wireless/wl12xx/wl1251: move TI WLAN modules to a common ti subdirectory

Move wl12xx and wl1251 modules into a new drivers/net/wireless/ti
directory.  Add a TI WLAN Kconfig option and Makefile to support this
change.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Cc: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 655 deletions

diff --git a/drivers/net/wireless/wl1251/reg.h b/drivers/net/wireless/wl1251/reg.h
deleted file mode 100644
index a5809019c5c..00000000000
--- a/drivers/net/wireless/wl1251/reg.h
+++ /dev/null
@@ -1,655 +0,0 @@
-/*
- * This file is part of wl12xx
- *
- * Copyright (c) 1998-2007 Texas Instruments Incorporated
- * Copyright (C) 2008 Nokia Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#ifndef __REG_H__
-#define __REG_H__
-
-#include <linux/bitops.h>
-
-#define REGISTERS_BASE 0x00300000
-#define DRPW_BASE      0x00310000
-
-#define REGISTERS_DOWN_SIZE 0x00008800
-#define REGISTERS_WORK_SIZE 0x0000b000
-
-#define HW_ACCESS_ELP_CTRL_REG_ADDR         0x1FFFC
-
-/* ELP register commands */
-#define ELPCTRL_WAKE_UP             0x1
-#define ELPCTRL_WAKE_UP_WLAN_READY  0x5
-#define ELPCTRL_SLEEP               0x0
-/* ELP WLAN_READY bit */
-#define ELPCTRL_WLAN_READY          0x2
-
-/* Device Configuration registers*/
-#define SOR_CFG                        (REGISTERS_BASE + 0x0800)
-#define ECPU_CTRL                      (REGISTERS_BASE + 0x0804)
-#define HI_CFG                         (REGISTERS_BASE + 0x0808)
-
-/* EEPROM registers */
-#define EE_START                       (REGISTERS_BASE + 0x080C)
-#define EE_CTL                         (REGISTERS_BASE + 0x2000)
-#define EE_DATA                        (REGISTERS_BASE + 0x2004)
-#define EE_ADDR                        (REGISTERS_BASE + 0x2008)
-
-#define EE_CTL_READ                   2
-
-#define CHIP_ID_B                      (REGISTERS_BASE + 0x5674)
-
-#define CHIP_ID_1251_PG10	           (0x7010101)
-#define CHIP_ID_1251_PG11	           (0x7020101)
-#define CHIP_ID_1251_PG12	           (0x7030101)
-
-#define ENABLE                         (REGISTERS_BASE + 0x5450)
-
-/* Power Management registers */
-#define ELP_CFG_MODE                   (REGISTERS_BASE + 0x5804)
-#define ELP_CMD                        (REGISTERS_BASE + 0x5808)
-#define PLL_CAL_TIME                   (REGISTERS_BASE + 0x5810)
-#define CLK_REQ_TIME                   (REGISTERS_BASE + 0x5814)
-#define CLK_BUF_TIME                   (REGISTERS_BASE + 0x5818)
-
-#define CFG_PLL_SYNC_CNT               (REGISTERS_BASE + 0x5820)
-
-/* Scratch Pad registers*/
-#define SCR_PAD0                       (REGISTERS_BASE + 0x5608)
-#define SCR_PAD1                       (REGISTERS_BASE + 0x560C)
-#define SCR_PAD2                       (REGISTERS_BASE + 0x5610)
-#define SCR_PAD3                       (REGISTERS_BASE + 0x5614)
-#define SCR_PAD4                       (REGISTERS_BASE + 0x5618)
-#define SCR_PAD4_SET                   (REGISTERS_BASE + 0x561C)
-#define SCR_PAD4_CLR                   (REGISTERS_BASE + 0x5620)
-#define SCR_PAD5                       (REGISTERS_BASE + 0x5624)
-#define SCR_PAD5_SET                   (REGISTERS_BASE + 0x5628)
-#define SCR_PAD5_CLR                   (REGISTERS_BASE + 0x562C)
-#define SCR_PAD6                       (REGISTERS_BASE + 0x5630)
-#define SCR_PAD7                       (REGISTERS_BASE + 0x5634)
