Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
  [SCSI] usbstorage: use last_sector_bug flag universally
  [SCSI] libsas: abstract STP task status into a function
  [SCSI] ultrastor: clean up inline asm warnings
  [SCSI] aic7xxx: fix firmware build
  [SCSI] aacraid: fib context lock for management ioctls
  [SCSI] ch: remove forward declarations
  [SCSI] ch: fix device minor number management bug
  [SCSI] ch: handle class_device_create failure properly
  [SCSI] NCR5380: fix section mismatch
  [SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
  [SCSI] IB/iSER: add logical unit reset support
  [SCSI] don't use __GFP_DMA for sense buffers if not required
  [SCSI] use dynamically allocated sense buffer
  [SCSI] scsi.h: add macro for enclosure bit of inquiry data
  [SCSI] sd: add fix for devices with last sector access problems
  [SCSI] fix pcmcia compile problem
  [SCSI] aacraid: add Voodoo Lite class of cards.
  [SCSI] aacraid: add new driver features flags
  [SCSI] qla2xxx: Update version number to 8.02.00-k7.
  [SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
  ...

1 files changed, 0 insertions, 1667 deletions

diff --git a/drivers/scsi/seagate.c b/drivers/scsi/seagate.c
deleted file mode 100644
index b11324479b5..00000000000
--- a/drivers/scsi/seagate.c
+++ /dev/null
@@ -1,1667 +0,0 @@
-/*
- *    seagate.c Copyright (C) 1992, 1993 Drew Eckhardt
- *      low level scsi driver for ST01/ST02, Future Domain TMC-885,
- *      TMC-950 by Drew Eckhardt <drew@colorado.edu>
- *
- *      Note : TMC-880 boards don't work because they have two bits in
- *              the status register flipped, I'll fix this "RSN"
- *	[why do I have strong feeling that above message is from 1993? :-)
- *	        pavel@ucw.cz]
- *
- *      This card does all the I/O via memory mapped I/O, so there is no need
- *      to check or allocate a region of the I/O address space.
- */
-
-/* 1996 - to use new read{b,w,l}, write{b,w,l}, and phys_to_virt
- * macros, replaced assembler routines with C. There's probably a
- * performance hit, but I only have a cdrom and can't tell. Define
- * SEAGATE_USE_ASM if you want the old assembler code -- SJT
- *
- * 1998-jul-29 - created DPRINTK macros and made it work under 
- * linux 2.1.112, simplified some #defines etc. <pavel@ucw.cz>
- *
- * Aug 2000 - aeb - deleted seagate_st0x_biosparam(). It would try to
- * read the physical disk geometry, a bad mistake. Of course it doesn't
- * matter much what geometry one invents, but on large disks it
- * returned 256 (or more) heads, causing all kind of failures.
- * Of course this means that people might see a different geometry now,
- * so boot parameters may be necessary in some cases.
- */
-
-/*
- * Configuration :
- * To use without BIOS -DOVERRIDE=base_address -DCONTROLLER=FD or SEAGATE
- * -DIRQ will override the default of 5.
- * Note: You can now set these options from the kernel's "command line".
- * The syntax is:
- *
- *     st0x=ADDRESS,IRQ                (for a Seagate controller)
- * or:
- *     tmc8xx=ADDRESS,IRQ              (for a TMC-8xx or TMC-950 controller)
- * eg:
- *     tmc8xx=0xC8000,15
- *
- * will configure the driver for a TMC-8xx style controller using IRQ 15
- * with a base address of 0xC8000.
- *
- * -DARBITRATE 
- *      Will cause the host adapter to arbitrate for the
- *      bus for better SCSI-II compatibility, rather than just
- *      waiting for BUS FREE and then doing its thing.  Should
- *      let us do one command per Lun when I integrate my
- *      reorganization changes into the distribution sources.
- *
- * -DDEBUG=65535
- *      Will activate debug code.
- *
- * -DFAST or -DFAST32 
- *      Will use blind transfers where possible
- *
- * -DPARITY  
- *      This will enable parity.
- *
- * -DSEAGATE_USE_ASM
- *      Will use older seagate assembly code. should be (very small amount)
- *      Faster.
- *
- * -DSLOW_RATE=50
- *      Will allow compatibility with broken devices that don't
- *      handshake fast enough (ie, some CD ROM's) for the Seagate
- *      code.
- *
- *      50 is some number, It will let you specify a default
- *      transfer rate if handshaking isn't working correctly.
- *
- * -DOLDCNTDATASCEME  There is a new sceme to set the CONTROL
- *                    and DATA reigsters which complies more closely
- *                    with the SCSI2 standard. This hopefully eliminates
- *                    the need to swap the order these registers are
- *                    'messed' with. It makes the following two options
- *                    obsolete. To reenable the old sceme define this.
- *
- * The following to options are patches from the SCSI.HOWTO
- *
- * -DSWAPSTAT  This will swap the definitions for STAT_MSG and STAT_CD.
- *
- * -DSWAPCNTDATA  This will swap the order that seagate.c messes with
- *                the CONTROL an DATA registers.
- */
-
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/signal.h>
-#include <linux/string.h>
-#include <linux/proc_fs.h>
-#include <linux/init.h>
-#include <linux/blkdev.h>
-#include <linux/stat.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-
-#include <asm/system.h>
-#include <asm/uaccess.h>
-
-#include <scsi/scsi_cmnd.h>
-#include <scsi/scsi_device.h>
-#include <scsi/scsi.h>
-
-#include <scsi/scsi_dbg.h>
-#include <scsi/scsi_host.h>
-
-
-#ifdef DEBUG
-#define DPRINTK( when, msg... ) do { if ( (DEBUG & (when)) == (when) ) printk( msg ); } while (0)
-#else
-#define DPRINTK( when, msg... ) do { } while (0)
-#define DEBUG 0
-#endif
-#define DANY( msg... ) DPRINTK( 0xffff, msg );
-
-#ifndef IRQ
-#define IRQ 5
-#endif
-
-#ifdef FAST32
-#define FAST
-#endif
-
-#undef LINKED			/* Linked commands are currently broken! */
-
-#if defined(OVERRIDE) && !defined(CONTROLLER)
-#error Please use -DCONTROLLER=SEAGATE or -DCONTROLLER=FD to override controller type
-#endif
-
-#ifndef __i386__
-#undef SEAGATE_USE_ASM
-#endif
-
-/*
-	Thanks to Brian Antoine for the example code in his Messy-Loss ST-01
-		driver, and Mitsugu Suzuki for information on the ST-01
-		SCSI host.
