Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 4139 insertions, 0 deletions

diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
new file mode 100644
index 00000000000..4857f0e4ef4
--- /dev/null
+++ b/drivers/usb/gadget/file_storage.c
@@ -0,0 +1,4139 @@
+/*
+ * file_storage.c -- File-backed USB Storage Gadget, for USB development
+ *
+ * Copyright (C) 2003-2005 Alan Stern
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions, and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in the
+ *    documentation and/or other materials provided with the distribution.
+ * 3. The names of the above-listed copyright holders may not be used
+ *    to endorse or promote products derived from this software without
+ *    specific prior written permission.
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+
+/*
+ * The File-backed Storage Gadget acts as a USB Mass Storage device,
+ * appearing to the host as a disk drive.  In addition to providing an
+ * example of a genuinely useful gadget driver for a USB device, it also
+ * illustrates a technique of double-buffering for increased throughput.
+ * Last but not least, it gives an easy way to probe the behavior of the
+ * Mass Storage drivers in a USB host.
+ *
+ * Backing storage is provided by a regular file or a block device, specified
+ * by the "file" module parameter.  Access can be limited to read-only by
+ * setting the optional "ro" module parameter.  The gadget will indicate that
+ * it has removable media if the optional "removable" module parameter is set.
+ *
+ * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
+ * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
+ * by the optional "transport" module parameter.  It also supports the
+ * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
+ * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
+ * the optional "protocol" module parameter.  In addition, the default
+ * Vendor ID, Product ID, and release number can be overridden.
+ *
+ * There is support for multiple logical units (LUNs), each of which has
+ * its own backing file.  The number of LUNs can be set using the optional
+ * "luns" module parameter (anywhere from 1 to 8), and the corresponding
+ * files are specified using comma-separated lists for "file" and "ro".
+ * The default number of LUNs is taken from the number of "file" elements;
+ * it is 1 if "file" is not given.  If "removable" is not set then a backing
+ * file must be specified for each LUN.  If it is set, then an unspecified
+ * or empty backing filename means the LUN's medium is not loaded.
+ *
+ * Requirements are modest; only a bulk-in and a bulk-out endpoint are
+ * needed (an interrupt-out endpoint is also needed for CBI).  The memory
+ * requirement amounts to two 16K buffers, size configurable by a parameter.
+ * Support is included for both full-speed and high-speed operation.
+ *
+ * Module options:
+ *
+ *	file=filename[,filename...]
+ *				Required if "removable" is not set, names of
+ *					the files or block devices used for
+ *					backing storage
+ *	ro=b[,b...]		Default false, booleans for read-only access
+ *	removable		Default false, boolean for removable media
+ *	luns=N			Default N = number of filenames, number of
+ *					LUNs to support
+ *	transport=XXX		Default BBB, transport name (CB, CBI, or BBB)
+ *	protocol=YYY		Default SCSI, protocol name (RBC, 8020 or
+ *					ATAPI, QIC, UFI, 8070, or SCSI;
+ *					also 1 - 6)
+ *	vendor=0xVVVV		Default 0x0525 (NetChip), USB Vendor ID
+ *	product=0xPPPP		Default 0xa4a5 (FSG), USB Product ID
+ *	release=0xRRRR		Override the USB release number (bcdDevice)
+ *	buflen=N		Default N=16384, buffer size used (will be
+ *					rounded down to a multiple of
+ *					PAGE_CACHE_SIZE)
+ *	stall			Default determined according to the type of
+ *					USB device controller (usually true),
+ *					boolean to permit the driver to halt
+ *					bulk endpoints
+ *
+ * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "ro",
+ * "removable", and "luns" options are available; default values are used
+ * for everything else.
+ *
+ * The pathnames of the backing files and the ro settings are available in
+ * the attribute files "file" and "ro" in the lun<n> subdirectory of the
+ * gadget's sysfs directory.  If the "removable" option is set, writing to
+ * these files will simulate ejecting/loading the medium (writing an empty
+ * line means eject) and adjusting a write-enable tab.  Changes to the ro
+ * setting are not allowed when the medium is loaded.
+ *
+ * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
+ */
+
+
+/*
+ *				Driver Design
+ *
+ * The FSG driver is fairly straightforward.  There is a main kernel
+ * thread that handles most of the work.  Interrupt routines field
+ * callbacks from the controller driver: bulk- and interrupt-request
+ * completion notifications, endpoint-0 events, and disconnect events.
+ * Completion events are passed to the main thread by wakeup calls.  Many
+ * ep0 requests are handled at interrupt time, but SetInterface,
+ * SetConfiguration, and device reset requests are forwarded to the
+ * thread in the form of "exceptions" using SIGUSR1 signals (since they
+ * should interrupt any ongoing file I/O operations).
+ *
+ * The thread's main routine implements the standard command/data/status
+ * parts of a SCSI interaction.  It and its subroutines are full of tests
+ * for pending signals/exceptions -- all this polling is necessary since
+ * the kernel has no setjmp/longjmp equivalents.  (Maybe this is an
+ * indication that the driver really wants to be running in userspace.)
+ * An important point is that so long as the thread is alive it keeps an
+ * open reference to the backing file.  This will prevent unmounting
+ * the backing file's underlying filesystem and could cause problems
+ * during system shutdown, for example.  To prevent such problems, the
+ * thread catches INT, TERM, and KILL signals and converts them into
+ * an EXIT exception.
+ *
+ * In normal operation the main thread is started during the gadget's
+ * fsg_bind() callback and stopped during fsg_unbind().  But it can also
+ * exit when it receives a signal, and there's no point leaving the
+ * gadget running when the thread is dead.  So just before the thread
+ * exits, it deregisters the gadget driver.  This makes things a little
+ * tricky: The driver is deregistered at two places, and the exiting
+ * thread can indirectly call fsg_unbind() which in turn can tell the
+ * thread to exit.  The first problem is resolved through the use of the
+ * REGISTERED atomic bitflag; the driver will only be deregistered once.
+ * The second problem is resolved by having fsg_unbind() check
+ * fsg->state; it won't try to stop the thread if the state is already
+ * FSG_STATE_TERMINATED.
+ *
+ * To provide maximum throughput, the driver uses a circular pipeline of
+ * buffer heads (struct fsg_buffhd).  In principle the pipeline can be
+ * arbitrarily long; in practice the benefits don't justify having more
+ * than 2 stages (i.e., double buffering).  But it helps to think of the
+ * pipeline as being a long one.  Each buffer head contains a bulk-in and
+ * a bulk-out request pointer (since the buffer can be used for both
+ * output and input -- directions always are given from the host's
+ * point of view) as well as a pointer to the buffer and various state
+ * variables.
+ *
+ * Use of the pipeline follows a simple protocol.  There is a variable
+ * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
+ * At any time that buffer head may still be in use from an earlier
+ * request, so each buffer head has a state variable indicating whether
+ * it is EMPTY, FULL, or BUSY.  Typical use involves waiting for the
+ * buffer head to be EMPTY, filling the buffer either by file I/O or by
+ * USB I/O (during which the buffer head is BUSY), and marking the buffer
+ * head FULL when the I/O is complete.  Then the buffer will be emptied
+ * (again possibly by USB I/O, during which it is marked BUSY) and
+ * finally marked EMPTY again (possibly by a completion routine).
+ *
+ * A module parameter tells the driver to avoid stalling the bulk
+ * endpoints wherever the transport specification allows.  This is
+ * necessary for some UDCs like the SuperH, which cannot reliably clear a
+ * halt on a bulk endpoint.  However, under certain circumstances the
+ * Bulk-only specification requires a stall.  In such cases the driver
+ * will halt the endpoint and set a flag indicating that it should clear
+ * the halt in software during the next device reset.  Hopefully this
+ * will permit everything to work correctly.  Furthermore, although the
+ * specification allows the bulk-out endpoint to halt when the host sends
+ * too much data, implementing this would cause an unavoidable race.
+ * The driver will always use the "no-stall" approach for OUT transfers.
+ *
+ * One subtle point concerns sending status-stage responses for ep0
+ * requests.  Some of these requests, such as device reset, can involve
+ * interrupting an ongoing file I/O operation, which might take an
+ * arbitrarily long time.  During that delay the host might give up on
+ * the original ep0 request and issue a new one.  When that happens the
+ * driver should not notify the host about completion of the original
+ * request, as the host will no longer be waiting for it.  So the driver
+ * assigns to each ep0 request a unique tag, and it keeps track of the
+ * tag value of the request associated with a long-running exception
+ * (device-reset, interface-change, or configuration-change).  When the
+ * exception handler is finished, the status-stage response is submitted
+ * only if the current ep0 request tag is equal to the exception request
+ * tag.  Thus only the most recently received ep0 request will get a
+ * status-stage response.
+ *
+ * Warning: This driver source file is too long.  It ought to be split up
+ * into a header file plus about 3 separate .c files, to handle the details
+ * of the Gadget, USB Mass Storage, and SCSI protocols.
+ */
+
+
+#undef DEBUG
+#undef VERBOSE
+#undef DUMP_MSGS
+
+#include <linux/config.h>
+
+#include <asm/system.h>
+#include <asm/uaccess.h>
+
+#include <linux/bitops.h>
+#include <linux/blkdev.h>
+#include <linux/compiler.h>
+#include <linux/completion.h>
+#include <linux/dcache.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/fcntl.h>
+#include <linux/file.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/limits.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/pagemap.h>
+#include <linux/rwsem.h>
+#include <linux/sched.h>
+#include <linux/signal.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/suspend.h>
+#include <linux/utsname.h>
+#include <linux/wait.h>
+
+#include <linux/usb_ch9.h>
+#include <linux/usb_gadget.h>
+
+#include "gadget_chips.h"
+
+
+/*-------------------------------------------------------------------------*/
+
+#define DRIVER_DESC		"File-backed Storage Gadget"
+#define DRIVER_NAME		"g_file_storage"
+#define DRIVER_VERSION		"20 October 2004"
+
+static const char longname[] = DRIVER_DESC;
+static const char shortname[] = DRIVER_NAME;
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_AUTHOR("Alan Stern");
+MODULE_LICENSE("Dual BSD/GPL");
+
+/* Thanks to NetChip Technologies for donating this product ID.
+ *
+ * DO NOT REUSE THESE IDs with any other driver!!  Ever!!
+ * Instead:  allocate your own, using normal USB-IF procedures. */
+#define DRIVER_VENDOR_ID	0x0525	// NetChip
+#define DRIVER_PRODUCT_ID	0xa4a5	// Linux-USB File-backed Storage Gadget
+
+
+/*
+ * This driver assumes self-powered hardware and has no way for users to
+ * trigger remote wakeup.  It uses autoconfiguration to select endpoints
+ * and endpoint addresses.
