tty: move drivers/serial/ to drivers/tty/serial/

The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.

This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 0 insertions, 709 deletions

diff --git a/drivers/serial/apbuart.c b/drivers/serial/apbuart.c
deleted file mode 100644
index 095a5d56261..00000000000
--- a/drivers/serial/apbuart.c
+++ /dev/null
@@ -1,709 +0,0 @@
-/*
- *  Driver for GRLIB serial ports (APBUART)
- *
- *  Based on linux/drivers/serial/amba.c
- *
- *  Copyright (C) 2000 Deep Blue Solutions Ltd.
- *  Copyright (C) 2003 Konrad Eisele <eiselekd@web.de>
- *  Copyright (C) 2006 Daniel Hellstrom <daniel@gaisler.com>, Aeroflex Gaisler AB
- *  Copyright (C) 2008 Gilead Kutnick <kutnickg@zin-tech.com>
- *  Copyright (C) 2009 Kristoffer Glembo <kristoffer@gaisler.com>, Aeroflex Gaisler AB
- */
-
-#if defined(CONFIG_SERIAL_GRLIB_GAISLER_APBUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/module.h>
-#include <linux/tty.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/serial.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/kthread.h>
-#include <linux/device.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/of_platform.h>
-#include <linux/of_irq.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/serial_core.h>
-#include <asm/irq.h>
-
-#include "apbuart.h"
-
-#define SERIAL_APBUART_MAJOR	TTY_MAJOR
-#define SERIAL_APBUART_MINOR	64
-#define UART_DUMMY_RSR_RX	0x8000	/* for ignore all read */
-
-static void apbuart_tx_chars(struct uart_port *port);
-
-static void apbuart_stop_tx(struct uart_port *port)
-{
-	unsigned int cr;
-
-	cr = UART_GET_CTRL(port);
-	cr &= ~UART_CTRL_TI;
-	UART_PUT_CTRL(port, cr);
-}
-
-static void apbuart_start_tx(struct uart_port *port)
-{
-	unsigned int cr;
-
-	cr = UART_GET_CTRL(port);
-	cr |= UART_CTRL_TI;
-	UART_PUT_CTRL(port, cr);
-
-	if (UART_GET_STATUS(port) & UART_STATUS_THE)
-		apbuart_tx_chars(port);
-}
-
-static void apbuart_stop_rx(struct uart_port *port)
-{
-	unsigned int cr;
-
-	cr = UART_GET_CTRL(port);
-	cr &= ~(UART_CTRL_RI);
-	UART_PUT_CTRL(port, cr);
-}
-
-static void apbuart_enable_ms(struct uart_port *port)
-{
-	/* No modem status change interrupts for APBUART */
-}
-
-static void apbuart_rx_chars(struct uart_port *port)
-{
-	struct tty_struct *tty = port->state->port.tty;
-	unsigned int status, ch, rsr, flag;
-	unsigned int max_chars = port->fifosize;
-
-	status = UART_GET_STATUS(port);
-
-	while (UART_RX_DATA(status) && (max_chars--)) {
-
-		ch = UART_GET_CHAR(port);
-		flag = TTY_NORMAL;
-
-		port->icount.rx++;
-
-		rsr = UART_GET_STATUS(port) | UART_DUMMY_RSR_RX;
-		UART_PUT_STATUS(port, 0);
-		if (rsr & UART_STATUS_ERR) {
-
-			if (rsr & UART_STATUS_BR) {
-				rsr &= ~(UART_STATUS_FE | UART_STATUS_PE);
-				port->icount.brk++;
-				if (uart_handle_break(port))
-					goto ignore_char;
-			} else if (rsr & UART_STATUS_PE) {
-				port->icount.parity++;
-			} else if (rsr & UART_STATUS_FE) {
-				port->icount.frame++;
-			}
-			if (rsr & UART_STATUS_OE)
-				port->icount.overrun++;
-
-			rsr &= port->read_status_mask;
-
-			if (rsr & UART_STATUS_PE)
-				flag = TTY_PARITY;
-			else if (rsr & UART_STATUS_FE)
-				flag = TTY_FRAME;
-		}
-
-		if (uart_handle_sysrq_char(port, ch))
-			goto ignore_char;
-
-		uart_insert_char(port, rsr, UART_STATUS_OE, ch, flag);
