to hold information regarding
+	 *   which peers belong to a given multicast group, so that if
+	 *   multicast->unicast conversion is enabled, the target can convert
+	 *   multicast tx frames to a series of unicast tx frames, to each
+	 *   peer within the multicast group.
+	     This num_mcast_groups configuration parameter tells the target how
+	 *   many multicast groups to provide storage for within its multicast
+	 *   group membership table.
+	 */
+	__le32 num_mcast_groups;
+
+	/*
+	 * size to alloc for the mcast membership table
+	 *
+	 *   This num_mcast_table_elems configuration parameter tells the
+	 *   target how many peer elements it needs to provide storage for in
+	 *   its multicast group membership table.
+	 *   These multicast group membership table elements are shared by the
+	 *   multicast groups stored within the table.
+	 */
+	__le32 num_mcast_table_elems;
+
+	/*
+	 * whether/how to do multicast->unicast conversion
+	 *
+	 *   This configuration parameter specifies whether the target should
+	 *   perform multicast --> unicast conversion on transmit, and if so,
+	 *   what to do if it finds no entries in its multicast group
+	 *   membership table for the multicast IP address in the tx frame.
+	 *   Configuration value:
+	 *   0 -> Do not perform multicast to unicast conversion.
+	 *   1 -> Convert multicast frames to unicast, if the IP multicast
+	 *        address from the tx frame is found in the multicast group
+	 *        membership table.  If the IP multicast address is not found,
+	 *        drop the frame.
+	 *   2 -> Convert multicast frames to unicast, if the IP multicast
+	 *        address from the tx frame is found in the multicast group
+	 *        membership table.  If the IP multicast address is not found,
+	 *        transmit the frame as multicast.
+	 */
+	__le32 mcast2ucast_mode;
+
+	/*
+	 * how much memory to allocate for a tx PPDU dbg log
+	 *
+	 *   This parameter controls how much memory the target will allocate
+	 *   to store a log of tx PPDU meta-information (how large the PPDU
+	 *   was, when it was sent, whether it was successful, etc.)
+	 */
+	__le32 tx_dbg_log_size;
+
+	/* how many AST entries to be allocated for WDS */
+	__le32 num_wds_entries;
+
+	/*
+	 * MAC DMA burst size, e.g., For target PCI limit can be
+	 * 0 -default, 1 256B
+	 */
+	__le32 dma_burst_size;
+
+	/*
+	 * Fixed delimiters to be inserted after every MPDU to
+	 * account for interface latency to avoid underrun.
+	 */
+	__le32 mac_aggr_delim;
+
+	/*
+	 *   determine whether target is responsible for detecting duplicate
+	 *   non-aggregate MPDU and timing out stale fragments.
+	 *
+	 *   A-MPDU reordering is always performed on the target.
+	 *
+	 *   0: target responsible for frag timeout and dup checking
+	 *   1: host responsible for frag timeout and dup checking
+	 */
+	__le32 rx_skip_defrag_timeout_dup_detection_check;
+
+	/*
+	 * Configuration for VoW :
+	 * No of Video Nodes to be supported
+	 * and Max no of descriptors for each Video link (node).
+	 */
+	__le32 vow_config;
+
+	/* Number of msdu descriptors target should use */
+	__le32 num_msdu_desc;
+
+	/*
+	 * Max. number of Tx fragments per MSDU
+	 *  This parameter controls the max number of Tx fragments per MSDU.
+	 *  This is sent by the target as part of the WMI_SERVICE_READY event
+	 *  and is overriden by the OS shim as required.
+	 */
+	__le32 max_frag_entries;
+} __packed;
+
+
+#define NUM_UNITS_IS_NUM_VDEVS   0x1
+#define NUM_UNITS_IS_NUM_PEERS   0x2
+
 /* strucutre describing host memory chunk. */
 struct host_memory_chunk {
 	/* id of the request that is passed up in service ready */
@@ -1033,6 +1584,18 @@ struct wmi_init_cmd {
 	struct host_memory_chunk host_mem_chunks[1];
 } __packed;
 
+/* _10x stucture is from 10.X FW API */
+struct wmi_init_cmd_10x {
+	struct wmi_resource_config_10x resource_config;
+	__le32 num_host_mem_chunks;
+
+	/*
+	 * variable number of host memory chunks.
