[SCSI] aiclib remove dead

remove lots of completely dead code from aiclib, there's not a lot left
and even what's left is rather useless.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

1 files changed, 0 insertions, 868 deletions

diff --git a/drivers/scsi/aic7xxx/aiclib.h b/drivers/scsi/aic7xxx/aiclib.h
index bfe6f954d3c..e7d94cbaf2a 100644
--- a/drivers/scsi/aic7xxx/aiclib.h
+++ b/drivers/scsi/aic7xxx/aiclib.h
@@ -57,121 +57,6 @@
 #ifndef	_AICLIB_H
 #define _AICLIB_H
 
-/*
- * Linux Interrupt Support.
- */
-#ifndef IRQ_RETVAL
-typedef void irqreturn_t;
-#define	IRQ_RETVAL(x)
-#endif
-
-/*
- * SCSI command format
- */
-
-/*
- * Define dome bits that are in ALL (or a lot of) scsi commands
- */
-#define SCSI_CTL_LINK		0x01
-#define SCSI_CTL_FLAG		0x02
-#define SCSI_CTL_VENDOR		0xC0
-#define	SCSI_CMD_LUN		0xA0	/* these two should not be needed */
-#define	SCSI_CMD_LUN_SHIFT	5	/* LUN in the cmd is no longer SCSI */
-
-#define SCSI_MAX_CDBLEN		16	/* 
-					 * 16 byte commands are in the 
-					 * SCSI-3 spec 
-					 */
-/* 6byte CDBs special case 0 length to be 256 */
-#define SCSI_CDB6_LEN(len)	((len) == 0 ? 256 : len)
-
-/*
- * This type defines actions to be taken when a particular sense code is
- * received.  Right now, these flags are only defined to take up 16 bits,
- * but can be expanded in the future if necessary.
- */
-typedef enum {
-	SS_NOP		= 0x000000, /* Do nothing */
-	SS_RETRY	= 0x010000, /* Retry the command */
-	SS_FAIL		= 0x020000, /* Bail out */
-	SS_START	= 0x030000, /* Send a Start Unit command to the device,
-				     * then retry the original command.
-				     */
-	SS_TUR		= 0x040000, /* Send a Test Unit Ready command to the
-				     * device, then retry the original command.
-				     */
-	SS_REQSENSE	= 0x050000, /* Send a RequestSense command to the
-				     * device, then retry the original command.
-				     */
-	SS_INQ_REFRESH	= 0x060000,
-	SS_MASK		= 0xff0000
-} aic_sense_action;
-
-typedef enum {
-	SSQ_NONE		= 0x0000,
-	SSQ_DECREMENT_COUNT	= 0x0100,  /* Decrement the retry count */
-	SSQ_MANY		= 0x0200,  /* send lots of recovery commands */
-	SSQ_RANGE		= 0x0400,  /*
-					    * This table entry represents the
-					    * end of a range of ASCQs that
-					    * have identical error actions
-					    * and text.