-#define SCR_PAD8                       (REGISTERS_BASE + 0x5638)
-#define SCR_PAD9                       (REGISTERS_BASE + 0x563C)
-
-/* Spare registers*/
-#define SPARE_A1                       (REGISTERS_BASE + 0x0994)
-#define SPARE_A2                       (REGISTERS_BASE + 0x0998)
-#define SPARE_A3                       (REGISTERS_BASE + 0x099C)
-#define SPARE_A4                       (REGISTERS_BASE + 0x09A0)
-#define SPARE_A5                       (REGISTERS_BASE + 0x09A4)
-#define SPARE_A6                       (REGISTERS_BASE + 0x09A8)
-#define SPARE_A7                       (REGISTERS_BASE + 0x09AC)
-#define SPARE_A8                       (REGISTERS_BASE + 0x09B0)
-#define SPARE_B1                       (REGISTERS_BASE + 0x5420)
-#define SPARE_B2                       (REGISTERS_BASE + 0x5424)
-#define SPARE_B3                       (REGISTERS_BASE + 0x5428)
-#define SPARE_B4                       (REGISTERS_BASE + 0x542C)
-#define SPARE_B5                       (REGISTERS_BASE + 0x5430)
-#define SPARE_B6                       (REGISTERS_BASE + 0x5434)
-#define SPARE_B7                       (REGISTERS_BASE + 0x5438)
-#define SPARE_B8                       (REGISTERS_BASE + 0x543C)
-
-enum wl12xx_acx_int_reg {
-	ACX_REG_INTERRUPT_TRIG,
-	ACX_REG_INTERRUPT_TRIG_H,
-
-/*=============================================
-  Host Interrupt Mask Register - 32bit (RW)
-  ------------------------------------------
-  Setting a bit in this register masks the
-  corresponding interrupt to the host.
-  0 - RX0		- Rx first dubble buffer Data Interrupt
-  1 - TXD		- Tx Data Interrupt
-  2 - TXXFR		- Tx Transfer Interrupt
-  3 - RX1		- Rx second dubble buffer Data Interrupt
-  4 - RXXFR		- Rx Transfer Interrupt
-  5 - EVENT_A	- Event Mailbox interrupt
-  6 - EVENT_B	- Event Mailbox interrupt
-  7 - WNONHST	- Wake On Host Interrupt
-  8 - TRACE_A	- Debug Trace interrupt
-  9 - TRACE_B	- Debug Trace interrupt
- 10 - CDCMP		- Command Complete Interrupt
- 11 -
- 12 -
- 13 -
- 14 - ICOMP		- Initialization Complete Interrupt
- 16 - SG SE		- Soft Gemini - Sense enable interrupt
- 17 - SG SD		- Soft Gemini - Sense disable interrupt
- 18 -			-
- 19 -			-
- 20 -			-
- 21-			-
- Default: 0x0001
-*==============================================*/
-	ACX_REG_INTERRUPT_MASK,
-
-/*=============================================
-  Host Interrupt Mask Set 16bit, (Write only)
-  ------------------------------------------
- Setting a bit in this register sets
- the corresponding bin in ACX_HINT_MASK register
- without effecting the mask
- state of other bits (0 = no effect).
-==============================================*/
-	ACX_REG_HINT_MASK_SET,
-
-/*=============================================
-  Host Interrupt Mask Clear 16bit,(Write only)
-  ------------------------------------------
- Setting a bit in this register clears
- the corresponding bin in ACX_HINT_MASK register
- without effecting the mask
- state of other bits (0 = no effect).
-=============================================*/
-	ACX_REG_HINT_MASK_CLR,
-
-/*=============================================
-  Host Interrupt Status Nondestructive Read
-  16bit,(Read only)
-  ------------------------------------------
- The host can read this register to determine
- which interrupts are active.
