Merge branch 'master' of /home/davem/src/GIT/linux-2.6/

Conflicts:
	include/net/tcp.h

4 files changed, 7 insertions, 7 deletions

diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h
index b72338c9bde..952b3a21bbc 100644
--- a/drivers/net/wireless/ath/ath5k/base.h
+++ b/drivers/net/wireless/ath/ath5k/base.h
@@ -36,7 +36,7 @@
  */
 
 /*
- * Defintions for the Atheros Wireless LAN controller driver.
+ * Definitions for the Atheros Wireless LAN controller driver.
  */
 #ifndef _DEV_ATH_ATHVAR_H
 #define _DEV_ATH_ATHVAR_H
@@ -190,7 +190,7 @@ struct ath5k_softc {
 	struct ath5k_txq	*cabq;		/* content after beacon */
 
 	int 			power_level;	/* Requested tx power in dbm */
-	bool			assoc;		/* assocate state */
+	bool			assoc;		/* associate state */
 	bool			enable_beacon;	/* true if beacons are on */
 };
 
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index 79188526260..5d1c8677f18 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -1491,7 +1491,7 @@ ath5k_eeprom_read_target_rate_pwr_info(struct ath5k_hw *ah, unsigned int mode)
  * This info is used to calibrate the baseband power table. Imagine
  * that for each channel there is a power curve that's hw specific
  * (depends on amplifier etc) and we try to "correct" this curve using
- * offests we pass on to phy chip (baseband -> before amplifier) so that
+ * offsets we pass on to phy chip (baseband -> before amplifier) so that
  * it can use accurate power values when setting tx power (takes amplifier's
  * performance on each channel into account).
  *
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index bbfdcd5e7cb..72474c0ccaf 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah,
 
 /*
  * This code is used to optimize rf gain on different environments
- * (temprature mostly) based on feedback from a power detector.
+ * (temperature mostly) based on feedback from a power detector.
  *
  * It's only used on RF5111 and RF5112, later RF chips seem to have
  * auto adjustment on hw -notice they have a much smaller BANK 7 and
@@ -2746,7 +2746,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
 		/* Fill curves in reverse order
 		 * from lower power (max gain)
 		 * to higher power. Use curve -> idx
-		 * backmaping we did on eeprom init */
+		 * backmapping we did on eeprom init */
 		u8 idx = pdg_curve_to_idx[pdg];
 
 		/* Grab the needed curves by index */
@@ -2848,7 +2848,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
 	/* Now we have a set of curves for this
 	 * channel on tmpL (x range is table_max - table_min
 	 * and y values are tmpL[pdg][]) sorted in the same
-	 * order as EEPROM (because we've used the backmaping).
+	 * order as EEPROM (because we've used the backmapping).
 	 * So for RF5112 it's from higher power to lower power
 	 * and for RF2413 it's from lower power to higher power.
 	 * For RF5111 we only have one curve. */
diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index c915954d4d5..70fdb9d8db8 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -880,7 +880,7 @@ static bool ath_rc_update_per(struct ath_softc *sc,
 				 * Since this probe succeeded, we allow the next
 				 * probe twice as soon.  This allows the maxRate
 				 * to move up faster if the probes are
-				 * succesful.
+				 * successful.
 				 */
 				ath_rc_priv->probe_time =
 					now_msec - rate_table->probe_interval / 2;