[SCSI] mvsas: split driver into multiple files

Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

1 files changed, 441 insertions, 0 deletions

diff --git a/drivers/scsi/mvsas/mv_defs.h b/drivers/scsi/mvsas/mv_defs.h
new file mode 100644
index 00000000000..d8e96a3e5a2
--- /dev/null
+++ b/drivers/scsi/mvsas/mv_defs.h
@@ -0,0 +1,441 @@
+/*
+	mv_defs.h - Marvell 88SE6440 SAS/SATA support
+
+	Copyright 2007 Red Hat, Inc.
+	Copyright 2008 Marvell. <kewei@marvell.com>
+
+	This program is free software; you can redistribute it and/or
+	modify it under the terms of the GNU General Public License as
+	published by the Free Software Foundation; either version 2,
+	or (at your option) any later version.
+
+	This program is distributed in the hope that it will be useful,
+	but WITHOUT ANY WARRANTY; without even the implied warranty
+	of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+	See the GNU General Public License for more details.
+
+	You should have received a copy of the GNU General Public
+	License along with this program; see the file COPYING.	If not,
+	write to the Free Software Foundation, 675 Mass Ave, Cambridge,
+	MA 02139, USA.
+
+ */
+
+#ifndef _MV_DEFS_H_
+#define _MV_DEFS_H_
+
+/* driver compile-time configuration */
+enum driver_configuration {
+	MVS_TX_RING_SZ		= 1024,	/* TX ring size (12-bit) */
+	MVS_RX_RING_SZ		= 1024, /* RX ring size (12-bit) */
+					/* software requires power-of-2
+					   ring size */
+
+	MVS_SLOTS		= 512,	/* command slots */
+	MVS_SLOT_BUF_SZ		= 8192, /* cmd tbl + IU + status + PRD */
+	MVS_SSP_CMD_SZ		= 64,	/* SSP command table buffer size */
+	MVS_ATA_CMD_SZ		= 96,	/* SATA command table buffer size */
+	MVS_OAF_SZ		= 64,	/* Open address frame buffer size */
+
+	MVS_RX_FIS_COUNT	= 17,	/* Optional rx'd FISs (max 17) */
+
+	MVS_QUEUE_SIZE		= 30,	/* Support Queue depth */
+	MVS_CAN_QUEUE		= MVS_SLOTS - 1,	/* SCSI Queue depth */
+};
+
+/* unchangeable hardware details */
+enum hardware_details {
+	MVS_MAX_PHYS		= 8,	/* max. possible phys */
+	MVS_MAX_PORTS		= 8,	/* max. possible ports */
+	MVS_RX_FISL_SZ		= 0x400 + (MVS_RX_FIS_COUNT * 0x100),
+};
+
+/* peripheral registers (BAR2) */
+enum peripheral_registers {
+	SPI_CTL			= 0x10,	/* EEPROM control */
+	SPI_CMD			= 0x14,	/* EEPROM command */
+	SPI_DATA		= 0x18, /* EEPROM data */
+};
+
+enum peripheral_register_bits {
+	TWSI_RDY		= (1U << 7),	/* EEPROM interface ready */
+	TWSI_RD			= (1U << 4),	/* EEPROM read access */
+
+	SPI_ADDR_MASK		= 0x3ffff,	/* bits 17:0 */
+};
+
+enum hw_register_bits {
+	/* MVS_GBL_CTL */
+	INT_EN			= (1U << 1),	/* Global int enable */