+ */
+
+
+/*-------------------------------------------------------------------------*/
+
+#define xprintk(f,level,fmt,args...) \
+	dev_printk(level , &(f)->gadget->dev , fmt , ## args)
+#define yprintk(l,level,fmt,args...) \
+	dev_printk(level , &(l)->dev , fmt , ## args)
+
+#ifdef DEBUG
+#define DBG(fsg,fmt,args...) \
+	xprintk(fsg , KERN_DEBUG , fmt , ## args)
+#define LDBG(lun,fmt,args...) \
+	yprintk(lun , KERN_DEBUG , fmt , ## args)
+#define MDBG(fmt,args...) \
+	printk(KERN_DEBUG DRIVER_NAME ": " fmt , ## args)
+#else
+#define DBG(fsg,fmt,args...) \
+	do { } while (0)
+#define LDBG(lun,fmt,args...) \
+	do { } while (0)
+#define MDBG(fmt,args...) \
+	do { } while (0)
+#undef VERBOSE
+#undef DUMP_MSGS
+#endif /* DEBUG */
+
+#ifdef VERBOSE
+#define VDBG	DBG
+#define VLDBG	LDBG
+#else
+#define VDBG(fsg,fmt,args...) \
+	do { } while (0)
+#define VLDBG(lun,fmt,args...) \
+	do { } while (0)
+#endif /* VERBOSE */
+
+#define ERROR(fsg,fmt,args...) \
+	xprintk(fsg , KERN_ERR , fmt , ## args)
+#define LERROR(lun,fmt,args...) \
+	yprintk(lun , KERN_ERR , fmt , ## args)
+
+#define WARN(fsg,fmt,args...) \
+	xprintk(fsg , KERN_WARNING , fmt , ## args)
+#define LWARN(lun,fmt,args...) \
+	yprintk(lun , KERN_WARNING , fmt , ## args)
+
+#define INFO(fsg,fmt,args...) \
+	xprintk(fsg , KERN_INFO , fmt , ## args)
+#define LINFO(lun,fmt,args...) \
+	yprintk(lun , KERN_INFO , fmt , ## args)
+
+#define MINFO(fmt,args...) \
+	printk(KERN_INFO DRIVER_NAME ": " fmt , ## args)
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Encapsulate the module parameter settings */
+
+#define MAX_LUNS	8
+
+	/* Arggh!  There should be a module_param_array_named macro! */
+static char		*file[MAX_LUNS] = {NULL, };
+static int		ro[MAX_LUNS] = {0, };
+
+static struct {
+	int		num_filenames;
+	int		num_ros;
+	unsigned int	nluns;
+
+	char		*transport_parm;
+	char		*protocol_parm;
+	int		removable;
+	unsigned short	vendor;
+	unsigned short	product;
+	unsigned short	release;
+	unsigned int	buflen;
+	int		can_stall;
+
+	int		transport_type;
+	char		*transport_name;
+	int		protocol_type;
+	char		*protocol_name;
+
+} mod_data = {					// Default values
+	.transport_parm		= "BBB",
+	.protocol_parm		= "SCSI",
+	.removable		= 0,
+	.vendor			= DRIVER_VENDOR_ID,
+	.product		= DRIVER_PRODUCT_ID,
+	.release		= 0xffff,	// Use controller chip type
+	.buflen			= 16384,
+	.can_stall		= 1,
+	};
+
+
+module_param_array(file, charp, &mod_data.num_filenames, S_IRUGO);
+MODULE_PARM_DESC(file, "names of backing files or devices");
+
+module_param_array(ro, bool, &mod_data.num_ros, S_IRUGO);
+MODULE_PARM_DESC(ro, "true to force read-only");
+
+module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
+MODULE_PARM_DESC(luns, "number of LUNs");
+
+module_param_named(removable, mod_data.removable, bool, S_IRUGO);
+MODULE_PARM_DESC(removable, "true to simulate removable media");
+
+
+/* In the non-TEST version, only the module parameters listed above
+ * are available. */
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+
+module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
+MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");
+
+module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
+MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
+		"8070, or SCSI)");
+
+module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
+MODULE_PARM_DESC(vendor, "USB Vendor ID");
+
+module_param_named(product, mod_data.product, ushort, S_IRUGO);
+MODULE_PARM_DESC(product, "USB Product ID");
+
+module_param_named(release, mod_data.release, ushort, S_IRUGO);
+MODULE_PARM_DESC(release, "USB release number");
+
+module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
+MODULE_PARM_DESC(buflen, "I/O buffer size");
+
+module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
+MODULE_PARM_DESC(stall, "false to prevent bulk stalls");
+
+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
+
+
+/*-------------------------------------------------------------------------*/
+
+/* USB protocol value = the transport method */
+#define USB_PR_CBI	0x00		// Control/Bulk/Interrupt
+#define USB_PR_CB	0x01		// Control/Bulk w/o interrupt
+#define USB_PR_BULK	0x50		// Bulk-only
+
+/* USB subclass value = the protocol encapsulation */
+#define USB_SC_RBC	0x01		// Reduced Block Commands (flash)
+#define USB_SC_8020	0x02		// SFF-8020i, MMC-2, ATAPI (CD-ROM)
+#define USB_SC_QIC	0x03		// QIC-157 (tape)
+#define USB_SC_UFI	0x04		// UFI (floppy)
+#define USB_SC_8070	0x05		// SFF-8070i (removable)
+#define USB_SC_SCSI	0x06		// Transparent SCSI
+
+/* Bulk-only data structures */
+
+/* Command Block Wrapper */
+struct bulk_cb_wrap {
+	__le32	Signature;		// Contains 'USBC'
+	u32	Tag;			// Unique per command id
+	__le32	DataTransferLength;	// Size of the data
+	u8	Flags;			// Direction in bit 7
+	u8	Lun;			// LUN (normally 0)
+	u8	Length;			// Of the CDB, <= MAX_COMMAND_SIZE
+	u8	CDB[16];		// Command Data Block
+};
+
+#define USB_BULK_CB_WRAP_LEN	31
+#define USB_BULK_CB_SIG		0x43425355	// Spells out USBC
+#define USB_BULK_IN_FLAG	0x80
+
+/* Command Status Wrapper */
+struct bulk_cs_wrap {
+	__le32	Signature;		// Should = 'USBS'
+	u32	Tag;			// Same as original command
+	__le32	Residue;		// Amount not transferred
+	u8	Status;			// See below
+};
+
+#define USB_BULK_CS_WRAP_LEN	13
+#define USB_BULK_CS_SIG		0x53425355	// Spells out 'USBS'
+#define USB_STATUS_PASS		0
+#define USB_STATUS_FAIL		1
+#define USB_STATUS_PHASE_ERROR	2
+
+/* Bulk-only class specific requests */
+#define USB_BULK_RESET_REQUEST		0xff
+#define USB_BULK_GET_MAX_LUN_REQUEST	0xfe
+
+
+/* CBI Interrupt data structure */
+struct interrupt_data {
+	u8	bType;
+	u8	bValue;
+};
+
+#define CBI_INTERRUPT_DATA_LEN		2
+
+/* CBI Accept Device-Specific Command request */
+#define USB_CBI_ADSC_REQUEST		0x00
+
+
+#define MAX_COMMAND_SIZE	16	// Length of a SCSI Command Data Block
+
+/* SCSI commands that we recognize */
+#define SC_FORMAT_UNIT			0x04
+#define SC_INQUIRY			0x12
+#define SC_MODE_SELECT_6		0x15
+#define SC_MODE_SELECT_10		0x55
+#define SC_MODE_SENSE_6			0x1a
+#define SC_MODE_SENSE_10		0x5a
+#define SC_PREVENT_ALLOW_MEDIUM_REMOVAL	0x1e
+#define SC_READ_6			0x08
+#define SC_READ_10			0x28
+#define SC_READ_12			0xa8
+#define SC_READ_CAPACITY		0x25
+#define SC_READ_FORMAT_CAPACITIES	0x23
+#define SC_RELEASE			0x17
+#define SC_REQUEST_SENSE		0x03
+#define SC_RESERVE			0x16
+#define SC_SEND_DIAGNOSTIC		0x1d
+#define SC_START_STOP_UNIT		0x1b
+#define SC_SYNCHRONIZE_CACHE		0x35
+#define SC_TEST_UNIT_READY		0x00
+#define SC_VERIFY			0x2f
+#define SC_WRITE_6			0x0a
+#define SC_WRITE_10			0x2a
+#define SC_WRITE_12			0xaa
+
+/* SCSI Sense Key/Additional Sense Code/ASC Qualifier values */
+#define SS_NO_SENSE				0
+#define SS_COMMUNICATION_FAILURE		0x040800
+#define SS_INVALID_COMMAND			0x052000
+#define SS_INVALID_FIELD_IN_CDB			0x052400
+#define SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE	0x052100
+#define SS_LOGICAL_UNIT_NOT_SUPPORTED		0x052500
+#define SS_MEDIUM_NOT_PRESENT			0x023a00
+#define SS_MEDIUM_REMOVAL_PREVENTED		0x055302
+#define SS_NOT_READY_TO_READY_TRANSITION	0x062800
+#define SS_RESET_OCCURRED			0x062900
+#define SS_SAVING_PARAMETERS_NOT_SUPPORTED	0x053900
+#define SS_UNRECOVERED_READ_ERROR		0x031100
+#define SS_WRITE_ERROR				0x030c02
+#define SS_WRITE_PROTECTED			0x072700
+
+#define SK(x)		((u8) ((x) >> 16))	// Sense Key byte, etc.
+#define ASC(x)		((u8) ((x) >> 8))
+#define ASCQ(x)		((u8) (x))
+
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * These definitions will permit the compiler to avoid generating code for
+ * parts of the driver that aren't used in the non-TEST version.  Even gcc
+ * can recognize when a test of a constant expression yields a dead code
+ * path.
+ */
+
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+
+#define transport_is_bbb()	(mod_data.transport_type == USB_PR_BULK)
+#define transport_is_cbi()	(mod_data.transport_type == USB_PR_CBI)
+#define protocol_is_scsi()	(mod_data.protocol_type == USB_SC_SCSI)
+
+#else
+
+#define transport_is_bbb()	1
+#define transport_is_cbi()	0
+#define protocol_is_scsi()	1
+
+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
+
+
+struct lun {
+	struct file	*filp;
+	loff_t		file_length;
+	loff_t		num_sectors;
+
+	unsigned int	ro : 1;
+	unsigned int	prevent_medium_removal : 1;
+	unsigned int	registered : 1;
+
+	u32		sense_data;
+	u32		sense_data_info;
+	u32		unit_attention_data;
+
+	struct device	dev;
+};
+
+#define backing_file_is_open(curlun)	((curlun)->filp != NULL)
+
+static inline struct lun *dev_to_lun(struct device *dev)
+{
+	return container_of(dev, struct lun, dev);
+}
+
+
+/* Big enough to hold our biggest descriptor */
+#define EP0_BUFSIZE	256
+#define DELAYED_STATUS	(EP0_BUFSIZE + 999)	// An impossibly large value
+
+/* Number of buffers we will use.  2 is enough for double-buffering */
+#define NUM_BUFFERS	2
+
+enum fsg_buffer_state {
+	BUF_STATE_EMPTY = 0,
+	BUF_STATE_FULL,
+	BUF_STATE_BUSY
+};
+
+struct fsg_buffhd {
+	void				*buf;
+	dma_addr_t			dma;
+	volatile enum fsg_buffer_state	state;
+	struct fsg_buffhd		*next;
+
+	/* The NetChip 2280 is faster, and handles some protocol faults
+	 * better, if we don't submit any short bulk-out read requests.
+	 * So we will record the intended request length here. */
+	unsigned int			bulk_out_intended_length;
+
+	struct usb_request		*inreq;
+	volatile int			inreq_busy;
+	struct usb_request		*outreq;
+	volatile int			outreq_busy;
+};
+
+enum fsg_state {
+	FSG_STATE_COMMAND_PHASE = -10,		// This one isn't used anywhere
+	FSG_STATE_DATA_PHASE,
+	FSG_STATE_STATUS_PHASE,
+
+	FSG_STATE_IDLE = 0,
+	FSG_STATE_ABORT_BULK_OUT,
+	FSG_STATE_RESET,
+	FSG_STATE_INTERFACE_CHANGE,
+	FSG_STATE_CONFIG_CHANGE,
+	FSG_STATE_DISCONNECT,
+	FSG_STATE_EXIT,
+	FSG_STATE_TERMINATED
+};
+
+enum data_direction {
+	DATA_DIR_UNKNOWN = 0,
+	DATA_DIR_FROM_HOST,
+	DATA_DIR_TO_HOST,
+	DATA_DIR_NONE
+};
+
+struct fsg_dev {
+	/* lock protects: state, all the req_busy's, and cbbuf_cmnd */
+	spinlock_t		lock;
+	struct usb_gadget	*gadget;
+
+	/* filesem protects: backing files in use */
+	struct rw_semaphore	filesem;
+
+	struct usb_ep		*ep0;		// Handy copy of gadget->ep0
+	struct usb_request	*ep0req;	// For control responses
+	volatile unsigned int	ep0_req_tag;
+	const char		*ep0req_name;
+
+	struct usb_request	*intreq;	// For interrupt responses
+	volatile int		intreq_busy;
+	struct fsg_buffhd	*intr_buffhd;
+
+ 	unsigned int		bulk_out_maxpacket;
+	enum fsg_state		state;		// For exception handling
+	unsigned int		exception_req_tag;
+
+	u8			config, new_config;
+
+	unsigned int		running : 1;
+	unsigned int		bulk_in_enabled : 1;
+	unsigned int		bulk_out_enabled : 1;
+	unsigned int		intr_in_enabled : 1;
+	unsigned int		phase_error : 1;
+	unsigned int		short_packet_received : 1;
+	unsigned int		bad_lun_okay : 1;
+
+	unsigned long		atomic_bitflags;
+#define REGISTERED		0
+#define CLEAR_BULK_HALTS	1
+#define SUSPENDED		2
+
+	struct usb_ep		*bulk_in;
+	struct usb_ep		*bulk_out;
+	struct usb_ep		*intr_in;
+
+	struct fsg_buffhd	*next_buffhd_to_fill;
+	struct fsg_buffhd	*next_buffhd_to_drain;
+	struct fsg_buffhd	buffhds[NUM_BUFFERS];
+
+	wait_queue_head_t	thread_wqh;
+	int			thread_wakeup_needed;
+	struct completion	thread_notifier;
+	int			thread_pid;
+	struct task_struct	*thread_task;
+	sigset_t		thread_signal_mask;
+
+	int			cmnd_size;
+	u8			cmnd[MAX_COMMAND_SIZE];
+	enum data_direction	data_dir;
+	u32			data_size;
+	u32			data_size_from_cmnd;
+	u32			tag;
+	unsigned int		lun;
+	u32			residue;
+	u32			usb_amount_left;
+
+	/* The CB protocol offers no way for a host to know when a command
+	 * has completed.  As a result the next command may arrive early,
+	 * and we will still have to handle it.  For that reason we need
+	 * a buffer to store new commands when using CB (or CBI, which
+	 * does not oblige a host to wait for command completion either). */
+	int			cbbuf_cmnd_size;
+	u8			cbbuf_cmnd[MAX_COMMAND_SIZE];
+
+	unsigned int		nluns;
+	struct lun		*luns;
+	struct lun		*curlun;
+	struct completion	lun_released;
+};
+
+typedef void (*fsg_routine_t)(struct fsg_dev *);
+
+static int inline exception_in_progress(struct fsg_dev *fsg)
+{
+	return (fsg->state > FSG_STATE_IDLE);
+}
+
+/* Make bulk-out requests be divisible by the maxpacket size */
+static void inline set_bulk_out_req_length(struct fsg_dev *fsg,
+		struct fsg_buffhd *bh, unsigned int length)
+{
+	unsigned int	rem;
+
+	bh->bulk_out_intended_length = length;
+	rem = length % fsg->bulk_out_maxpacket;
+	if (rem > 0)
+		length += fsg->bulk_out_maxpacket - rem;
+	bh->outreq->length = length;
+}
+
+static struct fsg_dev			*the_fsg;
+static struct usb_gadget_driver		fsg_driver;
+
+static void	close_backing_file(struct lun *curlun);
+static void	close_all_backing_files(struct fsg_dev *fsg);
+
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef DUMP_MSGS
+
+static void dump_msg(struct fsg_dev *fsg, const char *label,
+		const u8 *buf, unsigned int length)
+{
+	unsigned int	start, num, i;
+	char		line[52], *p;
+
+	if (length >= 512)
+		return;
+	DBG(fsg, "%s, length %u:\n", label, length);
+
+	start = 0;
+	while (length > 0) {
+		num = min(length, 16u);
+		p = line;
+		for (i = 0; i < num; ++i) {
+			if (i == 8)
+				*p++ = ' ';
+			sprintf(p, " %02x", buf[i]);
+			p += 3;
+		}
+		*p = 0;
+		printk(KERN_DEBUG "%6x: %s\n", start, line);
+		buf += num;
+		start += num;
+		length -= num;
+	}
+}
+
+static void inline dump_cdb(struct fsg_dev *fsg)
+{}
+
+#else
+
+static void inline dump_msg(struct fsg_dev *fsg, const char *label,
+		const u8 *buf, unsigned int length)
+{}
+
+static void inline dump_cdb(struct fsg_dev *fsg)
+{
+	int	i;
+	char	cmdbuf[3*MAX_COMMAND_SIZE + 1];
+
+	for (i = 0; i < fsg->cmnd_size; ++i)
+		sprintf(cmdbuf + i*3, " %02x", fsg->cmnd[i]);
+	VDBG(fsg, "SCSI CDB: %s\n", cmdbuf);
+}
+
+#endif /* DUMP_MSGS */
+
+
+static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep)
+{
+	const char	*name;
+
+	if (ep == fsg->bulk_in)
+		name = "bulk-in";
+	else if (ep == fsg->bulk_out)
+		name = "bulk-out";
+	else
+		name = ep->name;
+	DBG(fsg, "%s set halt\n", name);
+	return usb_ep_set_halt(ep);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Routines for unaligned data access */
+
+static u16 inline get_be16(u8 *buf)
+{
+	return ((u16) buf[0] << 8) | ((u16) buf[1]);
+}
+
+static u32 inline get_be32(u8 *buf)
+{
+	return ((u32) buf[0] << 24) | ((u32) buf[1] << 16) |
+			((u32) buf[2] << 8) | ((u32) buf[3]);
+}
+
+static void inline put_be16(u8 *buf, u16 val)
+{
+	buf[0] = val >> 8;
+	buf[1] = val;
+}
+
+static void inline put_be32(u8 *buf, u32 val)
+{
+	buf[0] = val >> 24;
+	buf[1] = val >> 16;
+	buf[2] = val >> 8;
+	buf[3] = val;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * DESCRIPTORS ... most are static, but strings and (full) configuration
+ * descriptors are built on demand.  Also the (static) config and interface
+ * descriptors are adjusted during fsg_bind().
