Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
  [ARM] 4578/1: CM-x270: PCMCIA support
  [ARM] 4577/1: ITE 8152 PCI bridge support
  [ARM] 4576/1: CM-X270 machine support
  [ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
  [ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
  [ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
  [ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
  [ARM] pxa: PXA3xx base support
  [NET] smc91x: fix PXA DMA support code
  [SERIAL] Fix console initialisation ordering
  [ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
  [ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
  [ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
  [ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
  [ARM] Rename consistent_sync() as dma_cache_maint()
  [ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
  [ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
  [ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
  [ARM] 4594/1: ns9xxx: use the new gpio functions
  [ARM] 4593/1: ns9xxx: implement generic clockevents
  ...

2 files changed, 91 insertions, 90 deletions

diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c
index e9c6cb391a2..af3a011b2b2 100644
--- a/drivers/serial/pxa.c
+++ b/drivers/serial/pxa.c
@@ -42,6 +42,7 @@
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
 #include <linux/serial_core.h>
+#include <linux/clk.h>
 
 #include <asm/io.h>
 #include <asm/hardware.h>
@@ -55,7 +56,7 @@ struct uart_pxa_port {
 	unsigned char           lcr;
 	unsigned char           mcr;
 	unsigned int            lsr_break_flag;
-	unsigned int		cken;
+	struct clk		*clk;
 	char			*name;
 };
 
@@ -351,6 +352,8 @@ static int serial_pxa_startup(struct uart_port *port)
 	else
 		up->mcr = 0;
 
+	up->port.uartclk = clk_get_rate(up->clk);
+
 	/*
 	 * Allocate the IRQ
 	 */
@@ -546,9 +549,11 @@ serial_pxa_pm(struct uart_port *port, unsigned int state,
 	      unsigned int oldstate)
 {
 	struct uart_pxa_port *up = (struct uart_pxa_port *)port;
-	pxa_set_cken(up->cken, !state);
+
 	if (!state)
-		udelay(1);
+		clk_enable(up->clk);
+	else
+		clk_disable(up->clk);
 }
 
 static void serial_pxa_release_port(struct uart_port *port)
@@ -582,7 +587,7 @@ serial_pxa_type(struct uart_port *port)
 
 #ifdef CONFIG_SERIAL_PXA_CONSOLE
 
-static struct uart_pxa_port serial_pxa_ports[];
+static struct uart_pxa_port *serial_pxa_ports[4];
 static struct uart_driver serial_pxa_reg;
 
 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
@@ -632,9 +637,11 @@ static void serial_pxa_console_putchar(struct uart_port *port, int ch)
 static void
 serial_pxa_console_write(struct console *co, const char *s, unsigned int count)
 {
-	struct uart_pxa_port *up = &serial_pxa_ports[co->index];
+	struct uart_pxa_port *up = serial_pxa_ports[co->index];
 	unsigned int ier;
 
+	clk_enable(up->clk);
+
 	/*
 	 *	First save the IER then disable the interrupts
 	 */
@@ -649,6 +656,8 @@ serial_pxa_console_write(struct console *co, const char *s, unsigned int count)
 	 */
 	wait_for_xmitr(up);
 	serial_out(up, UART_IER, ier);
+
+	clk_disable(up->clk);
 }
 
 static int __init
@@ -662,7 +671,9 @@ serial_pxa_console_setup(struct console *co, char *options)
 
 	if (co->index == -1 || co->index >= serial_pxa_reg.nr)
 		co->index = 0;
-       	up = &serial_pxa_ports[co->index];
+	up = serial_pxa_ports[co->index];
+	if (!up)
+		return -ENODEV;
 
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -680,15 +691,6 @@ static struct console serial_pxa_console = {
 	.data		= &serial_pxa_reg,
 };
 
-static int __init
-serial_pxa_console_init(void)
-{
-	register_console(&serial_pxa_console);
-	return 0;
-}
-
-console_initcall(serial_pxa_console_init);
-
 #define PXA_CONSOLE	&serial_pxa_console
 #else
 #define PXA_CONSOLE	NULL
@@ -714,73 +716,13 @@ struct uart_ops serial_pxa_pops = {
 	.verify_port	= serial_pxa_verify_port,
 };
 
-static struct uart_pxa_port serial_pxa_ports[] = {
-     {	/* FFUART */
-	.name	= "FFUART",
-	.cken	= CKEN_FFUART,
-	.port	= {
-		.type		= PORT_PXA,
-		.iotype		= UPIO_MEM,
-		.membase	= (void *)&FFUART,
-		.mapbase	= __PREG(FFUART),
-		.irq		= IRQ_FFUART,
-		.uartclk	= 921600 * 16,
-		.fifosize	= 64,
-		.ops		= &serial_pxa_pops,
-		.line		= 0,
-	},
-  }, {	/* BTUART */
-	.name	= "BTUART",
-	.cken	= CKEN_BTUART,
-	.port	= {
-		.type		= PORT_PXA,
-		.iotype		= UPIO_MEM,
-		.membase	= (void *)&BTUART,
-		.mapbase	= __PREG(BTUART),
-		.irq		= IRQ_BTUART,
-		.uartclk	= 921600 * 16,
-		.fifosize	= 64,
-		.ops		= &serial_pxa_pops,
-		.line		= 1,
-	},
-  }, {	/* STUART */
-	.name	= "STUART",
-	.cken	= CKEN_STUART,
-	.port	= {
-		.type		= PORT_PXA,
-		.iotype		= UPIO_MEM,
-		.membase	= (void *)&STUART,
-		.mapbase	= __PREG(STUART),
-		.irq		= IRQ_STUART,
-		.uartclk	= 921600 * 16,
-		.fifosize	= 64,
-		.ops		= &serial_pxa_pops,
-		.line		= 2,
-	},
-  }, {  /* HWUART */
-	.name	= "HWUART",
-	.cken	= CKEN_HWUART,
-	.port = {
-		.type		= PORT_PXA,
-		.iotype		= UPIO_MEM,
-		.membase	= (void *)&HWUART,
-		.mapbase	= __PREG(HWUART),
-		.irq		= IRQ_HWUART,
-		.uartclk	= 921600 * 16,
-		.fifosize	= 64,
-		.ops		= &serial_pxa_pops,
-		.line		= 3,
-	},
-  }
-};
-
 static struct uart_driver serial_pxa_reg = {
 	.owner		= THIS_MODULE,
 	.driver_name	= "PXA serial",
 	.dev_name	= "ttyS",
 	.major		= TTY_MAJOR,
 	.minor		= 64,
-	.nr		= ARRAY_SIZE(serial_pxa_ports),
+	.nr		= 4,
 	.cons		= PXA_CONSOLE,
 };
 