-					    */
-	SSQ_PRINT_SENSE		= 0x0800,
-	SSQ_DELAY		= 0x1000,  /* Delay before retry. */
-	SSQ_DELAY_RANDOM	= 0x2000,  /* Randomized delay before retry. */
-	SSQ_FALLBACK		= 0x4000,  /* Do a speed fallback to recover */
-	SSQ_MASK		= 0xff00
-} aic_sense_action_qualifier;
-
-/* Mask for error status values */
-#define SS_ERRMASK	0xff
-
-/* The default, retyable, error action */
-#define SS_RDEF		SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE|EIO
-
-/* The retyable, error action, with table specified error code */
-#define SS_RET		SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE
-
-/* Fatal error action, with table specified error code */
-#define SS_FATAL	SS_FAIL|SSQ_PRINT_SENSE
-
-struct scsi_generic
-{
-	uint8_t opcode;
-	uint8_t bytes[11];
-};
-
-struct scsi_request_sense
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[2];
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_test_unit_ready
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[3];
-	uint8_t control;
-};
-
-struct scsi_send_diag
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SSD_UOL		0x01
-#define	SSD_DOL		0x02
-#define	SSD_SELFTEST	0x04
-#define	SSD_PF		0x10
-	uint8_t unused[1];
-	uint8_t paramlen[2];
-	uint8_t control;
-};
-
 struct scsi_sense
 {
 	uint8_t opcode;
@@ -181,537 +66,12 @@ struct scsi_sense
 	uint8_t control;
 };
 
-struct scsi_inquiry
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SI_EVPD 0x01
-	uint8_t page_code;
-	uint8_t reserved;
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_mode_sense_6
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SMS_DBD				0x08
-	uint8_t page;
-#define	SMS_PAGE_CODE 			0x3F
-#define SMS_VENDOR_SPECIFIC_PAGE	0x00
-#define SMS_DISCONNECT_RECONNECT_PAGE	0x02
-#define SMS_PERIPHERAL_DEVICE_PAGE	0x09
-#define SMS_CONTROL_MODE_PAGE		0x0A
-#define SMS_ALL_PAGES_PAGE		0x3F
-#define	SMS_PAGE_CTRL_MASK		0xC0
-#define	SMS_PAGE_CTRL_CURRENT 		0x00
-#define	SMS_PAGE_CTRL_CHANGEABLE 	0x40
-#define	SMS_PAGE_CTRL_DEFAULT 		0x80
-#define	SMS_PAGE_CTRL_SAVED 		0xC0
-	uint8_t unused;
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_mode_sense_10
-{
-	uint8_t opcode;
-	uint8_t byte2;		/* same bits as small version */
-	uint8_t page; 		/* same bits as small version */
-	uint8_t unused[4];
-	uint8_t length[2];
-	uint8_t control;
-};
-
-struct scsi_mode_select_6
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SMS_SP	0x01
-#define	SMS_PF	0x10
-	uint8_t unused[2];
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_mode_select_10
-{
-	uint8_t opcode;
-	uint8_t byte2;		/* same bits as small version */
-	uint8_t unused[5];
-	uint8_t length[2];
-	uint8_t control;
-};
-
-/*
- * When sending a mode select to a tape drive, the medium type must be 0.
- */
-struct scsi_mode_hdr_6
-{
-	uint8_t datalen;
-	uint8_t medium_type;
-	uint8_t dev_specific;
-	uint8_t block_descr_len;
-};
-
-struct scsi_mode_hdr_10
-{
-	uint8_t datalen[2];
-	uint8_t medium_type;
-	uint8_t dev_specific;
-	uint8_t reserved[2];
-	uint8_t block_descr_len[2];
-};
-
-struct scsi_mode_block_descr
-{
-	uint8_t density_code;