- Reading this register doesn't
- effect its content.
-=============================================*/
-	ACX_REG_INTERRUPT_NO_CLEAR,
-
-/*=============================================
-  Host Interrupt Status Clear on Read  Register
-  16bit,(Read only)
-  ------------------------------------------
- The host can read this register to determine
- which interrupts are active.
- Reading this register clears it,
- thus making all interrupts inactive.
-==============================================*/
-	ACX_REG_INTERRUPT_CLEAR,
-
-/*=============================================
-  Host Interrupt Acknowledge Register
-  16bit,(Write only)
-  ------------------------------------------
- The host can set individual bits in this
- register to clear (acknowledge) the corresp.
- interrupt status bits in the HINT_STS_CLR and
- HINT_STS_ND registers, thus making the
- assotiated interrupt inactive. (0-no effect)
-==============================================*/
-	ACX_REG_INTERRUPT_ACK,
-
-/*===============================================
-   Host Software Reset - 32bit RW
- ------------------------------------------
-    [31:1] Reserved
-    0  SOFT_RESET Soft Reset  - When this bit is set,
-    it holds the Wlan hardware in a soft reset state.
-    This reset disables all MAC and baseband processor
-    clocks except the CardBus/PCI interface clock.
-    It also initializes all MAC state machines except
-    the host interface. It does not reload the
-    contents of the EEPROM. When this bit is cleared
-    (not self-clearing), the Wlan hardware
-    exits the software reset state.
-===============================================*/
-	ACX_REG_SLV_SOFT_RESET,
-
-/*===============================================
- EEPROM Burst Read Start  - 32bit RW
- ------------------------------------------
- [31:1] Reserved
- 0  ACX_EE_START -  EEPROM Burst Read Start 0
- Setting this bit starts a burst read from
- the external EEPROM.
- If this bit is set (after reset) before an EEPROM read/write,
- the burst read starts at EEPROM address 0.
- Otherwise, it starts at the address
- following the address of the previous access.
- TheWlan hardware hardware clears this bit automatically.
-
- Default: 0x00000000
-*================================================*/
-	ACX_REG_EE_START,
-
-/* Embedded ARM CPU Control */
-
-/*===============================================
- Halt eCPU   - 32bit RW
- ------------------------------------------
- 0 HALT_ECPU Halt Embedded CPU - This bit is the
- compliment of bit 1 (MDATA2) in the SOR_CFG register.
- During a hardware reset, this bit holds
- the inverse of MDATA2.
- When downloading firmware from the host,
- set this bit (pull down MDATA2).
- The host clears this bit after downloading the firmware into
- zero-wait-state SSRAM.
- When loading firmware from Flash, clear this bit (pull up MDATA2)
- so that the eCPU can run the bootloader code in Flash
- HALT_ECPU eCPU State
- --------------------
- 1 halt eCPU
- 0 enable eCPU
- ===============================================*/
-	ACX_REG_ECPU_CONTROL,
-
-	ACX_REG_TABLE_LEN
-};
-
-#define ACX_SLV_SOFT_RESET_BIT   BIT(0)
-#define ACX_REG_EEPROM_START_BIT BIT(0)
-
-/* Command/Information Mailbox Pointers */
-
-/*===============================================
-  Command Mailbox Pointer - 32bit RW
- ------------------------------------------
- This register holds the start address of
- the command mailbox located in the Wlan hardware memory.
- The host must read this pointer after a reset to
- find the location of the command mailbox.
- The Wlan hardware initializes the command mailbox
- pointer with the default address of the command mailbox.
- The command mailbox pointer is not valid until after
- the host receives the Init Complete interrupt from
- the Wlan hardware.
- ===============================================*/
-#define REG_COMMAND_MAILBOX_PTR				(SCR_PAD0)
-
-/*===============================================
-  Information Mailbox Pointer - 32bit RW
- ------------------------------------------
- This register holds the start address of
- the information mailbox located in the Wlan hardware memory.
