Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 1401 insertions, 0 deletions

diff --git a/drivers/scsi/aic7xxx_old/aic7xxx.reg b/drivers/scsi/aic7xxx_old/aic7xxx.reg
new file mode 100644
index 00000000000..f67b4bced01
--- /dev/null
+++ b/drivers/scsi/aic7xxx_old/aic7xxx.reg
@@ -0,0 +1,1401 @@
+/*
+ * Aic7xxx register and scratch ram definitions.
+ *
+ * Copyright (c) 1994-1998 Justin Gibbs.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions, and the following disclaimer,
+ *    without modification, immediately at the beginning of the file.
+ * 2. The name of the author may not be used to endorse or promote products
+ *    derived from this software without specific prior written permission.
+ *
+ * Where this Software is combined with software released under the terms of 
+ * the GNU General Public License ("GPL") and the terms of the GPL would require the 
+ * combined work to also be released under the terms of the GPL, the terms
+ * and conditions of this License will apply in addition to those of the
+ * GPL with the exception of any terms or conditions of this License that
+ * conflict with, or are expressly prohibited by, the GPL.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ *
+ *	$Id: aic7xxx.reg,v 1.4 1997/06/27 19:38:39 gibbs Exp $
+ */
+
+/*
+ * This file is processed by the aic7xxx_asm utility for use in assembling
+ * firmware for the aic7xxx family of SCSI host adapters as well as to generate
+ * a C header file for use in the kernel portion of the Aic7xxx driver.
+ *
+ * All page numbers refer to the Adaptec AIC-7770 Data Book available from
+ * Adaptec's Technical Documents Department 1-800-934-2766
+ */
+
+/*
+ * SCSI Sequence Control (p. 3-11).
+ * Each bit, when set starts a specific SCSI sequence on the bus
+ */
+register SCSISEQ {
+	address			0x000
+	access_mode RW
+	bit	TEMODE		0x80
+	bit	ENSELO		0x40
+	bit	ENSELI		0x20
+	bit	ENRSELI		0x10
+	bit	ENAUTOATNO	0x08
+	bit	ENAUTOATNI	0x04
+	bit	ENAUTOATNP	0x02
+	bit	SCSIRSTO	0x01
+}
+
+/*
+ * SCSI Transfer Control 0 Register (pp. 3-13).
+ * Controls the SCSI module data path.
+ */
+register SXFRCTL0 {
+	address			0x001
+	access_mode RW
+	bit	DFON		0x80
+	bit	DFPEXP		0x40
+	bit	FAST20		0x20
+	bit	CLRSTCNT	0x10
+	bit	SPIOEN		0x08
+	bit	SCAMEN		0x04
+	bit	CLRCHN		0x02
+}
+
+/*
+ * SCSI Transfer Control 1 Register (pp. 3-14,15).
+ * Controls the SCSI module data path.
+ */
+register SXFRCTL1 {
+	address			0x002
+	access_mode RW
+	bit	BITBUCKET	0x80
+	bit	SWRAPEN		0x40
+	bit	ENSPCHK		0x20
+	mask	STIMESEL	0x18
+	bit	ENSTIMER	0x04
+	bit	ACTNEGEN	0x02
+	bit	STPWEN		0x01	/* Powered Termination */
+}
+
+/*
+ * SCSI Control Signal Read Register (p. 3-15).
+ * Reads the actual state of the SCSI bus pins
+ */
+register SCSISIGI {
+	address			0x003
+	access_mode RO
+	bit	CDI		0x80
+	bit	IOI		0x40
+	bit	MSGI		0x20
+	bit	ATNI		0x10
+	bit	SELI		0x08
+	bit	BSYI		0x04
+	bit	REQI		0x02
+	bit	ACKI		0x01
+/*
+ * Possible phases in SCSISIGI
+ */
+	mask	PHASE_MASK	CDI|IOI|MSGI
+	mask	P_DATAOUT	0x00
+	mask	P_DATAIN	IOI
+	mask	P_COMMAND	CDI
+	mask	P_MESGOUT	CDI|MSGI
+	mask	P_STATUS	CDI|IOI
+	mask	P_MESGIN	CDI|IOI|MSGI
+}
+
+/*
+ * SCSI Control Signal Write Register (p. 3-16).
+ * Writing to this register modifies the control signals on the bus.  Only
+ * those signals that are allowed in the current mode (Initiator/Target) are
+ * asserted.
+ */
+register SCSISIGO {
+	address			0x003
+	access_mode WO
+	bit	CDO		0x80
+	bit	IOO		0x40
+	bit	MSGO		0x20
+	bit	ATNO		0x10
+	bit	SELO		0x08
+	bit	BSYO		0x04
+	bit	REQO		0x02
+	bit	ACKO		0x01
+/*
+ * Possible phases to write into SCSISIG0
+ */
+	mask	PHASE_MASK	CDI|IOI|MSGI
+	mask	P_DATAOUT	0x00
+	mask	P_DATAIN	IOI
+	mask	P_COMMAND	CDI
+	mask	P_MESGOUT	CDI|MSGI
+	mask	P_STATUS	CDI|IOI
+	mask	P_MESGIN	CDI|IOI|MSGI
+}
+
+/* 
+ * SCSI Rate Control (p. 3-17).
+ * Contents of this register determine the Synchronous SCSI data transfer
+ * rate and the maximum synchronous Req/Ack offset.  An offset of 0 in the
+ * SOFS (3:0) bits disables synchronous data transfers.  Any offset value
+ * greater than 0 enables synchronous transfers.