+ */
+#define STRING_MANUFACTURER	1
+#define STRING_PRODUCT		2
+#define STRING_SERIAL		3
+#define STRING_CONFIG		4
+#define STRING_INTERFACE	5
+
+/* There is only one configuration. */
+#define	CONFIG_VALUE		1
+
+static struct usb_device_descriptor
+device_desc = {
+	.bLength =		sizeof device_desc,
+	.bDescriptorType =	USB_DT_DEVICE,
+
+	.bcdUSB =		__constant_cpu_to_le16(0x0200),
+	.bDeviceClass =		USB_CLASS_PER_INTERFACE,
+
+	/* The next three values can be overridden by module parameters */
+	.idVendor =		__constant_cpu_to_le16(DRIVER_VENDOR_ID),
+	.idProduct =		__constant_cpu_to_le16(DRIVER_PRODUCT_ID),
+	.bcdDevice =		__constant_cpu_to_le16(0xffff),
+
+	.iManufacturer =	STRING_MANUFACTURER,
+	.iProduct =		STRING_PRODUCT,
+	.iSerialNumber =	STRING_SERIAL,
+	.bNumConfigurations =	1,
+};
+
+static struct usb_config_descriptor
+config_desc = {
+	.bLength =		sizeof config_desc,
+	.bDescriptorType =	USB_DT_CONFIG,
+
+	/* wTotalLength computed by usb_gadget_config_buf() */
+	.bNumInterfaces =	1,
+	.bConfigurationValue =	CONFIG_VALUE,
+	.iConfiguration =	STRING_CONFIG,
+	.bmAttributes =		USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
+	.bMaxPower =		1,	// self-powered
+};
+
+static struct usb_otg_descriptor
+otg_desc = {
+	.bLength =		sizeof(otg_desc),
+	.bDescriptorType =	USB_DT_OTG,
+
+	.bmAttributes =		USB_OTG_SRP,
+};
+
+/* There is only one interface. */
+
+static struct usb_interface_descriptor
+intf_desc = {
+	.bLength =		sizeof intf_desc,
+	.bDescriptorType =	USB_DT_INTERFACE,
+
+	.bNumEndpoints =	2,		// Adjusted during fsg_bind()
+	.bInterfaceClass =	USB_CLASS_MASS_STORAGE,
+	.bInterfaceSubClass =	USB_SC_SCSI,	// Adjusted during fsg_bind()
+	.bInterfaceProtocol =	USB_PR_BULK,	// Adjusted during fsg_bind()
+	.iInterface =		STRING_INTERFACE,
+};
+
+/* Three full-speed endpoint descriptors: bulk-in, bulk-out,
+ * and interrupt-in. */
+
+static struct usb_endpoint_descriptor
+fs_bulk_in_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	.bEndpointAddress =	USB_DIR_IN,
+	.bmAttributes =		USB_ENDPOINT_XFER_BULK,
+	/* wMaxPacketSize set by autoconfiguration */
+};
+
+static struct usb_endpoint_descriptor
+fs_bulk_out_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	.bEndpointAddress =	USB_DIR_OUT,
+	.bmAttributes =		USB_ENDPOINT_XFER_BULK,
+	/* wMaxPacketSize set by autoconfiguration */
+};
+
+static struct usb_endpoint_descriptor
+fs_intr_in_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	.bEndpointAddress =	USB_DIR_IN,
+	.bmAttributes =		USB_ENDPOINT_XFER_INT,
+	.wMaxPacketSize =	__constant_cpu_to_le16(2),
+	.bInterval =		32,	// frames -> 32 ms
+};
+
+static const struct usb_descriptor_header *fs_function[] = {
+	(struct usb_descriptor_header *) &otg_desc,
+	(struct usb_descriptor_header *) &intf_desc,
+	(struct usb_descriptor_header *) &fs_bulk_in_desc,
+	(struct usb_descriptor_header *) &fs_bulk_out_desc,
+	(struct usb_descriptor_header *) &fs_intr_in_desc,
+	NULL,
+};
+#define FS_FUNCTION_PRE_EP_ENTRIES	2
+
+
+#ifdef	CONFIG_USB_GADGET_DUALSPEED
+
+/*
+ * USB 2.0 devices need to expose both high speed and full speed
+ * descriptors, unless they only run at full speed.
+ *
+ * That means alternate endpoint descriptors (bigger packets)
+ * and a "device qualifier" ... plus more construction options
+ * for the config descriptor.
+ */
+static struct usb_qualifier_descriptor
+dev_qualifier = {
+	.bLength =		sizeof dev_qualifier,
+	.bDescriptorType =	USB_DT_DEVICE_QUALIFIER,
+
+	.bcdUSB =		__constant_cpu_to_le16(0x0200),
+	.bDeviceClass =		USB_CLASS_PER_INTERFACE,
+
+	.bNumConfigurations =	1,
+};
+
+static struct usb_endpoint_descriptor
+hs_bulk_in_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	/* bEndpointAddress copied from fs_bulk_in_desc during fsg_bind() */
+	.bmAttributes =		USB_ENDPOINT_XFER_BULK,
+	.wMaxPacketSize =	__constant_cpu_to_le16(512),
+};
+
+static struct usb_endpoint_descriptor
+hs_bulk_out_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	/* bEndpointAddress copied from fs_bulk_out_desc during fsg_bind() */
+	.bmAttributes =		USB_ENDPOINT_XFER_BULK,
+	.wMaxPacketSize =	__constant_cpu_to_le16(512),
+	.bInterval =		1,	// NAK every 1 uframe
+};
+
+static struct usb_endpoint_descriptor
+hs_intr_in_desc = {
+	.bLength =		USB_DT_ENDPOINT_SIZE,
+	.bDescriptorType =	USB_DT_ENDPOINT,
+
+	/* bEndpointAddress copied from fs_intr_in_desc during fsg_bind() */
+	.bmAttributes =		USB_ENDPOINT_XFER_INT,
+	.wMaxPacketSize =	__constant_cpu_to_le16(2),
+	.bInterval =		9,	// 2**(9-1) = 256 uframes -> 32 ms
+};
+
+static const struct usb_descriptor_header *hs_function[] = {
+	(struct usb_descriptor_header *) &otg_desc,
+	(struct usb_descriptor_header *) &intf_desc,
+	(struct usb_descriptor_header *) &hs_bulk_in_desc,
+	(struct usb_descriptor_header *) &hs_bulk_out_desc,
+	(struct usb_descriptor_header *) &hs_intr_in_desc,
+	NULL,
+};
+#define HS_FUNCTION_PRE_EP_ENTRIES	2
+
+/* Maxpacket and other transfer characteristics vary by speed. */
+#define ep_desc(g,fs,hs)	(((g)->speed==USB_SPEED_HIGH) ? (hs) : (fs))
+
+#else
+
+/* If there's no high speed support, always use the full-speed descriptor. */
+#define ep_desc(g,fs,hs)	fs
+
+#endif	/* !CONFIG_USB_GADGET_DUALSPEED */
+
+
+/* The CBI specification limits the serial string to 12 uppercase hexadecimal
+ * characters. */
+static char				manufacturer[64];
+static char				serial[13];
+
+/* Static strings, in UTF-8 (for simplicity we use only ASCII characters) */
+static struct usb_string		strings[] = {
+	{STRING_MANUFACTURER,	manufacturer},
+	{STRING_PRODUCT,	longname},
+	{STRING_SERIAL,		serial},
+	{STRING_CONFIG,		"Self-powered"},
+	{STRING_INTERFACE,	"Mass Storage"},
+	{}
+};
+
+static struct usb_gadget_strings	stringtab = {
+	.language	= 0x0409,		// en-us
+	.strings	= strings,
+};
+
+
+/*
+ * Config descriptors must agree with the code that sets configurations
+ * and with code managing interfaces and their altsettings.  They must
+ * also handle different speeds and other-speed requests.
+ */
+static int populate_config_buf(struct usb_gadget *gadget,
+		u8 *buf, u8 type, unsigned index)
+{
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+	enum usb_device_speed			speed = gadget->speed;
+#endif
+	int					len;
+	const struct usb_descriptor_header	**function;
+
+	if (index > 0)
+		return -EINVAL;
+
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+	if (type == USB_DT_OTHER_SPEED_CONFIG)
+		speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed;
+	if (speed == USB_SPEED_HIGH)
+		function = hs_function;
+	else
+#endif
+		function = fs_function;
+
+	/* for now, don't advertise srp-only devices */
+	if (!gadget->is_otg)
+		function++;
+
+	len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function);
+	((struct usb_config_descriptor *) buf)->bDescriptorType = type;
+	return len;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* These routines may be called in process context or in_irq */
+
+static void wakeup_thread(struct fsg_dev *fsg)
+{
+	/* Tell the main thread that something has happened */
+	fsg->thread_wakeup_needed = 1;
+	wake_up_all(&fsg->thread_wqh);
+}
+
+
+static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
+{
+	unsigned long		flags;
+	struct task_struct	*thread_task;
+
+	/* Do nothing if a higher-priority exception is already in progress.
+	 * If a lower-or-equal priority exception is in progress, preempt it
+	 * and notify the main thread by sending it a signal. */
+	spin_lock_irqsave(&fsg->lock, flags);
+	if (fsg->state <= new_state) {
+		fsg->exception_req_tag = fsg->ep0_req_tag;
+		fsg->state = new_state;
+		thread_task = fsg->thread_task;
+		if (thread_task)
+			send_sig_info(SIGUSR1, SEND_SIG_FORCED, thread_task);
+	}
+	spin_unlock_irqrestore(&fsg->lock, flags);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* The disconnect callback and ep0 routines.  These always run in_irq,
+ * except that ep0_queue() is called in the main thread to acknowledge
+ * completion of various requests: set config, set interface, and
+ * Bulk-only device reset. */
+
+static void fsg_disconnect(struct usb_gadget *gadget)
+{
+	struct fsg_dev		*fsg = get_gadget_data(gadget);
+
+	DBG(fsg, "disconnect or port reset\n");
+	raise_exception(fsg, FSG_STATE_DISCONNECT);
+}
+
+
+static int ep0_queue(struct fsg_dev *fsg)
+{
+	int	rc;
+
+	rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC);
+	if (rc != 0 && rc != -ESHUTDOWN) {
+
+		/* We can't do much more than wait for a reset */
+		WARN(fsg, "error in submission: %s --> %d\n",
+				fsg->ep0->name, rc);
+	}
+	return rc;
+}
+
+static void ep0_complete(struct usb_ep *ep, struct usb_request *req)
+{
+	struct fsg_dev		*fsg = (struct fsg_dev *) ep->driver_data;
+
+	if (req->actual > 0)
+		dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual);
+	if (req->status || req->actual != req->length)
+		DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
+				req->status, req->actual, req->length);
+	if (req->status == -ECONNRESET)		// Request was cancelled
+		usb_ep_fifo_flush(ep);
+
+	if (req->status == 0 && req->context)
+		((fsg_routine_t) (req->context))(fsg);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Bulk and interrupt endpoint completion handlers.