- The host must read this pointer after a reset to find
- the location of the information mailbox.
- The Wlan hardware initializes the information mailbox pointer
- with the default address of the information mailbox.
- The information mailbox pointer is not valid
- until after the host receives the Init Complete interrupt from
- the Wlan hardware.
- ===============================================*/
-#define REG_EVENT_MAILBOX_PTR				(SCR_PAD1)
-
-
-/* Misc */
-
-#define REG_ENABLE_TX_RX				(ENABLE)
-/*
- * Rx configuration (filter) information element
- * ---------------------------------------------
- */
-#define REG_RX_CONFIG				(RX_CFG)
-#define REG_RX_FILTER				(RX_FILTER_CFG)
-
-
-#define RX_CFG_ENABLE_PHY_HEADER_PLCP	 0x0002
-
-/* promiscuous - receives all valid frames */
-#define RX_CFG_PROMISCUOUS		 0x0008
-
-/* receives frames from any BSSID */
-#define RX_CFG_BSSID			 0x0020
-
-/* receives frames destined to any MAC address */
-#define RX_CFG_MAC			 0x0010
-
-#define RX_CFG_ENABLE_ONLY_MY_DEST_MAC	 0x0010
-#define RX_CFG_ENABLE_ANY_DEST_MAC	 0x0000
-#define RX_CFG_ENABLE_ONLY_MY_BSSID	 0x0020
-#define RX_CFG_ENABLE_ANY_BSSID		 0x0000
-
-/* discards all broadcast frames */
-#define RX_CFG_DISABLE_BCAST		 0x0200
-
-#define RX_CFG_ENABLE_ONLY_MY_SSID	 0x0400
-#define RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR 0x0800
-#define RX_CFG_COPY_RX_STATUS		 0x2000
-#define RX_CFG_TSF			 0x10000
-
-#define RX_CONFIG_OPTION_ANY_DST_MY_BSS	 (RX_CFG_ENABLE_ANY_DEST_MAC | \
-					  RX_CFG_ENABLE_ONLY_MY_BSSID)
-
-#define RX_CONFIG_OPTION_MY_DST_ANY_BSS	 (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
-					  | RX_CFG_ENABLE_ANY_BSSID)
-
-#define RX_CONFIG_OPTION_ANY_DST_ANY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
-					  RX_CFG_ENABLE_ANY_BSSID)
-
-#define RX_CONFIG_OPTION_MY_DST_MY_BSS	 (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
-					  | RX_CFG_ENABLE_ONLY_MY_BSSID)
-
-#define RX_CONFIG_OPTION_FOR_SCAN  (RX_CFG_ENABLE_PHY_HEADER_PLCP \
-				    | RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR \
-				    | RX_CFG_COPY_RX_STATUS | RX_CFG_TSF)
-
-#define RX_CONFIG_OPTION_FOR_MEASUREMENT (RX_CFG_ENABLE_ANY_DEST_MAC)
-
-#define RX_CONFIG_OPTION_FOR_JOIN	 (RX_CFG_ENABLE_ONLY_MY_BSSID | \
-					  RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
-
-#define RX_CONFIG_OPTION_FOR_IBSS_JOIN   (RX_CFG_ENABLE_ONLY_MY_SSID | \
-					  RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
-
-#define RX_FILTER_OPTION_DEF	      (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
-				       | CFG_RX_CTL_EN | CFG_RX_BCN_EN\
-				       | CFG_RX_AUTH_EN | CFG_RX_ASSOC_EN)
-
-#define RX_FILTER_OPTION_FILTER_ALL	 0
-
-#define RX_FILTER_OPTION_DEF_PRSP_BCN  (CFG_RX_PRSP_EN | CFG_RX_MGMT_EN\
-					| CFG_RX_RCTS_ACK | CFG_RX_BCN_EN)
-
-#define RX_FILTER_OPTION_JOIN	     (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
-				      | CFG_RX_BCN_EN | CFG_RX_AUTH_EN\
-				      | CFG_RX_ASSOC_EN | CFG_RX_RCTS_ACK\
-				      | CFG_RX_PRSP_EN)
-
-
-/*===============================================
- EEPROM Read/Write Request 32bit RW
- ------------------------------------------
- 1 EE_READ - EEPROM Read Request 1 - Setting this bit
- loads a single byte of data into the EE_DATA
- register from the EEPROM location specified in
- the EE_ADDR register.