+ */
+register SCSIRATE {
+	address			0x004
+	access_mode RW
+	bit	WIDEXFER	0x80		/* Wide transfer control */
+	mask	SXFR		0x70		/* Sync transfer rate */
+	mask	SXFR_ULTRA2	0x7f		/* Sync transfer rate */
+	mask	SOFS		0x0f		/* Sync offset */
+}
+
+/*
+ * SCSI ID (p. 3-18).
+ * Contains the ID of the board and the current target on the
+ * selected channel.
+ */
+register SCSIID	{
+	address			0x005
+	access_mode RW
+	mask	TID		0xf0		/* Target ID mask */
+	mask	OID		0x0f		/* Our ID mask */
+	/*
+	 * SCSI Maximum Offset (p. 4-61 aic7890/91 Data Book)
+	 * The aic7890/91 allow an offset of up to 127 transfers in both wide
+	 * and narrow mode.
+	 */
+	alias	SCSIOFFSET
+	mask	SOFS_ULTRA2	0x7f		/* Sync offset U2 chips */
+}
+
+/*
+ * SCSI Latched Data (p. 3-19).
+ * Read/Write latches used to transfer data on the SCSI bus during
+ * Automatic or Manual PIO mode.  SCSIDATH can be used for the
+ * upper byte of a 16bit wide asynchronouse data phase transfer.
+ */
+register SCSIDATL {
+	address			0x006
+	access_mode RW
+}
+
+register SCSIDATH {
+	address			0x007
+	access_mode RW
+}
+
+/*
+ * SCSI Transfer Count (pp. 3-19,20)
+ * These registers count down the number of bytes transferred
+ * across the SCSI bus.  The counter is decremented only once
+ * the data has been safely transferred.  SDONE in SSTAT0 is
+ * set when STCNT goes to 0
+ */ 
+register STCNT {
+	address			0x008
+	size	3
+	access_mode RW
+}
+
+/*
+ * Option Mode Register (Alternate Mode) (p. 5-198)
+ * This register is used to set certain options on Ultra3 based chips.
+ * The chip must be in alternate mode (bit ALT_MODE in SFUNCT must be set)
+ */
+register OPTIONMODE {
+	address			0x008
+	access_mode RW
+	bit	AUTORATEEN	0x80
+	bit	AUTOACKEN	0x40
+	bit	ATNMGMNTEN	0x20
+	bit	BUSFREEREV	0x10
+	bit	EXPPHASEDIS	0x08
+	bit	SCSIDATL_IMGEN	0x04
+	bit	AUTO_MSGOUT_DE	0x02
+	bit	DIS_MSGIN_DUALEDGE	0x01
+}
+
+
+/*
+ * Clear SCSI Interrupt 0 (p. 3-20)
+ * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0.
+ */
+register CLRSINT0 {
+	address			0x00b
+	access_mode WO
+	bit	CLRSELDO	0x40
+	bit	CLRSELDI	0x20
+	bit	CLRSELINGO	0x10
+	bit	CLRSWRAP	0x08
+	bit	CLRSPIORDY	0x02
+}
+
+/*
+ * SCSI Status 0 (p. 3-21)
+ * Contains one set of SCSI Interrupt codes
+ * These are most likely of interest to the sequencer
+ */
+register SSTAT0	{
+	address			0x00b
+	access_mode RO
+	bit	TARGET		0x80	/* Board acting as target */
+	bit	SELDO		0x40	/* Selection Done */
+	bit	SELDI		0x20	/* Board has been selected */
+	bit	SELINGO		0x10	/* Selection In Progress */
+	bit	SWRAP		0x08	/* 24bit counter wrap */
+	bit	IOERR		0x08	/* LVD Tranceiver mode changed */
+	bit	SDONE		0x04	/* STCNT = 0x000000 */
+	bit	SPIORDY		0x02	/* SCSI PIO Ready */
+	bit	DMADONE		0x01	/* DMA transfer completed */
+}
+
+/*
+ * Clear SCSI Interrupt 1 (p. 3-23)
+ * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1.
+ */
+register CLRSINT1 {
+	address			0x00c
+	access_mode WO
+	bit	CLRSELTIMEO	0x80
+	bit	CLRATNO		0x40
+	bit	CLRSCSIRSTI	0x20
+	bit	CLRBUSFREE	0x08
+	bit	CLRSCSIPERR	0x04
+	bit	CLRPHASECHG	0x02
+	bit	CLRREQINIT	0x01
+}
+
+/*
+ * SCSI Status 1 (p. 3-24)
+ */
+register SSTAT1	{
+	address			0x00c
+	access_mode RO
+	bit	SELTO		0x80
+	bit	ATNTARG 	0x40
+	bit	SCSIRSTI	0x20
+	bit	PHASEMIS	0x10
+	bit	BUSFREE		0x08
+	bit	SCSIPERR	0x04
+	bit	PHASECHG	0x02
+	bit	REQINIT		0x01
+}
+
+/*
+ * SCSI Status 2 (pp. 3-25,26)
+ */
+register SSTAT2 {
+	address			0x00d
+	access_mode RO
+	bit	OVERRUN		0x80
+	bit	SHVALID		0x40
+	bit	WIDE_RES	0x20
+	bit	EXP_ACTIVE	0x10	/* SCSI Expander Active */
+	bit	CRCVALERR	0x08	/* CRC Value Error */
+	bit	CRCENDERR	0x04	/* CRC End Error */
+	bit	CRCREQERR	0x02	/* CRC REQ Error */
+	bit	DUAL_EDGE_ERROR	0x01	/* Invalid pins for Dual Edge phase */
+	mask	SFCNT		0x1f
+}
+
+/*
+ * SCSI Status 3 (p. 3-26)
+ */
+register SSTAT3 {
+	address			0x00e
+	access_mode RO
+	mask	SCSICNT		0xf0
+	mask	OFFCNT		0x0f
+}
+
+/*
+ * SCSI ID for the aic7890/91 chips
+ */
+register SCSIID_ULTRA2 {
+	address			0x00f
+	access_mode RW
+	mask	TID		0xf0		/* Target ID mask */
+	mask	OID		0x0f		/* Our ID mask */
+}
+
+/*
+ * SCSI Interrupt Mode 1 (p. 3-28)
+ * Setting any bit will enable the corresponding function
+ * in SIMODE0 to interrupt via the IRQ pin.