+ * These always run in_irq. */
+
+static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req)
+{
+	struct fsg_dev		*fsg = (struct fsg_dev *) ep->driver_data;
+	struct fsg_buffhd	*bh = (struct fsg_buffhd *) req->context;
+
+	if (req->status || req->actual != req->length)
+		DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
+				req->status, req->actual, req->length);
+	if (req->status == -ECONNRESET)		// Request was cancelled
+		usb_ep_fifo_flush(ep);
+
+	/* Hold the lock while we update the request and buffer states */
+	spin_lock(&fsg->lock);
+	bh->inreq_busy = 0;
+	bh->state = BUF_STATE_EMPTY;
+	spin_unlock(&fsg->lock);
+	wakeup_thread(fsg);
+}
+
+static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req)
+{
+	struct fsg_dev		*fsg = (struct fsg_dev *) ep->driver_data;
+	struct fsg_buffhd	*bh = (struct fsg_buffhd *) req->context;
+
+	dump_msg(fsg, "bulk-out", req->buf, req->actual);
+	if (req->status || req->actual != bh->bulk_out_intended_length)
+		DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
+				req->status, req->actual,
+				bh->bulk_out_intended_length);
+	if (req->status == -ECONNRESET)		// Request was cancelled
+		usb_ep_fifo_flush(ep);
+
+	/* Hold the lock while we update the request and buffer states */
+	spin_lock(&fsg->lock);
+	bh->outreq_busy = 0;
+	bh->state = BUF_STATE_FULL;
+	spin_unlock(&fsg->lock);
+	wakeup_thread(fsg);
+}
+
+
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
+{
+	struct fsg_dev		*fsg = (struct fsg_dev *) ep->driver_data;
+	struct fsg_buffhd	*bh = (struct fsg_buffhd *) req->context;
+
+	if (req->status || req->actual != req->length)
+		DBG(fsg, "%s --> %d, %u/%u\n", __FUNCTION__,
+				req->status, req->actual, req->length);
+	if (req->status == -ECONNRESET)		// Request was cancelled
+		usb_ep_fifo_flush(ep);
+
+	/* Hold the lock while we update the request and buffer states */
+	spin_lock(&fsg->lock);
+	fsg->intreq_busy = 0;
+	bh->state = BUF_STATE_EMPTY;
+	spin_unlock(&fsg->lock);
+	wakeup_thread(fsg);
+}
+
+#else
+static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
+{}
+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Ep0 class-specific handlers.  These always run in_irq. */
+
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct usb_request	*req = fsg->ep0req;
+	static u8		cbi_reset_cmnd[6] = {
+			SC_SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff};
+
+	/* Error in command transfer? */
+	if (req->status || req->length != req->actual ||
+			req->actual < 6 || req->actual > MAX_COMMAND_SIZE) {
+
+		/* Not all controllers allow a protocol stall after
+		 * receiving control-out data, but we'll try anyway. */
+		fsg_set_halt(fsg, fsg->ep0);
+		return;			// Wait for reset
+	}
+
+	/* Is it the special reset command? */
+	if (req->actual >= sizeof cbi_reset_cmnd &&
+			memcmp(req->buf, cbi_reset_cmnd,
+				sizeof cbi_reset_cmnd) == 0) {
+
+		/* Raise an exception to stop the current operation
+		 * and reinitialize our state. */
+		DBG(fsg, "cbi reset request\n");
+		raise_exception(fsg, FSG_STATE_RESET);
+		return;
+	}
+
+	VDBG(fsg, "CB[I] accept device-specific command\n");
+	spin_lock(&fsg->lock);
+
+	/* Save the command for later */
+	if (fsg->cbbuf_cmnd_size)
+		WARN(fsg, "CB[I] overwriting previous command\n");
+	fsg->cbbuf_cmnd_size = req->actual;
+	memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size);
+
+	spin_unlock(&fsg->lock);
+	wakeup_thread(fsg);
+}
+
+#else
+static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{}
+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
+
+
+static int class_setup_req(struct fsg_dev *fsg,
+		const struct usb_ctrlrequest *ctrl)
+{
+	struct usb_request	*req = fsg->ep0req;
+	int			value = -EOPNOTSUPP;
+	u16			w_index = ctrl->wIndex;
+	u16			w_length = ctrl->wLength;
+
+	if (!fsg->config)
+		return value;
+
+	/* Handle Bulk-only class-specific requests */
+	if (transport_is_bbb()) {
+		switch (ctrl->bRequest) {
+
+		case USB_BULK_RESET_REQUEST:
+			if (ctrl->bRequestType != (USB_DIR_OUT |
+					USB_TYPE_CLASS | USB_RECIP_INTERFACE))
+				break;
+			if (w_index != 0) {
+				value = -EDOM;
+				break;
+			}
+
+			/* Raise an exception to stop the current operation
+			 * and reinitialize our state. */
+			DBG(fsg, "bulk reset request\n");
+			raise_exception(fsg, FSG_STATE_RESET);
+			value = DELAYED_STATUS;
+			break;
+
+		case USB_BULK_GET_MAX_LUN_REQUEST:
+			if (ctrl->bRequestType != (USB_DIR_IN |
+					USB_TYPE_CLASS | USB_RECIP_INTERFACE))
+				break;
+			if (w_index != 0) {
+				value = -EDOM;
+				break;
+			}
+			VDBG(fsg, "get max LUN\n");
+			*(u8 *) req->buf = fsg->nluns - 1;
+			value = min(w_length, (u16) 1);
+			break;
+		}
+	}
+
+	/* Handle CBI class-specific requests */
+	else {
+		switch (ctrl->bRequest) {
+
+		case USB_CBI_ADSC_REQUEST:
+			if (ctrl->bRequestType != (USB_DIR_OUT |
+					USB_TYPE_CLASS | USB_RECIP_INTERFACE))
+				break;
+			if (w_index != 0) {
+				value = -EDOM;
+				break;
+			}
+			if (w_length > MAX_COMMAND_SIZE) {
+				value = -EOVERFLOW;
+				break;
+			}
+			value = w_length;
+			fsg->ep0req->context = received_cbi_adsc;
+			break;
+		}
+	}
+
+	if (value == -EOPNOTSUPP)
+		VDBG(fsg,
+			"unknown class-specific control req "
+			"%02x.%02x v%04x i%04x l%u\n",
+			ctrl->bRequestType, ctrl->bRequest,
+			ctrl->wValue, w_index, w_length);
+	return value;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Ep0 standard request handlers.  These always run in_irq. */
+
+static int standard_setup_req(struct fsg_dev *fsg,
+		const struct usb_ctrlrequest *ctrl)
+{
+	struct usb_request	*req = fsg->ep0req;
+	int			value = -EOPNOTSUPP;
+	u16			w_index = ctrl->wIndex;
+	u16			w_value = ctrl->wValue;
+	u16			w_length = ctrl->wLength;
+
+	/* Usually this just stores reply data in the pre-allocated ep0 buffer,
+	 * but config change events will also reconfigure hardware. */
+	switch (ctrl->bRequest) {
+
+	case USB_REQ_GET_DESCRIPTOR:
+		if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
+				USB_RECIP_DEVICE))
+			break;
+		switch (w_value >> 8) {
+
+		case USB_DT_DEVICE:
+			VDBG(fsg, "get device descriptor\n");
+			value = min(w_length, (u16) sizeof device_desc);
+			memcpy(req->buf, &device_desc, value);
+			break;
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+		case USB_DT_DEVICE_QUALIFIER:
+			VDBG(fsg, "get device qualifier\n");
+			if (!fsg->gadget->is_dualspeed)
+				break;
+			value = min(w_length, (u16) sizeof dev_qualifier);
+			memcpy(req->buf, &dev_qualifier, value);
+			break;
+
+		case USB_DT_OTHER_SPEED_CONFIG:
+			VDBG(fsg, "get other-speed config descriptor\n");
+			if (!fsg->gadget->is_dualspeed)
+				break;
+			goto get_config;
+#endif
+		case USB_DT_CONFIG:
+			VDBG(fsg, "get configuration descriptor\n");
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+		get_config:
+#endif
+			value = populate_config_buf(fsg->gadget,
+					req->buf,
+					w_value >> 8,
+					w_value & 0xff);
+			if (value >= 0)
+				value = min(w_length, (u16) value);
+			break;
+
+		case USB_DT_STRING:
+			VDBG(fsg, "get string descriptor\n");
+
+			/* wIndex == language code */
+			value = usb_gadget_get_string(&stringtab,
+					w_value & 0xff, req->buf);
+			if (value >= 0)
+				value = min(w_length, (u16) value);
+			break;
+		}
+		break;
+
+	/* One config, two speeds */
+	case USB_REQ_SET_CONFIGURATION:
+		if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD |
+				USB_RECIP_DEVICE))
+			break;
+		VDBG(fsg, "set configuration\n");
+		if (w_value == CONFIG_VALUE || w_value == 0) {
+			fsg->new_config = w_value;
+
+			/* Raise an exception to wipe out previous transaction
+			 * state (queued bufs, etc) and set the new config. */
+			raise_exception(fsg, FSG_STATE_CONFIG_CHANGE);
+			value = DELAYED_STATUS;
+		}
+		break;
+	case USB_REQ_GET_CONFIGURATION:
+		if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
+				USB_RECIP_DEVICE))
+			break;
+		VDBG(fsg, "get configuration\n");
+		*(u8 *) req->buf = fsg->config;
+		value = min(w_length, (u16) 1);
+		break;
+
+	case USB_REQ_SET_INTERFACE:
+		if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD |
+				USB_RECIP_INTERFACE))
+			break;
+		if (fsg->config && w_index == 0) {
+
+			/* Raise an exception to wipe out previous transaction
+			 * state (queued bufs, etc) and install the new
+			 * interface altsetting. */
+			raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE);
+			value = DELAYED_STATUS;
+		}
+		break;
+	case USB_REQ_GET_INTERFACE:
+		if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
+				USB_RECIP_INTERFACE))
+			break;
+		if (!fsg->config)
+			break;
+		if (w_index != 0) {
+			value = -EDOM;
+			break;
+		}
+		VDBG(fsg, "get interface\n");
+		*(u8 *) req->buf = 0;
+		value = min(w_length, (u16) 1);
+		break;
+
+	default:
+		VDBG(fsg,
+			"unknown control req %02x.%02x v%04x i%04x l%u\n",
+			ctrl->bRequestType, ctrl->bRequest,
+			w_value, w_index, w_length);
+	}
+
+	return value;
+}
+
+
+static int fsg_setup(struct usb_gadget *gadget,
+		const struct usb_ctrlrequest *ctrl)
+{
+	struct fsg_dev		*fsg = get_gadget_data(gadget);
+	int			rc;
+
+	++fsg->ep0_req_tag;		// Record arrival of a new request
+	fsg->ep0req->context = NULL;
+	fsg->ep0req->length = 0;
+	dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl));
+
+	if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS)
+		rc = class_setup_req(fsg, ctrl);
+	else
+		rc = standard_setup_req(fsg, ctrl);
+
+	/* Respond with data/status or defer until later? */
+	if (rc >= 0 && rc != DELAYED_STATUS) {
+		fsg->ep0req->length = rc;
+		fsg->ep0req->zero = (rc < ctrl->wLength &&
+				(rc % gadget->ep0->maxpacket) == 0);
+		fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
+				"ep0-in" : "ep0-out");
+		rc = ep0_queue(fsg);
+	}
+
+	/* Device either stalls (rc < 0) or reports success */
+	return rc;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* All the following routines run in process context */
+
+
+/* Use this for bulk or interrupt transfers, not ep0 */
+static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep,
+		struct usb_request *req, volatile int *pbusy,
+		volatile enum fsg_buffer_state *state)
+{
+	int	rc;
+
+	if (ep == fsg->bulk_in)
+		dump_msg(fsg, "bulk-in", req->buf, req->length);
+	else if (ep == fsg->intr_in)
+		dump_msg(fsg, "intr-in", req->buf, req->length);
+	*pbusy = 1;
+	*state = BUF_STATE_BUSY;
+	rc = usb_ep_queue(ep, req, GFP_KERNEL);
+	if (rc != 0) {
+		*pbusy = 0;
+		*state = BUF_STATE_EMPTY;
+
+		/* We can't do much more than wait for a reset */
+
+		/* Note: currently the net2280 driver fails zero-length
+		 * submissions if DMA is enabled. */
+		if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP &&
+						req->length == 0))
+			WARN(fsg, "error in submission: %s --> %d\n",
+					ep->name, rc);
+	}
+}
+
+
+static int sleep_thread(struct fsg_dev *fsg)
+{
+	int	rc;
+
+	/* Wait until a signal arrives or we are woken up */
+	rc = wait_event_interruptible(fsg->thread_wqh,
+			fsg->thread_wakeup_needed);
+	fsg->thread_wakeup_needed = 0;
+	if (current->flags & PF_FREEZE)
+		refrigerator(PF_FREEZE);
+	return (rc ? -EINTR : 0);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int do_read(struct fsg_dev *fsg)
+{
+	struct lun		*curlun = fsg->curlun;
+	u32			lba;
+	struct fsg_buffhd	*bh;
+	int			rc;
+	u32			amount_left;
+	loff_t			file_offset, file_offset_tmp;
+	unsigned int		amount;
+	unsigned int		partial_page;
+	ssize_t			nread;
+
+	/* Get the starting Logical Block Address and check that it's
+	 * not too big */
+	if (fsg->cmnd[0] == SC_READ_6)
+		lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
+	else {
+		lba = get_be32(&fsg->cmnd[2]);
+
+		/* We allow DPO (Disable Page Out = don't save data in the
+		 * cache) and FUA (Force Unit Access = don't read from the
+		 * cache), but we don't implement them. */
+		if ((fsg->cmnd[1] & ~0x18) != 0) {
+			curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+			return -EINVAL;
+		}
+	}
+	if (lba >= curlun->num_sectors) {
+		curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+		return -EINVAL;
+	}
+	file_offset = ((loff_t) lba) << 9;
+
+	/* Carry out the file reads */
+	amount_left = fsg->data_size_from_cmnd;
+	if (unlikely(amount_left == 0))
+		return -EIO;		// No default reply
+
+	for (;;) {
+
+		/* Figure out how much we need to read:
+		 * Try to read the remaining amount.
+		 * But don't read more than the buffer size.
+		 * And don't try to read past the end of the file.
+		 * Finally, if we're not at a page boundary, don't read past
+		 *	the next page.