-*/
-
-/*
-	CONTROL defines
-*/
-
-#define CMD_RST 		0x01
-#define CMD_SEL 		0x02
-#define CMD_BSY 		0x04
-#define CMD_ATTN    		0x08
-#define CMD_START_ARB		0x10
-#define CMD_EN_PARITY		0x20
-#define CMD_INTR		0x40
-#define CMD_DRVR_ENABLE		0x80
-
-/*
-	STATUS
-*/
-#ifdef SWAPSTAT
-#define STAT_MSG		0x08
-#define STAT_CD			0x02
-#else
-#define STAT_MSG		0x02
-#define STAT_CD			0x08
-#endif
-
-#define STAT_BSY		0x01
-#define STAT_IO			0x04
-#define STAT_REQ		0x10
-#define STAT_SEL		0x20
-#define STAT_PARITY		0x40
-#define STAT_ARB_CMPL		0x80
-
-/* 
-	REQUESTS
-*/
-
-#define REQ_MASK (STAT_CD |  STAT_IO | STAT_MSG)
-#define REQ_DATAOUT 0
-#define REQ_DATAIN STAT_IO
-#define REQ_CMDOUT STAT_CD
-#define REQ_STATIN (STAT_CD | STAT_IO)
-#define REQ_MSGOUT (STAT_MSG | STAT_CD)
-#define REQ_MSGIN (STAT_MSG | STAT_CD | STAT_IO)
-
-extern volatile int seagate_st0x_timeout;
-
-#ifdef PARITY
-#define BASE_CMD CMD_EN_PARITY
-#else
-#define BASE_CMD  0
-#endif
-
-/*
-	Debugging code
-*/
-
-#define PHASE_BUS_FREE 1
-#define PHASE_ARBITRATION 2
-#define PHASE_SELECTION 4
-#define PHASE_DATAIN 8
-#define PHASE_DATAOUT 0x10
-#define PHASE_CMDOUT 0x20
-#define PHASE_MSGIN 0x40
-#define PHASE_MSGOUT 0x80
-#define PHASE_STATUSIN 0x100
-#define PHASE_ETC (PHASE_DATAIN | PHASE_DATAOUT | PHASE_CMDOUT | PHASE_MSGIN | PHASE_MSGOUT | PHASE_STATUSIN)
-#define PRINT_COMMAND 0x200
-#define PHASE_EXIT 0x400
-#define PHASE_RESELECT 0x800
-#define DEBUG_FAST 0x1000
-#define DEBUG_SG   0x2000
-#define DEBUG_LINKED	0x4000
-#define DEBUG_BORKEN	0x8000
-
-/* 
- *	Control options - these are timeouts specified in .01 seconds.
- */
-
-/* 30, 20 work */
-#define ST0X_BUS_FREE_DELAY 25
-#define ST0X_SELECTION_DELAY 25
-
-#define SEAGATE 1		/* these determine the type of the controller */
-#define FD	2
-
-#define ST0X_ID_STR	"Seagate ST-01/ST-02"
-#define FD_ID_STR	"TMC-8XX/TMC-950"
-
-static int internal_command (unsigned char target, unsigned char lun,
-			     const void *cmnd,
-			     void *buff, int bufflen, int reselect);
-
-static int incommand;		/* set if arbitration has finished
-				   and we are in some command phase. */
-
-static unsigned int base_address = 0;	/* Where the card ROM starts, used to 
-					   calculate memory mapped register
-					   location.  */
-
-static void __iomem *st0x_cr_sr;	/* control register write, status
-					   register read.  256 bytes in
-					   length.
-					   Read is status of SCSI BUS, as per 
-					   STAT masks.  */
-
-static void __iomem *st0x_dr;	/* data register, read write 256
-				   bytes in length.  */
-
-static volatile int st0x_aborted = 0;	/* set when we are aborted, ie by a
-					   time out, etc.  */
-
-static unsigned char controller_type = 0;	/* set to SEAGATE for ST0x
-						   boards or FD for TMC-8xx
-						   boards */
-static int irq = IRQ;
-
-module_param(base_address, uint, 0);
-module_param(controller_type, byte, 0);
-module_param(irq, int, 0);
-MODULE_LICENSE("GPL");
-
-
-#define retcode(result) (((result) << 16) | (message << 8) | status)
-#define STATUS ((u8) readb(st0x_cr_sr))
-#define DATA ((u8) readb(st0x_dr))
-#define WRITE_CONTROL(d) { writeb((d), st0x_cr_sr); }
-#define WRITE_DATA(d) { writeb((d), st0x_dr); }
-
-#ifndef OVERRIDE
-static unsigned int seagate_bases[] = {
-	0xc8000, 0xca000, 0xcc000,
-	0xce000, 0xdc000, 0xde000
-};
-
-typedef struct {
-	const unsigned char *signature;
-	unsigned offset;
-	unsigned length;
-	unsigned char type;
-} Signature;
-
-static Signature __initdata signatures[] = {
-	{"ST01 v1.7  (C) Copyright 1987 Seagate", 15, 37, SEAGATE},
-	{"SCSI BIOS 2.00  (C) Copyright 1987 Seagate", 15, 40, SEAGATE},
-
-/*
- * The following two lines are NOT mistakes.  One detects ROM revision
- * 3.0.0, the other 3.2.  Since seagate has only one type of SCSI adapter,
- * and this is not going to change, the "SEAGATE" and "SCSI" together
- * are probably "good enough"
- */
-
-	{"SEAGATE SCSI BIOS ", 16, 17, SEAGATE},
-	{"SEAGATE SCSI BIOS ", 17, 17, SEAGATE},
-
-/*
- * However, future domain makes several incompatible SCSI boards, so specific
- * signatures must be used.
- */
-
-	{"FUTURE DOMAIN CORP. (C) 1986-1989 V5.0C2/14/89", 5, 46, FD},
-	{"FUTURE DOMAIN CORP. (C) 1986-1989 V6.0A7/28/89", 5, 46, FD},
-	{"FUTURE DOMAIN CORP. (C) 1986-1990 V6.0105/31/90", 5, 47, FD},
-	{"FUTURE DOMAIN CORP. (C) 1986-1990 V6.0209/18/90", 5, 47, FD},
-	{"FUTURE DOMAIN CORP. (C) 1986-1990 V7.009/18/90", 5, 46, FD},
-	{"FUTURE DOMAIN CORP. (C) 1992 V8.00.004/02/92", 5, 44, FD},
-	{"IBM F1 BIOS V1.1004/30/92", 5, 25, FD},
-	{"FUTURE DOMAIN TMC-950", 5, 21, FD},
-	/* Added for 2.2.16 by Matthias_Heidbrink@b.maus.de */
-	{"IBM F1 V1.2009/22/93", 5, 25, FD},
-};
-
-#define NUM_SIGNATURES ARRAY_SIZE(signatures)
-#endif				/* n OVERRIDE */
-
-/*
- * hostno stores the hostnumber, as told to us by the init routine.
- */
-
-static int hostno = -1;
-static void seagate_reconnect_intr (int, void *);
-static irqreturn_t do_seagate_reconnect_intr (int, void *);
-static int seagate_st0x_bus_reset(struct scsi_cmnd *);
-
-#ifdef FAST
-static int fast = 1;
-#else
-#define fast 0
-#endif
-
-#ifdef SLOW_RATE
-/*
- * Support for broken devices :
- * The Seagate board has a handshaking problem.  Namely, a lack
- * thereof for slow devices.  You can blast 600K/second through
- * it if you are polling for each byte, more if you do a blind
- * transfer.  In the first case, with a fast device, REQ will
- * transition high-low or high-low-high before your loop restarts
- * and you'll have no problems.  In the second case, the board
- * will insert wait states for up to 13.2 usecs for REQ to
- * transition low->high, and everything will work.
- *
- * However, there's nothing in the state machine that says
- * you *HAVE* to see a high-low-high set of transitions before
- * sending the next byte, and slow things like the Trantor CD ROMS
- * will break because of this.
- *
- * So, we need to slow things down, which isn't as simple as it
- * seems.  We can't slow things down period, because then people
- * who don't recompile their kernels will shoot me for ruining
- * their performance.  We need to do it on a case per case basis.
- *
- * The best for performance will be to, only for borken devices
- * (this is stored on a per-target basis in the scsi_devices array)
- *
- * Wait for a low->high transition before continuing with that
- * transfer.  If we timeout, continue anyways.  We don't need
- * a long timeout, because REQ should only be asserted until the
- * corresponding ACK is received and processed.
- *
- * Note that we can't use the system timer for this, because of
- * resolution, and we *really* can't use the timer chip since
- * gettimeofday() and the beeper routines use that.  So,
- * the best thing for us to do will be to calibrate a timing
- * loop in the initialization code using the timer chip before
- * gettimeofday() can screw with it.