+	HBA_RST			= (1U << 0),	/* HBA reset */
+
+	/* MVS_GBL_INT_STAT */
+	INT_XOR			= (1U << 4),	/* XOR engine event */
+	INT_SAS_SATA		= (1U << 0),	/* SAS/SATA event */
+
+	/* MVS_GBL_PORT_TYPE */			/* shl for ports 1-3 */
+	SATA_TARGET		= (1U << 16),	/* port0 SATA target enable */
+	MODE_AUTO_DET_PORT7 = (1U << 15),	/* port0 SAS/SATA autodetect */
+	MODE_AUTO_DET_PORT6 = (1U << 14),
+	MODE_AUTO_DET_PORT5 = (1U << 13),
+	MODE_AUTO_DET_PORT4 = (1U << 12),
+	MODE_AUTO_DET_PORT3 = (1U << 11),
+	MODE_AUTO_DET_PORT2 = (1U << 10),
+	MODE_AUTO_DET_PORT1 = (1U << 9),
+	MODE_AUTO_DET_PORT0 = (1U << 8),
+	MODE_AUTO_DET_EN    =	MODE_AUTO_DET_PORT0 | MODE_AUTO_DET_PORT1 |
+				MODE_AUTO_DET_PORT2 | MODE_AUTO_DET_PORT3 |
+				MODE_AUTO_DET_PORT4 | MODE_AUTO_DET_PORT5 |
+				MODE_AUTO_DET_PORT6 | MODE_AUTO_DET_PORT7,
+	MODE_SAS_PORT7_MASK = (1U << 7),  /* port0 SAS(1), SATA(0) mode */
+	MODE_SAS_PORT6_MASK = (1U << 6),
+	MODE_SAS_PORT5_MASK = (1U << 5),
+	MODE_SAS_PORT4_MASK = (1U << 4),
+	MODE_SAS_PORT3_MASK = (1U << 3),
+	MODE_SAS_PORT2_MASK = (1U << 2),
+	MODE_SAS_PORT1_MASK = (1U << 1),
+	MODE_SAS_PORT0_MASK = (1U << 0),
+	MODE_SAS_SATA	=	MODE_SAS_PORT0_MASK | MODE_SAS_PORT1_MASK |
+				MODE_SAS_PORT2_MASK | MODE_SAS_PORT3_MASK |
+				MODE_SAS_PORT4_MASK | MODE_SAS_PORT5_MASK |
+				MODE_SAS_PORT6_MASK | MODE_SAS_PORT7_MASK,
+
+				/* SAS_MODE value may be
+				 * dictated (in hw) by values
+				 * of SATA_TARGET & AUTO_DET
+				 */
+
+	/* MVS_TX_CFG */
+	TX_EN			= (1U << 16),	/* Enable TX */
+	TX_RING_SZ_MASK		= 0xfff,	/* TX ring size, bits 11:0 */
+
+	/* MVS_RX_CFG */
+	RX_EN			= (1U << 16),	/* Enable RX */
+	RX_RING_SZ_MASK		= 0xfff,	/* RX ring size, bits 11:0 */
+
+	/* MVS_INT_COAL */
+	COAL_EN			= (1U << 16),	/* Enable int coalescing */
+
+	/* MVS_INT_STAT, MVS_INT_MASK */
+	CINT_I2C		= (1U << 31),	/* I2C event */
+	CINT_SW0		= (1U << 30),	/* software event 0 */
+	CINT_SW1		= (1U << 29),	/* software event 1 */
+	CINT_PRD_BC		= (1U << 28),	/* PRD BC err for read cmd */
+	CINT_DMA_PCIE		= (1U << 27),	/* DMA to PCIE timeout */
+	CINT_MEM		= (1U << 26),	/* int mem parity err */
+	CINT_I2C_SLAVE		= (1U << 25),	/* slave I2C event */
+	CINT_SRS		= (1U << 3),	/* SRS event */
+	CINT_CI_STOP		= (1U << 1),	/* cmd issue stopped */
+	CINT_DONE		= (1U << 0),	/* cmd completion */
+
+						/* shl for ports 1-3 */
+	CINT_PORT_STOPPED	= (1U << 16),	/* port0 stopped */
+	CINT_PORT		= (1U << 8),	/* port0 event */
+	CINT_PORT_MASK_OFFSET	= 8,
+	CINT_PORT_MASK		= (0xFF << CINT_PORT_MASK_OFFSET),
+
+	/* TX (delivery) ring bits */
+	TXQ_CMD_SHIFT		= 29,