+ */
+register SIMODE0 {
+	address			0x010
+	access_mode RW
+	bit	ENSELDO		0x40
+	bit	ENSELDI		0x20
+	bit	ENSELINGO	0x10
+	bit	ENSWRAP		0x08
+	bit	ENIOERR		0x08	/* LVD Tranceiver mode changes */
+	bit	ENSDONE		0x04
+	bit	ENSPIORDY	0x02
+	bit	ENDMADONE	0x01
+}
+
+/*
+ * SCSI Interrupt Mode 1 (pp. 3-28,29)
+ * Setting any bit will enable the corresponding function
+ * in SIMODE1 to interrupt via the IRQ pin.
+ */
+register SIMODE1 {
+	address			0x011
+	access_mode RW
+	bit	ENSELTIMO	0x80
+	bit	ENATNTARG	0x40
+	bit	ENSCSIRST	0x20
+	bit	ENPHASEMIS	0x10
+	bit	ENBUSFREE	0x08
+	bit	ENSCSIPERR	0x04
+	bit	ENPHASECHG	0x02
+	bit	ENREQINIT	0x01
+}
+
+/*
+ * SCSI Data Bus (High) (p. 3-29)
+ * This register reads data on the SCSI Data bus directly.
+ */
+register SCSIBUSL {
+	address			0x012
+	access_mode RO
+}
+
+register SCSIBUSH {
+	address			0x013
+	access_mode RO
+}
+
+/*
+ * SCSI/Host Address (p. 3-30)
+ * These registers hold the host address for the byte about to be
+ * transferred on the SCSI bus.  They are counted up in the same
+ * manner as STCNT is counted down.  SHADDR should always be used
+ * to determine the address of the last byte transferred since HADDR
+ * can be skewed by write ahead.
+ */
+register SHADDR {
+	address			0x014
+	size	4
+	access_mode RO
+}
+
+/*
+ * Selection Timeout Timer (p. 3-30)
+ */
+register SELTIMER {
+	address			0x018
+	access_mode RW
+	bit	STAGE6		0x20
+	bit	STAGE5		0x10
+	bit	STAGE4		0x08
+	bit	STAGE3		0x04
+	bit	STAGE2		0x02
+	bit	STAGE1		0x01
+}
+
+/*
+ * Selection/Reselection ID (p. 3-31)
+ * Upper four bits are the device id.  The ONEBIT is set when the re/selecting
+ * device did not set its own ID.
+ */
+register SELID {
+	address			0x019
+	access_mode RW
+	mask	SELID_MASK	0xf0
+	bit	ONEBIT		0x08
+}
+
+/*
+ * Serial Port I/O Cabability register (p. 4-95 aic7860 Data Book)
+ * Indicates if external logic has been attached to the chip to
+ * perform the tasks of accessing a serial eeprom, testing termination
+ * strength, and performing cable detection.  On the aic7860, most of
+ * these features are handled on chip, but on the aic7855 an attached
+ * aic3800 does the grunt work.
+ */
+register SPIOCAP {
+	address			0x01b
+	access_mode RW
+	bit	SOFT1		0x80
+	bit	SOFT0		0x40
+	bit	SOFTCMDEN	0x20	
+	bit	HAS_BRDCTL	0x10	/* External Board control */
+	bit	SEEPROM		0x08	/* External serial eeprom logic */
+	bit	EEPROM		0x04	/* Writable external BIOS ROM */
+	bit	ROM		0x02	/* Logic for accessing external ROM */
+	bit	SSPIOCPS	0x01	/* Termination and cable detection */
+}
+
+/*
+ * SCSI Block Control (p. 3-32)
+ * Controls Bus type and channel selection.  In a twin channel configuration
+ * addresses 0x00-0x1e are gated to the appropriate channel based on this
+ * register.  SELWIDE allows for the coexistence of 8bit and 16bit devices
+ * on a wide bus.