- *
- * FIXME: this is broken (not borken :-). Empty loop costs less than
- * loop with ISA access in it! -- pavel@ucw.cz
- */
-
-static int borken_calibration = 0;
-
-static void __init borken_init (void)
-{
-	register int count = 0, start = jiffies + 1, stop = start + 25;
-
-	/* FIXME: There may be a better approach, this is a straight port for
-	   now */
-	preempt_disable();
-	while (time_before (jiffies, start))
-		cpu_relax();
-	for (; time_before (jiffies, stop); ++count)
-		cpu_relax();
-	preempt_enable();
-
-/*
- * Ok, we now have a count for .25 seconds.  Convert to a
- * count per second and divide by transfer rate in K.  */
-
-	borken_calibration = (count * 4) / (SLOW_RATE * 1024);
-
-	if (borken_calibration < 1)
-		borken_calibration = 1;
-}
-
-static inline void borken_wait (void)
-{
-	register int count;
-
-	for (count = borken_calibration; count && (STATUS & STAT_REQ); --count)
-		cpu_relax();
-	     	
-#if (DEBUG & DEBUG_BORKEN)
-	if (count)
-		printk ("scsi%d : borken timeout\n", hostno);
-#endif
-}
-
-#endif				/* def SLOW_RATE */
-
-/* These beasts only live on ISA, and ISA means 8MHz. Each ULOOP()
- * contains at least one ISA access, which takes more than 0.125
- * usec. So if we loop 8 times time in usec, we are safe.
- */
-
-#define ULOOP( i ) for (clock = i*8;;)
-#define TIMEOUT (!(clock--))
-
-static int __init seagate_st0x_detect (struct scsi_host_template * tpnt)
-{
-	struct Scsi_Host *instance;
-	int i, j;
-	unsigned long cr, dr;
-
-	tpnt->proc_name = "seagate";
-/*
- *	First, we try for the manual override.
- */
-	DANY ("Autodetecting ST0x / TMC-8xx\n");
-
-	if (hostno != -1) {
-		printk (KERN_ERR "seagate_st0x_detect() called twice?!\n");
-		return 0;
-	}
-
-/* If the user specified the controller type from the command line,
-   controller_type will be non-zero, so don't try to detect one */
-
-	if (!controller_type) {
-#ifdef OVERRIDE
-		base_address = OVERRIDE;
-		controller_type = CONTROLLER;
-
-		DANY ("Base address overridden to %x, controller type is %s\n",
-		      base_address,
-		      controller_type == SEAGATE ? "SEAGATE" : "FD");
-#else				/* OVERRIDE */
-/*
- * 	To detect this card, we simply look for the signature
- *      from the BIOS version notice in all the possible locations
- *      of the ROM's.  This has a nice side effect of not trashing
- *      any register locations that might be used by something else.
- *
- * XXX - note that we probably should be probing the address
- * space for the on-board RAM instead.
- */
-
-		for (i = 0; i < ARRAY_SIZE(seagate_bases); ++i) {
-			void __iomem *p = ioremap(seagate_bases[i], 0x2000);
-			if (!p)
-				continue;
-			for (j = 0; j < NUM_SIGNATURES; ++j)
-				if (check_signature(p + signatures[j].offset, signatures[j].signature, signatures[j].length)) {
-					base_address = seagate_bases[i];
-					controller_type = signatures[j].type;
-					break;
-				}
-			iounmap(p);
-		}
-#endif				/* OVERRIDE */
-	}
-	/* (! controller_type) */
-	tpnt->this_id = (controller_type == SEAGATE) ? 7 : 6;
-	tpnt->name = (controller_type == SEAGATE) ? ST0X_ID_STR : FD_ID_STR;
-
-	if (!base_address) {
-		printk(KERN_INFO "seagate: ST0x/TMC-8xx not detected.\n");
-		return 0;
-	}
-
-	cr = base_address + (controller_type == SEAGATE ? 0x1a00 : 0x1c00);
-	dr = cr + 0x200;
-	st0x_cr_sr = ioremap(cr, 0x100);
-	st0x_dr = ioremap(dr, 0x100);
-
-	DANY("%s detected. Base address = %x, cr = %x, dr = %x\n",
-	      tpnt->name, base_address, cr, dr);
-
-	/*
-	 *	At all times, we will use IRQ 5.  Should also check for IRQ3
-	 *	if we lose our first interrupt.
-	 */
-	instance = scsi_register (tpnt, 0);
-	if (instance == NULL)
-		return 0;
-
-	hostno = instance->host_no;
-	if (request_irq (irq, do_seagate_reconnect_intr, IRQF_DISABLED, (controller_type == SEAGATE) ? "seagate" : "tmc-8xx", instance)) {
-		printk(KERN_ERR "scsi%d : unable to allocate IRQ%d\n", hostno, irq);
-		return 0;
-	}
-	instance->irq = irq;
-	instance->io_port = base_address;
-#ifdef SLOW_RATE
-	printk(KERN_INFO "Calibrating borken timer... ");
-	borken_init();
-	printk(" %d cycles per transfer\n", borken_calibration);
-#endif
-	printk (KERN_INFO "This is one second... ");
-	{
-		int clock;
-		ULOOP (1 * 1000 * 1000) {
-			STATUS;
-			if (TIMEOUT)
-				break;
-		}
-	}
-
-	printk ("done, %s options:"
-#ifdef ARBITRATE
-		" ARBITRATE"
-#endif
-#if DEBUG
-		" DEBUG"
-#endif
-#ifdef FAST
-		" FAST"
-#ifdef FAST32
-		"32"
-#endif
-#endif
-#ifdef LINKED
-		" LINKED"
-#endif
-#ifdef PARITY
-		" PARITY"
-#endif
-#ifdef SEAGATE_USE_ASM
-		" SEAGATE_USE_ASM"
-#endif
-#ifdef SLOW_RATE
-		" SLOW_RATE"
-#endif
-#ifdef SWAPSTAT
-		" SWAPSTAT"
-#endif
-#ifdef SWAPCNTDATA
-		" SWAPCNTDATA"
-#endif
-		"\n", tpnt->name);
-	return 1;
-}
-
-static const char *seagate_st0x_info (struct Scsi_Host *shpnt)
-{
-	static char buffer[64];
-
-	snprintf(buffer, 64, "%s at irq %d, address 0x%05X",
-		 (controller_type == SEAGATE) ? ST0X_ID_STR : FD_ID_STR,
-		 irq, base_address);
-	return buffer;
-}
-
-/*
- * These are our saved pointers for the outstanding command that is
- * waiting for a reconnect
- */
-
-static unsigned char current_target, current_lun;
-static unsigned char *current_cmnd, *current_data;
-static int current_nobuffs;
-static struct scatterlist *current_buffer;
-static int current_bufflen;
-
-#ifdef LINKED
-/*
- * linked_connected indicates whether or not we are currently connected to
- * linked_target, linked_lun and in an INFORMATION TRANSFER phase,
- * using linked commands.
- */
-
-static int linked_connected = 0;
-static unsigned char linked_target, linked_lun;
-#endif
-
-static void (*done_fn) (struct scsi_cmnd *) = NULL;
-static struct scsi_cmnd *SCint = NULL;
-
-/*
- * These control whether or not disconnect / reconnect will be attempted,
- * or are being attempted.
- */
-
-#define NO_RECONNECT    0
-#define RECONNECT_NOW   1
-#define CAN_RECONNECT   2
-
-/*
- * LINKED_RIGHT indicates that we are currently connected to the correct target
- * for this command, LINKED_WRONG indicates that we are connected to the wrong
- * target. Note that these imply CAN_RECONNECT and require defined(LINKED).
- */
-
-#define LINKED_RIGHT    3
-#define LINKED_WRONG    4
-
-/*
- * This determines if we are expecting to reconnect or not.
- */
-
-static int should_reconnect = 0;
-
-/*
- * The seagate_reconnect_intr routine is called when a target reselects the
- * host adapter.  This occurs on the interrupt triggered by the target
- * asserting SEL.