+	TXQ_CMD_SSP		= 1,		/* SSP protocol */
+	TXQ_CMD_SMP		= 2,		/* SMP protocol */
+	TXQ_CMD_STP		= 3,		/* STP/SATA protocol */
+	TXQ_CMD_SSP_FREE_LIST	= 4,		/* add to SSP targ free list */
+	TXQ_CMD_SLOT_RESET	= 7,		/* reset command slot */
+	TXQ_MODE_I		= (1U << 28),	/* mode: 0=target,1=initiator */
+	TXQ_PRIO_HI		= (1U << 27),	/* priority: 0=normal, 1=high */
+	TXQ_SRS_SHIFT		= 20,		/* SATA register set */
+	TXQ_SRS_MASK		= 0x7f,
+	TXQ_PHY_SHIFT		= 12,		/* PHY bitmap */
+	TXQ_PHY_MASK		= 0xff,
+	TXQ_SLOT_MASK		= 0xfff,	/* slot number */
+
+	/* RX (completion) ring bits */
+	RXQ_GOOD		= (1U << 23),	/* Response good */
+	RXQ_SLOT_RESET		= (1U << 21),	/* Slot reset complete */
+	RXQ_CMD_RX		= (1U << 20),	/* target cmd received */
+	RXQ_ATTN		= (1U << 19),	/* attention */
+	RXQ_RSP			= (1U << 18),	/* response frame xfer'd */
+	RXQ_ERR			= (1U << 17),	/* err info rec xfer'd */
+	RXQ_DONE		= (1U << 16),	/* cmd complete */
+	RXQ_SLOT_MASK		= 0xfff,	/* slot number */
+
+	/* mvs_cmd_hdr bits */
+	MCH_PRD_LEN_SHIFT	= 16,		/* 16-bit PRD table len */
+	MCH_SSP_FR_TYPE_SHIFT	= 13,		/* SSP frame type */
+
+						/* SSP initiator only */
+	MCH_SSP_FR_CMD		= 0x0,		/* COMMAND frame */
+
+						/* SSP initiator or target */
+	MCH_SSP_FR_TASK		= 0x1,		/* TASK frame */
+
+						/* SSP target only */
+	MCH_SSP_FR_XFER_RDY	= 0x4,		/* XFER_RDY frame */
+	MCH_SSP_FR_RESP		= 0x5,		/* RESPONSE frame */
+	MCH_SSP_FR_READ		= 0x6,		/* Read DATA frame(s) */
+	MCH_SSP_FR_READ_RESP	= 0x7,		/* ditto, plus RESPONSE */
+
+	MCH_PASSTHRU		= (1U << 12),	/* pass-through (SSP) */
+	MCH_FBURST		= (1U << 11),	/* first burst (SSP) */
+	MCH_CHK_LEN		= (1U << 10),	/* chk xfer len (SSP) */
+	MCH_RETRY		= (1U << 9),	/* tport layer retry (SSP) */
+	MCH_PROTECTION		= (1U << 8),	/* protection info rec (SSP) */
+	MCH_RESET		= (1U << 7),	/* Reset (STP/SATA) */
+	MCH_FPDMA		= (1U << 6),	/* First party DMA (STP/SATA) */
+	MCH_ATAPI		= (1U << 5),	/* ATAPI (STP/SATA) */
+	MCH_BIST		= (1U << 4),	/* BIST activate (STP/SATA) */
+	MCH_PMP_MASK		= 0xf,		/* PMP from cmd FIS (STP/SATA)*/
+
+	CCTL_RST		= (1U << 5),	/* port logic reset */
+
+						/* 0(LSB first), 1(MSB first) */
+	CCTL_ENDIAN_DATA	= (1U << 3),	/* PRD data */
+	CCTL_ENDIAN_RSP		= (1U << 2),	/* response frame */
+	CCTL_ENDIAN_OPEN	= (1U << 1),	/* open address frame */
+	CCTL_ENDIAN_CMD		= (1U << 0),	/* command table */
+
+	/* MVS_Px_SER_CTLSTAT (per-phy control) */
+	PHY_SSP_RST		= (1U << 3),	/* reset SSP link layer */
+	PHY_BCAST_CHG		= (1U << 2),	/* broadcast(change) notif */
+	PHY_RST_HARD		= (1U << 1),	/* hard reset + phy reset */