-
-
-	      ignore_char:
-		status = UART_GET_STATUS(port);
-	}
-
-	tty_flip_buffer_push(tty);
-}
-
-static void apbuart_tx_chars(struct uart_port *port)
-{
-	struct circ_buf *xmit = &port->state->xmit;
-	int count;
-
-	if (port->x_char) {
-		UART_PUT_CHAR(port, port->x_char);
-		port->icount.tx++;
-		port->x_char = 0;
-		return;
-	}
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
-		apbuart_stop_tx(port);
-		return;
-	}
-
-	/* amba: fill FIFO */
-	count = port->fifosize >> 1;
-	do {
-		UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		port->icount.tx++;
-		if (uart_circ_empty(xmit))
-			break;
-	} while (--count > 0);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(port);
-
-	if (uart_circ_empty(xmit))
-		apbuart_stop_tx(port);
-}
-
-static irqreturn_t apbuart_int(int irq, void *dev_id)
-{
-	struct uart_port *port = dev_id;
-	unsigned int status;
-
-	spin_lock(&port->lock);
-
-	status = UART_GET_STATUS(port);
-	if (status & UART_STATUS_DR)
-		apbuart_rx_chars(port);
-	if (status & UART_STATUS_THE)
-		apbuart_tx_chars(port);
-
-	spin_unlock(&port->lock);
-
-	return IRQ_HANDLED;
-}
-
-static unsigned int apbuart_tx_empty(struct uart_port *port)
-{
-	unsigned int status = UART_GET_STATUS(port);
-	return status & UART_STATUS_THE ? TIOCSER_TEMT : 0;
-}
-
-static unsigned int apbuart_get_mctrl(struct uart_port *port)
-{
-	/* The GRLIB APBUART handles flow control in hardware */
-	return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
-}
-
-static void apbuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	/* The GRLIB APBUART handles flow control in hardware */
-}
-
-static void apbuart_break_ctl(struct uart_port *port, int break_state)
-{
-	/* We don't support sending break */
-}
-
-static int apbuart_startup(struct uart_port *port)
-{
-	int retval;
-	unsigned int cr;
-
-	/* Allocate the IRQ */
-	retval = request_irq(port->irq, apbuart_int, 0, "apbuart", port);
-	if (retval)
-		return retval;
-
-	/* Finally, enable interrupts */
-	cr = UART_GET_CTRL(port);
-	UART_PUT_CTRL(port,
-		      cr | UART_CTRL_RE | UART_CTRL_TE |
-		      UART_CTRL_RI | UART_CTRL_TI);
-
-	return 0;
-}
-
-static void apbuart_shutdown(struct uart_port *port)
-{
-	unsigned int cr;
-
-	/* disable all interrupts, disable the port */
-	cr = UART_GET_CTRL(port);
-	UART_PUT_CTRL(port,
-		      cr & ~(UART_CTRL_RE | UART_CTRL_TE |
-			     UART_CTRL_RI | UART_CTRL_TI));
-
-	/* Free the interrupt */
-	free_irq(port->irq, port);
-}
-
-static void apbuart_set_termios(struct uart_port *port,
-				struct ktermios *termios, struct ktermios *old)
-{
-	unsigned int cr;
-	unsigned long flags;
-	unsigned int baud, quot;
-
-	/* Ask the core to calculate the divisor for us. */
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
-	if (baud == 0)
-		panic("invalid baudrate %i\n", port->uartclk / 16);
-
-	/* uart_get_divisor calc a *16 uart freq, apbuart is *8 */
-	quot = (uart_get_divisor(port, baud)) * 2;
-	cr = UART_GET_CTRL(port);
-	cr &= ~(UART_CTRL_PE | UART_CTRL_PS);
-
-	if (termios->c_cflag & PARENB) {
-		cr |= UART_CTRL_PE;
-		if ((termios->c_cflag & PARODD))
-			cr |= UART_CTRL_PS;
-	}
-
-	/* Enable flow control. */
-	if (termios->c_cflag & CRTSCTS)
-		cr |= UART_CTRL_FL;
-
-	spin_lock_irqsave(&port->lock, flags);