+ */
+register SBLKCTL {
+	address			0x01f
+	access_mode RW
+	bit	DIAGLEDEN	0x80	/* Aic78X0 only */
+	bit	DIAGLEDON	0x40	/* Aic78X0 only */
+	bit	AUTOFLUSHDIS	0x20
+	bit	SELBUSB		0x08
+	bit	ENAB40		0x08	/* LVD transceiver active */
+	bit	ENAB20		0x04	/* SE/HVD transceiver active */
+	bit	SELWIDE		0x02
+	bit	XCVR		0x01	/* External transceiver active */
+}
+
+/*
+ * Sequencer Control (p. 3-33)
+ * Error detection mode and speed configuration
+ */
+register SEQCTL {
+	address			0x060
+	access_mode RW
+	bit	PERRORDIS	0x80
+	bit	PAUSEDIS	0x40
+	bit	FAILDIS		0x20
+	bit	FASTMODE	0x10
+	bit	BRKADRINTEN	0x08
+	bit	STEP		0x04
+	bit	SEQRESET	0x02
+	bit	LOADRAM		0x01
+}
+
+/*
+ * Sequencer RAM Data (p. 3-34)
+ * Single byte window into the Scratch Ram area starting at the address
+ * specified by SEQADDR0 and SEQADDR1.  To write a full word, simply write
+ * four bytes in succession.  The SEQADDRs will increment after the most
+ * significant byte is written
+ */
+register SEQRAM {
+	address			0x061
+	access_mode RW
+}
+
+/*
+ * Sequencer Address Registers (p. 3-35)
+ * Only the first bit of SEQADDR1 holds addressing information
+ */
+register SEQADDR0 {
+	address			0x062
+	access_mode RW
+}
+
+register SEQADDR1 {
+	address			0x063
+	access_mode RW
+	mask	SEQADDR1_MASK	0x01
+}
+
+/*
+ * Accumulator
+ * We cheat by passing arguments in the Accumulator up to the kernel driver
+ */
+register ACCUM {
+	address			0x064
+	access_mode RW
+	accumulator
+}
+
+register SINDEX	{
+	address			0x065
+	access_mode RW
+	sindex
+}
+
+register DINDEX {
+	address			0x066
+	access_mode RW
+}
+
+register ALLONES {
+	address			0x069
+	access_mode RO
+	allones
+}
+
+register ALLZEROS {
+	address			0x06a
+	access_mode RO
+	allzeros
+}
+
+register NONE {
+	address			0x06a
+	access_mode WO
+	none
+}
+
+register FLAGS {
+	address			0x06b
+	access_mode RO
+	bit	ZERO		0x02
+	bit	CARRY		0x01
+}
+
+register SINDIR	{
+	address			0x06c
+	access_mode RO
+}
+
+register DINDIR	 {
+	address			0x06d
+	access_mode WO
+}
+
+register FUNCTION1 {
+	address			0x06e
+	access_mode RW
+}
+
+register STACK {
+	address			0x06f
+	access_mode RO
+}
+
+/*
+ * Board Control (p. 3-43)
+ */
+register BCTL {
+	address			0x084
+	access_mode RW
+	bit	ACE		0x08
+	bit	ENABLE		0x01
+}
+
+register DSCOMMAND0 {
+	address			0x084
+	access_mode RW
+	bit	CACHETHEN	0x80
+	bit	DPARCKEN	0x40
+	bit	MPARCKEN	0x20
+	bit	EXTREQLCK	0x10
+	bit	INTSCBRAMSEL	0x08
+	bit	RAMPS		0x04
+	bit	USCBSIZE32	0x02
+	bit	CIOPARCKEN	0x01
+}
+
+/*
+ * On the aic78X0 chips, Board Control is replaced by the DSCommand
+ * register (p. 4-64)
+ */
+register DSCOMMAND {
+	address			0x084
+	access_mode RW
+	bit	CACHETHEN	0x80	/* Cache Threshold enable */
+	bit	DPARCKEN	0x40	/* Data Parity Check Enable */
+	bit	MPARCKEN	0x20	/* Memory Parity Check Enable */
+	bit	EXTREQLCK	0x10	/* External Request Lock */
+}
+
+/*
+ * Bus On/Off Time (p. 3-44)
+ */
+register BUSTIME {
+	address			0x085
+	access_mode RW
+	mask	BOFF		0xf0
+	mask	BON		0x0f
+}
+
+/*
+ * Bus Speed (p. 3-45)
+ */
+register BUSSPD {
+	address			0x086
+	access_mode RW
+	mask	DFTHRSH		0xc0
+	mask	STBOFF		0x38
+	mask	STBON		0x07
+	mask	DFTHRSH_100	0xc0
+}
+
+/*
+ * Host Control (p. 3-47) R/W
+ * Overall host control of the device.
+ */
+register HCNTRL {
+	address			0x087
+	access_mode RW
+	bit	POWRDN		0x40
+	bit	SWINT		0x10
+	bit	IRQMS		0x08
+	bit	PAUSE		0x04
+	bit	INTEN		0x02
+	bit	CHIPRST		0x01
+	bit	CHIPRSTACK	0x01
+}
+
+/*
+ * Host Address (p. 3-48)
+ * This register contains the address of the byte about
+ * to be transferred across the host bus.
+ */
+register HADDR {
+	address			0x088
+	size	4
+	access_mode RW
+}
+
+register HCNT {
+	address			0x08c
+	size	3
+	access_mode RW
+}
+
+/*
+ * SCB Pointer (p. 3-49)
+ * Gate one of the four SCBs into the SCBARRAY window.