+	PHY_RST			= (1U << 0),	/* phy reset */
+	PHY_MIN_SPP_PHYS_LINK_RATE_MASK = (0xF << 8),
+	PHY_MAX_SPP_PHYS_LINK_RATE_MASK = (0xF << 12),
+	PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET = (16),
+	PHY_NEG_SPP_PHYS_LINK_RATE_MASK =
+			(0xF << PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET),
+	PHY_READY_MASK		= (1U << 20),
+
+	/* MVS_Px_INT_STAT, MVS_Px_INT_MASK (per-phy events) */
+	PHYEV_DEC_ERR		= (1U << 24),	/* Phy Decoding Error */
+	PHYEV_UNASSOC_FIS	= (1U << 19),	/* unassociated FIS rx'd */
+	PHYEV_AN		= (1U << 18),	/* SATA async notification */
+	PHYEV_BIST_ACT		= (1U << 17),	/* BIST activate FIS */
+	PHYEV_SIG_FIS		= (1U << 16),	/* signature FIS */
+	PHYEV_POOF		= (1U << 12),	/* phy ready from 1 -> 0 */
+	PHYEV_IU_BIG		= (1U << 11),	/* IU too long err */
+	PHYEV_IU_SMALL		= (1U << 10),	/* IU too short err */
+	PHYEV_UNK_TAG		= (1U << 9),	/* unknown tag */
+	PHYEV_BROAD_CH		= (1U << 8),	/* broadcast(CHANGE) */
+	PHYEV_COMWAKE		= (1U << 7),	/* COMWAKE rx'd */
+	PHYEV_PORT_SEL		= (1U << 6),	/* port selector present */
+	PHYEV_HARD_RST		= (1U << 5),	/* hard reset rx'd */
+	PHYEV_ID_TMOUT		= (1U << 4),	/* identify timeout */
+	PHYEV_ID_FAIL		= (1U << 3),	/* identify failed */
+	PHYEV_ID_DONE		= (1U << 2),	/* identify done */
+	PHYEV_HARD_RST_DONE	= (1U << 1),	/* hard reset done */
+	PHYEV_RDY_CH		= (1U << 0),	/* phy ready changed state */
+
+	/* MVS_PCS */
+	PCS_EN_SATA_REG_SHIFT	= (16),		/* Enable SATA Register Set */
+	PCS_EN_PORT_XMT_SHIFT	= (12),		/* Enable Port Transmit */
+	PCS_EN_PORT_XMT_SHIFT2	= (8),		/* For 6480 */
+	PCS_SATA_RETRY		= (1U << 8),	/* retry ctl FIS on R_ERR */
+	PCS_RSP_RX_EN		= (1U << 7),	/* raw response rx */
+	PCS_SELF_CLEAR		= (1U << 5),	/* self-clearing int mode */
+	PCS_FIS_RX_EN		= (1U << 4),	/* FIS rx enable */
+	PCS_CMD_STOP_ERR	= (1U << 3),	/* cmd stop-on-err enable */
+	PCS_CMD_RST		= (1U << 1),	/* reset cmd issue */
+	PCS_CMD_EN		= (1U << 0),	/* enable cmd issue */
+
+	/* Port n Attached Device Info */
+	PORT_DEV_SSP_TRGT	= (1U << 19),
+	PORT_DEV_SMP_TRGT	= (1U << 18),
+	PORT_DEV_STP_TRGT	= (1U << 17),
+	PORT_DEV_SSP_INIT	= (1U << 11),
+	PORT_DEV_SMP_INIT	= (1U << 10),
+	PORT_DEV_STP_INIT	= (1U << 9),
+	PORT_PHY_ID_MASK	= (0xFFU << 24),
+	PORT_DEV_TRGT_MASK	= (0x7U << 17),
+	PORT_DEV_INIT_MASK	= (0x7U << 9),
+	PORT_DEV_TYPE_MASK	= (0x7U << 0),
+
+	/* Port n PHY Status */
+	PHY_RDY			= (1U << 2),
+	PHY_DW_SYNC		= (1U << 1),
+	PHY_OOB_DTCTD		= (1U << 0),
+
+	/* VSR */
+	/* PHYMODE 6 (CDB) */
+	PHY_MODE6_LATECLK	= (1U << 29),	/* Lock Clock */
+	PHY_MODE6_DTL_SPEED	= (1U << 27),	/* Digital Loop Speed */