- The Wlan hardware hardware clears this bit automatically.
- EE_DATA is valid when this bit is cleared.
-
- 0 EE_WRITE  - EEPROM Write Request  - Setting this bit
- writes a single byte of data from the EE_DATA register into the
- EEPROM location specified in the EE_ADDR register.
- The Wlan hardware hardware clears this bit automatically.
-*===============================================*/
-#define EE_CTL                              (REGISTERS_BASE + 0x2000)
-#define ACX_EE_CTL_REG                      EE_CTL
-#define EE_WRITE                            0x00000001ul
-#define EE_READ                             0x00000002ul
-
-/*===============================================
-  EEPROM Address  - 32bit RW
-  ------------------------------------------
-  This register specifies the address
-  within the EEPROM from/to which to read/write data.
-  ===============================================*/
-#define EE_ADDR                             (REGISTERS_BASE + 0x2008)
-#define ACX_EE_ADDR_REG                     EE_ADDR
-
-/*===============================================
-  EEPROM Data  - 32bit RW
-  ------------------------------------------
-  This register either holds the read 8 bits of
-  data from the EEPROM or the write data
-  to be written to the EEPROM.
-  ===============================================*/
-#define EE_DATA                             (REGISTERS_BASE + 0x2004)
-#define ACX_EE_DATA_REG                     EE_DATA
-
-#define EEPROM_ACCESS_TO                    10000   /* timeout counter */
-#define START_EEPROM_MGR                    0x00000001
-
-/*===============================================
-  EEPROM Base Address  - 32bit RW
-  ------------------------------------------
-  This register holds the upper nine bits
-  [23:15] of the 24-bit Wlan hardware memory
-  address for burst reads from EEPROM accesses.
-  The EEPROM provides the lower 15 bits of this address.
-  The MSB of the address from the EEPROM is ignored.
-  ===============================================*/
-#define ACX_EE_CFG                          EE_CFG
-
-/*===============================================
-  GPIO Output Values  -32bit, RW
-  ------------------------------------------
-  [31:16]  Reserved
-  [15: 0]  Specify the output values (at the output driver inputs) for
-  GPIO[15:0], respectively.
-  ===============================================*/
-#define ACX_GPIO_OUT_REG            GPIO_OUT
-#define ACX_MAX_GPIO_LINES          15
-
-/*===============================================
-  Contention window  -32bit, RW
-  ------------------------------------------
-  [31:26]  Reserved
-  [25:16]  Max (0x3ff)
-  [15:07]  Reserved
-  [06:00]  Current contention window value - default is 0x1F
-  ===============================================*/
-#define ACX_CONT_WIND_CFG_REG    CONT_WIND_CFG
-#define ACX_CONT_WIND_MIN_MASK   0x0000007f
-#define ACX_CONT_WIND_MAX        0x03ff0000
-
-/*===============================================
-  HI_CFG Interface Configuration Register Values