+	 * This should be the last element in the structure
+	 */
+	struct host_memory_chunk host_mem_chunks[1];
+} __packed;
+
 /* TLV for channel list */
 struct wmi_chan_list {
 	__le32 tag; /* WMI_CHAN_LIST_TAG */
@@ -1152,6 +1715,88 @@ struct wmi_start_scan_cmd {
 	 */
 } __packed;
 
+/* This is the definition from 10.X firmware branch */
+struct wmi_start_scan_cmd_10x {
+	/* Scan ID */
+	__le32 scan_id;
+
+	/* Scan requestor ID */
+	__le32 scan_req_id;
+
+	/* VDEV id(interface) that is requesting scan */
+	__le32 vdev_id;
+
+	/* Scan Priority, input to scan scheduler */
+	__le32 scan_priority;
+
+	/* Scan events subscription */
+	__le32 notify_scan_events;
+
+	/* dwell time in msec on active channels */
+	__le32 dwell_time_active;
+
+	/* dwell time in msec on passive channels */
+	__le32 dwell_time_passive;
+
+	/*
+	 * min time in msec on the BSS channel,only valid if atleast one
+	 * VDEV is active
+	 */
+	__le32 min_rest_time;
+
+	/*
+	 * max rest time in msec on the BSS channel,only valid if at least
+	 * one VDEV is active
+	 */
+	/*
+	 * the scanner will rest on the bss channel at least min_rest_time
+	 * after min_rest_time the scanner will start checking for tx/rx
+	 * activity on all VDEVs. if there is no activity the scanner will
+	 * switch to off channel. if there is activity the scanner will let
+	 * the radio on the bss channel until max_rest_time expires.at
+	 * max_rest_time scanner will switch to off channel irrespective of
+	 * activity. activity is determined by the idle_time parameter.
+	 */
+	__le32 max_rest_time;
+
+	/*
+	 * time before sending next set of probe requests.
+	 * The scanner keeps repeating probe requests transmission with
+	 * period specified by repeat_probe_time.
+	 * The number of probe requests specified depends on the ssid_list
+	 * and bssid_list
+	 */
+	__le32 repeat_probe_time;
+
+	/* time in msec between 2 consequetive probe requests with in a set. */
+	__le32 probe_spacing_time;
+
+	/*
+	 * data inactivity time in msec on bss channel that will be used by
+	 * scanner for measuring the inactivity.
+	 */
+	__le32 idle_time;
+
+	/* maximum time in msec allowed for scan  */
+	__le32 max_scan_time;
+
+	/*
+	 * delay in msec before sending first probe request after switching
+	 * to a channel
+	 */
+	__le32 probe_delay;
+
+	/* Scan control flags */
+	__le32 scan_ctrl_flags;
+
+	/*
+	 * TLV (tag length value )  paramerters follow the scan_cmd structure.