- */
-
-static irqreturn_t do_seagate_reconnect_intr(int irq, void *dev_id)
-{
-	unsigned long flags;
-	struct Scsi_Host *dev = dev_id;
-	
-	spin_lock_irqsave (dev->host_lock, flags);
-	seagate_reconnect_intr (irq, dev_id);
-	spin_unlock_irqrestore (dev->host_lock, flags);
-	return IRQ_HANDLED;
-}
-
-static void seagate_reconnect_intr (int irq, void *dev_id)
-{
-	int temp;
-	struct scsi_cmnd *SCtmp;
-
-	DPRINTK (PHASE_RESELECT, "scsi%d : seagate_reconnect_intr() called\n", hostno);
-
-	if (!should_reconnect)
-		printk(KERN_WARNING "scsi%d: unexpected interrupt.\n", hostno);
-	else {
-		should_reconnect = 0;
-
-		DPRINTK (PHASE_RESELECT, "scsi%d : internal_command(%d, %08x, %08x, RECONNECT_NOW\n", 
-			hostno, current_target, current_data, current_bufflen);
-
-		temp = internal_command (current_target, current_lun, current_cmnd, current_data, current_bufflen, RECONNECT_NOW);
-
-		if (msg_byte(temp) != DISCONNECT) {
-			if (done_fn) {
-				DPRINTK(PHASE_RESELECT, "scsi%d : done_fn(%d,%08x)", hostno, hostno, temp);
-				if (!SCint)
-					panic ("SCint == NULL in seagate");
-				SCtmp = SCint;
-				SCint = NULL;
-				SCtmp->result = temp;
-				done_fn(SCtmp);
-			} else
-				printk(KERN_ERR "done_fn() not defined.\n");
-		}
-	}
-}
-
-/*
- * The seagate_st0x_queue_command() function provides a queued interface
- * to the seagate SCSI driver.  Basically, it just passes control onto the
- * seagate_command() function, after fixing it so that the done_fn()
- * is set to the one passed to the function.  We have to be very careful,
- * because there are some commands on some devices that do not disconnect,
- * and if we simply call the done_fn when the command is done then another
- * command is started and queue_command is called again...  We end up
- * overflowing the kernel stack, and this tends not to be such a good idea.
- */
-
-static int recursion_depth = 0;
-
-static int seagate_st0x_queue_command(struct scsi_cmnd * SCpnt,
-				      void (*done) (struct scsi_cmnd *))
-{
-	int result, reconnect;
-	struct scsi_cmnd *SCtmp;
-
-	DANY ("seagate: que_command");
-	done_fn = done;
-	current_target = SCpnt->device->id;
-	current_lun = SCpnt->device->lun;
-	current_cmnd = SCpnt->cmnd;
-	current_data = (unsigned char *) SCpnt->request_buffer;
-	current_bufflen = SCpnt->request_bufflen;
-	SCint = SCpnt;
-	if (recursion_depth)
-		return 1;
-	recursion_depth++;
-	do {
-#ifdef LINKED
-		/*
-		 * Set linked command bit in control field of SCSI command.
-		 */
-
-		current_cmnd[SCpnt->cmd_len] |= 0x01;
-		if (linked_connected) {
-			DPRINTK (DEBUG_LINKED, "scsi%d : using linked commands, current I_T_L nexus is ", hostno);
-			if (linked_target == current_target && linked_lun == current_lun) 
-			{
-				DPRINTK(DEBUG_LINKED, "correct\n");
-				reconnect = LINKED_RIGHT;
-			} else {
-				DPRINTK(DEBUG_LINKED, "incorrect\n");
-				reconnect = LINKED_WRONG;
-			}
-		} else
-#endif				/* LINKED */
-			reconnect = CAN_RECONNECT;
-
-		result = internal_command(SCint->device->id, SCint->device->lun, SCint->cmnd,
-				      SCint->request_buffer, SCint->request_bufflen, reconnect);
-		if (msg_byte(result) == DISCONNECT)
-			break;
-		SCtmp = SCint;
-		SCint = NULL;
-		SCtmp->result = result;
-		done_fn(SCtmp);
-	}
-	while (SCint);
-	recursion_depth--;
-	return 0;
-}
-
-static int internal_command (unsigned char target, unsigned char lun,
-		  const void *cmnd, void *buff, int bufflen, int reselect)
-{
-	unsigned char *data = NULL;
-	struct scatterlist *buffer = NULL;
-	int clock, temp, nobuffs = 0, done = 0, len = 0;
-#if DEBUG
-	int transfered = 0, phase = 0, newphase;
-#endif
-	register unsigned char status_read;
-	unsigned char tmp_data, tmp_control, status = 0, message = 0;
-	unsigned transfersize = 0, underflow = 0;
-#ifdef SLOW_RATE
-	int borken = (int) SCint->device->borken;	/* Does the current target require
-							   Very Slow I/O ?  */
-#endif
-
-	incommand = 0;
-	st0x_aborted = 0;
-
-#if (DEBUG & PRINT_COMMAND)
-	printk("scsi%d : target = %d, command = ", hostno, target);
-	__scsi_print_command((unsigned char *) cmnd);
-#endif
-
-#if (DEBUG & PHASE_RESELECT)
-	switch (reselect) {
-	case RECONNECT_NOW:
-		printk("scsi%d : reconnecting\n", hostno);
-		break;
-#ifdef LINKED
-	case LINKED_RIGHT:
-		printk("scsi%d : connected, can reconnect\n", hostno);
-		break;
-	case LINKED_WRONG:
-		printk("scsi%d : connected to wrong target, can reconnect\n",
-			hostno);
-		break;
-#endif
-	case CAN_RECONNECT:
-		printk("scsi%d : allowed to reconnect\n", hostno);
-		break;
-	default:
-		printk("scsi%d : not allowed to reconnect\n", hostno);
-	}
-#endif
-
-	if (target == (controller_type == SEAGATE ? 7 : 6))
-		return DID_BAD_TARGET;
-
-	/*
-	 *	We work it differently depending on if this is is "the first time,"
-	 *      or a reconnect.  If this is a reselect phase, then SEL will
-	 *      be asserted, and we must skip selection / arbitration phases.
-	 */
-
-	switch (reselect) {
-	case RECONNECT_NOW:
-		DPRINTK (PHASE_RESELECT, "scsi%d : phase RESELECT \n", hostno);
-		/*
-		 *	At this point, we should find the logical or of our ID
-		 *	and the original target's ID on the BUS, with BSY, SEL,
-		 *	and I/O signals asserted.
-		 *
-		 *      After ARBITRATION phase is completed, only SEL, BSY,
-		 *	and the target ID are asserted.  A valid initiator ID
-		 *	is not on the bus until IO is asserted, so we must wait
-		 *	for that.
-		 */
-		ULOOP (100 * 1000) {
-			temp = STATUS;
-			if ((temp & STAT_IO) && !(temp & STAT_BSY))
-				break;
-			if (TIMEOUT) {
-				DPRINTK (PHASE_RESELECT, "scsi%d : RESELECT timed out while waiting for IO .\n", hostno);
-				return (DID_BAD_INTR << 16);
-			}
-		}
-
-		/*
-		 *	After I/O is asserted by the target, we can read our ID
-		 *	and its ID off of the BUS.
-		 */
-
-		if (!((temp = DATA) & (controller_type == SEAGATE ? 0x80 : 0x40))) {
-			DPRINTK (PHASE_RESELECT, "scsi%d : detected reconnect request to different target.\n\tData bus = %d\n", hostno, temp);
-			return (DID_BAD_INTR << 16);
-		}
-
-		if (!(temp & (1 << current_target))) {
-			printk(KERN_WARNING "scsi%d : Unexpected reselect interrupt.  Data bus = %d\n", hostno, temp);
-			return (DID_BAD_INTR << 16);
-		}
-
-		buffer = current_buffer;
-		cmnd = current_cmnd;	/* WDE add */
-		data = current_data;	/* WDE add */
-		len = current_bufflen;	/* WDE add */
-		nobuffs = current_nobuffs;
-
-		/*
-		 *	We have determined that we have been selected.  At this
-		 *	point, we must respond to the reselection by asserting
-		 *	BSY ourselves
-		 */
-
-#if 1
-		WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | CMD_BSY);
-#else
-		WRITE_CONTROL (BASE_CMD | CMD_BSY);
-#endif
-
-		/*
-		 *	The target will drop SEL, and raise BSY, at which time
-		 *	we must drop BSY.