+	PHY_MODE6_FC_ORDER	= (1U << 26),	/* Fibre Channel Mode Order*/
+	PHY_MODE6_MUCNT_EN	= (1U << 24),	/* u Count Enable */
+	PHY_MODE6_SEL_MUCNT_LEN	= (1U << 22),	/* Training Length Select */
+	PHY_MODE6_SELMUPI	= (1U << 20),	/* Phase Multi Select (init) */
+	PHY_MODE6_SELMUPF	= (1U << 18),	/* Phase Multi Select (final) */
+	PHY_MODE6_SELMUFF	= (1U << 16),	/* Freq Loop Multi Sel(final) */
+	PHY_MODE6_SELMUFI	= (1U << 14),	/* Freq Loop Multi Sel(init) */
+	PHY_MODE6_FREEZE_LOOP	= (1U << 12),	/* Freeze Rx CDR Loop */
+	PHY_MODE6_INT_RXFOFFS	= (1U << 3),	/* Rx CDR Freq Loop Enable */
+	PHY_MODE6_FRC_RXFOFFS	= (1U << 2),	/* Initial Rx CDR Offset */
+	PHY_MODE6_STAU_0D8	= (1U << 1),	/* Rx CDR Freq Loop Saturate */
+	PHY_MODE6_RXSAT_DIS	= (1U << 0),	/* Saturate Ctl */
+};
+
+/* SAS/SATA configuration port registers, aka phy registers */
+enum sas_sata_config_port_regs {
+	PHYR_IDENTIFY		= 0x00,	/* info for IDENTIFY frame */
+	PHYR_ADDR_LO		= 0x04,	/* my SAS address (low) */
+	PHYR_ADDR_HI		= 0x08,	/* my SAS address (high) */
+	PHYR_ATT_DEV_INFO	= 0x0C,	/* attached device info */
+	PHYR_ATT_ADDR_LO	= 0x10,	/* attached dev SAS addr (low) */
+	PHYR_ATT_ADDR_HI	= 0x14,	/* attached dev SAS addr (high) */
+	PHYR_SATA_CTL		= 0x18,	/* SATA control */
+	PHYR_PHY_STAT		= 0x1C,	/* PHY status */
+	PHYR_SATA_SIG0		= 0x20,	/*port SATA signature FIS(Byte 0-3) */
+	PHYR_SATA_SIG1		= 0x24,	/*port SATA signature FIS(Byte 4-7) */
+	PHYR_SATA_SIG2		= 0x28,	/*port SATA signature FIS(Byte 8-11) */
+	PHYR_SATA_SIG3		= 0x2c,	/*port SATA signature FIS(Byte 12-15) */
+	PHYR_R_ERR_COUNT	= 0x30, /* port R_ERR count register */
+	PHYR_CRC_ERR_COUNT	= 0x34, /* port CRC error count register */
+	PHYR_WIDE_PORT		= 0x38,	/* wide port participating */
+	PHYR_CURRENT0		= 0x80,	/* current connection info 0 */
+	PHYR_CURRENT1		= 0x84,	/* current connection info 1 */
+	PHYR_CURRENT2		= 0x88,	/* current connection info 2 */
+};
+
+enum mvs_info_flags {
+	MVF_MSI			= (1U << 0),	/* MSI is enabled */
+	MVF_PHY_PWR_FIX		= (1U << 1),	/* bug workaround */
+};
+
+enum sas_cmd_port_registers {
+	CMD_CMRST_OOB_DET	= 0x100, /* COMRESET OOB detect register */
+	CMD_CMWK_OOB_DET	= 0x104, /* COMWAKE OOB detect register */
+	CMD_CMSAS_OOB_DET	= 0x108, /* COMSAS OOB detect register */
+	CMD_BRST_OOB_DET	= 0x10c, /* burst OOB detect register */
+	CMD_OOB_SPACE		= 0x110, /* OOB space control register */
+	CMD_OOB_BURST		= 0x114, /* OOB burst control register */
+	CMD_PHY_TIMER		= 0x118, /* PHY timer control register */
+	CMD_PHY_CONFIG0		= 0x11c, /* PHY config register 0 */