+	 * TLV can contain channel list, bssid list, ssid list and
+	 * ie. the TLV tags are defined above;
+	 */
+} __packed;
+
+
 struct wmi_ssid_arg {
 	int len;
 	const u8 *ssid;
@@ -1509,6 +2154,60 @@ struct wmi_csa_event {
 #define VDEV_DEFAULT_STATS_UPDATE_PERIOD    500
 #define PEER_DEFAULT_STATS_UPDATE_PERIOD    500
 
+struct wmi_pdev_param_map {
+	u32 tx_chain_mask;
+	u32 rx_chain_mask;
+	u32 txpower_limit2g;
+	u32 txpower_limit5g;
+	u32 txpower_scale;
+	u32 beacon_gen_mode;
+	u32 beacon_tx_mode;
+	u32 resmgr_offchan_mode;
+	u32 protection_mode;
+	u32 dynamic_bw;
+	u32 non_agg_sw_retry_th;
+	u32 agg_sw_retry_th;
+	u32 sta_kickout_th;
+	u32 ac_aggrsize_scaling;
+	u32 ltr_enable;
+	u32 ltr_ac_latency_be;
+	u32 ltr_ac_latency_bk;
+	u32 ltr_ac_latency_vi;
+	u32 ltr_ac_latency_vo;
+	u32 ltr_ac_latency_timeout;
+	u32 ltr_sleep_override;
+	u32 ltr_rx_override;
+	u32 ltr_tx_activity_timeout;
+	u32 l1ss_enable;
+	u32 dsleep_enable;
+	u32 pcielp_txbuf_flush;
+	u32 pcielp_txbuf_watermark;
+	u32 pcielp_txbuf_tmo_en;
+	u32 pcielp_txbuf_tmo_value;
+	u32 pdev_stats_update_period;
+	u32 vdev_stats_update_period;
+	u32 peer_stats_update_period;
+	u32 bcnflt_stats_update_period;
+	u32 pmf_qos;
+	u32 arp_ac_override;
+	u32 arpdhcp_ac_override;
+	u32 dcs;
+	u32 ani_enable;
+	u32 ani_poll_period;
+	u32 ani_listen_period;
+	u32 ani_ofdm_level;
+	u32 ani_cck_level;
+	u32 dyntxchain;
+	u32 proxy_sta;
+	u32 idle_ps_config;
+	u32 power_gating_sleep;
+	u32 fast_channel_reset;
+	u32 burst_dur;
+	u32 burst_enable;
+};
+
+#define WMI_PDEV_PARAM_UNSUPPORTED 0
+
 enum wmi_pdev_param {
 	/* TX chian mask */
 	WMI_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
@@ -1608,6 +2307,97 @@ enum wmi_pdev_param {
 	WMI_PDEV_PARAM_POWER_GATING_SLEEP,
 };
 
+enum wmi_10x_pdev_param {
+	/* TX chian mask */
+	WMI_10X_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
+	/* RX chian mask */
+	WMI_10X_PDEV_PARAM_RX_CHAIN_MASK,
+	/* TX power limit for 2G Radio */
+	WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G,
+	/* TX power limit for 5G Radio */
+	WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G,
+	/* TX power scale */
+	WMI_10X_PDEV_PARAM_TXPOWER_SCALE,
+	/* Beacon generation mode . 0: host, 1: target   */
+	WMI_10X_PDEV_PARAM_BEACON_GEN_MODE,
+	/* Beacon generation mode . 0: staggered 1: bursted   */
+	WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
+	/*
+	 * Resource manager off chan mode .
+	 * 0: turn off off chan mode. 1: turn on offchan mode
+	 */
+	WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
+	/*
+	 * Protection mode:
+	 * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
+	 */
+	WMI_10X_PDEV_PARAM_PROTECTION_MODE,
+	/* Dynamic bandwidth 0: disable 1: enable */
+	WMI_10X_PDEV_PARAM_DYNAMIC_BW,
+	/* Non aggregrate/ 11g sw retry threshold.0-disable */
+	WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
+	/* aggregrate sw retry threshold. 0-disable*/
+	WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH,
+	/* Station kickout threshold (non of consecutive failures).0-disable */
+	WMI_10X_PDEV_PARAM_STA_KICKOUT_TH,
+	/* Aggerate size scaling configuration per AC */
+	WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING,
+	/* LTR enable */
+	WMI_10X_PDEV_PARAM_LTR_ENABLE,
+	/* LTR latency for BE, in us */