-		 */
-
-		ULOOP (100 * 1000) {
-			if (!(STATUS & STAT_SEL))
-				break;
-			if (TIMEOUT) {
-				WRITE_CONTROL (BASE_CMD | CMD_INTR);
-				DPRINTK (PHASE_RESELECT, "scsi%d : RESELECT timed out while waiting for SEL.\n", hostno);
-				return (DID_BAD_INTR << 16);
-			}
-		}
-		WRITE_CONTROL (BASE_CMD);
-		/*
-		 *	At this point, we have connected with the target
-		 *	and can get on with our lives.
-		 */
-		break;
-	case CAN_RECONNECT:
-#ifdef LINKED
-		/*
-		 * This is a bletcherous hack, just as bad as the Unix #!
-		 * interpreter stuff. If it turns out we are using the wrong
-		 * I_T_L nexus, the easiest way to deal with it is to go into
-		 *  our INFORMATION TRANSFER PHASE code, send a ABORT
-		 * message on MESSAGE OUT phase, and then loop back to here.
-		 */
-connect_loop:
-#endif
-		DPRINTK (PHASE_BUS_FREE, "scsi%d : phase = BUS FREE \n", hostno);
-
-		/*
-		 *    BUS FREE PHASE
-		 *
-		 *      On entry, we make sure that the BUS is in a BUS FREE
-		 *      phase, by insuring that both BSY and SEL are low for
-		 *      at least one bus settle delay.  Several reads help
-		 *      eliminate wire glitch.
-		 */
-
-#ifndef ARBITRATE
-#error FIXME: this is broken: we may not use jiffies here - we are under cli(). It will hardlock.
-		clock = jiffies + ST0X_BUS_FREE_DELAY;
-
-		while (((STATUS | STATUS | STATUS) & (STAT_BSY | STAT_SEL)) && (!st0x_aborted) && time_before (jiffies, clock))
-			cpu_relax();
-
-		if (time_after (jiffies, clock))
-			return retcode (DID_BUS_BUSY);
-		else if (st0x_aborted)
-			return retcode (st0x_aborted);
-#endif
-		DPRINTK (PHASE_SELECTION, "scsi%d : phase = SELECTION\n", hostno);
-
-		clock = jiffies + ST0X_SELECTION_DELAY;
-
-		/*
-		 * Arbitration/selection procedure :
-		 * 1.  Disable drivers
-		 * 2.  Write HOST adapter address bit
-		 * 3.  Set start arbitration.
-		 * 4.  We get either ARBITRATION COMPLETE or SELECT at this
-		 *     point.
-		 * 5.  OR our ID and targets on bus.
-		 * 6.  Enable SCSI drivers and asserted SEL and ATTN
-		 */
-
-#ifdef ARBITRATE
-		/* FIXME: verify host lock is always held here */
-		WRITE_CONTROL(0);
-		WRITE_DATA((controller_type == SEAGATE) ? 0x80 : 0x40);
-		WRITE_CONTROL(CMD_START_ARB);
-
-		ULOOP (ST0X_SELECTION_DELAY * 10000) {
-			status_read = STATUS;
-			if (status_read & STAT_ARB_CMPL)
-				break;
-			if (st0x_aborted)	/* FIXME: What? We are going to do something even after abort? */
-				break;
-			if (TIMEOUT || (status_read & STAT_SEL)) {
-				printk(KERN_WARNING "scsi%d : arbitration lost or timeout.\n", hostno);
-				WRITE_CONTROL (BASE_CMD);
-				return retcode (DID_NO_CONNECT);
-			}
-		}
-		DPRINTK (PHASE_SELECTION, "scsi%d : arbitration complete\n", hostno);
-#endif
-
-		/*
-		 *    When the SCSI device decides that we're gawking at it, 
-		 *    it will respond by asserting BUSY on the bus.
-		 *
-		 *    Note : the Seagate ST-01/02 product manual says that we
-		 *    should twiddle the DATA register before the control
-		 *    register. However, this does not work reliably so we do
-		 *    it the other way around.
-		 *
-		 *    Probably could be a problem with arbitration too, we
-		 *    really should try this with a SCSI protocol or logic 
-		 *    analyzer to see what is going on.
-		 */
-		tmp_data = (unsigned char) ((1 << target) | (controller_type == SEAGATE ? 0x80 : 0x40));
-		tmp_control = BASE_CMD | CMD_DRVR_ENABLE | CMD_SEL | (reselect ? CMD_ATTN : 0);
-
-		/* FIXME: verify host lock is always held here */
-#ifdef OLDCNTDATASCEME
-#ifdef SWAPCNTDATA
-		WRITE_CONTROL (tmp_control);
-		WRITE_DATA (tmp_data);
-#else
-		WRITE_DATA (tmp_data);
-		WRITE_CONTROL (tmp_control);
-#endif
-#else
-		tmp_control ^= CMD_BSY;	/* This is guesswork. What used to be in driver    */
-		WRITE_CONTROL (tmp_control);	/* could never work: it sent data into control     */
-		WRITE_DATA (tmp_data);	/* register and control info into data. Hopefully  */
-		tmp_control ^= CMD_BSY;	/* fixed, but order of first two may be wrong.     */
-		WRITE_CONTROL (tmp_control);	/* -- pavel@ucw.cz   */
-#endif
-
-		ULOOP (250 * 1000) {
-			if (st0x_aborted) {
-				/*
-				 *	If we have been aborted, and we have a
-				 *	command in progress, IE the target 
-				 *	still has BSY asserted, then we will
-				 *	reset the bus, and notify the midlevel
-				 *	driver to expect sense.
-				 */
-
-				WRITE_CONTROL (BASE_CMD);
-				if (STATUS & STAT_BSY) {
-					printk(KERN_WARNING "scsi%d : BST asserted after we've been aborted.\n", hostno);
-					seagate_st0x_bus_reset(NULL);
-					return retcode (DID_RESET);
-				}
-				return retcode (st0x_aborted);
-			}
-			if (STATUS & STAT_BSY)
-				break;
-			if (TIMEOUT) {
-				DPRINTK (PHASE_SELECTION, "scsi%d : NO CONNECT with target %d, stat = %x \n", hostno, target, STATUS);
-				return retcode (DID_NO_CONNECT);
-			}
-		}
-
-		/* Establish current pointers.  Take into account scatter / gather */
-
-		if ((nobuffs = SCint->use_sg)) {
-#if (DEBUG & DEBUG_SG)
-			{
-				int i;
-				printk("scsi%d : scatter gather requested, using %d buffers.\n", hostno, nobuffs);
-				for (i = 0; i < nobuffs; ++i)
-					printk("scsi%d : buffer %d address = %p length = %d\n",
-					     hostno, i,
-					     sg_virt(&buffer[i]),
-					     buffer[i].length);
-			}
-#endif
-
-			buffer = (struct scatterlist *) SCint->request_buffer;
-			len = buffer->length;
-			data = sg_virt(buffer);
-		} else {
-			DPRINTK (DEBUG_SG, "scsi%d : scatter gather not requested.\n", hostno);
-			buffer = NULL;
-			len = SCint->request_bufflen;
-			data = (unsigned char *) SCint->request_buffer;
-		}
-
-		DPRINTK (PHASE_DATAIN | PHASE_DATAOUT, "scsi%d : len = %d\n",
-			 hostno, len);
-
-		break;
-#ifdef LINKED
-	case LINKED_RIGHT:
-		break;
-	case LINKED_WRONG:
-		break;
-#endif
-	}			/* end of switch(reselect) */
-
-	/*
-	 *    There are several conditions under which we wish to send a message :
-	 *      1.  When we are allowing disconnect / reconnect, and need to
-	 *	establish the I_T_L nexus via an IDENTIFY with the DiscPriv bit
-	 *	set.