-
-	/* Update the per-port timeout. */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	port->read_status_mask = UART_STATUS_OE;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= UART_STATUS_FE | UART_STATUS_PE;
-
-	/* Characters to ignore */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= UART_STATUS_FE | UART_STATUS_PE;
-
-	/* Ignore all characters if CREAD is not set. */
-	if ((termios->c_cflag & CREAD) == 0)
-		port->ignore_status_mask |= UART_DUMMY_RSR_RX;
-
-	/* Set baud rate */
-	quot -= 1;
-	UART_PUT_SCAL(port, quot);
-	UART_PUT_CTRL(port, cr);
-
-	spin_unlock_irqrestore(&port->lock, flags);
-}
-
-static const char *apbuart_type(struct uart_port *port)
-{
-	return port->type == PORT_APBUART ? "GRLIB/APBUART" : NULL;
-}
-
-static void apbuart_release_port(struct uart_port *port)
-{
-	release_mem_region(port->mapbase, 0x100);
-}
-
-static int apbuart_request_port(struct uart_port *port)
-{
-	return request_mem_region(port->mapbase, 0x100, "grlib-apbuart")
-	    != NULL ? 0 : -EBUSY;
-	return 0;
-}
-
-/* Configure/autoconfigure the port */
-static void apbuart_config_port(struct uart_port *port, int flags)
-{
-	if (flags & UART_CONFIG_TYPE) {
-		port->type = PORT_APBUART;
-		apbuart_request_port(port);
-	}
-}
-
-/* Verify the new serial_struct (for TIOCSSERIAL) */
-static int apbuart_verify_port(struct uart_port *port,
-			       struct serial_struct *ser)
-{
-	int ret = 0;
-	if (ser->type != PORT_UNKNOWN && ser->type != PORT_APBUART)
-		ret = -EINVAL;
-	if (ser->irq < 0 || ser->irq >= NR_IRQS)
-		ret = -EINVAL;
-	if (ser->baud_base < 9600)
-		ret = -EINVAL;
-	return ret;
-}
-
-static struct uart_ops grlib_apbuart_ops = {
-	.tx_empty = apbuart_tx_empty,
-	.set_mctrl = apbuart_set_mctrl,
-	.get_mctrl = apbuart_get_mctrl,
-	.stop_tx = apbuart_stop_tx,
-	.start_tx = apbuart_start_tx,
-	.stop_rx = apbuart_stop_rx,
-	.enable_ms = apbuart_enable_ms,
-	.break_ctl = apbuart_break_ctl,
-	.startup = apbuart_startup,
-	.shutdown = apbuart_shutdown,
-	.set_termios = apbuart_set_termios,
-	.type = apbuart_type,
-	.release_port = apbuart_release_port,
-	.request_port = apbuart_request_port,
-	.config_port = apbuart_config_port,
-	.verify_port = apbuart_verify_port,
-};
-
-static struct uart_port grlib_apbuart_ports[UART_NR];
-static struct device_node *grlib_apbuart_nodes[UART_NR];
-
-static int apbuart_scan_fifo_size(struct uart_port *port, int portnumber)
-{
-	int ctrl, loop = 0;
-	int status;
-	int fifosize;
-	unsigned long flags;
-
-	ctrl = UART_GET_CTRL(port);
-
-	/*
-	 * Enable the transceiver and wait for it to be ready to send data.
-	 * Clear interrupts so that this process will not be externally
-	 * interrupted in the middle (which can cause the transceiver to
-	 * drain prematurely).
-	 */
-
-	local_irq_save(flags);
-
-	UART_PUT_CTRL(port, ctrl | UART_CTRL_TE);
-
-	while (!UART_TX_READY(UART_GET_STATUS(port)))
-		loop++;
-
-	/*
-	 * Disable the transceiver so data isn't actually sent during the
-	 * actual test.
-	 */
-
-	UART_PUT_CTRL(port, ctrl & ~(UART_CTRL_TE));
-
-	fifosize = 1;
-	UART_PUT_CHAR(port, 0);
-
-	/*
-	 * So long as transmitting a character increments the tranceivier FIFO
-	 * length the FIFO must be at least that big. These bytes will
-	 * automatically drain off of the FIFO.
