iwlagn: clean up some 3945/4965 remnants

When the driver was split, a bunch of definitions
for the 3945 and 4965 devices stayed around, but
they're now useless so remove (some of) them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 185 deletions

diff --git a/drivers/net/wireless/iwlwifi/iwl-eeprom.h b/drivers/net/wireless/iwlwifi/iwl-eeprom.h
index 98aa8af0119..d0f858af30e 100644
--- a/drivers/net/wireless/iwlwifi/iwl-eeprom.h
+++ b/drivers/net/wireless/iwlwifi/iwl-eeprom.h
@@ -110,10 +110,6 @@ enum {
 };
 
 /* SKU Capabilities */
-/* 3945 only */
-#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE                (1 << 0)
-#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE                (1 << 1)
-
 /* 5000 and up */
 #define EEPROM_SKU_CAP_BAND_POS				(4)
 #define EEPROM_SKU_CAP_BAND_SELECTION	                \
@@ -168,28 +164,6 @@ struct iwl_eeprom_enhanced_txpwr {
 	s8 mimo3_max;
 } __packed;
 
-/* 3945 Specific */
-#define EEPROM_3945_EEPROM_VERSION	(0x2f)
-
-/* 4965 has two radio transmitters (and 3 radio receivers) */
-#define EEPROM_TX_POWER_TX_CHAINS      (2)
-
-/* 4965 has room for up to 8 sets of txpower calibration data */
-#define EEPROM_TX_POWER_BANDS          (8)
-
-/* 4965 factory calibration measures txpower gain settings for
- * each of 3 target output levels */
-#define EEPROM_TX_POWER_MEASUREMENTS   (3)
-
-/* 4965 Specific */
-/* 4965 driver does not work with txpower calibration version < 5 */
-#define EEPROM_4965_TX_POWER_VERSION    (5)
-#define EEPROM_4965_EEPROM_VERSION	(0x2f)
-#define EEPROM_4965_CALIB_VERSION_OFFSET       (2*0xB6) /* 2 bytes */
-#define EEPROM_4965_CALIB_TXPOWER_OFFSET       (2*0xE8) /* 48  bytes */
-#define EEPROM_4965_BOARD_REVISION             (2*0x4F) /* 2 bytes */
-#define EEPROM_4965_BOARD_PBA                  (2*0x56+1) /* 9 bytes */
-
 /* 5000 Specific */
 #define EEPROM_5000_TX_POWER_VERSION    (4)
 #define EEPROM_5000_EEPROM_VERSION	(0x11A)
@@ -282,90 +256,6 @@ struct iwl_eeprom_enhanced_txpwr {
 /* 2.4 GHz */
 extern const u8 iwl_eeprom_band_1[14];
 
-/*
- * factory calibration data for one txpower level, on one channel,
- * measured on one of the 2 tx chains (radio transmitter and associated
- * antenna).  EEPROM contains:
- *
- * 1)  Temperature (degrees Celsius) of device when measurement was made.
- *
- * 2)  Gain table index used to achieve the target measurement power.
- *     This refers to the "well-known" gain tables (see iwl-4965-hw.h).
- *
- * 3)  Actual measured output power, in half-dBm ("34" = 17 dBm).
- *
- * 4)  RF power amplifier detector level measurement (not used).
- */
-struct iwl_eeprom_calib_measure {
-	u8 temperature;		/* Device temperature (Celsius) */
-	u8 gain_idx;		/* Index into gain table */
-	u8 actual_pow;		/* Measured RF output power, half-dBm */
-	s8 pa_det;		/* Power amp detector level (not used) */
-} __packed;
-
-
-/*
- * measurement set for one channel.  EEPROM contains:
- *
- * 1)  Channel number measured
- *
- * 2)  Measurements for each of 3 power levels for each of 2 radio transmitters
- *     (a.k.a. "tx chains") (6 measurements altogether)
- */
-struct iwl_eeprom_calib_ch_info {
-	u8 ch_num;
-	struct iwl_eeprom_calib_measure
-		measurements[EEPROM_TX_POWER_TX_CHAINS]
-			[EEPROM_TX_POWER_MEASUREMENTS];
-} __packed;
-
-/*
- * txpower subband info.
- *
- * For each frequency subband, EEPROM contains the following:
- *
- * 1)  First and last channels within range of the subband.  "0" values
- *     indicate that this sample set is not being used.
- *
- * 2)  Sample measurement sets for 2 channels close to the range endpoints.
- */
-struct iwl_eeprom_calib_subband_info {
-	u8 ch_from;	/* channel number of lowest channel in subband */
-	u8 ch_to;	/* channel number of highest channel in subband */
-	struct iwl_eeprom_calib_ch_info ch1;
-	struct iwl_eeprom_calib_ch_info ch2;
-} __packed;
-
-
-/*
- * txpower calibration info.  EEPROM contains:
- *
- * 1)  Factory-measured saturation power levels (maximum levels at which
- *     tx power amplifier can output a signal without too much distortion).
- *     There is one level for 2.4 GHz band and one for 5 GHz band.  These
- *     values apply to all channels within each of the bands.
- *
- * 2)  Factory-measured power supply voltage level.  This is assumed to be
- *     constant (i.e. same value applies to all channels/bands) while the
- *     factory measurements are being made.
- *
- * 3)  Up to 8 sets of factory-measured txpower calibration values.
- *     These are for different frequency ranges, since txpower gain
- *     characteristics of the analog radio circuitry vary with frequency.
- *
- *     Not all sets need to be filled with data;
- *     struct iwl_eeprom_calib_subband_info contains range of channels
- *     (0 if unused) for each set of data.
- */
-struct iwl_eeprom_calib_info {
-	u8 saturation_power24;	/* half-dBm (e.g. "34" = 17 dBm) */
-	u8 saturation_power52;	/* half-dBm */
-	__le16 voltage;		/* signed */
-	struct iwl_eeprom_calib_subband_info
-		band_info[EEPROM_TX_POWER_BANDS];
-} __packed;
-
-
 #define ADDRESS_MSK                 0x0000FFFF
 #define INDIRECT_TYPE_MSK           0x000F0000
 #define INDIRECT_HOST               0x00010000
@@ -398,83 +288,8 @@ struct iwl_eeprom_calib_info {
 #define EEPROM_RF_CFG_TX_ANT_MSK(x) ((x >> 8)  & 0xF) /* bits 8-11  */
 #define EEPROM_RF_CFG_RX_ANT_MSK(x) ((x >> 12) & 0xF) /* bits 12-15 */
 