-	 *
-	 *      2.  When we are doing linked commands, are have the wrong I_T_L
-	 *	nexus established and want to send an ABORT message.
-	 */
-
-	/* GCC does not like an ifdef inside a macro, so do it the hard way. */
-#ifdef LINKED
-	WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | (((reselect == CAN_RECONNECT)|| (reselect == LINKED_WRONG))? CMD_ATTN : 0));
-#else
-	WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | (((reselect == CAN_RECONNECT))? CMD_ATTN : 0));
-#endif
-
-	/*
-	 *    INFORMATION TRANSFER PHASE
-	 *
-	 *      The nasty looking read / write inline assembler loops we use for
-	 *      DATAIN and DATAOUT phases are approximately 4-5 times as fast as
-	 *      the 'C' versions - since we're moving 1024 bytes of data, this
-	 *      really adds up.
-	 *
-	 *      SJT: The nasty-looking assembler is gone, so it's slower.
-	 *
-	 */
-
-	DPRINTK (PHASE_ETC, "scsi%d : phase = INFORMATION TRANSFER\n", hostno);
-
-	incommand = 1;
-	transfersize = SCint->transfersize;
-	underflow = SCint->underflow;
-
-	/*
-	 *	Now, we poll the device for status information,
-	 *      and handle any requests it makes.  Note that since we are unsure
-	 *	of how much data will be flowing across the system, etc and
-	 *	cannot make reasonable timeouts, that we will instead have the
-	 *	midlevel driver handle any timeouts that occur in this phase.
-	 */
-
-	while (((status_read = STATUS) & STAT_BSY) && !st0x_aborted && !done) {
-#ifdef PARITY
-		if (status_read & STAT_PARITY) {
-			printk(KERN_ERR "scsi%d : got parity error\n", hostno);
-			st0x_aborted = DID_PARITY;
-		}
-#endif
-		if (status_read & STAT_REQ) {
-#if ((DEBUG & PHASE_ETC) == PHASE_ETC)
-			if ((newphase = (status_read & REQ_MASK)) != phase) {
-				phase = newphase;
-				switch (phase) {
-				case REQ_DATAOUT:
-					printk ("scsi%d : phase = DATA OUT\n", hostno);
-					break;
-				case REQ_DATAIN:
-					printk ("scsi%d : phase = DATA IN\n", hostno);
-					break;
-				case REQ_CMDOUT:
-					printk
-					    ("scsi%d : phase = COMMAND OUT\n", hostno);
-					break;
-				case REQ_STATIN:
-					printk ("scsi%d : phase = STATUS IN\n",	hostno);
-					break;
-				case REQ_MSGOUT:
-					printk
-					    ("scsi%d : phase = MESSAGE OUT\n", hostno);
-					break;
-				case REQ_MSGIN:
-					printk ("scsi%d : phase = MESSAGE IN\n", hostno);
-					break;
-				default:
-					printk ("scsi%d : phase = UNKNOWN\n", hostno);
-					st0x_aborted = DID_ERROR;
-				}
-			}
-#endif
-			switch (status_read & REQ_MASK) {
-			case REQ_DATAOUT:
-				/*
-				 * If we are in fast mode, then we simply splat
-				 * the data out in word-sized chunks as fast as
-				 * we can.
-				 */
-
-				if (!len) {
-#if 0
-					printk("scsi%d: underflow to target %d lun %d \n", hostno, target, lun);
-					st0x_aborted = DID_ERROR;
-					fast = 0;
-#endif
-					break;
-				}
-
-				if (fast && transfersize
-				    && !(len % transfersize)
-				    && (len >= transfersize)
-#ifdef FAST32
-				    && !(transfersize % 4)
-#endif
-				    ) {
-					DPRINTK (DEBUG_FAST,
-						 "scsi%d : FAST transfer, underflow = %d, transfersize = %d\n"
-						 "         len = %d, data = %08x\n",
-						 hostno, SCint->underflow,
-						 SCint->transfersize, len,
-						 data);
-
-			/* SJT: Start. Fast Write */
-#ifdef SEAGATE_USE_ASM
-					__asm__ ("cld\n\t"
-#ifdef FAST32
-						 "shr $2, %%ecx\n\t"
-						 "1:\t"
-						 "lodsl\n\t"
-						 "movl %%eax, (%%edi)\n\t"
-#else
-						 "1:\t"
-						 "lodsb\n\t"
-						 "movb %%al, (%%edi)\n\t"
-#endif
-						 "loop 1b;"
-				      /* output */ :
-				      /* input */ :"D" (st0x_dr),
-						 "S"
-						 (data),
-						 "c" (SCint->transfersize)
-/* clobbered */
-				      :	 "eax", "ecx",
-						 "esi");
-#else				/* SEAGATE_USE_ASM */
-					memcpy_toio(st0x_dr, data, transfersize);
-#endif				/* SEAGATE_USE_ASM */
-/* SJT: End */
-					len -= transfersize;
-					data += transfersize;
-					DPRINTK (DEBUG_FAST, "scsi%d : FAST transfer complete len = %d data = %08x\n", hostno, len, data);
-				} else {
-					/*
-					 *    We loop as long as we are in a 
-					 *    data out phase, there is data to
-					 *    send, and BSY is still active.
-					 */
-
-/* SJT: Start. Slow Write. */
-#ifdef SEAGATE_USE_ASM
-
-					int __dummy_1, __dummy_2;
-
-/*
- *      We loop as long as we are in a data out phase, there is data to send, 
- *      and BSY is still active.