-	uint8_t num_blocks[3];
-	uint8_t reserved;
-	uint8_t block_len[3];
-};
-
-struct scsi_log_sense
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SLS_SP				0x01
-#define	SLS_PPC				0x02
-	uint8_t page;
-#define	SLS_PAGE_CODE 			0x3F
-#define	SLS_ALL_PAGES_PAGE		0x00
-#define	SLS_OVERRUN_PAGE		0x01
-#define	SLS_ERROR_WRITE_PAGE		0x02
-#define	SLS_ERROR_READ_PAGE		0x03
-#define	SLS_ERROR_READREVERSE_PAGE	0x04
-#define	SLS_ERROR_VERIFY_PAGE		0x05
-#define	SLS_ERROR_NONMEDIUM_PAGE	0x06
-#define	SLS_ERROR_LASTN_PAGE		0x07
-#define	SLS_PAGE_CTRL_MASK		0xC0
-#define	SLS_PAGE_CTRL_THRESHOLD		0x00
-#define	SLS_PAGE_CTRL_CUMULATIVE	0x40
-#define	SLS_PAGE_CTRL_THRESH_DEFAULT	0x80
-#define	SLS_PAGE_CTRL_CUMUL_DEFAULT	0xC0
-	uint8_t reserved[2];
-	uint8_t paramptr[2];
-	uint8_t length[2];
-	uint8_t control;
-};
-
-struct scsi_log_select
-{
-	uint8_t opcode;
-	uint8_t byte2;
-/*	SLS_SP				0x01 */
-#define	SLS_PCR				0x02
-	uint8_t page;
-/*	SLS_PAGE_CTRL_MASK		0xC0 */
-/*	SLS_PAGE_CTRL_THRESHOLD		0x00 */
-/*	SLS_PAGE_CTRL_CUMULATIVE	0x40 */
-/*	SLS_PAGE_CTRL_THRESH_DEFAULT	0x80 */
-/*	SLS_PAGE_CTRL_CUMUL_DEFAULT	0xC0 */
-	uint8_t reserved[4];
-	uint8_t length[2];
-	uint8_t control;
-};
-
-struct scsi_log_header
-{
-	uint8_t page;
-	uint8_t reserved;
-	uint8_t datalen[2];
-};
-
-struct scsi_log_param_header {
-	uint8_t param_code[2];
-	uint8_t param_control;
-#define	SLP_LP				0x01
-#define	SLP_LBIN			0x02
-#define	SLP_TMC_MASK			0x0C
-#define	SLP_TMC_ALWAYS			0x00
-#define	SLP_TMC_EQUAL			0x04
-#define	SLP_TMC_NOTEQUAL		0x08
-#define	SLP_TMC_GREATER			0x0C
-#define	SLP_ETC				0x10
-#define	SLP_TSD				0x20
-#define	SLP_DS				0x40
-#define	SLP_DU				0x80
-	uint8_t param_len;
-};
-
-struct scsi_control_page {
-	uint8_t page_code;
-	uint8_t page_length;
-	uint8_t rlec;
-#define SCB_RLEC			0x01	/*Report Log Exception Cond*/
-	uint8_t queue_flags;
-#define SCP_QUEUE_ALG_MASK		0xF0
-#define SCP_QUEUE_ALG_RESTRICTED	0x00
-#define SCP_QUEUE_ALG_UNRESTRICTED	0x10
-#define SCP_QUEUE_ERR			0x02	/*Queued I/O aborted for CACs*/
-#define SCP_QUEUE_DQUE			0x01	/*Queued I/O disabled*/
-	uint8_t eca_and_aen;
-#define SCP_EECA			0x80	/*Enable Extended CA*/
-#define SCP_RAENP			0x04	/*Ready AEN Permission*/
-#define SCP_UAAENP			0x02	/*UA AEN Permission*/
-#define SCP_EAENP			0x01	/*Error AEN Permission*/
-	uint8_t reserved;
-	uint8_t aen_holdoff_period[2];
-};
-
-struct scsi_reserve
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[2];
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_release
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[2];
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_prevent
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[2];
-	uint8_t how;
-	uint8_t control;
-};
-#define	PR_PREVENT 0x01
-#define PR_ALLOW   0x00
-
-struct scsi_sync_cache
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t begin_lba[4];
-	uint8_t reserved;
-	uint8_t lb_count[2];
-	uint8_t control;	
-};
-
-
-struct scsi_changedef
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused1;
-	uint8_t how;
-	uint8_t unused[4];
-	uint8_t datalen;
-	uint8_t control;