+	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE,
+	/* LTR latency for BK, in us */
+	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK,
+	/* LTR latency for VI, in us */
+	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI,
+	/* LTR latency for VO, in us  */
+	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO,
+	/* LTR AC latency timeout, in ms */
+	WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
+	/* LTR platform latency override, in us */
+	WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
+	/* LTR-RX override, in us */
+	WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE,
+	/* Tx activity timeout for LTR, in us */
+	WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
+	/* L1SS state machine enable */
+	WMI_10X_PDEV_PARAM_L1SS_ENABLE,
+	/* Deep sleep state machine enable */
+	WMI_10X_PDEV_PARAM_DSLEEP_ENABLE,
+	/* pdev level stats update period in ms */
+	WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
+	/* vdev level stats update period in ms */
+	WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
+	/* peer level stats update period in ms */
+	WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
+	/* beacon filter status update period */
+	WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
+	/* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
+	WMI_10X_PDEV_PARAM_PMF_QOS,
+	/* Access category on which ARP and DHCP frames are sent */
+	WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE,
+	/* DCS configuration */
+	WMI_10X_PDEV_PARAM_DCS,
+	/* Enable/Disable ANI on target */
+	WMI_10X_PDEV_PARAM_ANI_ENABLE,
+	/* configure the ANI polling period */
+	WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD,
+	/* configure the ANI listening period */
+	WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD,
+	/* configure OFDM immunity level */
+	WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL,
+	/* configure CCK immunity level */
+	WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL,
+	/* Enable/Disable CDD for 1x1 STAs in rate control module */
+	WMI_10X_PDEV_PARAM_DYNTXCHAIN,
+	/* Enable/Disable Fast channel reset*/
+	WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET,
+	/* Set Bursting DUR */
+	WMI_10X_PDEV_PARAM_BURST_DUR,
+	/* Set Bursting Enable*/
+	WMI_10X_PDEV_PARAM_BURST_ENABLE,
+};
+
 struct wmi_pdev_set_param_cmd {
 	__le32 param_id;
 	__le32 param_value;
@@ -2132,6 +2922,61 @@ enum wmi_rate_preamble {
 /* Value to disable fixed rate setting */
 #define WMI_FIXED_RATE_NONE    (0xff)
 
+struct wmi_vdev_param_map {
+	u32 rts_threshold;
+	u32 fragmentation_threshold;
+	u32 beacon_interval;
+	u32 listen_interval;
+	u32 multicast_rate;
+	u32 mgmt_tx_rate;
+	u32 slot_time;
+	u32 preamble;
+	u32 swba_time;
+	u32 wmi_vdev_stats_update_period;
+	u32 wmi_vdev_pwrsave_ageout_time;
+	u32 wmi_vdev_host_swba_interval;
+	u32 dtim_period;
+	u32 wmi_vdev_oc_scheduler_air_time_limit;
+	u32 wds;
+	u32 atim_window;
+	u32 bmiss_count_max;
+	u32 bmiss_first_bcnt;
+	u32 bmiss_final_bcnt;
+	u32 feature_wmm;
+	u32 chwidth;
+	u32 chextoffset;
+	u32 disable_htprotection;
+	u32 sta_quickkickout;
+	u32 mgmt_rate;
+	u32 protection_mode;
+	u32 fixed_rate;
+	u32 sgi;
+	u32 ldpc;
+	u32 tx_stbc;
+	u32 rx_stbc;
+	u32 intra_bss_fwd;