@@ -806,10 +748,68 @@ static int serial_pxa_resume(struct platform_device *dev)
 
 static int serial_pxa_probe(struct platform_device *dev)
 {
-	serial_pxa_ports[dev->id].port.dev = &dev->dev;
-	uart_add_one_port(&serial_pxa_reg, &serial_pxa_ports[dev->id].port);
-	platform_set_drvdata(dev, &serial_pxa_ports[dev->id]);
+	struct uart_pxa_port *sport;
+	struct resource *mmres, *irqres;
+	int ret;
+
+	mmres = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	irqres = platform_get_resource(dev, IORESOURCE_IRQ, 0);
+	if (!mmres || !irqres)
+		return -ENODEV;
+
+	sport = kzalloc(sizeof(struct uart_pxa_port), GFP_KERNEL);
+	if (!sport)
+		return -ENOMEM;
+
+	sport->clk = clk_get(&dev->dev, "UARTCLK");
+	if (IS_ERR(sport->clk)) {
+		ret = PTR_ERR(sport->clk);
+		goto err_free;
+	}
+
+	sport->port.type = PORT_PXA;
+	sport->port.iotype = UPIO_MEM;
+	sport->port.mapbase = mmres->start;
+	sport->port.irq = irqres->start;
+	sport->port.fifosize = 64;
+	sport->port.ops = &serial_pxa_pops;
+	sport->port.line = dev->id;
+	sport->port.dev = &dev->dev;
+	sport->port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
+	sport->port.uartclk = clk_get_rate(sport->clk);
+
+	/*
+	 * Is it worth keeping this?
+	 */
+	if (mmres->start == __PREG(FFUART))
+		sport->name = "FFUART";
+	else if (mmres->start == __PREG(BTUART))
+		sport->name = "BTUART";
+	else if (mmres->start == __PREG(STUART))
+		sport->name = "STUART";
+	else if (mmres->start == __PREG(HWUART))
+		sport->name = "HWUART";
+	else
+		sport->name = "???";
+
+	sport->port.membase = ioremap(mmres->start, mmres->end - mmres->start + 1);
+	if (!sport->port.membase) {
+		ret = -ENOMEM;
+		goto err_clk;
+	}
+
+	serial_pxa_ports[dev->id] = sport;
+
+	uart_add_one_port(&serial_pxa_reg, &sport->port);
+	platform_set_drvdata(dev, sport);
+
 	return 0;
+
+ err_clk:
+	clk_put(sport->clk);
+ err_free:
+	kfree(sport);
+	return ret;
 }
 
 static int serial_pxa_remove(struct platform_device *dev)
@@ -818,8 +818,9 @@ static int serial_pxa_remove(struct platform_device *dev)
 
 	platform_set_drvdata(dev, NULL);
 
-	if (sport)
-		uart_remove_one_port(&serial_pxa_reg, &sport->port);
+	uart_remove_one_port(&serial_pxa_reg, &sport->port);
+	clk_put(sport->clk);
+	kfree(sport);
 
 	return 0;
 }
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index a055f58f342..a3bd3a3f41f 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2127,6 +2127,14 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 		spin_unlock_irqrestore(&port->lock, flags);
 
 		/*
+		 * If this driver supports console, and it hasn't been
+		 * successfully registered yet, try to re-register it.
+		 * It may be that the port was not available.
+		 */
+		if (port->cons && !(port->cons->flags & CON_ENABLED))
+			register_console(port->cons);
+
+		/*
 		 * Power down all ports by default, except the
 		 * console if we have one.
 		 */
@@ -2286,6 +2294,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port)
 	}
 
 	state->port = port;
+	state->pm_state = -1;
 
 	port->cons = drv->cons;
 	port->info = state->info;
@@ -2308,15 +2317,6 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *port)
 	tty_register_device(drv->tty_driver, port->line, port->dev);
 
 	/*
-	 * If this driver supports console, and it hasn't been
-	 * successfully registered yet, try to re-register it.
-	 * It may be that the port was not available.
-	 */
-	if (port->type != PORT_UNKNOWN &&
-	    port->cons && !(port->cons->flags & CON_ENABLED))
-		register_console(port->cons);
-
-	/*
 	 * Ensure UPF_DEAD is not set.
 	 */
 	port->flags &= ~UPF_DEAD;