-	 */
-
-	status = UART_GET_STATUS(port);
-	while (((status >> 20) & 0x3F) == fifosize) {
-		fifosize++;
-		UART_PUT_CHAR(port, 0);
-		status = UART_GET_STATUS(port);
-	}
-
-	fifosize--;
-
-	UART_PUT_CTRL(port, ctrl);
-	local_irq_restore(flags);
-
-	if (fifosize == 0)
-		fifosize = 1;
-
-	return fifosize;
-}
-
-static void apbuart_flush_fifo(struct uart_port *port)
-{
-	int i;
-
-	for (i = 0; i < port->fifosize; i++)
-		UART_GET_CHAR(port);
-}
-
-
-/* ======================================================================== */
-/* Console driver, if enabled                                               */
-/* ======================================================================== */
-
-#ifdef CONFIG_SERIAL_GRLIB_GAISLER_APBUART_CONSOLE
-
-static void apbuart_console_putchar(struct uart_port *port, int ch)
-{
-	unsigned int status;
-	do {
-		status = UART_GET_STATUS(port);
-	} while (!UART_TX_READY(status));
-	UART_PUT_CHAR(port, ch);
-}
-
-static void
-apbuart_console_write(struct console *co, const char *s, unsigned int count)
-{
-	struct uart_port *port = &grlib_apbuart_ports[co->index];
-	unsigned int status, old_cr, new_cr;
-
-	/* First save the CR then disable the interrupts */
-	old_cr = UART_GET_CTRL(port);
-	new_cr = old_cr & ~(UART_CTRL_RI | UART_CTRL_TI);
-	UART_PUT_CTRL(port, new_cr);
-
-	uart_console_write(port, s, count, apbuart_console_putchar);
-
-	/*
-	 *      Finally, wait for transmitter to become empty
-	 *      and restore the TCR
-	 */
-	do {
-		status = UART_GET_STATUS(port);
-	} while (!UART_TX_READY(status));
-	UART_PUT_CTRL(port, old_cr);
-}
-
-static void __init
-apbuart_console_get_options(struct uart_port *port, int *baud,
-			    int *parity, int *bits)
-{
-	if (UART_GET_CTRL(port) & (UART_CTRL_RE | UART_CTRL_TE)) {
-
-		unsigned int quot, status;
-		status = UART_GET_STATUS(port);
-
-		*parity = 'n';
-		if (status & UART_CTRL_PE) {
-			if ((status & UART_CTRL_PS) == 0)
-				*parity = 'e';
-			else
-				*parity = 'o';
-		}
-
-		*bits = 8;
-		quot = UART_GET_SCAL(port) / 8;
-		*baud = port->uartclk / (16 * (quot + 1));
-	}
-}
-
-static int __init apbuart_console_setup(struct console *co, char *options)
-{
-	struct uart_port *port;
-	int baud = 38400;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	pr_debug("apbuart_console_setup co=%p, co->index=%i, options=%s\n",
-		 co, co->index, options);
-
-	/*
-	 * Check whether an invalid uart number has been specified, and
-	 * if so, search for the first available port that does have
-	 * console support.
-	 */
-	if (co->index >= grlib_apbuart_port_nr)
-		co->index = 0;
-
-	port = &grlib_apbuart_ports[co->index];
-
-	spin_lock_init(&port->lock);
-
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	else
-		apbuart_console_get_options(port, &baud, &parity, &bits);
-
-	return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-static struct uart_driver grlib_apbuart_driver;
-
-static struct console grlib_apbuart_console = {
-	.name = "ttyS",
-	.write = apbuart_console_write,
-	.device = uart_console_device,
-	.setup = apbuart_console_setup,
-	.flags = CON_PRINTBUFFER,
-	.index = -1,
-	.data = &grlib_apbuart_driver,
-};
-
-
-static int grlib_apbuart_configure(void);
-
-static int __init apbuart_console_init(void)
-{
-	if (grlib_apbuart_configure())
-		return -ENODEV;
-	register_console(&grlib_apbuart_console);
-	return 0;
-}
-
-console_initcall(apbuart_console_init);
-
-#define APBUART_CONSOLE	(&grlib_apbuart_console)
-#else
-#define APBUART_CONSOLE	NULL
-#endif
-
-static struct uart_driver grlib_apbuart_driver = {
-	.owner = THIS_MODULE,
-	.driver_name = "serial",
-	.dev_name = "ttyS",
-	.major = SERIAL_APBUART_MAJOR,
-	.minor = SERIAL_APBUART_MINOR,
-	.nr = UART_NR,
-	.cons = APBUART_CONSOLE,
-};
-
-
-/* ======================================================================== */
