Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree conversions and enablement from Olof Johansson:
 "Continued device tree conversion and enablement across a number of
  platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
  smaller series as well.

  ux500 has seen continued conversion for platforms.  Several platforms
  have seen pinctrl-via-devicetree conversions for simpler
  multiplatform.  Tegra is adding data for new devices/drivers, and
  Exynos has a bunch of new bindings and devices added as well.

  So, pretty much the same progression in the right direction as the
  last few releases."

Fix up conflicts as per Olof.

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
  ARM: ux500: Rename dbx500 cpufreq code to be more generic
  ARM: dts: add missing ux500 device trees
  ARM: ux500: Stop registering the PCM driver from platform code
  ARM: ux500: Move board specific GPIO info out to subordinate DTS files
  ARM: ux500: Disable the MMCI gpio-regulator by default
  ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
  ARM: Kirkwood: Add support LED of OpenBlocks A6
  ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
  ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
  ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
  ARM: kirkwood: Add support DT of second I2C bus
  ARM: kirkwood: Convert mplcec4 board to pinctrl
  ARM: Kirkwood: Convert km_kirkwood to pinctrl
  ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
  ARM: Kirkwood: Convert IX2-200 to pinctrl.
  ARM: Kirkwood: Convert lsxl boards to pinctrl.
  ARM: Kirkwood: Convert ib62x0 to pinctrl.
  ARM: Kirkwood: Convert GoFlex Net to pinctrl.
  ARM: Kirkwood: Convert dreamplug to pinctrl.
  ARM: Kirkwood: Convert dockstar to pinctrl.
  ...

5 files changed, 149 insertions, 0 deletions

diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 49a89397231..b1d956d81f0 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -335,6 +335,9 @@ config AB8500_BATTERY_THERM_ON_BATCTRL
 	help
 	  Say Y to enable battery temperature measurements using
 	  thermistor connected on BATCTRL ADC.
+
+source "drivers/power/reset/Kconfig"
+
 endif # POWER_SUPPLY
 
 source "drivers/power/avs/Kconfig"
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b949cf85590..f1d99f4a0bc 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -49,3 +49,4 @@ obj-$(CONFIG_CHARGER_MAX8997)	+= max8997_charger.o
 obj-$(CONFIG_CHARGER_MAX8998)	+= max8998_charger.o
 obj-$(CONFIG_POWER_AVS)		+= avs/
 obj-$(CONFIG_CHARGER_SMB347)	+= smb347-charger.o
+obj-$(CONFIG_POWER_RESET)	+= reset/
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
new file mode 100644
index 00000000000..6461b489fb0
--- /dev/null
+++ b/drivers/power/reset/Kconfig
@@ -0,0 +1,15 @@
+menuconfig POWER_RESET
+	bool "Board level reset or power off"
+	help
+	  Provides a number of drivers which either reset a complete board
+	  or shut it down, by manipulating the main power supply on the board.
+
+	  Say Y here to enable board reset and power off
+
+config POWER_RESET_GPIO
+	bool "GPIO power-off driver"
+	depends on OF_GPIO && POWER_RESET
+	help
+	  This driver supports turning off your board via a GPIO line.
+	  If your board needs a GPIO high/low to power down, say Y and
+	  create a binding in your devicetree.
diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
new file mode 100644
index 00000000000..751488a4a0c
--- /dev/null
+++ b/drivers/power/reset/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
diff --git a/drivers/power/reset/gpio-poweroff.c b/drivers/power/reset/gpio-poweroff.c
new file mode 100644
index 00000000000..0491e5335d0
--- /dev/null
+++ b/drivers/power/reset/gpio-poweroff.c
@@ -0,0 +1,129 @@
+/*
+ * Toggles a GPIO pin to power down a device
+ *
+ * Jamie Lentin <jm@lentin.co.uk>
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * Copyright (C) 2012 Jamie Lentin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/module.h>
+
+/*
+ * Hold configuration here, cannot be more than one instance of the driver
+ * since pm_power_off itself is global.
+ */
+static int gpio_num = -1;
+static int gpio_active_low;
+
+static void gpio_poweroff_do_poweroff(void)
+{
+	BUG_ON(gpio_num == -1);
+
+	/* drive it active */
+	gpio_direction_output(gpio_num, !gpio_active_low);
+	mdelay(100);
+	/* rising edge or drive inactive */
+	gpio_set_value(gpio_num, gpio_active_low);
+	mdelay(100);
+	/* falling edge */
+	gpio_set_value(gpio_num, !gpio_active_low);
+
+	/* give it some time */
+	mdelay(3000);
+
+	WARN_ON(1);
+}
+
+static int __devinit gpio_poweroff_probe(struct platform_device *pdev)
+{
+	enum of_gpio_flags flags;
+	bool input = false;
+	int ret;
+
+	/* If a pm_power_off function has already been added, leave it alone */
+	if (pm_power_off != NULL) {
+		pr_err("%s: pm_power_off function already registered",
+		       __func__);
+		return -EBUSY;
+	}
+
+	gpio_num = of_get_gpio_flags(pdev->dev.of_node, 0, &flags);
+	if (gpio_num < 0) {
+		pr_err("%s: Could not get GPIO configuration: %d",
+		       __func__, gpio_num);
+		return -ENODEV;
+	}
+	gpio_active_low = flags & OF_GPIO_ACTIVE_LOW;
+
+	if (of_get_property(pdev->dev.of_node, "input", NULL))
+		input = true;
+
+	ret = gpio_request(gpio_num, "poweroff-gpio");
+	if (ret) {
+		pr_err("%s: Could not get GPIO %d", __func__, gpio_num);
+		return ret;
+	}
+	if (input) {
+		if (gpio_direction_input(gpio_num)) {
+			pr_err("Could not set direction of GPIO %d to input",
+			       gpio_num);
+			goto err;
+		}
+	} else {
+		if (gpio_direction_output(gpio_num, gpio_active_low)) {
+			pr_err("Could not set direction of GPIO %d", gpio_num);
+			goto err;
+		}
+	}
+
+	pm_power_off = &gpio_poweroff_do_poweroff;
+	return 0;
+
+err:
+	gpio_free(gpio_num);
+	return -ENODEV;
+}
+
+static int __devexit gpio_poweroff_remove(struct platform_device *pdev)
+{
+	if (gpio_num != -1)
+		gpio_free(gpio_num);
+	if (pm_power_off == &gpio_poweroff_do_poweroff)
+		pm_power_off = NULL;
+
+	return 0;
+}
+
+static const struct of_device_id of_gpio_poweroff_match[] = {
+	{ .compatible = "gpio-poweroff", },
+	{},
+};
+
+static struct platform_driver gpio_poweroff_driver = {
+	.probe = gpio_poweroff_probe,
+	.remove = __devexit_p(gpio_poweroff_remove),
+	.driver = {
+		   .name = "poweroff-gpio",
+		   .owner = THIS_MODULE,
+		   .of_match_table = of_gpio_poweroff_match,
+		   },
+};
+
+module_platform_driver(gpio_poweroff_driver);
+
+MODULE_AUTHOR("Jamie Lentin <jm@lentin.co.uk>");
+MODULE_DESCRIPTION("GPIO poweroff driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:poweroff-gpio");