pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2

The i.MX PWM version2 is embedded in several i.MX SoCs, such as i.MX27,
i.MX51 and i.MX6SL.  There is a 4-word (16 bit) sample FIFO in this IP.
Each FIFO slot determines the duty period of a PWM waveform in one full
cycle.  The IP spec mentions that we should not write a fourth sample
because the FIFO will become full and triggers a FIFO write error (FWE)
which will prevent the PWM from starting once it is enabled.  In order
to avoid any sample FIFO overflow issue, this patch clears all sample
FIFO by doing software reset in the configuration hook when the
controller is disabled or waits for a full PWM cycle to get a
relinquished FIFO slot when the controller is enabled and the FIFO is
fully loaded.

The FIFO overflow issue can be reproduced by the following commands on
the i.MX6SL EVK platform, assuming we use PWM2 for the debug LED which
is driven by the pin HSIC_STROBE and the maximal brightness is 255.

	echo 0   > /sys/class/leds/user/brightness
	echo 0   > /sys/class/leds/user/brightness
	echo 0   > /sys/class/leds/user/brightness
	echo 0   > /sys/class/leds/user/brightness
	echo 255 > /sys/class/leds/user/brightness

Here, FWE happens (PWMSR register reads 0x58) and the LED can not be
lighten.

Another way to reproduce the FIFO overflow issue is to run this script:

	while true;
		do echo 255 > /sys/class/leds/user/brightness;
	done

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: linux-pwm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

1 files changed, 43 insertions, 2 deletions

diff --git a/drivers/pwm/pwm-imx.c b/drivers/pwm/pwm-imx.c
index fb68534b098..f8b5f109c1a 100644
--- a/drivers/pwm/pwm-imx.c
+++ b/drivers/pwm/pwm-imx.c
@@ -14,6 +14,7 @@
 #include <linux/slab.h>
 #include <linux/err.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/pwm.h>
 #include <linux/of.h>
@@ -30,6 +31,7 @@
 /* i.MX27, i.MX31, i.MX35 share the same PWM function block: */
 
 #define MX3_PWMCR			0x00    /* PWM Control Register */
+#define MX3_PWMSR			0x04    /* PWM Status Register */
 #define MX3_PWMSAR			0x0C    /* PWM Sample Register */
 #define MX3_PWMPR			0x10    /* PWM Period Register */
 #define MX3_PWMCR_PRESCALER(x)		((((x) - 1) & 0xFFF) << 4)
@@ -38,7 +40,12 @@
 #define MX3_PWMCR_DBGEN			(1 << 22)
 #define MX3_PWMCR_CLKSRC_IPG_HIGH	(2 << 16)
 #define MX3_PWMCR_CLKSRC_IPG		(1 << 16)
+#define MX3_PWMCR_SWR			(1 << 3)
 #define MX3_PWMCR_EN			(1 << 0)
+#define MX3_PWMSR_FIFOAV_4WORDS		0x4
+#define MX3_PWMSR_FIFOAV_MASK		0x7
+
+#define MX3_PWM_SWR_LOOP		5
 
 struct imx_chip {
 	struct clk	*clk_per;
@@ -103,9 +110,43 @@ static int imx_pwm_config_v2(struct pwm_chip *chip,
 		struct pwm_device *pwm, int duty_ns, int period_ns)
 {
 	struct imx_chip *imx = to_imx_chip(chip);
+	struct device *dev = chip->dev;
 	unsigned long long c;
 	unsigned long period_cycles, duty_cycles, prescale;
-	u32 cr;
+	unsigned int period_ms;
+	bool enable = test_bit(PWMF_ENABLED, &pwm->flags);
+	int wait_count = 0, fifoav;
+	u32 cr, sr;
+
+	/*
+	 * i.MX PWMv2 has a 4-word sample FIFO.
+	 * In order to avoid FIFO overflow issue, we do software reset
+	 * to clear all sample FIFO if the controller is disabled or
+	 * wait for a full PWM cycle to get a relinquished FIFO slot
+	 * when the controller is enabled and the FIFO is fully loaded.
+	 */
+	if (enable) {
+		sr = readl(imx->mmio_base + MX3_PWMSR);
+		fifoav = sr & MX3_PWMSR_FIFOAV_MASK;
+		if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+			period_ms = DIV_ROUND_UP(pwm->period, NSEC_PER_MSEC);
+			msleep(period_ms);
+
+			sr = readl(imx->mmio_base + MX3_PWMSR);
+			if (fifoav == (sr & MX3_PWMSR_FIFOAV_MASK))
+				dev_warn(dev, "there is no free FIFO slot\n");
+		}
+	} else {
+		writel(MX3_PWMCR_SWR, imx->mmio_base + MX3_PWMCR);
+		do {
+			usleep_range(200, 1000);
+			cr = readl(imx->mmio_base + MX3_PWMCR);
+		} while ((cr & MX3_PWMCR_SWR) &&
+			 (wait_count++ < MX3_PWM_SWR_LOOP));
+
+		if (cr & MX3_PWMCR_SWR)
+			dev_warn(dev, "software reset timeout\n");
+	}
 
 	c = clk_get_rate(imx->clk_per);
 	c = c * period_ns;
@@ -135,7 +176,7 @@ static int imx_pwm_config_v2(struct pwm_chip *chip,
 		MX3_PWMCR_DOZEEN | MX3_PWMCR_WAITEN |
 		MX3_PWMCR_DBGEN | MX3_PWMCR_CLKSRC_IPG_HIGH;
 
-	if (test_bit(PWMF_ENABLED, &pwm->flags))
+	if (enable)
 		cr |= MX3_PWMCR_EN;
 
 	writel(cr, imx->mmio_base + MX3_PWMCR);