+	u32 def_keyid;
+	u32 nss;
+	u32 bcast_data_rate;
+	u32 mcast_data_rate;
+	u32 mcast_indicate;
+	u32 dhcp_indicate;
+	u32 unknown_dest_indicate;
+	u32 ap_keepalive_min_idle_inactive_time_secs;
+	u32 ap_keepalive_max_idle_inactive_time_secs;
+	u32 ap_keepalive_max_unresponsive_time_secs;
+	u32 ap_enable_nawds;
+	u32 mcast2ucast_set;
+	u32 enable_rtscts;
+	u32 txbf;
+	u32 packet_powersave;
+	u32 drop_unencry;
+	u32 tx_encap_type;
+	u32 ap_detect_out_of_sync_sleeping_sta_time_secs;
+};
+
+#define WMI_VDEV_PARAM_UNSUPPORTED 0
+
 /* the definition of different VDEV parameters */
 enum wmi_vdev_param {
 	/* RTS Threshold */
@@ -2263,6 +3108,121 @@ enum wmi_vdev_param {
 	WMI_VDEV_PARAM_TX_ENCAP_TYPE,
 };
 
+/* the definition of different VDEV parameters */
+enum wmi_10x_vdev_param {
+	/* RTS Threshold */
+	WMI_10X_VDEV_PARAM_RTS_THRESHOLD = 0x1,
+	/* Fragmentation threshold */
+	WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
+	/* beacon interval in TUs */
+	WMI_10X_VDEV_PARAM_BEACON_INTERVAL,
+	/* Listen interval in TUs */
+	WMI_10X_VDEV_PARAM_LISTEN_INTERVAL,
+	/* muticast rate in Mbps */
+	WMI_10X_VDEV_PARAM_MULTICAST_RATE,
+	/* management frame rate in Mbps */
+	WMI_10X_VDEV_PARAM_MGMT_TX_RATE,
+	/* slot time (long vs short) */
+	WMI_10X_VDEV_PARAM_SLOT_TIME,
+	/* preamble (long vs short) */
+	WMI_10X_VDEV_PARAM_PREAMBLE,
+	/* SWBA time (time before tbtt in msec) */
+	WMI_10X_VDEV_PARAM_SWBA_TIME,
+	/* time period for updating VDEV stats */
+	WMI_10X_VDEV_STATS_UPDATE_PERIOD,
+	/* age out time in msec for frames queued for station in power save */
+	WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME,
+	/*
+	 * Host SWBA interval (time in msec before tbtt for SWBA event
+	 * generation).
+	 */
+	WMI_10X_VDEV_HOST_SWBA_INTERVAL,
+	/* DTIM period (specified in units of num beacon intervals) */
+	WMI_10X_VDEV_PARAM_DTIM_PERIOD,
+	/*
+	 * scheduler air time limit for this VDEV. used by off chan
+	 * scheduler.
+	 */
+	WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
+	/* enable/dsiable WDS for this VDEV  */
+	WMI_10X_VDEV_PARAM_WDS,
+	/* ATIM Window */
+	WMI_10X_VDEV_PARAM_ATIM_WINDOW,
+	/* BMISS max */
+	WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX,
+	/* WMM enables/disabled */
+	WMI_10X_VDEV_PARAM_FEATURE_WMM,
+	/* Channel width */
+	WMI_10X_VDEV_PARAM_CHWIDTH,
+	/* Channel Offset */
+	WMI_10X_VDEV_PARAM_CHEXTOFFSET,
+	/* Disable HT Protection */
+	WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION,
+	/* Quick STA Kickout */
+	WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT,
+	/* Rate to be used with Management frames */
+	WMI_10X_VDEV_PARAM_MGMT_RATE,
+	/* Protection Mode */
+	WMI_10X_VDEV_PARAM_PROTECTION_MODE,
+	/* Fixed rate setting */
+	WMI_10X_VDEV_PARAM_FIXED_RATE,
+	/* Short GI Enable/Disable */
+	WMI_10X_VDEV_PARAM_SGI,
+	/* Enable LDPC */
+	WMI_10X_VDEV_PARAM_LDPC,
+	/* Enable Tx STBC */
+	WMI_10X_VDEV_PARAM_TX_STBC,
+	/* Enable Rx STBC */
+	WMI_10X_VDEV_PARAM_RX_STBC,
+	/* Intra BSS forwarding  */
+	WMI_10X_VDEV_PARAM_INTRA_BSS_FWD,
+	/* Setting Default xmit key for Vdev */
+	WMI_10X_VDEV_PARAM_DEF_KEYID,
+	/* NSS width */
+	WMI_10X_VDEV_PARAM_NSS,
+	/* Set the custom rate for the broadcast data frames */
+	WMI_10X_VDEV_PARAM_BCAST_DATA_RATE,
