Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull TTY changes from Greg Kroah-Hartman:
 "As we skipped the merge window for 3.6-rc1 for the tty tree,
  everything is now settled down and working properly, so we are ready
  for 3.7-rc1.  Here's the patchset, it's big, but the large changes are
  removing a firmware file and adding a staging tty driver (it depended
  on the tty core changes, so it's going through this tree instead of
  the staging tree.)

  All of these patches have been in the linux-next tree for a while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up more-or-less trivial conflicts in
 - drivers/char/pcmcia/synclink_cs.c:
    tty NULL dereference fix vs tty_port_cts_enabled() helper function
 - drivers/staging/{Kconfig,Makefile}:
    add-add conflict (dgrp driver added close to other staging drivers)
 - drivers/staging/ipack/devices/ipoctal.c:
    "split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"

* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
  tty/serial: Add kgdb_nmi driver
  tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
  tty/serial/amba-pl011: Implement poll_init callback
  tty/serial/core: Introduce poll_init callback
  kdb: Turn KGDB_KDB=n stubs into static inlines
  kdb: Implement disable_nmi command
  kernel/debug: Mask KGDB NMI upon entry
  serial: pl011: handle corruption at high clock speeds
  serial: sccnxp: Make 'default' choice in switch last
  serial: sccnxp: Remove mask termios caps for SW flow control
  serial: sccnxp: Report actual baudrate back to core
  serial: samsung: Add poll_get_char & poll_put_char
  Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
  Powerpc 8xx CPM_UART maxidl should not depend on fifo size
  Powerpc 8xx CPM_UART too many interrupts
  Powerpc 8xx CPM_UART desynchronisation
  serial: set correct baud_base for EXSYS EX-41092 Dual 16950
  serial: omap: fix the reciever line error case
  8250: blacklist Winbond CIR port
  8250_pnp: do pnp probe before legacy probe
  ...

1 files changed, 15 insertions, 15 deletions

diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c
index 29b695d041e..b7d48b34639 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -73,7 +73,7 @@ struct serial_quirk {
 	unsigned int prodid;
 	int multi;		/* 1 = multifunction, > 1 = # ports */
 	void (*config)(struct pcmcia_device *);
-	void (*setup)(struct pcmcia_device *, struct uart_port *);
+	void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
 	void (*wakeup)(struct pcmcia_device *);
 	int (*post)(struct pcmcia_device *);
 };
@@ -105,9 +105,9 @@ struct serial_cfg_mem {
  * Elan VPU16551 UART with 14.7456MHz oscillator
  * manfid 0x015D, 0x4C45
  */
-static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port)
+static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
 {
-	port->uartclk = 14745600;
+	uart->port.uartclk = 14745600;
 }
 
 static int quirk_post_ibm(struct pcmcia_device *link)
@@ -343,25 +343,25 @@ static void serial_detach(struct pcmcia_device *link)
 static int setup_serial(struct pcmcia_device *handle, struct serial_info * info,
 			unsigned int iobase, int irq)
 {
-	struct uart_port port;
+	struct uart_8250_port uart;
 	int line;
 
-	memset(&port, 0, sizeof (struct uart_port));
-	port.iobase = iobase;
-	port.irq = irq;
-	port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
-	port.uartclk = 1843200;
-	port.dev = &handle->dev;
+	memset(&uart, 0, sizeof(uart));
+	uart.port.iobase = iobase;
+	uart.port.irq = irq;
+	uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
+	uart.port.uartclk = 1843200;
+	uart.port.dev = &handle->dev;
 	if (buggy_uart)
-		port.flags |= UPF_BUGGY_UART;
+		uart.port.flags |= UPF_BUGGY_UART;
 
 	if (info->quirk && info->quirk->setup)
-		info->quirk->setup(handle, &port);
+		info->quirk->setup(handle, &uart);
 
-	line = serial8250_register_port(&port);
+	line = serial8250_register_8250_port(&uart);
 	if (line < 0) {
-		printk(KERN_NOTICE "serial_cs: serial8250_register_port() at "
-		       "0x%04lx, irq %d failed\n", (u_long)iobase, irq);
+		pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
+							(unsigned long)iobase, irq);
 		return -EINVAL;
 	}