-};
-
-struct scsi_read_buffer
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	RWB_MODE		0x07
-#define	RWB_MODE_HDR_DATA	0x00
-#define	RWB_MODE_DATA		0x02
-#define	RWB_MODE_DOWNLOAD	0x04
-#define	RWB_MODE_DOWNLOAD_SAVE	0x05
-        uint8_t buffer_id;
-        uint8_t offset[3];
-        uint8_t length[3];
-        uint8_t control;
-};
-
-struct scsi_write_buffer
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t buffer_id;
-	uint8_t offset[3];
-	uint8_t length[3];
-	uint8_t control;
-};
-
-struct scsi_rw_6
-{
-	uint8_t opcode;
-	uint8_t addr[3];
-/* only 5 bits are valid in the MSB address byte */
-#define	SRW_TOPADDR	0x1F
-	uint8_t length;
-	uint8_t control;
-};
-
-struct scsi_rw_10
-{
-	uint8_t opcode;
-#define	SRW10_RELADDR	0x01
-#define SRW10_FUA	0x08
-#define	SRW10_DPO	0x10
-	uint8_t byte2;
-	uint8_t addr[4];
-	uint8_t reserved;
-	uint8_t length[2];
-	uint8_t control;
-};
-
-struct scsi_rw_12
-{
-	uint8_t opcode;
-#define	SRW12_RELADDR	0x01
-#define SRW12_FUA	0x08
-#define	SRW12_DPO	0x10
-	uint8_t byte2;
-	uint8_t addr[4];
-	uint8_t length[4];
-	uint8_t reserved;
-	uint8_t control;
-};
-
-struct scsi_start_stop_unit
-{
-	uint8_t opcode;
-	uint8_t byte2;
-#define	SSS_IMMED		0x01
-	uint8_t reserved[2];
-	uint8_t how;
-#define	SSS_START		0x01
-#define	SSS_LOEJ		0x02
-	uint8_t control;
-};
-
-#define SC_SCSI_1 0x01
-#define SC_SCSI_2 0x03
-
-/*
- * Opcodes
- */
-
-#define	TEST_UNIT_READY		0x00
-#define REQUEST_SENSE		0x03
-#define	READ_6			0x08
-#define WRITE_6			0x0a
-#define INQUIRY			0x12
-#define MODE_SELECT_6		0x15
-#define MODE_SENSE_6		0x1a
-#define START_STOP_UNIT		0x1b
-#define START_STOP		0x1b
-#define RESERVE      		0x16
-#define RELEASE      		0x17
-#define	RECEIVE_DIAGNOSTIC	0x1c
-#define	SEND_DIAGNOSTIC		0x1d
-#define PREVENT_ALLOW		0x1e
-#define	READ_CAPACITY		0x25
-#define	READ_10			0x28
-#define WRITE_10		0x2a
-#define POSITION_TO_ELEMENT	0x2b
-#define	SYNCHRONIZE_CACHE	0x35
-#define	WRITE_BUFFER            0x3b
-#define	READ_BUFFER             0x3c
-#define	CHANGE_DEFINITION	0x40
-#define	LOG_SELECT		0x4c
-#define	LOG_SENSE		0x4d
-#ifdef XXXCAM
-#define	MODE_SENSE_10		0x5A
-#endif
-#define	MODE_SELECT_10		0x55
-#define MOVE_MEDIUM     	0xa5
-#define READ_12			0xa8
-#define WRITE_12		0xaa
-#define READ_ELEMENT_STATUS	0xb8
-
-
-/*
- * Device Types
- */
-#define T_DIRECT	0x00
-#define T_SEQUENTIAL	0x01
-#define T_PRINTER	0x02
-#define T_PROCESSOR	0x03
-#define T_WORM		0x04
-#define T_CDROM		0x05
-#define T_SCANNER 	0x06
-#define T_OPTICAL 	0x07
-#define T_CHANGER	0x08
-#define T_COMM		0x09
-#define T_ASC0		0x0a
-#define T_ASC1		0x0b
-#define	T_STORARRAY	0x0c
-#define	T_ENCLOSURE	0x0d
-#define	T_RBC		0x0e
-#define	T_OCRW		0x0f
-#define T_NODEVICE	0x1F
-#define	T_ANY		0xFF	/* Used in Quirk table matches */
-
-#define T_REMOV		1
-#define	T_FIXED		0
-
-/*
- * This length is the initial inquiry length used by the probe code, as    
- * well as the legnth necessary for aic_print_inquiry() to function 
- * correctly.  If either use requires a different length in the future, 
- * the two values should be de-coupled.
