Merge commit 'v2.6.37-rc7' into spi/next

10 files changed, 100 insertions, 60 deletions

diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
index f01e344cf4b..98e6fdf34d3 100644
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_MIPS) += setup-bus.o setup-irq.o
 obj-$(CONFIG_X86_VISWS) += setup-irq.o
 obj-$(CONFIG_MN10300) += setup-bus.o
 obj-$(CONFIG_MICROBLAZE) += setup-bus.o
+obj-$(CONFIG_TILE) += setup-bus.o setup-irq.o
 
 #
 # ACPI Related PCI FW Functions
diff --git a/drivers/pci/bus.c b/drivers/pci/bus.c
index 5624db8c9ad..69546e9213d 100644
--- a/drivers/pci/bus.c
+++ b/drivers/pci/bus.c
@@ -64,49 +64,6 @@ void pci_bus_remove_resources(struct pci_bus *bus)
 	}
 }
 
-/*
- * Find the highest-address bus resource below the cursor "res".  If the
- * cursor is NULL, return the highest resource.
- */
-static struct resource *pci_bus_find_resource_prev(struct pci_bus *bus,
-						   unsigned int type,
-						   struct resource *res)
-{
-	struct resource *r, *prev = NULL;
-	int i;
-
-	pci_bus_for_each_resource(bus, r, i) {
-		if (!r)
-			continue;
-
-		if ((r->flags & IORESOURCE_TYPE_BITS) != type)
-			continue;
-
-		/* If this resource is at or past the cursor, skip it */
-		if (res) {
-			if (r == res)
-				continue;
-			if (r->end > res->end)
-				continue;
-			if (r->end == res->end && r->start > res->start)
-				continue;
-		}
-
-		if (!prev)
-			prev = r;
-
-		/*
-		 * A small resource is higher than a large one that ends at
-		 * the same address.
-		 */
-		if (r->end > prev->end ||
-		    (r->end == prev->end && r->start > prev->start))
-			prev = r;
-	}
-
-	return prev;
-}
-
 /**
  * pci_bus_alloc_resource - allocate a resource from a parent bus
  * @bus: PCI bus
@@ -132,10 +89,9 @@ pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res,
 					  resource_size_t),
 		void *alignf_data)
 {
-	int ret = -ENOMEM;
+	int i, ret = -ENOMEM;
 	struct resource *r;
 	resource_size_t max = -1;
-	unsigned int type = res->flags & IORESOURCE_TYPE_BITS;
 
 	type_mask |= IORESOURCE_IO | IORESOURCE_MEM;
 
@@ -143,9 +99,10 @@ pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res,
 	if (!(res->flags & IORESOURCE_MEM_64))
 		max = PCIBIOS_MAX_MEM_32;
 
-	/* Look for space at highest addresses first */
-	r = pci_bus_find_resource_prev(bus, type, NULL);
-	for ( ; r; r = pci_bus_find_resource_prev(bus, type, r)) {
+	pci_bus_for_each_resource(bus, r, i) {
+		if (!r)
+			continue;
+
 		/* type_mask must match */
 		if ((res->flags ^ r->flags) & type_mask)
 			continue;
diff --git a/drivers/pci/dmar.c b/drivers/pci/dmar.c
index 0157708d474..09933eb9126 100644
--- a/drivers/pci/dmar.c
+++ b/drivers/pci/dmar.c
@@ -1417,6 +1417,11 @@ int __init enable_drhd_fault_handling(void)
 			       (unsigned long long)drhd->reg_base_addr, ret);
 			return -1;
 		}
+
+		/*
+		 * Clear any previous faults.
+		 */
+		dmar_fault(iommu->irq, iommu);
 	}
 
 	return 0;
diff --git a/drivers/pci/hotplug/ibmphp_ebda.c b/drivers/pci/hotplug/ibmphp_ebda.c
index 5becbdee402..2850e64deda 100644
--- a/drivers/pci/hotplug/ibmphp_ebda.c
+++ b/drivers/pci/hotplug/ibmphp_ebda.c
@@ -276,6 +276,12 @@ int __init ibmphp_access_ebda (void)
 
 	for (;;) {
 		offset = next_offset;
+
+		/* Make sure what we read is still in the mapped section */
+		if (WARN(offset > (ebda_sz * 1024 - 4),
+			 "ibmphp_ebda: next read is beyond ebda_sz\n"))
+			break;
+
 		next_offset = readw (io_mem + offset);	/* offset of next blk */
 
 		offset += 2;
diff --git a/drivers/pci/pci-sysfs.c b/drivers/pci/pci-sysfs.c
index b5a7d9bfcb2..63d5042f207 100644
--- a/drivers/pci/pci-sysfs.c
+++ b/drivers/pci/pci-sysfs.c
@@ -705,17 +705,21 @@ void pci_remove_legacy_files(struct pci_bus *b)
 