+	/* Set the custom rate (rate-code) for multicast data frames */
+	WMI_10X_VDEV_PARAM_MCAST_DATA_RATE,
+	/* Tx multicast packet indicate Enable/Disable */
+	WMI_10X_VDEV_PARAM_MCAST_INDICATE,
+	/* Tx DHCP packet indicate Enable/Disable */
+	WMI_10X_VDEV_PARAM_DHCP_INDICATE,
+	/* Enable host inspection of Tx unicast packet to unknown destination */
+	WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
+
+	/* The minimum amount of time AP begins to consider STA inactive */
+	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
+
+	/*
+	 * An associated STA is considered inactive when there is no recent
+	 * TX/RX activity and no downlink frames are buffered for it. Once a
+	 * STA exceeds the maximum idle inactive time, the AP will send an
+	 * 802.11 data-null as a keep alive to verify the STA is still
+	 * associated. If the STA does ACK the data-null, or if the data-null
+	 * is buffered and the STA does not retrieve it, the STA will be
+	 * considered unresponsive
+	 * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
+	 */
+	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
+
+	/*
+	 * An associated STA is considered unresponsive if there is no recent
+	 * TX/RX activity and downlink frames are buffered for it. Once a STA
+	 * exceeds the maximum unresponsive time, the AP will send a
+	 * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. */
+	WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
+
+	/* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
+	WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS,
+
+	WMI_10X_VDEV_PARAM_MCAST2UCAST_SET,
+	/* Enable/Disable RTS-CTS */
+	WMI_10X_VDEV_PARAM_ENABLE_RTSCTS,
+
+	WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
+};
+
 /* slot time long */
 #define WMI_VDEV_SLOT_TIME_LONG		0x1
 /* slot time short */
@@ -3064,8 +4024,7 @@ int ath10k_wmi_pdev_suspend_target(struct ath10k *ar);
 int ath10k_wmi_pdev_resume_target(struct ath10k *ar);
 int ath10k_wmi_pdev_set_regdomain(struct ath10k *ar, u16 rd, u16 rd2g,
 				  u16 rd5g, u16 ctl2g, u16 ctl5g);
-int ath10k_wmi_pdev_set_param(struct ath10k *ar, enum wmi_pdev_param id,
-			      u32 value);
+int ath10k_wmi_pdev_set_param(struct ath10k *ar, u32 id, u32 value);
 int ath10k_wmi_cmd_init(struct ath10k *ar);
 int ath10k_wmi_start_scan(struct ath10k *ar, const struct wmi_start_scan_arg *);
 void ath10k_wmi_start_scan_init(struct ath10k *ar, struct wmi_start_scan_arg *);
@@ -3085,7 +4044,7 @@ int ath10k_wmi_vdev_up(struct ath10k *ar, u32 vdev_id, u32 aid,
 		       const u8 *bssid);
 int ath10k_wmi_vdev_down(struct ath10k *ar, u32 vdev_id);
 int ath10k_wmi_vdev_set_param(struct ath10k *ar, u32 vdev_id,
-			      enum wmi_vdev_param param_id, u32 param_value);
+			      u32 param_id, u32 param_value);
 int ath10k_wmi_vdev_install_key(struct ath10k *ar,
 				const struct wmi_vdev_install_key_arg *arg);
 int ath10k_wmi_peer_create(struct ath10k *ar, u32 vdev_id,
@@ -3115,5 +4074,6 @@ int ath10k_wmi_pdev_set_wmm_params(struct ath10k *ar,
 int ath10k_wmi_request_stats(struct ath10k *ar, enum wmi_stats_id stats_id);
 int ath10k_wmi_force_fw_hang(struct ath10k *ar,
 			     enum wmi_force_fw_hang_type type, u32 delay_ms);
+int ath10k_wmi_mgmt_tx(struct ath10k *ar, struct sk_buff *skb);
 
 #endif /* _WMI_H_ */