+		 * If this means reading 0 then we were asked to read past
+		 *	the end of file. */
+		amount = min((unsigned int) amount_left, mod_data.buflen);
+		amount = min((loff_t) amount,
+				curlun->file_length - file_offset);
+		partial_page = file_offset & (PAGE_CACHE_SIZE - 1);
+		if (partial_page > 0)
+			amount = min(amount, (unsigned int) PAGE_CACHE_SIZE -
+					partial_page);
+
+		/* Wait for the next buffer to become available */
+		bh = fsg->next_buffhd_to_fill;
+		while (bh->state != BUF_STATE_EMPTY) {
+			if ((rc = sleep_thread(fsg)) != 0)
+				return rc;
+		}
+
+		/* If we were asked to read past the end of file,
+		 * end with an empty buffer. */
+		if (amount == 0) {
+			curlun->sense_data =
+					SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+			curlun->sense_data_info = file_offset >> 9;
+			bh->inreq->length = 0;
+			bh->state = BUF_STATE_FULL;
+			break;
+		}
+
+		/* Perform the read */
+		file_offset_tmp = file_offset;
+		nread = vfs_read(curlun->filp,
+				(char __user *) bh->buf,
+				amount, &file_offset_tmp);
+		VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
+				(unsigned long long) file_offset,
+				(int) nread);
+		if (signal_pending(current))
+			return -EINTR;
+
+		if (nread < 0) {
+			LDBG(curlun, "error in file read: %d\n",
+					(int) nread);
+			nread = 0;
+		} else if (nread < amount) {
+			LDBG(curlun, "partial file read: %d/%u\n",
+					(int) nread, amount);
+			nread -= (nread & 511);	// Round down to a block
+		}
+		file_offset  += nread;
+		amount_left  -= nread;
+		fsg->residue -= nread;
+		bh->inreq->length = nread;
+		bh->state = BUF_STATE_FULL;
+
+		/* If an error occurred, report it and its position */
+		if (nread < amount) {
+			curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
+			curlun->sense_data_info = file_offset >> 9;
+			break;
+		}
+
+		if (amount_left == 0)
+			break;		// No more left to read
+
+		/* Send this buffer and go read some more */
+		bh->inreq->zero = 0;
+		start_transfer(fsg, fsg->bulk_in, bh->inreq,
+				&bh->inreq_busy, &bh->state);
+		fsg->next_buffhd_to_fill = bh->next;
+	}
+
+	return -EIO;		// No default reply
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int do_write(struct fsg_dev *fsg)
+{
+	struct lun		*curlun = fsg->curlun;
+	u32			lba;
+	struct fsg_buffhd	*bh;
+	int			get_some_more;
+	u32			amount_left_to_req, amount_left_to_write;
+	loff_t			usb_offset, file_offset, file_offset_tmp;
+	unsigned int		amount;
+	unsigned int		partial_page;
+	ssize_t			nwritten;
+	int			rc;
+
+	if (curlun->ro) {
+		curlun->sense_data = SS_WRITE_PROTECTED;
+		return -EINVAL;
+	}
+	curlun->filp->f_flags &= ~O_SYNC;	// Default is not to wait
+
+	/* Get the starting Logical Block Address and check that it's
+	 * not too big */
+	if (fsg->cmnd[0] == SC_WRITE_6)
+		lba = (fsg->cmnd[1] << 16) | get_be16(&fsg->cmnd[2]);
+	else {
+		lba = get_be32(&fsg->cmnd[2]);
+
+		/* We allow DPO (Disable Page Out = don't save data in the
+		 * cache) and FUA (Force Unit Access = write directly to the
+		 * medium).  We don't implement DPO; we implement FUA by
+		 * performing synchronous output. */
+		if ((fsg->cmnd[1] & ~0x18) != 0) {
+			curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+			return -EINVAL;
+		}
+		if (fsg->cmnd[1] & 0x08)	// FUA
+			curlun->filp->f_flags |= O_SYNC;
+	}
+	if (lba >= curlun->num_sectors) {
+		curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+		return -EINVAL;
+	}
+
+	/* Carry out the file writes */
+	get_some_more = 1;
+	file_offset = usb_offset = ((loff_t) lba) << 9;
+	amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd;
+
+	while (amount_left_to_write > 0) {
+
+		/* Queue a request for more data from the host */
+		bh = fsg->next_buffhd_to_fill;
+		if (bh->state == BUF_STATE_EMPTY && get_some_more) {
+
+			/* Figure out how much we want to get:
+			 * Try to get the remaining amount.
+			 * But don't get more than the buffer size.
+			 * And don't try to go past the end of the file.
+			 * If we're not at a page boundary,
+			 *	don't go past the next page.
+			 * If this means getting 0, then we were asked
+			 *	to write past the end of file.
+			 * Finally, round down to a block boundary. */
+			amount = min(amount_left_to_req, mod_data.buflen);
+			amount = min((loff_t) amount, curlun->file_length -
+					usb_offset);
+			partial_page = usb_offset & (PAGE_CACHE_SIZE - 1);
+			if (partial_page > 0)
+				amount = min(amount,
+	(unsigned int) PAGE_CACHE_SIZE - partial_page);
+
+			if (amount == 0) {
+				get_some_more = 0;
+				curlun->sense_data =
+					SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+				curlun->sense_data_info = usb_offset >> 9;
+				continue;
+			}
+			amount -= (amount & 511);
+			if (amount == 0) {
+
+				/* Why were we were asked to transfer a
+				 * partial block? */
+				get_some_more = 0;
+				continue;
+			}
+
+			/* Get the next buffer */
+			usb_offset += amount;
+			fsg->usb_amount_left -= amount;
+			amount_left_to_req -= amount;
+			if (amount_left_to_req == 0)
+				get_some_more = 0;
+
+			/* amount is always divisible by 512, hence by
+			 * the bulk-out maxpacket size */
+			bh->outreq->length = bh->bulk_out_intended_length =
+					amount;
+			start_transfer(fsg, fsg->bulk_out, bh->outreq,
+					&bh->outreq_busy, &bh->state);
+			fsg->next_buffhd_to_fill = bh->next;
+			continue;
+		}
+
+		/* Write the received data to the backing file */
+		bh = fsg->next_buffhd_to_drain;
+		if (bh->state == BUF_STATE_EMPTY && !get_some_more)
+			break;			// We stopped early
+		if (bh->state == BUF_STATE_FULL) {
+			fsg->next_buffhd_to_drain = bh->next;
+			bh->state = BUF_STATE_EMPTY;
+
+			/* Did something go wrong with the transfer? */
+			if (bh->outreq->status != 0) {
+				curlun->sense_data = SS_COMMUNICATION_FAILURE;
+				curlun->sense_data_info = file_offset >> 9;
+				break;
+			}
+
+			amount = bh->outreq->actual;
+			if (curlun->file_length - file_offset < amount) {
+				LERROR(curlun,
+	"write %u @ %llu beyond end %llu\n",
+	amount, (unsigned long long) file_offset,
+	(unsigned long long) curlun->file_length);
+				amount = curlun->file_length - file_offset;
+			}
+
+			/* Perform the write */
+			file_offset_tmp = file_offset;
+			nwritten = vfs_write(curlun->filp,
+					(char __user *) bh->buf,
+					amount, &file_offset_tmp);
+			VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
+					(unsigned long long) file_offset,
+					(int) nwritten);
+			if (signal_pending(current))
+				return -EINTR;		// Interrupted!
+
+			if (nwritten < 0) {
+				LDBG(curlun, "error in file write: %d\n",
+						(int) nwritten);
+				nwritten = 0;
+			} else if (nwritten < amount) {
+				LDBG(curlun, "partial file write: %d/%u\n",
+						(int) nwritten, amount);
+				nwritten -= (nwritten & 511);
+						// Round down to a block
+			}
+			file_offset += nwritten;
+			amount_left_to_write -= nwritten;
+			fsg->residue -= nwritten;
+
+			/* If an error occurred, report it and its position */
+			if (nwritten < amount) {
+				curlun->sense_data = SS_WRITE_ERROR;
+				curlun->sense_data_info = file_offset >> 9;
+				break;
+			}
+
+			/* Did the host decide to stop early? */
+			if (bh->outreq->actual != bh->outreq->length) {
+				fsg->short_packet_received = 1;
+				break;
+			}
+			continue;
+		}
+
+		/* Wait for something to happen */
+		if ((rc = sleep_thread(fsg)) != 0)
+			return rc;
+	}
+
+	return -EIO;		// No default reply
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Sync the file data, don't bother with the metadata.
+ * This code was copied from fs/buffer.c:sys_fdatasync(). */
+static int fsync_sub(struct lun *curlun)
+{
+	struct file	*filp = curlun->filp;
+	struct inode	*inode;
+	int		rc, err;
+
+	if (curlun->ro || !filp)
+		return 0;
+	if (!filp->f_op->fsync)
+		return -EINVAL;
+
+	inode = filp->f_dentry->d_inode;
+	down(&inode->i_sem);
+	current->flags |= PF_SYNCWRITE;
+	rc = filemap_fdatawrite(inode->i_mapping);
+	err = filp->f_op->fsync(filp, filp->f_dentry, 1);
+	if (!rc)
+		rc = err;
+	err = filemap_fdatawait(inode->i_mapping);
+	if (!rc)
+		rc = err;
+	current->flags &= ~PF_SYNCWRITE;
+	up(&inode->i_sem);
+	VLDBG(curlun, "fdatasync -> %d\n", rc);
+	return rc;
+}
+
+static void fsync_all(struct fsg_dev *fsg)
+{
+	int	i;
+
+	for (i = 0; i < fsg->nluns; ++i)
+		fsync_sub(&fsg->luns[i]);
+}
+
+static int do_synchronize_cache(struct fsg_dev *fsg)
+{
+	struct lun	*curlun = fsg->curlun;
+	int		rc;
+
+	/* We ignore the requested LBA and write out all file's
+	 * dirty data buffers. */
+	rc = fsync_sub(curlun);
+	if (rc)
+		curlun->sense_data = SS_WRITE_ERROR;
+	return 0;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static void invalidate_sub(struct lun *curlun)
+{
+	struct file	*filp = curlun->filp;
+	struct inode	*inode = filp->f_dentry->d_inode;
+	unsigned long	rc;
+
+	rc = invalidate_inode_pages(inode->i_mapping);
+	VLDBG(curlun, "invalidate_inode_pages -> %ld\n", rc);
+}
+
+static int do_verify(struct fsg_dev *fsg)
+{
+	struct lun		*curlun = fsg->curlun;
+	u32			lba;
+	u32			verification_length;
+	struct fsg_buffhd	*bh = fsg->next_buffhd_to_fill;
+	loff_t			file_offset, file_offset_tmp;
+	u32			amount_left;
+	unsigned int		amount;
+	ssize_t			nread;
+
+	/* Get the starting Logical Block Address and check that it's
+	 * not too big */
+	lba = get_be32(&fsg->cmnd[2]);
+	if (lba >= curlun->num_sectors) {
+		curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+		return -EINVAL;
+	}
+
+	/* We allow DPO (Disable Page Out = don't save data in the
+	 * cache) but we don't implement it. */
+	if ((fsg->cmnd[1] & ~0x10) != 0) {
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	verification_length = get_be16(&fsg->cmnd[7]);
+	if (unlikely(verification_length == 0))
+		return -EIO;		// No default reply
+
+	/* Prepare to carry out the file verify */
+	amount_left = verification_length << 9;
+	file_offset = ((loff_t) lba) << 9;
+
+	/* Write out all the dirty buffers before invalidating them */
+	fsync_sub(curlun);
+	if (signal_pending(current))
+		return -EINTR;
+
+	invalidate_sub(curlun);
+	if (signal_pending(current))
+		return -EINTR;
+
+	/* Just try to read the requested blocks */
+	while (amount_left > 0) {
+
+		/* Figure out how much we need to read:
+		 * Try to read the remaining amount, but not more than
+		 * the buffer size.
+		 * And don't try to read past the end of the file.
+		 * If this means reading 0 then we were asked to read
+		 * past the end of file. */
+		amount = min((unsigned int) amount_left, mod_data.buflen);
+		amount = min((loff_t) amount,
+				curlun->file_length - file_offset);
+		if (amount == 0) {
+			curlun->sense_data =
+					SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
+			curlun->sense_data_info = file_offset >> 9;
+			break;
+		}
+
+		/* Perform the read */
+		file_offset_tmp = file_offset;
+		nread = vfs_read(curlun->filp,
+				(char __user *) bh->buf,
+				amount, &file_offset_tmp);
+		VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
+				(unsigned long long) file_offset,
+				(int) nread);
+		if (signal_pending(current))
+			return -EINTR;
+
+		if (nread < 0) {
+			LDBG(curlun, "error in file verify: %d\n",
+					(int) nread);
+			nread = 0;
+		} else if (nread < amount) {
+			LDBG(curlun, "partial file verify: %d/%u\n",
+					(int) nread, amount);
+			nread -= (nread & 511);	// Round down to a sector
+		}
+		if (nread == 0) {
+			curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
+			curlun->sense_data_info = file_offset >> 9;
+			break;
+		}
+		file_offset += nread;
+		amount_left -= nread;
+	}
+	return 0;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	u8	*buf = (u8 *) bh->buf;
+
+	static char vendor_id[] = "Linux   ";
+	static char product_id[] = "File-Stor Gadget";
+
+	if (!fsg->curlun) {		// Unsupported LUNs are okay
+		fsg->bad_lun_okay = 1;
+		memset(buf, 0, 36);
+		buf[0] = 0x7f;		// Unsupported, no device-type
+		return 36;
+	}
+
+	memset(buf, 0, 8);	// Non-removable, direct-access device
+	if (mod_data.removable)
+		buf[1] = 0x80;
+	buf[2] = 2;		// ANSI SCSI level 2
+	buf[3] = 2;		// SCSI-2 INQUIRY data format
+	buf[4] = 31;		// Additional length
+				// No special options
+	sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, product_id,
+			mod_data.release);
+	return 36;
+}
+
+
+static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct lun	*curlun = fsg->curlun;
+	u8		*buf = (u8 *) bh->buf;
+	u32		sd, sdinfo;
+
+	/*
+	 * From the SCSI-2 spec., section 7.9 (Unit attention condition):
+	 *
+	 * If a REQUEST SENSE command is received from an initiator
+	 * with a pending unit attention condition (before the target
+	 * generates the contingent allegiance condition), then the
+	 * target shall either:
+	 *   a) report any pending sense data and preserve the unit
+	 *	attention condition on the logical unit, or,
+	 *   b) report the unit attention condition, may discard any
+	 *	pending sense data, and clear the unit attention
+	 *	condition on the logical unit for that initiator.
+	 *
+	 * FSG normally uses option a); enable this code to use option b).