+ */
+register SCBPTR {
+	address			0x090
+	access_mode RW
+}
+
+/*
+ * Interrupt Status (p. 3-50)
+ * Status for system interrupts
+ */
+register INTSTAT {
+	address			0x091
+	access_mode RW
+	bit	BRKADRINT 0x08
+	bit	SCSIINT	  0x04
+	bit	CMDCMPLT  0x02
+	bit	SEQINT    0x01
+	mask	BAD_PHASE	SEQINT		/* unknown scsi bus phase */
+	mask	SEND_REJECT	0x10|SEQINT	/* sending a message reject */
+	mask	NO_IDENT	0x20|SEQINT	/* no IDENTIFY after reconnect*/
+	mask	NO_MATCH	0x30|SEQINT	/* no cmd match for reconnect */
+	mask	EXTENDED_MSG	0x40|SEQINT	/* Extended message received */
+	mask	WIDE_RESIDUE	0x50|SEQINT	/* need kernel to back up */
+						/* the SG array for us */
+	mask	REJECT_MSG	0x60|SEQINT	/* Reject message received */
+	mask	BAD_STATUS	0x70|SEQINT	/* Bad status from target */
+	mask	RESIDUAL	0x80|SEQINT	/* Residual byte count != 0 */
+	mask	AWAITING_MSG	0xa0|SEQINT	/*
+						 * Kernel requested to specify
+						 * a message to this target
+						 * (command was null), so tell
+						 * it that it can fill the
+						 * message buffer.
+						 */
+	mask	SEQ_SG_FIXUP	0xb0|SEQINT	/* need help with fixing up
+						 * the sg array pointer after
+						 * a phasemis with no valid
+						 * sg elements in the shadow
+						 * pipeline.
+						 */
+	mask	TRACEPOINT2	0xc0|SEQINT
+	mask	MSGIN_PHASEMIS	0xd0|SEQINT	/*
+						 * Target changed phase on us
+						 * when we were expecting
+						 * another msgin byte.
+						 */
+	mask	DATA_OVERRUN	0xe0|SEQINT	/*
+						 * Target attempted to write
+						 * beyond the bounds of its
+						 * command.
+						 */
+
+	mask	SEQINT_MASK	0xf0|SEQINT	/* SEQINT Status Codes */
+	mask	INT_PEND  (BRKADRINT|SEQINT|SCSIINT|CMDCMPLT)
+}
+
+/*
+ * Hard Error (p. 3-53)
+ * Reporting of catastrophic errors.  You usually cannot recover from
+ * these without a full board reset.
+ */
+register ERROR {
+	address			0x092
+	access_mode RO
+	bit	CIOPARERR	0x80	/* Ultra2 only */
+	bit	PCIERRSTAT	0x40	/* PCI only */
+	bit	MPARERR		0x20	/* PCI only */
+	bit	DPARERR		0x10	/* PCI only */
+	bit	SQPARERR	0x08
+	bit	ILLOPCODE	0x04
+	bit	ILLSADDR	0x02
+	bit	DSCTMOUT	0x02	/* Ultra3 only */
+	bit	ILLHADDR	0x01
+}
+
+/*
+ * Clear Interrupt Status (p. 3-52)
+ */
+register CLRINT {
+	address			0x092
+	access_mode WO
+	bit	CLRPARERR	0x10	/* PCI only */
+	bit	CLRBRKADRINT	0x08
+	bit	CLRSCSIINT      0x04
+	bit	CLRCMDINT 	0x02
+	bit	CLRSEQINT 	0x01
+}
+
+register DFCNTRL {
+	address			0x093
+	access_mode RW
+	bit	PRELOADEN	0x80	/* aic7890 only */
+	bit	WIDEODD		0x40
+	bit	SCSIEN		0x20
+	bit	SDMAEN		0x10
+	bit	SDMAENACK	0x10
+	bit	HDMAEN		0x08
+	bit	HDMAENACK	0x08
+	bit	DIRECTION	0x04
+	bit	FIFOFLUSH	0x02
+	bit	FIFORESET	0x01
+}
+
+register DFSTATUS {
+	address			0x094
+	access_mode RO
+	bit	PRELOAD_AVAIL	0x80
+	bit	DWORDEMP	0x20
+	bit	MREQPEND	0x10
+	bit	HDONE		0x08
+	bit	DFTHRESH	0x04
+	bit	FIFOFULL	0x02
+	bit	FIFOEMP		0x01
+}
+
+register DFDAT {
+	address			0x099
+	access_mode RW
+}
+
+/*
+ * SCB Auto Increment (p. 3-59)
+ * Byte offset into the SCB Array and an optional bit to allow auto
+ * incrementing of the address during download and upload operations
+ */
+register SCBCNT {
+	address			0x09a
+	access_mode RW
+	bit	SCBAUTO		0x80
+	mask	SCBCNT_MASK	0x1f
+}
+
+/*
+ * Queue In FIFO (p. 3-60)
+ * Input queue for queued SCBs (commands that the seqencer has yet to start)
+ */
+register QINFIFO {
+	address			0x09b
+	access_mode RW
+}
+
+/*
+ * Queue In Count (p. 3-60)
+ * Number of queued SCBs
+ */
+register QINCNT	{
+	address			0x09c
+	access_mode RO
+}
+
+/*
+ * SCSIDATL IMAGE Register (p. 5-104)
+ * Write to this register also go to SCSIDATL but this register will preserve
+ * the data for later reading as long as the SCSIDATL_IMGEN bit in the
+ * OPTIONMODE register is set.