- */
-#define	SHORT_INQUIRY_LENGTH	36
-
-struct scsi_inquiry_data
-{
-	uint8_t device;
-#define	SID_TYPE(inq_data) ((inq_data)->device & 0x1f)
-#define	SID_QUAL(inq_data) (((inq_data)->device & 0xE0) >> 5)
-#define	SID_QUAL_LU_CONNECTED	0x00	/*
-					 * The specified peripheral device
-					 * type is currently connected to
-					 * logical unit.  If the target cannot
-					 * determine whether or not a physical
-					 * device is currently connected, it
-					 * shall also use this peripheral
-					 * qualifier when returning the INQUIRY
-					 * data.  This peripheral qualifier
-					 * does not mean that the device is
-					 * ready for access by the initiator.
-					 */
-#define	SID_QUAL_LU_OFFLINE	0x01	/*
-					 * The target is capable of supporting
-					 * the specified peripheral device type
-					 * on this logical unit; however, the
-					 * physical device is not currently
-					 * connected to this logical unit.
-					 */
-#define SID_QUAL_RSVD		0x02
-#define	SID_QUAL_BAD_LU		0x03	/*
-					 * The target is not capable of
-					 * supporting a physical device on
-					 * this logical unit. For this
-					 * peripheral qualifier the peripheral
-					 * device type shall be set to 1Fh to
-					 * provide compatibility with previous
-					 * versions of SCSI. All other
-					 * peripheral device type values are
-					 * reserved for this peripheral
-					 * qualifier.
-					 */
-#define	SID_QUAL_IS_VENDOR_UNIQUE(inq_data) ((SID_QUAL(inq_data) & 0x08) != 0)
-	uint8_t dev_qual2;
-#define	SID_QUAL2	0x7F
-#define	SID_IS_REMOVABLE(inq_data) (((inq_data)->dev_qual2 & 0x80) != 0)
-	uint8_t version;
-#define SID_ANSI_REV(inq_data) ((inq_data)->version & 0x07)
 #define		SCSI_REV_0		0
 #define		SCSI_REV_CCS		1
 #define		SCSI_REV_2		2
 #define		SCSI_REV_SPC		3
 #define		SCSI_REV_SPC2		4
 
-#define SID_ECMA	0x38
-#define SID_ISO		0xC0
-	uint8_t response_format;
-#define SID_AENC	0x80
-#define SID_TrmIOP	0x40
-	uint8_t additional_length;
-	uint8_t reserved[2];
-	uint8_t flags;
-#define	SID_SftRe	0x01
-#define	SID_CmdQue	0x02
-#define	SID_Linked	0x08
-#define	SID_Sync	0x10
-#define	SID_WBus16	0x20
-#define	SID_WBus32	0x40
-#define	SID_RelAdr	0x80
-#define SID_VENDOR_SIZE   8
-	char	 vendor[SID_VENDOR_SIZE];
-#define SID_PRODUCT_SIZE  16
-	char	 product[SID_PRODUCT_SIZE];
-#define SID_REVISION_SIZE 4
-	char	 revision[SID_REVISION_SIZE];
-	/*
-	 * The following fields were taken from SCSI Primary Commands - 2
-	 * (SPC-2) Revision 14, Dated 11 November 1999
-	 */
-#define	SID_VENDOR_SPECIFIC_0_SIZE	20
-	uint8_t vendor_specific0[SID_VENDOR_SPECIFIC_0_SIZE];
-	/*
-	 * An extension of SCSI Parallel Specific Values
-	 */
-#define	SID_SPI_IUS		0x01
-#define	SID_SPI_QAS		0x02
-#define	SID_SPI_CLOCK_ST	0x00
-#define	SID_SPI_CLOCK_DT	0x04
-#define	SID_SPI_CLOCK_DT_ST	0x0C
-#define	SID_SPI_MASK		0x0F
-	uint8_t spi3data;
-	uint8_t reserved2;
-	/*
-	 * Version Descriptors, stored 2 byte values.