-#define EEPROM_3945_RF_CFG_TYPE_MAX  0x0
-#define EEPROM_4965_RF_CFG_TYPE_MAX  0x1
-
-/* Radio Config for 5000 and up */
-#define EEPROM_RF_CONFIG_TYPE_R3x3	0x0
-#define EEPROM_RF_CONFIG_TYPE_R2x2	0x1
-#define EEPROM_RF_CONFIG_TYPE_R1x2	0x2
 #define EEPROM_RF_CONFIG_TYPE_MAX	0x3
 
-/*
- * Per-channel regulatory data.
- *
- * Each channel that *might* be supported by iwl has a fixed location
- * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
- * txpower (MSB).
- *
- * Entries immediately below are for 20 MHz channel width.  HT40 (40 MHz)
- * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
- *
- * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
- */
-#define EEPROM_REGULATORY_SKU_ID            (2*0x60)    /* 4  bytes */
-#define EEPROM_REGULATORY_BAND_1            (2*0x62)	/* 2  bytes */
-#define EEPROM_REGULATORY_BAND_1_CHANNELS   (2*0x63)	/* 28 bytes */
-
-/*
- * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
- * 5.0 GHz channels 7, 8, 11, 12, 16
- * (4915-5080MHz) (none of these is ever supported)
- */
-#define EEPROM_REGULATORY_BAND_2            (2*0x71)	/* 2  bytes */
-#define EEPROM_REGULATORY_BAND_2_CHANNELS   (2*0x72)	/* 26 bytes */
-
-/*
- * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
- * (5170-5320MHz)
- */
-#define EEPROM_REGULATORY_BAND_3            (2*0x7F)	/* 2  bytes */
-#define EEPROM_REGULATORY_BAND_3_CHANNELS   (2*0x80)	/* 24 bytes */
-
-/*
- * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
- * (5500-5700MHz)
- */
-#define EEPROM_REGULATORY_BAND_4            (2*0x8C)	/* 2  bytes */
-#define EEPROM_REGULATORY_BAND_4_CHANNELS   (2*0x8D)	/* 22 bytes */
-
-/*
- * 5.7 GHz channels 145, 149, 153, 157, 161, 165
- * (5725-5825MHz)
- */
-#define EEPROM_REGULATORY_BAND_5            (2*0x98)	/* 2  bytes */
-#define EEPROM_REGULATORY_BAND_5_CHANNELS   (2*0x99)	/* 12 bytes */
-
-/*
- * 2.4 GHz HT40 channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
- *
- * The channel listed is the center of the lower 20 MHz half of the channel.
- * The overall center frequency is actually 2 channels (10 MHz) above that,
- * and the upper half of each HT40 channel is centered 4 channels (20 MHz) away
- * from the lower half; e.g. the upper half of HT40 channel 1 is channel 5,
- * and the overall HT40 channel width centers on channel 3.
- *
- * NOTE:  The RXON command uses 20 MHz channel numbers to specify the
- *        control channel to which to tune.  RXON also specifies whether the
- *        control channel is the upper or lower half of a HT40 channel.
- *
- * NOTE:  4965 does not support HT40 channels on 2.4 GHz.
- */
-#define EEPROM_4965_REGULATORY_BAND_24_HT40_CHANNELS (2*0xA0)	/* 14 bytes */
-
-/*
- * 5.2 GHz HT40 channels 36 (40), 44 (48), 52 (56), 60 (64),
- * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
- */
-#define EEPROM_4965_REGULATORY_BAND_52_HT40_CHANNELS (2*0xA8)	/* 22 bytes */
-
 #define EEPROM_REGULATORY_BAND_NO_HT40			(0)
 
 struct iwl_eeprom_ops {