+ */
+register SCSIDATL_IMG {
+	address			0x09c
+	access_mode RW
+}
+
+/*
+ * Queue Out FIFO (p. 3-61)
+ * Queue of SCBs that have completed and await the host
+ */
+register QOUTFIFO {
+	address			0x09d
+	access_mode WO
+}
+
+/*
+ * CRC Control 1 Register (p. 5-105)
+ * Control bits for the Ultra 160/m CRC facilities
+ */
+register CRCCONTROL1 {
+	address			0x09d
+	access_mode RW
+	bit	CRCONSEEN	0x80 /* CRC ON Single Edge ENable */
+	bit	CRCVALCHKEN	0x40 /* CRC Value Check Enable */
+	bit	CRCENDCHKEN	0x20 /* CRC End Check Enable */
+	bit	CRCREQCHKEN	0x10
+	bit	TARGCRCENDEN	0x08 /* Enable End CRC transfer when target */
+	bit	TARGCRCCNTEN	0x04 /* Enable CRC transfer when target */
+}
+
+/*
+ * Queue Out Count (p. 3-61)
+ * Number of queued SCBs in the Out FIFO
+ */
+register QOUTCNT {
+	address			0x09e
+	access_mode RO
+}
+
+/*
+ * SCSI Phase Register (p. 5-106)
+ * Current bus phase
+ */
+register SCSIPHASE {
+	address			0x09e
+	access_mode RO
+	bit	SP_STATUS		0x20
+	bit	SP_COMMAND		0x10
+	bit	SP_MSG_IN		0x08
+	bit	SP_MSG_OUT		0x04
+	bit	SP_DATA_IN		0x02
+	bit	SP_DATA_OUT	0x01
+}
+
+/*
+ * Special Function
+ */
+register SFUNCT {
+	address			0x09f
+	access_mode RW
+	bit	ALT_MODE	0x80
+}
+
+/*
+ * SCB Definition (p. 5-4)
+ */
+scb {
+	address			0x0a0
+	SCB_CONTROL {
+		size	1
+		bit	MK_MESSAGE      0x80
+		bit	DISCENB         0x40
+		bit	TAG_ENB		0x20
+		bit	DISCONNECTED	0x04
+		mask	SCB_TAG_TYPE	0x03
+	}
+	SCB_TCL {
+		size	1
+		bit	SELBUSB		0x08
+		mask	TID		0xf0
+		mask	LID		0x07
+	}
+	SCB_TARGET_STATUS {
+		size	1
+	}
+	SCB_SGCOUNT {
+		size	1
+	}
+	SCB_SGPTR {
+		size	4
+	}
+	SCB_RESID_SGCNT {
+		size	1
+	}
+	SCB_RESID_DCNT	{
+		size	3
+	}
+	SCB_DATAPTR {
+		size	4
+	}
+	SCB_DATACNT {
+		/*
+		 * Really only 3 bytes, but padded to make
+		 * the kernel's job easier.
+		 */
+		size	4
+	}
+	SCB_CMDPTR {
+		size	4
+	}
+	SCB_CMDLEN {
+		size	1
+	}
+	SCB_TAG {
+		size	1
+	}
+	SCB_NEXT {
+		size	1
+	}
+	SCB_PREV {
+		size	1
+	}
+	SCB_BUSYTARGETS {
+		size	4
+	}
+}
+
+const	SG_SIZEOF	0x08		/* sizeof(struct ahc_dma) */
+
+/* --------------------- AHA-2840-only definitions -------------------- */
+
+register SEECTL_2840 {
+	address			0x0c0
+	access_mode RW
+	bit	CS_2840		0x04
+	bit	CK_2840		0x02
+	bit	DO_2840		0x01
+}
+
+register STATUS_2840 {
+	address			0x0c1
+	access_mode RW
+	bit	EEPROM_TF	0x80
+	mask	BIOS_SEL	0x60
+	mask	ADSEL		0x1e
+	bit	DI_2840		0x01
+}
+
+/* --------------------- AIC-7870-only definitions -------------------- */
+
+register DSPCISTATUS {
+	address			0x086
+	mask	DFTHRSH_100	0xc0
+}
+
+register CCHADDR {
+	address			0x0E0
+	size 8
+}
+
+register CCHCNT {
+	address			0x0E8
+}
+
+register CCSGRAM {
+	address			0x0E9
+}
+
+register CCSGADDR {
+	address			0x0EA
+}
+
+register CCSGCTL {
+	address			0x0EB
+	bit	CCSGDONE	0x80
+	bit	CCSGEN		0x08
+	bit	FLAG		0x02
+	bit	CCSGRESET	0x01
+}
+
+register CCSCBCNT {
+	address			0xEF
+}
+
+register CCSCBCTL {
+	address			0x0EE
+	bit	CCSCBDONE	0x80
+	bit	ARRDONE		0x40	/* SCB Array prefetch done */
+	bit	CCARREN		0x10
+	bit	CCSCBEN		0x08
+	bit	CCSCBDIR	0x04
+	bit	CCSCBRESET	0x01
+}
+
+register CCSCBADDR {
+	address			0x0ED
+}
+
+register CCSCBRAM {
+	address			0xEC
+}
+
+register CCSCBPTR {
+	address			0x0F1
+}
+
+register HNSCB_QOFF {
+	address			0x0F4
+}
+
+register HESCB_QOFF {
+	address			0x0F5
+}
+
+register SNSCB_QOFF {
+	address			0x0F6
+}
+
+register SESCB_QOFF {
+	address			0x0F7
+}
+
+register SDSCB_QOFF {
+	address			0x0F8
+}
+
+register QOFF_CTLSTA {
+	address			0x0FA
+	bit	ESTABLISH_SCB_AVAIL	0x80
+	bit	SCB_AVAIL	0x40
+	bit	SNSCB_ROLLOVER	0x20
+	bit	SDSCB_ROLLOVER	0x10
+	bit	SESCB_ROLLOVER	0x08
+	mask	SCB_QSIZE	0x07
+	mask	SCB_QSIZE_256	0x06
+}
+
+register DFF_THRSH {
+	address			0x0FB
+	mask	WR_DFTHRSH	0x70
+	mask	RD_DFTHRSH	0x07
+	mask	RD_DFTHRSH_MIN	0x00
+	mask	RD_DFTHRSH_25	0x01
+	mask	RD_DFTHRSH_50	0x02
+	mask	RD_DFTHRSH_63	0x03
+	mask	RD_DFTHRSH_75	0x04
+	mask	RD_DFTHRSH_85	0x05
+	mask	RD_DFTHRSH_90	0x06
+	mask	RD_DFTHRSH_MAX	0x07
+	mask	WR_DFTHRSH_MIN	0x00
+	mask	WR_DFTHRSH_25	0x10
+	mask	WR_DFTHRSH_50	0x20