- */
-/* Local variables : len = ecx , data = esi, 
-                     st0x_cr_sr = ebx, st0x_dr =  edi
-*/
-					__asm__ (
-							/* Test for any data here at all. */
-							"orl %%ecx, %%ecx\n\t"
-							"jz 2f\n\t" "cld\n\t"
-/*                    "movl st0x_cr_sr, %%ebx\n\t"  */
-/*                    "movl st0x_dr, %%edi\n\t"  */
-							"1:\t"
-							"movb (%%ebx), %%al\n\t"
-							/* Test for BSY */
-							"test $1, %%al\n\t"
-							"jz 2f\n\t"
-							/* Test for data out phase - STATUS & REQ_MASK should be 
-							   REQ_DATAOUT, which is 0. */
-							"test $0xe, %%al\n\t"
-							"jnz 2f\n\t"
-							/* Test for REQ */
-							"test $0x10, %%al\n\t"
-							"jz 1b\n\t"
-							"lodsb\n\t"
-							"movb %%al, (%%edi)\n\t"
-							"loop 1b\n\t" "2:\n"
-				      /* output */ :"=S" (data), "=c" (len),
-							"=b"
-							(__dummy_1),
-							"=D" (__dummy_2)
-/* input */
-				      :		"0" (data), "1" (len),
-							"2" (st0x_cr_sr),
-							"3" (st0x_dr)
-/* clobbered */
-				      :		"eax");
-#else				/* SEAGATE_USE_ASM */
-					while (len) {
-						unsigned char stat;
-
-						stat = STATUS;
-						if (!(stat & STAT_BSY)
-						    || ((stat & REQ_MASK) !=
-							REQ_DATAOUT))
-							break;
-						if (stat & STAT_REQ) {
-							WRITE_DATA (*data++);
-							--len;
-						}
-					}
-#endif				/* SEAGATE_USE_ASM */
-/* SJT: End. */
-				}
-
-				if (!len && nobuffs) {
-					--nobuffs;
-					++buffer;
-					len = buffer->length;
-					data = sg_virt(buffer);
-					DPRINTK (DEBUG_SG,
-						 "scsi%d : next scatter-gather buffer len = %d address = %08x\n",
-						 hostno, len, data);
-				}
-				break;
-
-			case REQ_DATAIN:
-#ifdef SLOW_RATE
-				if (borken) {
-#if (DEBUG & (PHASE_DATAIN))
-					transfered += len;
-#endif
-					for (; len && (STATUS & (REQ_MASK | STAT_REQ)) == (REQ_DATAIN | STAT_REQ); --len) {
-						*data++ = DATA;
-						borken_wait();
-					}
-#if (DEBUG & (PHASE_DATAIN))
-					transfered -= len;
-#endif
-				} else
-#endif
-
-					if (fast && transfersize
-					    && !(len % transfersize)
-					    && (len >= transfersize)
-#ifdef FAST32
-					    && !(transfersize % 4)
-#endif
-				    ) {
-					DPRINTK (DEBUG_FAST,
-						 "scsi%d : FAST transfer, underflow = %d, transfersize = %d\n"
-						 "         len = %d, data = %08x\n",
-						 hostno, SCint->underflow,
-						 SCint->transfersize, len,
-						 data);
-
-/* SJT: Start. Fast Read */
-#ifdef SEAGATE_USE_ASM
-					__asm__ ("cld\n\t"
-#ifdef FAST32
-						 "shr $2, %%ecx\n\t"
-						 "1:\t"
-						 "movl (%%esi), %%eax\n\t"
-						 "stosl\n\t"
-#else
-						 "1:\t"
-						 "movb (%%esi), %%al\n\t"
-						 "stosb\n\t"
-#endif
-						 "loop 1b\n\t"
-				      /* output */ :
-				      /* input */ :"S" (st0x_dr),
-						 "D"
-						 (data),
-						 "c" (SCint->transfersize)
-/* clobbered */
-				      :	 "eax", "ecx",
-						 "edi");
-#else				/* SEAGATE_USE_ASM */
-					memcpy_fromio(data, st0x_dr, len);
-#endif				/* SEAGATE_USE_ASM */
-/* SJT: End */
-					len -= transfersize;
-					data += transfersize;
-#if (DEBUG & PHASE_DATAIN)
-					printk ("scsi%d: transfered += %d\n", hostno, transfersize);
-					transfered += transfersize;
-#endif
-
-					DPRINTK (DEBUG_FAST, "scsi%d : FAST transfer complete len = %d data = %08x\n", hostno, len, data);
-				} else {
-
-#if (DEBUG & PHASE_DATAIN)
-					printk ("scsi%d: transfered += %d\n", hostno, len);
-					transfered += len;	/* Assume we'll transfer it all, then
-								   subtract what we *didn't* transfer */
-#endif
-
-/*
- *	We loop as long as we are in a data in phase, there is room to read,
- *      and BSY is still active
- */
-
-/* SJT: Start. */
-#ifdef SEAGATE_USE_ASM
-
-					int __dummy_3, __dummy_4;
-
-/* Dummy clobbering variables for the new gcc-2.95 */
-
-/*
- *      We loop as long as we are in a data in phase, there is room to read, 
- *      and BSY is still active
- */
-					/* Local variables : ecx = len, edi = data
-					   esi = st0x_cr_sr, ebx = st0x_dr */
-					__asm__ (
-							/* Test for room to read */
-							"orl %%ecx, %%ecx\n\t"
-							"jz 2f\n\t" "cld\n\t"
-/*                "movl st0x_cr_sr, %%esi\n\t"  */
-/*                "movl st0x_dr, %%ebx\n\t"  */
-							"1:\t"
-							"movb (%%esi), %%al\n\t"
-							/* Test for BSY */
-							"test $1, %%al\n\t"
-							"jz 2f\n\t"
-							/* Test for data in phase - STATUS & REQ_MASK should be REQ_DATAIN, 
-							   = STAT_IO, which is 4. */
-							"movb $0xe, %%ah\n\t"
-							"andb %%al, %%ah\n\t"
-							"cmpb $0x04, %%ah\n\t"
-							"jne 2f\n\t"
-							/* Test for REQ */
-							"test $0x10, %%al\n\t"
-							"jz 1b\n\t"
-							"movb (%%ebx), %%al\n\t"
-							"stosb\n\t"
-							"loop 1b\n\t" "2:\n"
-				      /* output */ :"=D" (data), "=c" (len),
-							"=S"
-							(__dummy_3),
-							"=b" (__dummy_4)
-/* input */
-				      :		"0" (data), "1" (len),
-							"2" (st0x_cr_sr),
-							"3" (st0x_dr)
-/* clobbered */
-				      :		"eax");
-#else				/* SEAGATE_USE_ASM */
-					while (len) {
-						unsigned char stat;
-
-						stat = STATUS;
-						if (!(stat & STAT_BSY)
-						    || ((stat & REQ_MASK) !=
-							REQ_DATAIN))
-							break;
-						if (stat & STAT_REQ) {
-							*data++ = DATA;
-							--len;
-						}
-					}
-#endif				/* SEAGATE_USE_ASM */
-/* SJT: End. */
-#if (DEBUG & PHASE_DATAIN)
-					printk ("scsi%d: transfered -= %d\n", hostno, len);
-					transfered -= len;	/* Since we assumed all of Len got  *
-								   transfered, correct our mistake */
-#endif
-				}
-
-				if (!len && nobuffs) {
-					--nobuffs;
-					++buffer;
-					len = buffer->length;
-					data = sg_virt(buffer);
-					DPRINTK (DEBUG_SG, "scsi%d : next scatter-gather buffer len = %d address = %08x\n", hostno, len, data);
-				}
-				break;
-
-			case REQ_CMDOUT:
-				while (((status_read = STATUS) & STAT_BSY) &&
-				       ((status_read & REQ_MASK) == REQ_CMDOUT))
-					if (status_read & STAT_REQ) {
-						WRITE_DATA (*(const unsigned char *) cmnd);
-						cmnd = 1 + (const unsigned char *)cmnd;
-#ifdef SLOW_RATE
-						if (borken)
-							borken_wait ();
-#endif
-					}
-				break;
-
-			case REQ_STATIN:
-				status = DATA;
-				break;
-
-			case REQ_MSGOUT:
-				/*
-				 *	We can only have sent a MSG OUT if we
-				 *	requested to do this by raising ATTN.
-				 *	So, we must drop ATTN.
-				 */
-				WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE);
-				/*
-				 *	If we are reconnecting, then we must 
-				 *	send an IDENTIFY message in response
-				 *	to MSGOUT.
-				 */
-				switch (reselect) {
-				case CAN_RECONNECT:
-					WRITE_DATA (IDENTIFY (1, lun));
-					DPRINTK (PHASE_RESELECT | PHASE_MSGOUT, "scsi%d : sent IDENTIFY message.\n", hostno);
-					break;
-#ifdef LINKED
-				case LINKED_WRONG:
-					WRITE_DATA (ABORT);
-					linked_connected = 0;
-					reselect = CAN_RECONNECT;
-					goto connect_loop;
-					DPRINTK (PHASE_MSGOUT | DEBUG_LINKED, "scsi%d : sent ABORT message to cancel incorrect I_T_L nexus.\n", hostno);
-#endif					/* LINKED */
-					DPRINTK (DEBUG_LINKED, "correct\n");
-				default:
-					WRITE_DATA (NOP);
-					printk("scsi%d : target %d requested MSGOUT, sent NOP message.\n", hostno, target);
-				}
-				break;
-
-			case REQ_MSGIN:
-				switch (message = DATA) {
-				case DISCONNECT:
-					DANY("seagate: deciding to disconnect\n");
-					should_reconnect = 1;
-					current_data = data;	/* WDE add */
-					current_buffer = buffer;
-					current_bufflen = len;	/* WDE add */
-					current_nobuffs = nobuffs;
-#ifdef LINKED
-					linked_connected = 0;
-#endif
-					done = 1;
-					DPRINTK ((PHASE_RESELECT | PHASE_MSGIN), "scsi%d : disconnected.\n", hostno);
-					break;
-
-#ifdef LINKED
-				case LINKED_CMD_COMPLETE:
-				case LINKED_FLG_CMD_COMPLETE:
-#endif
-				case COMMAND_COMPLETE:
-					/*
-					 * Note : we should check for underflow here.