-/* OF Platform Driver                                                       */
-/* ======================================================================== */
-
-static int __devinit apbuart_probe(struct platform_device *op,
-				   const struct of_device_id *match)
-{
-	int i = -1;
-	struct uart_port *port = NULL;
-
-	i = 0;
-	for (i = 0; i < grlib_apbuart_port_nr; i++) {
-		if (op->dev.of_node == grlib_apbuart_nodes[i])
-			break;
-	}
-
-	port = &grlib_apbuart_ports[i];
-	port->dev = &op->dev;
-
-	uart_add_one_port(&grlib_apbuart_driver, (struct uart_port *) port);
-
-	apbuart_flush_fifo((struct uart_port *) port);
-
-	printk(KERN_INFO "grlib-apbuart at 0x%llx, irq %d\n",
-	       (unsigned long long) port->mapbase, port->irq);
-	return 0;
-}
-
-static struct of_device_id __initdata apbuart_match[] = {
-	{
-	 .name = "GAISLER_APBUART",
-	 },
-	{
-	 .name = "01_00c",
-	 },
-	{},
-};
-
-static struct of_platform_driver grlib_apbuart_of_driver = {
-	.probe = apbuart_probe,
-	.driver = {
-		.owner = THIS_MODULE,
-		.name = "grlib-apbuart",
-		.of_match_table = apbuart_match,
-	},
-};
-
-
-static int grlib_apbuart_configure(void)
-{
-	struct device_node *np, *rp;
-	const u32 *prop;
-	int freq_khz, line = 0;
-
-	/* Get bus frequency */
-	rp = of_find_node_by_path("/");
-	if (!rp)
-		return -ENODEV;
-	rp = of_get_next_child(rp, NULL);
-	if (!rp)
-		return -ENODEV;
-	prop = of_get_property(rp, "clock-frequency", NULL);
-	if (!prop)
-		return -ENODEV;
-	freq_khz = *prop;
-
-	for_each_matching_node(np, apbuart_match) {
-		const int *irqs, *ampopts;
-		const struct amba_prom_registers *regs;
-		struct uart_port *port;
-		unsigned long addr;
-
-		ampopts = of_get_property(np, "ampopts", NULL);
-		if (ampopts && (*ampopts == 0))
-			continue; /* Ignore if used by another OS instance */
-
-		irqs = of_get_property(np, "interrupts", NULL);
-		regs = of_get_property(np, "reg", NULL);
-
-		if (!irqs || !regs)
-			continue;
-
-		grlib_apbuart_nodes[line] = np;
-
-		addr = regs->phys_addr;
-
-		port = &grlib_apbuart_ports[line];
-
-		port->mapbase = addr;
-		port->membase = ioremap(addr, sizeof(struct grlib_apbuart_regs_map));
-		port->irq = *irqs;
-		port->iotype = UPIO_MEM;
-		port->ops = &grlib_apbuart_ops;
-		port->flags = UPF_BOOT_AUTOCONF;
-		port->line = line;
-		port->uartclk = freq_khz * 1000;
-		port->fifosize = apbuart_scan_fifo_size((struct uart_port *) port, line);
-		line++;
-
-		/* We support maximum UART_NR uarts ... */
-		if (line == UART_NR)
-			break;
-	}
-
-	grlib_apbuart_driver.nr = grlib_apbuart_port_nr = line;
-	return line ? 0 : -ENODEV;
-}
-
-static int __init grlib_apbuart_init(void)
-{
-	int ret;
-
-	/* Find all APBUARTS in device the tree and initialize their ports */
-	ret = grlib_apbuart_configure();
-	if (ret)
-		return ret;
-
-	printk(KERN_INFO "Serial: GRLIB APBUART driver\n");
-
-	ret = uart_register_driver(&grlib_apbuart_driver);
-
-	if (ret) {
-		printk(KERN_ERR "%s: uart_register_driver failed (%i)\n",
-		       __FILE__, ret);
-		return ret;
-	}
-
-	ret = of_register_platform_driver(&grlib_apbuart_of_driver);
-	if (ret) {
-		printk(KERN_ERR
-		       "%s: of_register_platform_driver failed (%i)\n",
-		       __FILE__, ret);
-		uart_unregister_driver(&grlib_apbuart_driver);
-		return ret;
-	}
-
-	return ret;
-}
-
-static void __exit grlib_apbuart_exit(void)
-{
-	int i;
-
-	for (i = 0; i < grlib_apbuart_port_nr; i++)
-		uart_remove_one_port(&grlib_apbuart_driver,
-				     &grlib_apbuart_ports[i]);
-
-	uart_unregister_driver(&grlib_apbuart_driver);
-	of_unregister_platform_driver(&grlib_apbuart_of_driver);
-}
-
-module_init(grlib_apbuart_init);
-module_exit(grlib_apbuart_exit);
-
-MODULE_AUTHOR("Aeroflex Gaisler AB");
-MODULE_DESCRIPTION("GRLIB APBUART serial driver");
-MODULE_VERSION("2.1");
-MODULE_LICENSE("GPL");