-	 */
-	uint8_t version1[2];
-	uint8_t version2[2];
-	uint8_t version3[2];
-	uint8_t version4[2];
-	uint8_t version5[2];
-	uint8_t version6[2];
-	uint8_t version7[2];
-	uint8_t version8[2];
-
-	uint8_t reserved3[22];
-
-#define	SID_VENDOR_SPECIFIC_1_SIZE	160
-	uint8_t vendor_specific1[SID_VENDOR_SPECIFIC_1_SIZE];
-};
-
-struct scsi_vpd_unit_serial_number
-{
-	uint8_t device;
-	uint8_t page_code;
-#define SVPD_UNIT_SERIAL_NUMBER	0x80
-	uint8_t reserved;
-	uint8_t length; /* serial number length */
-#define SVPD_SERIAL_NUM_SIZE 251
-	uint8_t serial_num[SVPD_SERIAL_NUM_SIZE];
-};
-
-struct scsi_read_capacity
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t addr[4];
-	uint8_t unused[3];
-	uint8_t control;
-};
-
-struct scsi_read_capacity_data
-{
-	uint8_t addr[4];
-	uint8_t length[4];
-};
-
-struct scsi_report_luns
-{
-	uint8_t opcode;
-	uint8_t byte2;
-	uint8_t unused[3];
-	uint8_t addr[4];
-	uint8_t control;
-};
-
-struct scsi_report_luns_data {
-	uint8_t length[4];	/* length of LUN inventory, in bytes */
-	uint8_t reserved[4];	/* unused */
-	/*
-	 * LUN inventory- we only support the type zero form for now.
-	 */
-	struct {
-		uint8_t lundata[8];
-	} luns[1];
-};
-#define	RPL_LUNDATA_ATYP_MASK	0xc0	/* MBZ for type 0 lun */
-#define	RPL_LUNDATA_T0LUN	1	/* @ lundata[1] */
-
-
 struct scsi_sense_data
 {
 	uint8_t error_code;
@@ -757,41 +117,6 @@ struct scsi_sense_data
 #define SSD_FULL_SIZE sizeof(struct scsi_sense_data)
 };
 
-struct scsi_mode_header_6
-{
-	uint8_t data_length;	/* Sense data length */
-	uint8_t medium_type;
-	uint8_t dev_spec;
-	uint8_t blk_desc_len;
-};
-
-struct scsi_mode_header_10
-{
-	uint8_t data_length[2];/* Sense data length */
-	uint8_t medium_type;
-	uint8_t dev_spec;
-	uint8_t unused[2];
-	uint8_t blk_desc_len[2];
-};
-
-struct scsi_mode_page_header
-{
-	uint8_t page_code;
-	uint8_t page_length;
-};
-
-struct scsi_mode_blk_desc
-{
-	uint8_t density;
-	uint8_t nblocks[3];
-	uint8_t reserved;
-	uint8_t blklen[3];
-};
-
-#define	SCSI_DEFAULT_DENSITY	0x00	/* use 'default' density */
-#define	SCSI_SAME_DENSITY	0x7f	/* use 'same' density- >= SCSI-2 only */
-
-
 /*
  * Status Byte
  */
@@ -807,76 +132,7 @@ struct scsi_mode_blk_desc
 #define SCSI_STATUS_ACA_ACTIVE		0x30
 #define SCSI_STATUS_TASK_ABORTED	0x40
 
-struct scsi_inquiry_pattern {
-	uint8_t   type;
-	uint8_t   media_type;
-#define	SIP_MEDIA_REMOVABLE	0x01
-#define	SIP_MEDIA_FIXED		0x02
-	const char *vendor;
-	const char *product;
-	const char *revision;
-}; 
-
-struct scsi_static_inquiry_pattern {
-	uint8_t   type;
-	uint8_t   media_type;
-	char       vendor[SID_VENDOR_SIZE+1];
-	char       product[SID_PRODUCT_SIZE+1];
-	char       revision[SID_REVISION_SIZE+1];
-};
-
-struct scsi_sense_quirk_entry {
-	struct scsi_inquiry_pattern	inq_pat;
-	int				num_sense_keys;
-	int				num_ascs;
-	struct sense_key_table_entry	*sense_key_info;