+	CMD_PHY_CONFIG1		= 0x120, /* PHY config register 1 */
+	CMD_SAS_CTL0		= 0x124, /* SAS control register 0 */
+	CMD_SAS_CTL1		= 0x128, /* SAS control register 1 */
+	CMD_SAS_CTL2		= 0x12c, /* SAS control register 2 */
+	CMD_SAS_CTL3		= 0x130, /* SAS control register 3 */
+	CMD_ID_TEST		= 0x134, /* ID test register */
+	CMD_PL_TIMER		= 0x138, /* PL timer register */
+	CMD_WD_TIMER		= 0x13c, /* WD timer register */
+	CMD_PORT_SEL_COUNT	= 0x140, /* port selector count register */
+	CMD_APP_MEM_CTL		= 0x144, /* Application Memory Control */
+	CMD_XOR_MEM_CTL		= 0x148, /* XOR Block Memory Control */
+	CMD_DMA_MEM_CTL		= 0x14c, /* DMA Block Memory Control */
+	CMD_PORT_MEM_CTL0	= 0x150, /* Port Memory Control 0 */
+	CMD_PORT_MEM_CTL1	= 0x154, /* Port Memory Control 1 */
+	CMD_SATA_PORT_MEM_CTL0	= 0x158, /* SATA Port Memory Control 0 */
+	CMD_SATA_PORT_MEM_CTL1	= 0x15c, /* SATA Port Memory Control 1 */
+	CMD_XOR_MEM_BIST_CTL	= 0x160, /* XOR Memory BIST Control */
+	CMD_XOR_MEM_BIST_STAT	= 0x164, /* XOR Memroy BIST Status */
+	CMD_DMA_MEM_BIST_CTL	= 0x168, /* DMA Memory BIST Control */
+	CMD_DMA_MEM_BIST_STAT	= 0x16c, /* DMA Memory BIST Status */
+	CMD_PORT_MEM_BIST_CTL	= 0x170, /* Port Memory BIST Control */
+	CMD_PORT_MEM_BIST_STAT0 = 0x174, /* Port Memory BIST Status 0 */
+	CMD_PORT_MEM_BIST_STAT1 = 0x178, /* Port Memory BIST Status 1 */
+	CMD_STP_MEM_BIST_CTL	= 0x17c, /* STP Memory BIST Control */
+	CMD_STP_MEM_BIST_STAT0	= 0x180, /* STP Memory BIST Status 0 */
+	CMD_STP_MEM_BIST_STAT1	= 0x184, /* STP Memory BIST Status 1 */
+	CMD_RESET_COUNT		= 0x188, /* Reset Count */
+	CMD_MONTR_DATA_SEL	= 0x18C, /* Monitor Data/Select */
+	CMD_PLL_PHY_CONFIG	= 0x190, /* PLL/PHY Configuration */
+	CMD_PHY_CTL		= 0x194, /* PHY Control and Status */
+	CMD_PHY_TEST_COUNT0	= 0x198, /* Phy Test Count 0 */
+	CMD_PHY_TEST_COUNT1	= 0x19C, /* Phy Test Count 1 */
+	CMD_PHY_TEST_COUNT2	= 0x1A0, /* Phy Test Count 2 */
+	CMD_APP_ERR_CONFIG	= 0x1A4, /* Application Error Configuration */
+	CMD_PND_FIFO_CTL0	= 0x1A8, /* Pending FIFO Control 0 */
+	CMD_HOST_CTL		= 0x1AC, /* Host Control Status */
+	CMD_HOST_WR_DATA	= 0x1B0, /* Host Write Data */
+	CMD_HOST_RD_DATA	= 0x1B4, /* Host Read Data */
+	CMD_PHY_MODE_21		= 0x1B8, /* Phy Mode 21 */
+	CMD_SL_MODE0		= 0x1BC, /* SL Mode 0 */
+	CMD_SL_MODE1		= 0x1C0, /* SL Mode 1 */
+	CMD_PND_FIFO_CTL1	= 0x1C4, /* Pending FIFO Control 1 */
+};
+
+enum pci_cfg_register_bits {
+	PCTL_PWR_ON	= (0xFU << 24),
+	PCTL_OFF	= (0xFU << 12),
+	PRD_REQ_SIZE	= (0x4000),
+	PRD_REQ_MASK	= (0x00007000),
+};
+
+enum nvram_layout_offsets {
+	NVR_SIG		= 0x00,		/* 0xAA, 0x55 */