-					 */
-					DPRINTK(PHASE_MSGIN, "scsi%d : command complete.\n", hostno);
-					done = 1;
-					break;
-				case ABORT:
-					DPRINTK(PHASE_MSGIN, "scsi%d : abort message.\n", hostno);
-					done = 1;
-					break;
-				case SAVE_POINTERS:
-					current_buffer = buffer;
-					current_bufflen = len;	/* WDE add */
-					current_data = data;	/* WDE mod */
-					current_nobuffs = nobuffs;
-					DPRINTK (PHASE_MSGIN, "scsi%d : pointers saved.\n", hostno);
-					break;
-				case RESTORE_POINTERS:
-					buffer = current_buffer;
-					cmnd = current_cmnd;
-					data = current_data;	/* WDE mod */
-					len = current_bufflen;
-					nobuffs = current_nobuffs;
-					DPRINTK(PHASE_MSGIN, "scsi%d : pointers restored.\n", hostno);
-					break;
-				default:
-
-					/*
-					 *	IDENTIFY distinguishes itself
-					 *	from the other messages by 
-					 *	setting the high bit.
-					 *
-					 *      Note : we need to handle at 
-					 *	least one outstanding command
-					 *	per LUN, and need to hash the 
-					 *	SCSI command for that I_T_L
-					 *	nexus based on the known ID 
-					 *	(at this point) and LUN.
-					 */
-
-					if (message & 0x80) {
-						DPRINTK (PHASE_MSGIN, "scsi%d : IDENTIFY message received from id %d, lun %d.\n", hostno, target, message & 7);
-					} else {
-						/*
-						 *      We should go into a
-						 *	MESSAGE OUT phase, and
-						 *	send  a MESSAGE_REJECT
-						 *      if we run into a message 
-						 *	that we don't like.  The
-						 *	seagate driver needs 
-						 *	some serious 
-						 *	restructuring first
-						 *	though.
-						 */
-						DPRINTK (PHASE_MSGIN, "scsi%d : unknown message %d from target %d.\n", hostno, message, target);
-					}
-				}
-				break;
-			default:
-				printk(KERN_ERR "scsi%d : unknown phase.\n", hostno);
-				st0x_aborted = DID_ERROR;
-			}	/* end of switch (status_read &  REQ_MASK) */
-#ifdef SLOW_RATE
-			/*
-			 * I really don't care to deal with borken devices in
-			 * each single byte transfer case (ie, message in,
-			 * message out, status), so I'll do the wait here if 
-			 * necessary.
-			 */
-			if(borken)
-				borken_wait();
-#endif
-
-		}		/* if(status_read & STAT_REQ) ends */
-	}			/* while(((status_read = STATUS)...) ends */
-
-	DPRINTK(PHASE_DATAIN | PHASE_DATAOUT | PHASE_EXIT, "scsi%d : Transfered %d bytes\n", hostno, transfered);
-
-#if (DEBUG & PHASE_EXIT)
-#if 0				/* Doesn't work for scatter/gather */
-	printk("Buffer : \n");
-	for(i = 0; i < 20; ++i)
-		printk("%02x  ", ((unsigned char *) data)[i]);	/* WDE mod */
-	printk("\n");
-#endif
-	printk("scsi%d : status = ", hostno);
-	scsi_print_status(status);
-	printk(" message = %02x\n", message);
-#endif
-
-	/* We shouldn't reach this until *after* BSY has been deasserted */
-
-#ifdef LINKED
-	else
-	{
-		/*
-		 * Fix the message byte so that unsuspecting high level drivers
-		 * don't puke when they see a LINKED COMMAND message in place of
-		 * the COMMAND COMPLETE they may be expecting.  Shouldn't be
-		 * necessary, but it's better to be on the safe side.
-		 *
-		 * A non LINKED* message byte will indicate that the command
-		 * completed, and we are now disconnected.
-		 */
-
-		switch (message) {
-		case LINKED_CMD_COMPLETE:
-		case LINKED_FLG_CMD_COMPLETE:
-			message = COMMAND_COMPLETE;
-			linked_target = current_target;
-			linked_lun = current_lun;
-			linked_connected = 1;
-			DPRINTK (DEBUG_LINKED, "scsi%d : keeping I_T_L nexus established for linked command.\n", hostno);
-			/* We also will need to adjust status to accommodate intermediate
-			   conditions. */
-			if ((status == INTERMEDIATE_GOOD) || (status == INTERMEDIATE_C_GOOD))
-				status = GOOD;
-			break;
-			/*
-			 * We should also handle what are "normal" termination
-			 * messages here (ABORT, BUS_DEVICE_RESET?, and
-			 * COMMAND_COMPLETE individually, and flake if things
-			 * aren't right.
-			 */
-		default:
-			DPRINTK (DEBUG_LINKED, "scsi%d : closing I_T_L nexus.\n", hostno);
-			linked_connected = 0;
-		}
-	}
-#endif	/* LINKED */
-
-	if (should_reconnect) {
-		DPRINTK (PHASE_RESELECT, "scsi%d : exiting seagate_st0x_queue_command() with reconnect enabled.\n", hostno);
-		WRITE_CONTROL (BASE_CMD | CMD_INTR);
-	} else
-		WRITE_CONTROL (BASE_CMD);
-
-	return retcode (st0x_aborted);
-}				/* end of internal_command */
-
-static int seagate_st0x_abort(struct scsi_cmnd * SCpnt)
-{
-	st0x_aborted = DID_ABORT;
-	return SUCCESS;
-}
-
-#undef ULOOP
-#undef TIMEOUT
-
-/*
- * the seagate_st0x_reset function resets the SCSI bus 
- *
- * May be called with SCpnt = NULL
- */
-
-static int seagate_st0x_bus_reset(struct scsi_cmnd * SCpnt)
-{
-	/* No timeouts - this command is going to fail because it was reset. */
-	DANY ("scsi%d: Reseting bus... ", hostno);
-
-	/* assert  RESET signal on SCSI bus.  */
-	WRITE_CONTROL (BASE_CMD | CMD_RST);
-
-	mdelay (20);
-
-	WRITE_CONTROL (BASE_CMD);
-	st0x_aborted = DID_RESET;
-
-	DANY ("done.\n");
-	return SUCCESS;
-}
-
-static int seagate_st0x_release(struct Scsi_Host *shost)
-{
-	if (shost->irq)
-		free_irq(shost->irq, shost);
-	release_region(shost->io_port, shost->n_io_port);
-	return 0;
-}
-
-static struct scsi_host_template driver_template = {
-	.detect         	= seagate_st0x_detect,
-	.release        	= seagate_st0x_release,
-	.info           	= seagate_st0x_info,
-	.queuecommand   	= seagate_st0x_queue_command,
-	.eh_abort_handler	= seagate_st0x_abort,
-	.eh_bus_reset_handler	= seagate_st0x_bus_reset,
-	.can_queue      	= 1,
-	.this_id        	= 7,
-	.sg_tablesize   	= SG_ALL,
-	.cmd_per_lun    	= 1,
-	.use_clustering		= DISABLE_CLUSTERING,
-};
-#include "scsi_module.c"