+	 */
+#if 0
+	if (curlun && curlun->unit_attention_data != SS_NO_SENSE) {
+		curlun->sense_data = curlun->unit_attention_data;
+		curlun->unit_attention_data = SS_NO_SENSE;
+	}
+#endif
+
+	if (!curlun) {		// Unsupported LUNs are okay
+		fsg->bad_lun_okay = 1;
+		sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
+		sdinfo = 0;
+	} else {
+		sd = curlun->sense_data;
+		sdinfo = curlun->sense_data_info;
+		curlun->sense_data = SS_NO_SENSE;
+		curlun->sense_data_info = 0;
+	}
+
+	memset(buf, 0, 18);
+	buf[0] = 0x80 | 0x70;			// Valid, current error
+	buf[2] = SK(sd);
+	put_be32(&buf[3], sdinfo);		// Sense information
+	buf[7] = 18 - 8;			// Additional sense length
+	buf[12] = ASC(sd);
+	buf[13] = ASCQ(sd);
+	return 18;
+}
+
+
+static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct lun	*curlun = fsg->curlun;
+	u32		lba = get_be32(&fsg->cmnd[2]);
+	int		pmi = fsg->cmnd[8];
+	u8		*buf = (u8 *) bh->buf;
+
+	/* Check the PMI and LBA fields */
+	if (pmi > 1 || (pmi == 0 && lba != 0)) {
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	put_be32(&buf[0], curlun->num_sectors - 1);	// Max logical block
+	put_be32(&buf[4], 512);				// Block length
+	return 8;
+}
+
+
+static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct lun	*curlun = fsg->curlun;
+	int		mscmnd = fsg->cmnd[0];
+	u8		*buf = (u8 *) bh->buf;
+	u8		*buf0 = buf;
+	int		pc, page_code;
+	int		changeable_values, all_pages;
+	int		valid_page = 0;
+	int		len, limit;
+
+	if ((fsg->cmnd[1] & ~0x08) != 0) {		// Mask away DBD
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+	pc = fsg->cmnd[2] >> 6;
+	page_code = fsg->cmnd[2] & 0x3f;
+	if (pc == 3) {
+		curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED;
+		return -EINVAL;
+	}
+	changeable_values = (pc == 1);
+	all_pages = (page_code == 0x3f);
+
+	/* Write the mode parameter header.  Fixed values are: default
+	 * medium type, no cache control (DPOFUA), and no block descriptors.
+	 * The only variable value is the WriteProtect bit.  We will fill in
+	 * the mode data length later. */
+	memset(buf, 0, 8);
+	if (mscmnd == SC_MODE_SENSE_6) {
+		buf[2] = (curlun->ro ? 0x80 : 0x00);		// WP, DPOFUA
+		buf += 4;
+		limit = 255;
+	} else {			// SC_MODE_SENSE_10
+		buf[3] = (curlun->ro ? 0x80 : 0x00);		// WP, DPOFUA
+		buf += 8;
+		limit = 65535;		// Should really be mod_data.buflen
+	}
+
+	/* No block descriptors */
+
+	/* The mode pages, in numerical order.  The only page we support
+	 * is the Caching page. */
+	if (page_code == 0x08 || all_pages) {
+		valid_page = 1;
+		buf[0] = 0x08;		// Page code
+		buf[1] = 10;		// Page length
+		memset(buf+2, 0, 10);	// None of the fields are changeable
+
+		if (!changeable_values) {
+			buf[2] = 0x04;	// Write cache enable,
+					// Read cache not disabled
+					// No cache retention priorities
+			put_be16(&buf[4], 0xffff);  // Don't disable prefetch
+					// Minimum prefetch = 0
+			put_be16(&buf[8], 0xffff);  // Maximum prefetch
+			put_be16(&buf[10], 0xffff); // Maximum prefetch ceiling
+		}
+		buf += 12;
+	}
+
+	/* Check that a valid page was requested and the mode data length
+	 * isn't too long. */
+	len = buf - buf0;
+	if (!valid_page || len > limit) {
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	/*  Store the mode data length */
+	if (mscmnd == SC_MODE_SENSE_6)
+		buf0[0] = len - 1;
+	else
+		put_be16(buf0, len - 2);
+	return len;
+}
+
+
+static int do_start_stop(struct fsg_dev *fsg)
+{
+	struct lun	*curlun = fsg->curlun;
+	int		loej, start;
+
+	if (!mod_data.removable) {
+		curlun->sense_data = SS_INVALID_COMMAND;
+		return -EINVAL;
+	}
+
+	// int immed = fsg->cmnd[1] & 0x01;
+	loej = fsg->cmnd[4] & 0x02;
+	start = fsg->cmnd[4] & 0x01;
+
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+	if ((fsg->cmnd[1] & ~0x01) != 0 ||		// Mask away Immed
+			(fsg->cmnd[4] & ~0x03) != 0) {	// Mask LoEj, Start
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	if (!start) {
+
+		/* Are we allowed to unload the media? */
+		if (curlun->prevent_medium_removal) {
+			LDBG(curlun, "unload attempt prevented\n");
+			curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED;
+			return -EINVAL;
+		}
+		if (loej) {		// Simulate an unload/eject
+			up_read(&fsg->filesem);
+			down_write(&fsg->filesem);
+			close_backing_file(curlun);
+			up_write(&fsg->filesem);
+			down_read(&fsg->filesem);
+		}
+	} else {
+
+		/* Our emulation doesn't support mounting; the medium is
+		 * available for use as soon as it is loaded. */
+		if (!backing_file_is_open(curlun)) {
+			curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
+			return -EINVAL;
+		}
+	}
+#endif
+	return 0;
+}
+
+
+static int do_prevent_allow(struct fsg_dev *fsg)
+{
+	struct lun	*curlun = fsg->curlun;
+	int		prevent;
+
+	if (!mod_data.removable) {
+		curlun->sense_data = SS_INVALID_COMMAND;
+		return -EINVAL;
+	}
+
+	prevent = fsg->cmnd[4] & 0x01;
+	if ((fsg->cmnd[4] & ~0x01) != 0) {		// Mask away Prevent
+		curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+		return -EINVAL;
+	}
+
+	if (curlun->prevent_medium_removal && !prevent)
+		fsync_sub(curlun);
+	curlun->prevent_medium_removal = prevent;
+	return 0;
+}
+
+
+static int do_read_format_capacities(struct fsg_dev *fsg,
+			struct fsg_buffhd *bh)
+{
+	struct lun	*curlun = fsg->curlun;
+	u8		*buf = (u8 *) bh->buf;
+
+	buf[0] = buf[1] = buf[2] = 0;
+	buf[3] = 8;		// Only the Current/Maximum Capacity Descriptor
+	buf += 4;
+
+	put_be32(&buf[0], curlun->num_sectors);		// Number of blocks
+	put_be32(&buf[4], 512);				// Block length
+	buf[4] = 0x02;					// Current capacity
+	return 12;
+}
+
+
+static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct lun	*curlun = fsg->curlun;
+
+	/* We don't support MODE SELECT */
+	curlun->sense_data = SS_INVALID_COMMAND;
+	return -EINVAL;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int halt_bulk_in_endpoint(struct fsg_dev *fsg)
+{
+	int	rc;
+
+	rc = fsg_set_halt(fsg, fsg->bulk_in);
+	if (rc == -EAGAIN)
+		VDBG(fsg, "delayed bulk-in endpoint halt\n");
+	while (rc != 0) {
+		if (rc != -EAGAIN) {
+			WARN(fsg, "usb_ep_set_halt -> %d\n", rc);
+			rc = 0;
+			break;
+		}
+
+		/* Wait for a short time and then try again */
+		if (msleep_interruptible(100) != 0)
+			return -EINTR;
+		rc = usb_ep_set_halt(fsg->bulk_in);
+	}
+	return rc;
+}
+
+static int pad_with_zeros(struct fsg_dev *fsg)
+{
+	struct fsg_buffhd	*bh = fsg->next_buffhd_to_fill;
+	u32			nkeep = bh->inreq->length;
+	u32			nsend;
+	int			rc;
+
+	bh->state = BUF_STATE_EMPTY;		// For the first iteration
+	fsg->usb_amount_left = nkeep + fsg->residue;
+	while (fsg->usb_amount_left > 0) {
+
+		/* Wait for the next buffer to be free */
+		while (bh->state != BUF_STATE_EMPTY) {
+			if ((rc = sleep_thread(fsg)) != 0)
+				return rc;
+		}
+
+		nsend = min(fsg->usb_amount_left, (u32) mod_data.buflen);
+		memset(bh->buf + nkeep, 0, nsend - nkeep);
+		bh->inreq->length = nsend;
+		bh->inreq->zero = 0;
+		start_transfer(fsg, fsg->bulk_in, bh->inreq,
+				&bh->inreq_busy, &bh->state);
+		bh = fsg->next_buffhd_to_fill = bh->next;
+		fsg->usb_amount_left -= nsend;
+		nkeep = 0;
+	}
+	return 0;
+}
+
+static int throw_away_data(struct fsg_dev *fsg)
+{
+	struct fsg_buffhd	*bh;
+	u32			amount;
+	int			rc;
+
+	while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY ||
+			fsg->usb_amount_left > 0) {
+
+		/* Throw away the data in a filled buffer */
+		if (bh->state == BUF_STATE_FULL) {
+			bh->state = BUF_STATE_EMPTY;
+			fsg->next_buffhd_to_drain = bh->next;
+
+			/* A short packet or an error ends everything */
+			if (bh->outreq->actual != bh->outreq->length ||
+					bh->outreq->status != 0) {
+				raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
+				return -EINTR;
+			}
+			continue;
+		}
+
+		/* Try to submit another request if we need one */
+		bh = fsg->next_buffhd_to_fill;
+		if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) {
+			amount = min(fsg->usb_amount_left,
+					(u32) mod_data.buflen);
+
+			/* amount is always divisible by 512, hence by
+			 * the bulk-out maxpacket size */
+			bh->outreq->length = bh->bulk_out_intended_length =
+					amount;
+			start_transfer(fsg, fsg->bulk_out, bh->outreq,
+					&bh->outreq_busy, &bh->state);
+			fsg->next_buffhd_to_fill = bh->next;
+			fsg->usb_amount_left -= amount;
+			continue;
+		}
+
+		/* Otherwise wait for something to happen */
+		if ((rc = sleep_thread(fsg)) != 0)
+			return rc;
+	}
+	return 0;
+}
+
+
+static int finish_reply(struct fsg_dev *fsg)
+{
+	struct fsg_buffhd	*bh = fsg->next_buffhd_to_fill;
+	int			rc = 0;
+
+	switch (fsg->data_dir) {
+	case DATA_DIR_NONE:
+		break;			// Nothing to send
+
+	/* If we don't know whether the host wants to read or write,
+	 * this must be CB or CBI with an unknown command.  We mustn't
+	 * try to send or receive any data.  So stall both bulk pipes
+	 * if we can and wait for a reset. */
+	case DATA_DIR_UNKNOWN:
+		if (mod_data.can_stall) {
+			fsg_set_halt(fsg, fsg->bulk_out);
+			rc = halt_bulk_in_endpoint(fsg);
+		}
+		break;
+
+	/* All but the last buffer of data must have already been sent */
+	case DATA_DIR_TO_HOST:
+		if (fsg->data_size == 0)
+			;		// Nothing to send
+
+		/* If there's no residue, simply send the last buffer */
+		else if (fsg->residue == 0) {
+			bh->inreq->zero = 0;
+			start_transfer(fsg, fsg->bulk_in, bh->inreq,
+					&bh->inreq_busy, &bh->state);
+			fsg->next_buffhd_to_fill = bh->next;
+		}
+
+		/* There is a residue.  For CB and CBI, simply mark the end
+		 * of the data with a short packet.  However, if we are
+		 * allowed to stall, there was no data at all (residue ==
+		 * data_size), and the command failed (invalid LUN or
+		 * sense data is set), then halt the bulk-in endpoint
+		 * instead. */
+		else if (!transport_is_bbb()) {
+			if (mod_data.can_stall &&
+					fsg->residue == fsg->data_size &&
+	(!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) {
+				bh->state = BUF_STATE_EMPTY;
+				rc = halt_bulk_in_endpoint(fsg);
+			} else {
+				bh->inreq->zero = 1;
+				start_transfer(fsg, fsg->bulk_in, bh->inreq,
+						&bh->inreq_busy, &bh->state);
+				fsg->next_buffhd_to_fill = bh->next;
+			}
+		}
+
+		/* For Bulk-only, if we're allowed to stall then send the
+		 * short packet and halt the bulk-in endpoint.  If we can't
+		 * stall, pad out the remaining data with 0's. */
+		else {
+			if (mod_data.can_stall) {
+				bh->inreq->zero = 1;
+				start_transfer(fsg, fsg->bulk_in, bh->inreq,
+						&bh->inreq_busy, &bh->state);
+				fsg->next_buffhd_to_fill = bh->next;
+				rc = halt_bulk_in_endpoint(fsg);
+			} else
+				rc = pad_with_zeros(fsg);
+		}
+		break;
+
+	/* We have processed all we want from the data the host has sent.
+	 * There may still be outstanding bulk-out requests. */
+	case DATA_DIR_FROM_HOST:
+		if (fsg->residue == 0)
+			;		// Nothing to receive
+
+		/* Did the host stop sending unexpectedly early? */
+		else if (fsg->short_packet_received) {
+			raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
+			rc = -EINTR;
+		}
+
+		/* We haven't processed all the incoming data.  Even though
+		 * we may be allowed to stall, doing so would cause a race.