-	struct asc_table_entry		*asc_info;
-};
-
-struct sense_key_table_entry {
-	uint8_t    sense_key;
-	uint32_t   action;
-	const char *desc;
-};
-
-struct asc_table_entry {
-	uint8_t    asc;
-	uint8_t    ascq;
-	uint32_t   action;
-	const char *desc;
-};
-
-struct op_table_entry {
-	uint8_t    opcode;
-	uint16_t   opmask;
-	const char  *desc;
-};
-
-struct scsi_op_quirk_entry {
-	struct scsi_inquiry_pattern	inq_pat;
-	int				num_ops;
-	struct op_table_entry		*op_table;
-};
-
-typedef enum {
-	SSS_FLAG_NONE		= 0x00,
-	SSS_FLAG_PRINT_COMMAND	= 0x01
-} scsi_sense_string_flags;
-
-extern const char *scsi_sense_key_text[];
-
 /************************* Large Disk Handling ********************************/
-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0)
-static __inline int aic_sector_div(u_long capacity, int heads, int sectors);
-
-static __inline int
-aic_sector_div(u_long capacity, int heads, int sectors)
-{
-	return (capacity / (heads * sectors));
-}
-#else
-static __inline int aic_sector_div(sector_t capacity, int heads, int sectors);
-
 static __inline int
 aic_sector_div(sector_t capacity, int heads, int sectors)
 {
@@ -884,7 +140,6 @@ aic_sector_div(sector_t capacity, int heads, int sectors)
 	sector_div(capacity, (heads * sectors));
 	return (int)capacity;
 }
-#endif
 
 /**************************** Module Library Hack *****************************/
 /*
@@ -899,138 +154,15 @@ aic_sector_div(sector_t capacity, int heads, int sectors)
 #define	AIC_LIB_ENTRY_EXPAND(x, prefix) AIC_LIB_ENTRY_CONCAT(x, prefix)
 #define AIC_LIB_ENTRY(x)		AIC_LIB_ENTRY_EXPAND(x, AIC_LIB_PREFIX)
 
-#define	aic_sense_desc			AIC_LIB_ENTRY(_sense_desc)
-#define	aic_sense_error_action		AIC_LIB_ENTRY(_sense_error_action)
-#define	aic_error_action		AIC_LIB_ENTRY(_error_action)
-#define	aic_op_desc			AIC_LIB_ENTRY(_op_desc)
-#define	aic_cdb_string			AIC_LIB_ENTRY(_cdb_string)
-#define aic_print_inquiry		AIC_LIB_ENTRY(_print_inquiry)
 #define aic_calc_syncsrate		AIC_LIB_ENTRY(_calc_syncrate)
-#define	aic_calc_syncparam		AIC_LIB_ENTRY(_calc_syncparam)
-#define	aic_calc_speed			AIC_LIB_ENTRY(_calc_speed)
-#define	aic_inquiry_match		AIC_LIB_ENTRY(_inquiry_match)
-#define	aic_static_inquiry_match	AIC_LIB_ENTRY(_static_inquiry_match)
-#define	aic_parse_brace_option		AIC_LIB_ENTRY(_parse_brace_option)
-
-/******************************************************************************/
-
-void			aic_sense_desc(int /*sense_key*/, int /*asc*/,
-				       int /*ascq*/, struct scsi_inquiry_data*,
-				       const char** /*sense_key_desc*/,
-				       const char** /*asc_desc*/);
-aic_sense_action	aic_sense_error_action(struct scsi_sense_data*,
-					       struct scsi_inquiry_data*,
-					       uint32_t /*sense_flags*/);
-uint32_t		aic_error_action(struct scsi_cmnd *,
-					 struct scsi_inquiry_data *,
-					 cam_status, u_int);
-
-#define	SF_RETRY_UA	0x01
-#define SF_NO_PRINT	0x02