+	mask	WR_DFTHRSH_63	0x30
+	mask	WR_DFTHRSH_75	0x40
+	mask	WR_DFTHRSH_85	0x50
+	mask	WR_DFTHRSH_90	0x60
+	mask	WR_DFTHRSH_MAX	0x70
+}
+
+register SG_CACHEPTR {
+	access_mode RW
+	address			0x0fc
+	mask	SG_USER_DATA	0xfc
+	bit	LAST_SEG	0x02
+	bit	LAST_SEG_DONE	0x01
+}
+
+register BRDCTL	{
+	address			0x01d
+	bit	BRDDAT7		0x80
+	bit	BRDDAT6		0x40
+	bit	BRDDAT5		0x20
+	bit	BRDSTB		0x10
+	bit	BRDCS		0x08
+	bit	BRDRW		0x04
+	bit	BRDCTL1		0x02
+	bit	BRDCTL0		0x01
+	/* 7890 Definitions */
+	bit	BRDDAT4		0x10
+	bit	BRDDAT3		0x08
+	bit	BRDDAT2		0x04
+	bit	BRDRW_ULTRA2	0x02
+	bit	BRDSTB_ULTRA2	0x01
+}
+
+/*
+ * Serial EEPROM Control (p. 4-92 in 7870 Databook)
+ * Controls the reading and writing of an external serial 1-bit
+ * EEPROM Device.  In order to access the serial EEPROM, you must
+ * first set the SEEMS bit that generates a request to the memory
+ * port for access to the serial EEPROM device.  When the memory
+ * port is not busy servicing another request, it reconfigures
+ * to allow access to the serial EEPROM.  When this happens, SEERDY
+ * gets set high to verify that the memory port access has been
+ * granted.  
+ *
+ * After successful arbitration for the memory port, the SEECS bit of 
+ * the SEECTL register is connected to the chip select.  The SEECK, 
+ * SEEDO, and SEEDI are connected to the clock, data out, and data in 
+ * lines respectively.  The SEERDY bit of SEECTL is useful in that it 
+ * gives us an 800 nsec timer.  After a write to the SEECTL register, 
+ * the SEERDY goes high 800 nsec later.  The one exception to this is 
+ * when we first request access to the memory port.  The SEERDY goes 
+ * high to signify that access has been granted and, for this case, has 
+ * no implied timing.
+ *
+ * See 93cx6.c for detailed information on the protocol necessary to 
+ * read the serial EEPROM.
+ */
+register SEECTL {
+	address			0x01e
+	bit	EXTARBACK	0x80
+	bit	EXTARBREQ	0x40
+	bit	SEEMS		0x20
+	bit	SEERDY		0x10
+	bit	SEECS		0x08
+	bit	SEECK		0x04
+	bit	SEEDO		0x02
+	bit	SEEDI		0x01
+}
+/* ---------------------- Scratch RAM Offsets ------------------------- */
+/* These offsets are either to values that are initialized by the board's
+ * BIOS or are specified by the sequencer code.
+ *
+ * The host adapter card (at least the BIOS) uses 20-2f for SCSI
+ * device information, 32-33 and 5a-5f as well. As it turns out, the
+ * BIOS trashes 20-2f, writing the synchronous negotiation results
+ * on top of the BIOS values, so we re-use those for our per-target
+ * scratchspace (actually a value that can be copied directly into
+ * SCSIRATE).  The kernel driver will enable synchronous negotiation
+ * for all targets that have a value other than 0 in the lower four
+ * bits of the target scratch space.  This should work regardless of
+ * whether the bios has been installed.
+ */
+
+scratch_ram {
+	address			0x020
+
+	/*
+	 * 1 byte per target starting at this address for configuration values
+	 */
+	TARG_SCSIRATE {
+		size		16
+	}
+	/*
+	 * Bit vector of targets that have ULTRA enabled.
+	 */
+	ULTRA_ENB {
+		size		2
+	}
+	/*
+	 * Bit vector of targets that have disconnection disabled.
+	 */
+	DISC_DSB {
+		size		2
+	}
+	/*
+	 * Single byte buffer used to designate the type or message
+	 * to send to a target.
+	 */
+	MSG_OUT {
+		size		1
+	}
+	/* Parameters for DMA Logic */
+	DMAPARAMS {
+		size		1
+		bit	PRELOADEN	0x80
+		bit	WIDEODD		0x40
+		bit	SCSIEN		0x20
+		bit	SDMAEN		0x10
+		bit	SDMAENACK	0x10
+		bit	HDMAEN		0x08
+		bit	HDMAENACK	0x08
+		bit	DIRECTION	0x04
+		bit	FIFOFLUSH	0x02
+		bit	FIFORESET	0x01
+	}
+	SEQ_FLAGS {
+		size		1
+		bit	IDENTIFY_SEEN	0x80
+		bit	SCBPTR_VALID	0x20
+		bit	DPHASE		0x10
+		bit	AMTARGET	0x08
+		bit	WIDE_BUS	0x02
+		bit	TWIN_BUS	0x01
+	}
+	/*
+	 * Temporary storage for the
+	 * target/channel/lun of a
+	 * reconnecting target
+	 */
+	SAVED_TCL {
+		size		1
+	}
+	/* Working value of the number of SG segments left */
+	SG_COUNT {
+		size		1
+	}
+	/* Working value of SG pointer */
+	SG_NEXT	{
+		size		4
+	}
+	/*
+	 * The last bus phase as seen by the sequencer. 