 #ifdef HAVE_PCI_MMAP
 
-int pci_mmap_fits(struct pci_dev *pdev, int resno, struct vm_area_struct *vma)
+int pci_mmap_fits(struct pci_dev *pdev, int resno, struct vm_area_struct *vma,
+		  enum pci_mmap_api mmap_api)
 {
-	unsigned long nr, start, size;
+	unsigned long nr, start, size, pci_start;
 
+	if (pci_resource_len(pdev, resno) == 0)
+		return 0;
 	nr = (vma->vm_end - vma->vm_start) >> PAGE_SHIFT;
 	start = vma->vm_pgoff;
 	size = ((pci_resource_len(pdev, resno) - 1) >> PAGE_SHIFT) + 1;
-	if (start < size && size - start >= nr)
+	pci_start = (mmap_api == PCI_MMAP_PROCFS) ?
+			pci_resource_start(pdev, resno) >> PAGE_SHIFT : 0;
+	if (start >= pci_start && start < pci_start + size &&
+			start + nr <= pci_start + size)
 		return 1;
-	WARN(1, "process \"%s\" tried to map 0x%08lx-0x%08lx on %s BAR %d (size 0x%08lx)\n",
-		current->comm, start, start+nr, pci_name(pdev), resno, size);
 	return 0;
 }
 
@@ -745,8 +749,15 @@ pci_mmap_resource(struct kobject *kobj, struct bin_attribute *attr,
 	if (i >= PCI_ROM_RESOURCE)
 		return -ENODEV;
 
-	if (!pci_mmap_fits(pdev, i, vma))
+	if (!pci_mmap_fits(pdev, i, vma, PCI_MMAP_SYSFS)) {
+		WARN(1, "process \"%s\" tried to map 0x%08lx bytes "
+			"at page 0x%08lx on %s BAR %d (start 0x%16Lx, size 0x%16Lx)\n",
+			current->comm, vma->vm_end-vma->vm_start, vma->vm_pgoff,
+			pci_name(pdev), i,
+			(u64)pci_resource_start(pdev, i),
+			(u64)pci_resource_len(pdev, i));
 		return -EINVAL;
+	}
 
 	/* pci_mmap_page_range() expects the same kind of entry as coming
 	 * from /proc/bus/pci/ which is a "user visible" value. If this is
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index e98c8104297..710c8a29be0 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1007,6 +1007,18 @@ static int __pci_enable_device_flags(struct pci_dev *dev,
 	int err;
 	int i, bars = 0;
 
+	/*
+	 * Power state could be unknown at this point, either due to a fresh
+	 * boot or a device removal call.  So get the current power state
+	 * so that things like MSI message writing will behave as expected
+	 * (e.g. if the device really is in D0 at enable time).
+	 */
+	if (dev->pm_cap) {
+		u16 pmcsr;
+		pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
+		dev->current_state = (pmcsr & PCI_PM_CTRL_STATE_MASK);
+	}
+
 	if (atomic_add_return(1, &dev->enable_cnt) > 1)
 		return 0;		/* already enabled */
 
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index f5c7c382765..7d33f667386 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -22,8 +22,13 @@ extern void pci_remove_firmware_label_files(struct pci_dev *pdev);
 #endif
 extern void pci_cleanup_rom(struct pci_dev *dev);
 #ifdef HAVE_PCI_MMAP
+enum pci_mmap_api {
+	PCI_MMAP_SYSFS,	/* mmap on /sys/bus/pci/devices/<BDF>/resource<N> */
+	PCI_MMAP_PROCFS	/* mmap on /proc/bus/pci/<BDF> */
+};
 extern int pci_mmap_fits(struct pci_dev *pdev, int resno,
-			 struct vm_area_struct *vma);
+			 struct vm_area_struct *vmai,
+			 enum pci_mmap_api mmap_api);
 #endif
 int pci_probe_reset_function(struct pci_dev *dev);
 
diff --git a/drivers/pci/proc.c b/drivers/pci/proc.c
index 297b72c880a..27911b55c2a 100644
--- a/drivers/pci/proc.c
+++ b/drivers/pci/proc.c
@@ -10,7 +10,6 @@
 #include <linux/module.h>
 #include <linux/proc_fs.h>
 #include <linux/seq_file.h>
-#include <linux/smp_lock.h>
 #include <linux/capability.h>
 #include <asm/uaccess.h>
 #include <asm/byteorder.h>
@@ -257,7 +256,7 @@ static int proc_bus_pci_mmap(struct file *file, struct vm_area_struct *vma)
 