-  ------------------------------------------
-  ===============================================*/
-#define HI_CFG_UART_ENABLE          0x00000004
-#define HI_CFG_RST232_ENABLE        0x00000008
-#define HI_CFG_CLOCK_REQ_SELECT     0x00000010
-#define HI_CFG_HOST_INT_ENABLE      0x00000020
-#define HI_CFG_VLYNQ_OUTPUT_ENABLE  0x00000040
-#define HI_CFG_HOST_INT_ACTIVE_LOW  0x00000080
-#define HI_CFG_UART_TX_OUT_GPIO_15  0x00000100
-#define HI_CFG_UART_TX_OUT_GPIO_14  0x00000200
-#define HI_CFG_UART_TX_OUT_GPIO_7   0x00000400
-
-/*
- * NOTE: USE_ACTIVE_HIGH compilation flag should be defined in makefile
- *       for platforms using active high interrupt level
- */
-#ifdef USE_ACTIVE_HIGH
-#define HI_CFG_DEF_VAL              \
-	(HI_CFG_UART_ENABLE |        \
-	HI_CFG_RST232_ENABLE |      \
-	HI_CFG_CLOCK_REQ_SELECT |   \
-	HI_CFG_HOST_INT_ENABLE)
-#else
-#define HI_CFG_DEF_VAL              \
-	(HI_CFG_UART_ENABLE |        \
-	HI_CFG_RST232_ENABLE |      \
-	HI_CFG_CLOCK_REQ_SELECT |   \
-	HI_CFG_HOST_INT_ENABLE)
-
-#endif
-
-#define REF_FREQ_19_2                       0
-#define REF_FREQ_26_0                       1
-#define REF_FREQ_38_4                       2
-#define REF_FREQ_40_0                       3
-#define REF_FREQ_33_6                       4
-#define REF_FREQ_NUM                        5
-
-#define LUT_PARAM_INTEGER_DIVIDER           0
-#define LUT_PARAM_FRACTIONAL_DIVIDER        1
-#define LUT_PARAM_ATTN_BB                   2
-#define LUT_PARAM_ALPHA_BB                  3
-#define LUT_PARAM_STOP_TIME_BB              4
-#define LUT_PARAM_BB_PLL_LOOP_FILTER        5
-#define LUT_PARAM_NUM                       6
-
-#define ACX_EEPROMLESS_IND_REG              (SCR_PAD4)
-#define USE_EEPROM                          0
-#define SOFT_RESET_MAX_TIME                 1000000
-#define SOFT_RESET_STALL_TIME               1000
-#define NVS_DATA_BUNDARY_ALIGNMENT          4
-
-
-/* Firmware image load chunk size */
-#define CHUNK_SIZE          512
-
-/* Firmware image header size */
-#define FW_HDR_SIZE 8
-
-#define ECPU_CONTROL_HALT					0x00000101
-
-
-/******************************************************************************
-
-    CHANNELS, BAND & REG DOMAINS definitions
-
-******************************************************************************/
-
-
-enum {
-	RADIO_BAND_2_4GHZ = 0,  /* 2.4 Ghz band */
-	RADIO_BAND_5GHZ = 1,    /* 5 Ghz band */
-	RADIO_BAND_JAPAN_4_9_GHZ = 2,
-	DEFAULT_BAND = RADIO_BAND_2_4GHZ,
-	INVALID_BAND = 0xFE,
-	MAX_RADIO_BANDS = 0xFF
-};
-
-enum {
-	NO_RATE      = 0,
-	RATE_1MBPS   = 0x0A,
-	RATE_2MBPS   = 0x14,
-	RATE_5_5MBPS = 0x37,
-	RATE_6MBPS   = 0x0B,
-	RATE_9MBPS   = 0x0F,
-	RATE_11MBPS  = 0x6E,
-	RATE_12MBPS  = 0x0A,
-	RATE_18MBPS  = 0x0E,
-	RATE_22MBPS  = 0xDC,
-	RATE_24MBPS  = 0x09,
-	RATE_36MBPS  = 0x0D,
-	RATE_48MBPS  = 0x08,
-	RATE_54MBPS  = 0x0C
-};
-
-enum {
-	RATE_INDEX_1MBPS   =  0,
-	RATE_INDEX_2MBPS   =  1,
-	RATE_INDEX_5_5MBPS =  2,
-	RATE_INDEX_6MBPS   =  3,
-	RATE_INDEX_9MBPS   =  4,