-#define SF_QUIET_IR	0x04	/* Be quiet about Illegal Request reponses */
-#define SF_PRINT_ALWAYS	0x08
-
-
-const char *	aic_op_desc(uint16_t /*opcode*/, struct scsi_inquiry_data*);
-char *		aic_cdb_string(uint8_t* /*cdb_ptr*/, char* /*cdb_string*/,
-			       size_t /*len*/);
-void		aic_print_inquiry(struct scsi_inquiry_data*);
 
 u_int		aic_calc_syncsrate(u_int /*period_factor*/);
-u_int		aic_calc_syncparam(u_int /*period*/);
-u_int		aic_calc_speed(u_int width, u_int period, u_int offset,
-			       u_int min_rate);
-	
-int		aic_inquiry_match(caddr_t /*inqbuffer*/,
-				  caddr_t /*table_entry*/);
-int		aic_static_inquiry_match(caddr_t /*inqbuffer*/,
-					 caddr_t /*table_entry*/);
 
 typedef void aic_option_callback_t(u_long, int, int, int32_t);
 char *		aic_parse_brace_option(char *opt_name, char *opt_arg,
 				       char *end, int depth,
 				       aic_option_callback_t *, u_long);
 
-static __inline void	 scsi_extract_sense(struct scsi_sense_data *sense,
-					    int *error_code, int *sense_key,
-					    int *asc, int *ascq);
-static __inline void	 scsi_ulto2b(uint32_t val, uint8_t *bytes);
-static __inline void	 scsi_ulto3b(uint32_t val, uint8_t *bytes);
-static __inline void	 scsi_ulto4b(uint32_t val, uint8_t *bytes);
-static __inline uint32_t scsi_2btoul(uint8_t *bytes);
-static __inline uint32_t scsi_3btoul(uint8_t *bytes);
-static __inline int32_t	 scsi_3btol(uint8_t *bytes);
-static __inline uint32_t scsi_4btoul(uint8_t *bytes);
-
-static __inline void scsi_extract_sense(struct scsi_sense_data *sense,
-				       int *error_code, int *sense_key,
-				       int *asc, int *ascq)
-{
-	*error_code = sense->error_code & SSD_ERRCODE;
-	*sense_key = sense->flags & SSD_KEY;
-	*asc = (sense->extra_len >= 5) ? sense->add_sense_code : 0;
-	*ascq = (sense->extra_len >= 6) ? sense->add_sense_code_qual : 0;
-}
-
-static __inline void
-scsi_ulto2b(uint32_t val, uint8_t *bytes)
-{
-
-	bytes[0] = (val >> 8) & 0xff;
-	bytes[1] = val & 0xff;
-}
-
-static __inline void
-scsi_ulto3b(uint32_t val, uint8_t *bytes)
-{
-
-	bytes[0] = (val >> 16) & 0xff;
-	bytes[1] = (val >> 8) & 0xff;
-	bytes[2] = val & 0xff;
-}
-
-static __inline void
-scsi_ulto4b(uint32_t val, uint8_t *bytes)
-{
-
-	bytes[0] = (val >> 24) & 0xff;
-	bytes[1] = (val >> 16) & 0xff;
-	bytes[2] = (val >> 8) & 0xff;
-	bytes[3] = val & 0xff;
-}
-
-static __inline uint32_t
-scsi_2btoul(uint8_t *bytes)
-{
-	uint32_t rv;
-
-	rv = (bytes[0] << 8) |
-	     bytes[1];
-	return (rv);
-}
-
-static __inline uint32_t
-scsi_3btoul(uint8_t *bytes)
-{
-	uint32_t rv;
-
-	rv = (bytes[0] << 16) |
-	     (bytes[1] << 8) |
-	     bytes[2];
-	return (rv);
-}
-
-static __inline int32_t 
-scsi_3btol(uint8_t *bytes)
-{
-	uint32_t rc = scsi_3btoul(bytes);
- 
-	if (rc & 0x00800000)
-		rc |= 0xff000000;
-
-	return (int32_t) rc;
-}
-
 static __inline uint32_t
 scsi_4btoul(uint8_t *bytes)
 {