 	/* Make sure the caller is mapping a real resource for this device */
 	for (i = 0; i < PCI_ROM_RESOURCE; i++) {
-		if (pci_mmap_fits(dev, i, vma))
+		if (pci_mmap_fits(dev, i, vma,  PCI_MMAP_PROCFS))
 			break;
 	}
 
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index f5c63fe9db5..53a786fd0d4 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -2136,6 +2136,24 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB,
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB,
 			quirk_unhide_mch_dev6);
 
+#ifdef CONFIG_TILE
+/*
+ * The Tilera TILEmpower platform needs to set the link speed
+ * to 2.5GT(Giga-Transfers)/s (Gen 1). The default link speed
+ * setting is 5GT/s (Gen 2). 0x98 is the Link Control2 PCIe
+ * capability register of the PEX8624 PCIe switch. The switch
+ * supports link speed auto negotiation, but falsely sets
+ * the link speed to 5GT/s.
+ */
+static void __devinit quirk_tile_plx_gen1(struct pci_dev *dev)
+{
+	if (tile_plx_gen1) {
+		pci_write_config_dword(dev, 0x98, 0x1);
+		mdelay(50);
+	}
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1);
+#endif /* CONFIG_TILE */
 
 #ifdef CONFIG_PCI_MSI
 /* Some chipsets do not support MSI. We cannot easily rely on setting
@@ -2311,6 +2329,9 @@ static void __devinit nvbridge_check_legacy_irq_routing(struct pci_dev *dev)
 {
 	u32 cfg;
 
+	if (!pci_find_capability(dev, PCI_CAP_ID_HT))
+		return;
+
 	pci_read_config_dword(dev, 0x74, &cfg);
 
 	if (cfg & ((1 << 2) | (1 << 15))) {
@@ -2746,6 +2767,29 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_m
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832);
 #endif /*CONFIG_MMC_RICOH_MMC*/
 
+#if defined(CONFIG_DMAR) || defined(CONFIG_INTR_REMAP)
+#define VTUNCERRMSK_REG	0x1ac
+#define VTD_MSK_SPEC_ERRORS	(1 << 31)
+/*
+ * This is a quirk for masking vt-d spec defined errors to platform error
+ * handling logic. With out this, platforms using Intel 7500, 5500 chipsets
+ * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based
+ * on the RAS config settings of the platform) when a vt-d fault happens.
+ * The resulting SMI caused the system to hang.
+ *
+ * VT-d spec related errors are already handled by the VT-d OS code, so no
+ * need to report the same error through other channels.
+ */
+static void vtd_mask_spec_errors(struct pci_dev *dev)
+{
+	u32 word;
+
+	pci_read_config_dword(dev, VTUNCERRMSK_REG, &word);
+	pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors);
+#endif
 
 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f,
 			  struct pci_fixup *end)
diff --git a/drivers/pci/xen-pcifront.c b/drivers/pci/xen-pcifront.c
index a87c4985326..3a5a6fcc0ea 100644
--- a/drivers/pci/xen-pcifront.c
+++ b/drivers/pci/xen-pcifront.c
@@ -13,7 +13,6 @@
 #include <linux/spinlock.h>
 #include <linux/pci.h>
 #include <linux/msi.h>
-#include <xen/xenbus.h>
 #include <xen/interface/io/pciif.h>
 #include <asm/xen/pci.h>
 #include <linux/interrupt.h>
@@ -576,8 +575,9 @@ static pci_ers_result_t pcifront_common_process(int cmd,
 
 	pcidev = pci_get_bus_and_slot(bus, devfn);
 	if (!pcidev || !pcidev->driver) {
-		dev_err(&pcidev->dev,
-			"device or driver is NULL\n");
+		dev_err(&pdev->xdev->dev, "device or AER driver is NULL\n");
+		if (pcidev)
+			pci_dev_put(pcidev);
 		return result;
 	}
 	pdrv = pcidev->driver;