+	NVR_SAS_ADDR	= 0x02,		/* 8-byte SAS address */
+};
+
+enum chip_flavors {
+	chip_6320,
+	chip_6440,
+	chip_6480,
+};
+
+enum port_type {
+	PORT_TYPE_SAS	=  (1L << 1),
+	PORT_TYPE_SATA	=  (1L << 0),
+};
+
+/* Command Table Format */
+enum ct_format {
+	/* SSP */
+	SSP_F_H		=  0x00,
+	SSP_F_IU	=  0x18,
+	SSP_F_MAX	=  0x4D,
+	/* STP */
+	STP_CMD_FIS	=  0x00,
+	STP_ATAPI_CMD	=  0x40,
+	STP_F_MAX	=  0x10,
+	/* SMP */
+	SMP_F_T		=  0x00,
+	SMP_F_DEP	=  0x01,
+	SMP_F_MAX	=  0x101,
+};
+
+enum status_buffer {
+	SB_EIR_OFF	=  0x00,	/* Error Information Record */
+	SB_RFB_OFF	=  0x08,	/* Response Frame Buffer */
+	SB_RFB_MAX	=  0x400,	/* RFB size*/
+};
+
+enum error_info_rec {
+	CMD_ISS_STPD	= (1U << 31),	/* Cmd Issue Stopped */
+	CMD_PI_ERR	= (1U << 30),	/* Protection info error.  see flags2 */
+	RSP_OVER	= (1U << 29),	/* rsp buffer overflow */
+	RETRY_LIM	= (1U << 28),	/* FIS/frame retry limit exceeded */
+	UNK_FIS 	= (1U << 27),	/* unknown FIS */
+	DMA_TERM	= (1U << 26),	/* DMA terminate primitive rx'd */
+	SYNC_ERR	= (1U << 25),	/* SYNC rx'd during frame xmit */
+	TFILE_ERR	= (1U << 24),	/* SATA taskfile Error bit set */
+	R_ERR		= (1U << 23),	/* SATA returned R_ERR prim */
+	RD_OFS		= (1U << 20),	/* Read DATA frame invalid offset */
+	XFER_RDY_OFS	= (1U << 19),	/* XFER_RDY offset error */
+	UNEXP_XFER_RDY	= (1U << 18),	/* unexpected XFER_RDY error */
+	DATA_OVER_UNDER = (1U << 16),	/* data overflow/underflow */
+	INTERLOCK	= (1U << 15),	/* interlock error */
+	NAK		= (1U << 14),	/* NAK rx'd */
+	ACK_NAK_TO	= (1U << 13),	/* ACK/NAK timeout */
+	CXN_CLOSED	= (1U << 12),	/* cxn closed w/out ack/nak */
+	OPEN_TO 	= (1U << 11),	/* I_T nexus lost, open cxn timeout */
+	PATH_BLOCKED	= (1U << 10),	/* I_T nexus lost, pathway blocked */
+	NO_DEST 	= (1U << 9),	/* I_T nexus lost, no destination */
+	STP_RES_BSY	= (1U << 8),	/* STP resources busy */
+	BREAK		= (1U << 7),	/* break received */
+	BAD_DEST	= (1U << 6),	/* bad destination */
+	BAD_PROTO	= (1U << 5),	/* protocol not supported */
+	BAD_RATE	= (1U << 4),	/* cxn rate not supported */
+	WRONG_DEST	= (1U << 3),	/* wrong destination error */
+	CREDIT_TO	= (1U << 2),	/* credit timeout */
+	WDOG_TO 	= (1U << 1),	/* watchdog timeout */
+	BUF_PAR 	= (1U << 0),	/* buffer parity error */
+};
+
+enum error_info_rec_2 {
+	SLOT_BSY_ERR	= (1U << 31),	/* Slot Busy Error */
+	GRD_CHK_ERR	= (1U << 14),	/* Guard Check Error */
+	APP_CHK_ERR	= (1U << 13),	/* Application Check error */
+	REF_CHK_ERR	= (1U << 12),	/* Reference Check Error */
+	USR_BLK_NM	= (1U << 0),	/* User Block Number */
+};
+
+#endif