+		 * The controller may already have ACK'ed all the remaining
+		 * bulk-out packets, in which case the host wouldn't see a
+		 * STALL.  Not realizing the endpoint was halted, it wouldn't
+		 * clear the halt -- leading to problems later on. */
+#if 0
+		else if (mod_data.can_stall) {
+			fsg_set_halt(fsg, fsg->bulk_out);
+			raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
+			rc = -EINTR;
+		}
+#endif
+
+		/* We can't stall.  Read in the excess data and throw it
+		 * all away. */
+		else
+			rc = throw_away_data(fsg);
+		break;
+	}
+	return rc;
+}
+
+
+static int send_status(struct fsg_dev *fsg)
+{
+	struct lun		*curlun = fsg->curlun;
+	struct fsg_buffhd	*bh;
+	int			rc;
+	u8			status = USB_STATUS_PASS;
+	u32			sd, sdinfo = 0;
+
+	/* Wait for the next buffer to become available */
+	bh = fsg->next_buffhd_to_fill;
+	while (bh->state != BUF_STATE_EMPTY) {
+		if ((rc = sleep_thread(fsg)) != 0)
+			return rc;
+	}
+
+	if (curlun) {
+		sd = curlun->sense_data;
+		sdinfo = curlun->sense_data_info;
+	} else if (fsg->bad_lun_okay)
+		sd = SS_NO_SENSE;
+	else
+		sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
+
+	if (fsg->phase_error) {
+		DBG(fsg, "sending phase-error status\n");
+		status = USB_STATUS_PHASE_ERROR;
+		sd = SS_INVALID_COMMAND;
+	} else if (sd != SS_NO_SENSE) {
+		DBG(fsg, "sending command-failure status\n");
+		status = USB_STATUS_FAIL;
+		VDBG(fsg, "  sense data: SK x%02x, ASC x%02x, ASCQ x%02x;"
+				"  info x%x\n",
+				SK(sd), ASC(sd), ASCQ(sd), sdinfo);
+	}
+
+	if (transport_is_bbb()) {
+		struct bulk_cs_wrap	*csw = (struct bulk_cs_wrap *) bh->buf;
+
+		/* Store and send the Bulk-only CSW */
+		csw->Signature = __constant_cpu_to_le32(USB_BULK_CS_SIG);
+		csw->Tag = fsg->tag;
+		csw->Residue = cpu_to_le32(fsg->residue);
+		csw->Status = status;
+
+		bh->inreq->length = USB_BULK_CS_WRAP_LEN;
+		bh->inreq->zero = 0;
+		start_transfer(fsg, fsg->bulk_in, bh->inreq,
+				&bh->inreq_busy, &bh->state);
+
+	} else if (mod_data.transport_type == USB_PR_CB) {
+
+		/* Control-Bulk transport has no status phase! */
+		return 0;
+
+	} else {			// USB_PR_CBI
+		struct interrupt_data	*buf = (struct interrupt_data *)
+						bh->buf;
+
+		/* Store and send the Interrupt data.  UFI sends the ASC
+		 * and ASCQ bytes.  Everything else sends a Type (which
+		 * is always 0) and the status Value. */
+		if (mod_data.protocol_type == USB_SC_UFI) {
+			buf->bType = ASC(sd);
+			buf->bValue = ASCQ(sd);
+		} else {
+			buf->bType = 0;
+			buf->bValue = status;
+		}
+		fsg->intreq->length = CBI_INTERRUPT_DATA_LEN;
+
+		fsg->intr_buffhd = bh;		// Point to the right buffhd
+		fsg->intreq->buf = bh->inreq->buf;
+		fsg->intreq->dma = bh->inreq->dma;
+		fsg->intreq->context = bh;
+		start_transfer(fsg, fsg->intr_in, fsg->intreq,
+				&fsg->intreq_busy, &bh->state);
+	}
+
+	fsg->next_buffhd_to_fill = bh->next;
+	return 0;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* Check whether the command is properly formed and whether its data size
+ * and direction agree with the values we already have. */
+static int check_command(struct fsg_dev *fsg, int cmnd_size,
+		enum data_direction data_dir, unsigned int mask,
+		int needs_medium, const char *name)
+{
+	int			i;
+	int			lun = fsg->cmnd[1] >> 5;
+	static const char	dirletter[4] = {'u', 'o', 'i', 'n'};
+	char			hdlen[20];
+	struct lun		*curlun;
+
+	/* Adjust the expected cmnd_size for protocol encapsulation padding.
+	 * Transparent SCSI doesn't pad. */
+	if (protocol_is_scsi())
+		;
+
+	/* There's some disagreement as to whether RBC pads commands or not.
+	 * We'll play it safe and accept either form. */
+	else if (mod_data.protocol_type == USB_SC_RBC) {
+		if (fsg->cmnd_size == 12)
+			cmnd_size = 12;
+
+	/* All the other protocols pad to 12 bytes */
+	} else
+		cmnd_size = 12;
+
+	hdlen[0] = 0;
+	if (fsg->data_dir != DATA_DIR_UNKNOWN)
+		sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir],
+				fsg->data_size);
+	VDBG(fsg, "SCSI command: %s;  Dc=%d, D%c=%u;  Hc=%d%s\n",
+			name, cmnd_size, dirletter[(int) data_dir],
+			fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen);
+
+	/* We can't reply at all until we know the correct data direction
+	 * and size. */
+	if (fsg->data_size_from_cmnd == 0)
+		data_dir = DATA_DIR_NONE;
+	if (fsg->data_dir == DATA_DIR_UNKNOWN) {	// CB or CBI
+		fsg->data_dir = data_dir;
+		fsg->data_size = fsg->data_size_from_cmnd;
+
+	} else {					// Bulk-only
+		if (fsg->data_size < fsg->data_size_from_cmnd) {
+
+			/* Host data size < Device data size is a phase error.
+			 * Carry out the command, but only transfer as much
+			 * as we are allowed. */
+			fsg->data_size_from_cmnd = fsg->data_size;
+			fsg->phase_error = 1;
+		}
+	}
+	fsg->residue = fsg->usb_amount_left = fsg->data_size;
+
+	/* Conflicting data directions is a phase error */
+	if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) {
+		fsg->phase_error = 1;
+		return -EINVAL;
+	}
+
+	/* Verify the length of the command itself */
+	if (cmnd_size != fsg->cmnd_size) {
+
+		/* Special case workaround: MS-Windows issues REQUEST SENSE
+		 * with cbw->Length == 12 (it should be 6). */
+		if (fsg->cmnd[0] == SC_REQUEST_SENSE && fsg->cmnd_size == 12)
+			cmnd_size = fsg->cmnd_size;
+		else {
+			fsg->phase_error = 1;
+			return -EINVAL;
+		}
+	}
+
+	/* Check that the LUN values are oonsistent */
+	if (transport_is_bbb()) {
+		if (fsg->lun != lun)
+			DBG(fsg, "using LUN %d from CBW, "
+					"not LUN %d from CDB\n",
+					fsg->lun, lun);
+	} else
+		fsg->lun = lun;		// Use LUN from the command
+
+	/* Check the LUN */
+	if (fsg->lun >= 0 && fsg->lun < fsg->nluns) {
+		fsg->curlun = curlun = &fsg->luns[fsg->lun];
+		if (fsg->cmnd[0] != SC_REQUEST_SENSE) {
+			curlun->sense_data = SS_NO_SENSE;
+			curlun->sense_data_info = 0;
+		}
+	} else {
+		fsg->curlun = curlun = NULL;
+		fsg->bad_lun_okay = 0;
+
+		/* INQUIRY and REQUEST SENSE commands are explicitly allowed
+		 * to use unsupported LUNs; all others may not. */
+		if (fsg->cmnd[0] != SC_INQUIRY &&
+				fsg->cmnd[0] != SC_REQUEST_SENSE) {
+			DBG(fsg, "unsupported LUN %d\n", fsg->lun);
+			return -EINVAL;
+		}
+	}
+
+	/* If a unit attention condition exists, only INQUIRY and
+	 * REQUEST SENSE commands are allowed; anything else must fail. */
+	if (curlun && curlun->unit_attention_data != SS_NO_SENSE &&
+			fsg->cmnd[0] != SC_INQUIRY &&
+			fsg->cmnd[0] != SC_REQUEST_SENSE) {
+		curlun->sense_data = curlun->unit_attention_data;
+		curlun->unit_attention_data = SS_NO_SENSE;
+		return -EINVAL;
+	}
+
+	/* Check that only command bytes listed in the mask are non-zero */
+	fsg->cmnd[1] &= 0x1f;			// Mask away the LUN
+	for (i = 1; i < cmnd_size; ++i) {
+		if (fsg->cmnd[i] && !(mask & (1 << i))) {
+			if (curlun)
+				curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
+			return -EINVAL;
+		}
+	}
+
+	/* If the medium isn't mounted and the command needs to access
+	 * it, return an error. */
+	if (curlun && !backing_file_is_open(curlun) && needs_medium) {
+		curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+
+static int do_scsi_command(struct fsg_dev *fsg)
+{
+	struct fsg_buffhd	*bh;
+	int			rc;
+	int			reply = -EINVAL;
+	int			i;
+	static char		unknown[16];
+
+	dump_cdb(fsg);
+
+	/* Wait for the next buffer to become available for data or status */
+	bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill;
+	while (bh->state != BUF_STATE_EMPTY) {
+		if ((rc = sleep_thread(fsg)) != 0)
+			return rc;
+		}
+	fsg->phase_error = 0;
+	fsg->short_packet_received = 0;
+
+	down_read(&fsg->filesem);	// We're using the backing file
+	switch (fsg->cmnd[0]) {
+
+	case SC_INQUIRY:
+		fsg->data_size_from_cmnd = fsg->cmnd[4];
+		if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
+				(1<<4), 0,
+				"INQUIRY")) == 0)
+			reply = do_inquiry(fsg, bh);
+		break;
+
+	case SC_MODE_SELECT_6:
+		fsg->data_size_from_cmnd = fsg->cmnd[4];
+		if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
+				(1<<1) | (1<<4), 0,
+				"MODE SELECT(6)")) == 0)
+			reply = do_mode_select(fsg, bh);
+		break;
+
+	case SC_MODE_SELECT_10:
+		fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
+		if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
+				(1<<1) | (3<<7), 0,
+				"MODE SELECT(10)")) == 0)
+			reply = do_mode_select(fsg, bh);
+		break;
+
+	case SC_MODE_SENSE_6:
+		fsg->data_size_from_cmnd = fsg->cmnd[4];
+		if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
+				(1<<1) | (1<<2) | (1<<4), 0,
+				"MODE SENSE(6)")) == 0)
+			reply = do_mode_sense(fsg, bh);
+		break;
+
+	case SC_MODE_SENSE_10:
+		fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
+		if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
+				(1<<1) | (1<<2) | (3<<7), 0,
+				"MODE SENSE(10)")) == 0)
+			reply = do_mode_sense(fsg, bh);
+		break;
+
+	case SC_PREVENT_ALLOW_MEDIUM_REMOVAL:
+		fsg->data_size_from_cmnd = 0;
+		if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
+				(1<<4), 0,
+				"PREVENT-ALLOW MEDIUM REMOVAL")) == 0)
+			reply = do_prevent_allow(fsg);
+		break;
+
+	case SC_READ_6:
+		i = fsg->cmnd[4];
+		fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
+		if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
+				(7<<1) | (1<<4), 1,
+				"READ(6)")) == 0)
+			reply = do_read(fsg);
+		break;
+
+	case SC_READ_10:
+		fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
+		if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
+				(1<<1) | (0xf<<2) | (3<<7), 1,
+				"READ(10)")) == 0)
+			reply = do_read(fsg);
+		break;
+
+	case SC_READ_12:
+		fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
+		if ((reply = check_command(fsg, 12, DATA_DIR_TO_HOST,
+				(1<<1) | (0xf<<2) | (0xf<<6), 1,
+				"READ(12)")) == 0)
+			reply = do_read(fsg);
+		break;
+
+	case SC_READ_CAPACITY:
+		fsg->data_size_from_cmnd = 8;
+		if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
+				(0xf<<2) | (1<<8), 1,
+				"READ CAPACITY")) == 0)
+			reply = do_read_capacity(fsg, bh);
+		break;
+
+	case SC_READ_FORMAT_CAPACITIES:
+		fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]);
+		if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
+				(3<<7), 1,
+				"READ FORMAT CAPACITIES")) == 0)
+			reply = do_read_format_capacities(fsg, bh);
+		break;
+
+	case SC_REQUEST_SENSE:
+		fsg->data_size_from_cmnd = fsg->cmnd[4];
+		if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
+				(1<<4), 0,
+				"REQUEST SENSE")) == 0)
+			reply = do_request_sense(fsg, bh);
+		break;
+
+	case SC_START_STOP_UNIT:
+		fsg->data_size_from_cmnd = 0;
+		if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
+				(1<<1) | (1<<4), 0,
+				"START-STOP UNIT")) == 0)
+			reply = do_start_stop(fsg);
+		break;
+
+	case SC_SYNCHRONIZE_CACHE:
+		fsg->data_size_from_cmnd = 0;
+		if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
+				(0xf<<2) | (3<<7), 1,
+				"SYNCHRONIZE CACHE")) == 0)
+			reply = do_synchronize_cache(fsg);
+		break;
+
+	case SC_TEST_UNIT_READY:
+		fsg->data_size_from_cmnd = 0;
+		reply = check_command(fsg, 6, DATA_DIR_NONE,
+				0, 1,
+				"TEST UNIT READY");
+		break;
+
+	/* Although optional, this command is used by MS-Windows.  We
+	 * support a minimal version: BytChk must be 0. */
+	case SC_VERIFY:
+		fsg->data_size_from_cmnd = 0;
+		if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
+				(1<<1) | (0xf<<2) | (3<<7), 1,
+				"VERIFY")) == 0)
+			reply = do_verify(fsg);
+		break;
+
+	case SC_WRITE_6:
+		i = fsg->cmnd[4];
+		fsg->data_size_from_cmnd = (i == 0 ? 256 : i) << 9;
+		if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
+				(7<<1) | (1<<4), 1,
+				"WRITE(6)")) == 0)
+			reply = do_write(fsg);
+		break;
+
+	case SC_WRITE_10:
+		fsg->data_size_from_cmnd = get_be16(&fsg->cmnd[7]) << 9;
+		if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
+				(1<<1) | (0xf<<2) | (3<<7), 1,
+				"WRITE(10)")) == 0)
+			reply = do_write(fsg);
+		break;
+
+	case SC_WRITE_12:
+		fsg->data_size_from_cmnd = get_be32(&fsg->cmnd[6]) << 9;
+		if ((reply = check_command(fsg, 12, DATA_DIR_FROM_HOST,
+				(1<<1) | (0xf<<2) | (0xf<<6), 1,
+				"WRITE(12)")) == 0)
+			reply = do_write(fsg);
+		break;
+
+	/* Some mandatory commands that we recognize but don't implement.