+	 */
+	LASTPHASE {
+		size		1
+		bit	CDI		0x80
+		bit	IOI		0x40
+		bit	MSGI		0x20
+		mask	PHASE_MASK	CDI|IOI|MSGI
+		mask	P_DATAOUT	0x00
+		mask	P_DATAIN	IOI
+		mask	P_COMMAND	CDI
+		mask	P_MESGOUT	CDI|MSGI
+		mask	P_STATUS	CDI|IOI
+		mask	P_MESGIN	CDI|IOI|MSGI
+		mask	P_BUSFREE	0x01
+	}
+	/*
+	 * head of list of SCBs awaiting
+	 * selection
+	 */
+	WAITING_SCBH {
+		size		1
+	}
+	/*
+	 * head of list of SCBs that are
+	 * disconnected.  Used for SCB
+	 * paging.
+	 */
+	DISCONNECTED_SCBH {
+		size		1
+	}
+	/*
+	 * head of list of SCBs that are
+	 * not in use.  Used for SCB paging.
+	 */
+	FREE_SCBH {
+		size		1
+	}
+	/*
+	 * Address of the hardware scb array in the host.
+	 */
+	HSCB_ADDR {
+		size		4
+	}
+	/*
+	 * Address of the 256 byte array storing the SCBID of outstanding
+	 * untagged SCBs indexed by TCL.
+	 */
+	SCBID_ADDR {
+		size		4
+	}
+	/*
+	 * Address of the array of command descriptors used to store
+	 * information about incoming selections.
+	 */
+	TMODE_CMDADDR {
+		size		4
+	}
+	KERNEL_QINPOS {
+		size		1
+	}
+	QINPOS {
+		size		1
+	}
+	QOUTPOS {
+		size		1
+	}
+	/*
+	 * Offset into the command descriptor array for the next
+	 * available desciptor to use.
+	 */
+	TMODE_CMDADDR_NEXT {
+		size		1
+	}
+	ARG_1 {
+		size		1
+		mask	SEND_MSG	0x80
+		mask	SEND_SENSE	0x40
+		mask	SEND_REJ	0x20
+		mask	MSGOUT_PHASEMIS	0x10
+		alias	RETURN_1
+	}
+	ARG_2 {
+		size		1
+		alias	RETURN_2
+	}
+
+	/*
+	 * Snapshot of MSG_OUT taken after each message is sent.
+	 */
+	LAST_MSG {
+		size		1
+	}
+
+	/*
+	 * Number of times we have filled the CCSGRAM with prefetched
+	 * SG elements.
+	 */
+	PREFETCH_CNT {
+		size		1
+	}
+
+
+	/*
+	 * These are reserved registers in the card's scratch ram.  Some of
+	 * the values are specified in the AHA2742 technical reference manual
+	 * and are initialized by the BIOS at boot time.
+	 */
+	SCSICONF {
+		address		0x05a
+		size		1
+		bit	TERM_ENB	0x80
+		bit	RESET_SCSI	0x40
+		mask	HSCSIID		0x07	/* our SCSI ID */
+		mask	HWSCSIID	0x0f	/* our SCSI ID if Wide Bus */
+	}
+	HOSTCONF {
+		address		0x05d
+		size		1
+	}
+	HA_274_BIOSCTRL	{
+		address		0x05f
+		size		1
+		mask	BIOSMODE		0x30
+		mask	BIOSDISABLED		0x30	
+		bit	CHANNEL_B_PRIMARY	0x08
+	}
+	/*
+	 * Per target SCSI offset values for Ultra2 controllers.
+	 */
+	TARG_OFFSET {
+		address		0x070
+		size		16
+	}
+}
+
+const SCB_LIST_NULL	0xff
+
+const CCSGADDR_MAX	0x80
+const CCSGRAM_MAXSEGS	16
+
+/* Offsets into the SCBID array where different data is stored */
+const UNTAGGEDSCB_OFFSET	0
+const QOUTFIFO_OFFSET		1
+const QINFIFO_OFFSET		2
+
+/* WDTR Message values */
+const BUS_8_BIT			0x00
+const BUS_16_BIT		0x01
+const BUS_32_BIT		0x02
+
+/* Offset maximums */
+const MAX_OFFSET_8BIT		0x0f
+const MAX_OFFSET_16BIT		0x08
+const MAX_OFFSET_ULTRA2		0x7f
+const HOST_MSG			0xff
+
+/* Target mode command processing constants */
+const CMD_GROUP_CODE_SHIFT	0x05
+const CMD_GROUP0_BYTE_DELTA	-4
+const CMD_GROUP2_BYTE_DELTA	-6
+const CMD_GROUP4_BYTE_DELTA	4
+const CMD_GROUP5_BYTE_DELTA	11
+
+/*
+ * Downloaded (kernel inserted) constants
+ */
+
+/*
+ * Number of command descriptors in the command descriptor array.
+ */
+const TMODE_NUMCMDS	download