-	RATE_INDEX_11MBPS  =  5,
-	RATE_INDEX_12MBPS  =  6,
-	RATE_INDEX_18MBPS  =  7,
-	RATE_INDEX_22MBPS  =  8,
-	RATE_INDEX_24MBPS  =  9,
-	RATE_INDEX_36MBPS  =  10,
-	RATE_INDEX_48MBPS  =  11,
-	RATE_INDEX_54MBPS  =  12,
-	RATE_INDEX_MAX     =  RATE_INDEX_54MBPS,
-	MAX_RATE_INDEX,
-	INVALID_RATE_INDEX = MAX_RATE_INDEX,
-	RATE_INDEX_ENUM_MAX_SIZE = 0x7FFFFFFF
-};
-
-enum {
-	RATE_MASK_1MBPS = 0x1,
-	RATE_MASK_2MBPS = 0x2,
-	RATE_MASK_5_5MBPS = 0x4,
-	RATE_MASK_11MBPS = 0x20,
-};
-
-#define SHORT_PREAMBLE_BIT   BIT(0) /* CCK or Barker depending on the rate */
-#define OFDM_RATE_BIT        BIT(6)
-#define PBCC_RATE_BIT        BIT(7)
-
-enum {
-	CCK_LONG = 0,
-	CCK_SHORT = SHORT_PREAMBLE_BIT,
-	PBCC_LONG = PBCC_RATE_BIT,
-	PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
-	OFDM = OFDM_RATE_BIT
-};
-
-/******************************************************************************
-
-Transmit-Descriptor RATE-SET field definitions...
-
-Define a new "Rate-Set" for TX path that incorporates the
-Rate & Modulation info into a single 16-bit field.
-
-TxdRateSet_t:
-b15   - Indicates Preamble type (1=SHORT, 0=LONG).
-	Notes:
-	Must be LONG (0) for 1Mbps rate.
-	Does not apply (set to 0) for RevG-OFDM rates.
-b14   - Indicates PBCC encoding (1=PBCC, 0=not).
-	Notes:
-	Does not apply (set to 0) for rates 1 and 2 Mbps.
-	Does not apply (set to 0) for RevG-OFDM rates.
-b13    - Unused (set to 0).
-b12-b0 - Supported Rate indicator bits as defined below.
-
-******************************************************************************/
-
-
-/*************************************************************************
-
-    Interrupt Trigger Register (Host -> WiLink)
-
-**************************************************************************/
-
-/* Hardware to Embedded CPU Interrupts - first 32-bit register set */
-
-/*
- * Host Command Interrupt. Setting this bit masks
- * the interrupt that the host issues to inform
- * the FW that it has sent a command
- * to the Wlan hardware Command Mailbox.
- */
-#define INTR_TRIG_CMD       BIT(0)
-
-/*
- * Host Event Acknowlegde Interrupt. The host
- * sets this bit to acknowledge that it received
- * the unsolicited information from the event
- * mailbox.
- */
-#define INTR_TRIG_EVENT_ACK BIT(1)
-
-/*
- * The host sets this bit to inform the Wlan
- * FW that a TX packet is in the XFER
- * Buffer #0.
- */
-#define INTR_TRIG_TX_PROC0 BIT(2)
-
-/*
- * The host sets this bit to inform the FW
- * that it read a packet from RX XFER
- * Buffer #0.
- */
-#define INTR_TRIG_RX_PROC0 BIT(3)
-
-#define INTR_TRIG_DEBUG_ACK BIT(4)
-
-#define INTR_TRIG_STATE_CHANGED BIT(5)
-
-
-/* Hardware to Embedded CPU Interrupts - second 32-bit register set */
-
-/*
- * The host sets this bit to inform the FW
- * that it read a packet from RX XFER
- * Buffer #1.
- */
-#define INTR_TRIG_RX_PROC1 BIT(17)
-
-/*
- * The host sets this bit to inform the Wlan
- * hardware that a TX packet is in the XFER
- * Buffer #1.
- */
-#define INTR_TRIG_TX_PROC1 BIT(18)
-
-#endif