+	 * They don't mean much in this setting.  It's left as an exercise
+	 * for anyone interested to implement RESERVE and RELEASE in terms
+	 * of Posix locks. */
+	case SC_FORMAT_UNIT:
+	case SC_RELEASE:
+	case SC_RESERVE:
+	case SC_SEND_DIAGNOSTIC:
+		// Fall through
+
+	default:
+		fsg->data_size_from_cmnd = 0;
+		sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]);
+		if ((reply = check_command(fsg, fsg->cmnd_size,
+				DATA_DIR_UNKNOWN, 0xff, 0, unknown)) == 0) {
+			fsg->curlun->sense_data = SS_INVALID_COMMAND;
+			reply = -EINVAL;
+		}
+		break;
+	}
+	up_read(&fsg->filesem);
+
+	if (reply == -EINTR || signal_pending(current))
+		return -EINTR;
+
+	/* Set up the single reply buffer for finish_reply() */
+	if (reply == -EINVAL)
+		reply = 0;		// Error reply length
+	if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) {
+		reply = min((u32) reply, fsg->data_size_from_cmnd);
+		bh->inreq->length = reply;
+		bh->state = BUF_STATE_FULL;
+		fsg->residue -= reply;
+	}				// Otherwise it's already set
+
+	return 0;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh)
+{
+	struct usb_request	*req = bh->outreq;
+	struct bulk_cb_wrap	*cbw = (struct bulk_cb_wrap *) req->buf;
+
+	/* Was this a real packet? */
+	if (req->status)
+		return -EINVAL;
+
+	/* Is the CBW valid? */
+	if (req->actual != USB_BULK_CB_WRAP_LEN ||
+			cbw->Signature != __constant_cpu_to_le32(
+				USB_BULK_CB_SIG)) {
+		DBG(fsg, "invalid CBW: len %u sig 0x%x\n",
+				req->actual,
+				le32_to_cpu(cbw->Signature));
+
+		/* The Bulk-only spec says we MUST stall the bulk pipes!
+		 * If we want to avoid stalls, set a flag so that we will
+		 * clear the endpoint halts at the next reset. */
+		if (!mod_data.can_stall)
+			set_bit(CLEAR_BULK_HALTS, &fsg->atomic_bitflags);
+		fsg_set_halt(fsg, fsg->bulk_out);
+		halt_bulk_in_endpoint(fsg);
+		return -EINVAL;
+	}
+
+	/* Is the CBW meaningful? */
+	if (cbw->Lun >= MAX_LUNS || cbw->Flags & ~USB_BULK_IN_FLAG ||
+			cbw->Length < 6 || cbw->Length > MAX_COMMAND_SIZE) {
+		DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, "
+				"cmdlen %u\n",
+				cbw->Lun, cbw->Flags, cbw->Length);
+
+		/* We can do anything we want here, so let's stall the
+		 * bulk pipes if we are allowed to. */
+		if (mod_data.can_stall) {
+			fsg_set_halt(fsg, fsg->bulk_out);
+			halt_bulk_in_endpoint(fsg);
+		}
+		return -EINVAL;
+	}
+
+	/* Save the command for later */
+	fsg->cmnd_size = cbw->Length;
+	memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size);
+	if (cbw->Flags & USB_BULK_IN_FLAG)
+		fsg->data_dir = DATA_DIR_TO_HOST;
+	else
+		fsg->data_dir = DATA_DIR_FROM_HOST;
+	fsg->data_size = le32_to_cpu(cbw->DataTransferLength);
+	if (fsg->data_size == 0)
+		fsg->data_dir = DATA_DIR_NONE;
+	fsg->lun = cbw->Lun;
+	fsg->tag = cbw->Tag;
+	return 0;
+}
+
+
+static int get_next_command(struct fsg_dev *fsg)
+{
+	struct fsg_buffhd	*bh;
+	int			rc = 0;
+
+	if (transport_is_bbb()) {
+
+		/* Wait for the next buffer to become available */
+		bh = fsg->next_buffhd_to_fill;
+		while (bh->state != BUF_STATE_EMPTY) {
+			if ((rc = sleep_thread(fsg)) != 0)
+				return rc;
+			}
+
+		/* Queue a request to read a Bulk-only CBW */
+		set_bulk_out_req_length(fsg, bh, USB_BULK_CB_WRAP_LEN);
+		start_transfer(fsg, fsg->bulk_out, bh->outreq,
+				&bh->outreq_busy, &bh->state);
+
+		/* We will drain the buffer in software, which means we
+		 * can reuse it for the next filling.  No need to advance
+		 * next_buffhd_to_fill. */
+
+		/* Wait for the CBW to arrive */
+		while (bh->state != BUF_STATE_FULL) {
+			if ((rc = sleep_thread(fsg)) != 0)
+				return rc;
+			}
+		rc = received_cbw(fsg, bh);
+		bh->state = BUF_STATE_EMPTY;
+
+	} else {		// USB_PR_CB or USB_PR_CBI
+
+		/* Wait for the next command to arrive */
+		while (fsg->cbbuf_cmnd_size == 0) {
+			if ((rc = sleep_thread(fsg)) != 0)
+				return rc;
+			}
+
+		/* Is the previous status interrupt request still busy?
+		 * The host is allowed to skip reading the status,
+		 * so we must cancel it. */
+		if (fsg->intreq_busy)
+			usb_ep_dequeue(fsg->intr_in, fsg->intreq);
+
+		/* Copy the command and mark the buffer empty */
+		fsg->data_dir = DATA_DIR_UNKNOWN;
+		spin_lock_irq(&fsg->lock);
+		fsg->cmnd_size = fsg->cbbuf_cmnd_size;
+		memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size);
+		fsg->cbbuf_cmnd_size = 0;
+		spin_unlock_irq(&fsg->lock);
+	}
+	return rc;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
+		const struct usb_endpoint_descriptor *d)
+{
+	int	rc;
+
+	ep->driver_data = fsg;
+	rc = usb_ep_enable(ep, d);
+	if (rc)
+		ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
+	return rc;
+}
+
+static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep,
+		struct usb_request **preq)
+{
+	*preq = usb_ep_alloc_request(ep, GFP_ATOMIC);
+	if (*preq)
+		return 0;
+	ERROR(fsg, "can't allocate request for %s\n", ep->name);
+	return -ENOMEM;
+}
+
+/*
+ * Reset interface setting and re-init endpoint state (toggle etc).
+ * Call with altsetting < 0 to disable the interface.  The only other
+ * available altsetting is 0, which enables the interface.
+ */
+static int do_set_interface(struct fsg_dev *fsg, int altsetting)
+{
+	int	rc = 0;
+	int	i;
+	const struct usb_endpoint_descriptor	*d;
+
+	if (fsg->running)
+		DBG(fsg, "reset interface\n");
+
+reset:
+	/* Deallocate the requests */
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		struct fsg_buffhd *bh = &fsg->buffhds[i];
+
+		if (bh->inreq) {
+			usb_ep_free_request(fsg->bulk_in, bh->inreq);
+			bh->inreq = NULL;
+		}
+		if (bh->outreq) {
+			usb_ep_free_request(fsg->bulk_out, bh->outreq);
+			bh->outreq = NULL;
+		}
+	}
+	if (fsg->intreq) {
+		usb_ep_free_request(fsg->intr_in, fsg->intreq);
+		fsg->intreq = NULL;
+	}
+
+	/* Disable the endpoints */
+	if (fsg->bulk_in_enabled) {
+		usb_ep_disable(fsg->bulk_in);
+		fsg->bulk_in_enabled = 0;
+	}
+	if (fsg->bulk_out_enabled) {
+		usb_ep_disable(fsg->bulk_out);
+		fsg->bulk_out_enabled = 0;
+	}
+	if (fsg->intr_in_enabled) {
+		usb_ep_disable(fsg->intr_in);
+		fsg->intr_in_enabled = 0;
+	}
+
+	fsg->running = 0;
+	if (altsetting < 0 || rc != 0)
+		return rc;
+
+	DBG(fsg, "set interface %d\n", altsetting);
+
+	/* Enable the endpoints */
+	d = ep_desc(fsg->gadget, &fs_bulk_in_desc, &hs_bulk_in_desc);
+	if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0)
+		goto reset;
+	fsg->bulk_in_enabled = 1;
+
+	d = ep_desc(fsg->gadget, &fs_bulk_out_desc, &hs_bulk_out_desc);
+	if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0)
+		goto reset;
+	fsg->bulk_out_enabled = 1;
+	fsg->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize);
+
+	if (transport_is_cbi()) {
+		d = ep_desc(fsg->gadget, &fs_intr_in_desc, &hs_intr_in_desc);
+		if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0)
+			goto reset;
+		fsg->intr_in_enabled = 1;
+	}
+
+	/* Allocate the requests */
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		struct fsg_buffhd	*bh = &fsg->buffhds[i];
+
+		if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
+			goto reset;
+		if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0)
+			goto reset;
+		bh->inreq->buf = bh->outreq->buf = bh->buf;
+		bh->inreq->dma = bh->outreq->dma = bh->dma;
+		bh->inreq->context = bh->outreq->context = bh;
+		bh->inreq->complete = bulk_in_complete;
+		bh->outreq->complete = bulk_out_complete;
+	}
+	if (transport_is_cbi()) {
+		if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0)
+			goto reset;
+		fsg->intreq->complete = intr_in_complete;
+	}
+
+	fsg->running = 1;
+	for (i = 0; i < fsg->nluns; ++i)
+		fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
+	return rc;
+}
+
+
+/*
+ * Change our operational configuration.  This code must agree with the code
+ * that returns config descriptors, and with interface altsetting code.
+ *
+ * It's also responsible for power management interactions.  Some
+ * configurations might not work with our current power sources.
+ * For now we just assume the gadget is always self-powered.
+ */
+static int do_set_config(struct fsg_dev *fsg, u8 new_config)
+{
+	int	rc = 0;
+
+	/* Disable the single interface */
+	if (fsg->config != 0) {
+		DBG(fsg, "reset config\n");
+		fsg->config = 0;
+		rc = do_set_interface(fsg, -1);
+	}
+
+	/* Enable the interface */
+	if (new_config != 0) {
+		fsg->config = new_config;
+		if ((rc = do_set_interface(fsg, 0)) != 0)
+			fsg->config = 0;	// Reset on errors
+		else {
+			char *speed;
+
+			switch (fsg->gadget->speed) {
+			case USB_SPEED_LOW:	speed = "low";	break;
+			case USB_SPEED_FULL:	speed = "full";	break;
+			case USB_SPEED_HIGH:	speed = "high";	break;
+			default: 		speed = "?";	break;
+			}
+			INFO(fsg, "%s speed config #%d\n", speed, fsg->config);
+		}
+	}
+	return rc;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static void handle_exception(struct fsg_dev *fsg)
+{
+	siginfo_t		info;
+	int			sig;
+	int			i;
+	int			num_active;
+	struct fsg_buffhd	*bh;
+	enum fsg_state		old_state;
+	u8			new_config;
+	struct lun		*curlun;
+	unsigned int		exception_req_tag;
+	int			rc;
+
+	/* Clear the existing signals.  Anything but SIGUSR1 is converted
+	 * into a high-priority EXIT exception. */
+	for (;;) {
+		sig = dequeue_signal_lock(current, &fsg->thread_signal_mask,
+				&info);
+		if (!sig)
+			break;
+		if (sig != SIGUSR1) {
+			if (fsg->state < FSG_STATE_EXIT)
+				DBG(fsg, "Main thread exiting on signal\n");
+			raise_exception(fsg, FSG_STATE_EXIT);
+		}
+	}
+
+	/* Cancel all the pending transfers */
+	if (fsg->intreq_busy)
+		usb_ep_dequeue(fsg->intr_in, fsg->intreq);
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		bh = &fsg->buffhds[i];
+		if (bh->inreq_busy)
+			usb_ep_dequeue(fsg->bulk_in, bh->inreq);
+		if (bh->outreq_busy)
+			usb_ep_dequeue(fsg->bulk_out, bh->outreq);
+	}
+
+	/* Wait until everything is idle */
+	for (;;) {
+		num_active = fsg->intreq_busy;
+		for (i = 0; i < NUM_BUFFERS; ++i) {
+			bh = &fsg->buffhds[i];
+			num_active += bh->inreq_busy + bh->outreq_busy;
+		}
+		if (num_active == 0)
+			break;
+		if (sleep_thread(fsg))
+			return;
+	}
+
+	/* Clear out the controller's fifos */
+	if (fsg->bulk_in_enabled)
+		usb_ep_fifo_flush(fsg->bulk_in);
+	if (fsg->bulk_out_enabled)
+		usb_ep_fifo_flush(fsg->bulk_out);
+	if (fsg->intr_in_enabled)
+		usb_ep_fifo_flush(fsg->intr_in);
+
+	/* Reset the I/O buffer states and pointers, the SCSI
+	 * state, and the exception.  Then invoke the handler. */
+	spin_lock_irq(&fsg->lock);
+
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		bh = &fsg->buffhds[i];
+		bh->state = BUF_STATE_EMPTY;
+	}
+	fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain =
+			&fsg->buffhds[0];
+
+	exception_req_tag = fsg->exception_req_tag;
+	new_config = fsg->new_config;
+	old_state = fsg->state;
+
+	if (old_state == FSG_STATE_ABORT_BULK_OUT)
+		fsg->state = FSG_STATE_STATUS_PHASE;
+	else {
+		for (i = 0; i < fsg->nluns; ++i) {
+			curlun = &fsg->luns[i];
+			curlun->prevent_medium_removal = 0;
+			curlun->sense_data = curlun->unit_attention_data =
+					SS_NO_SENSE;
+			curlun->sense_data_info = 0;
+		}
+		fsg->state = FSG_STATE_IDLE;
+	}
+	spin_unlock_irq(&fsg->lock);
+
+	/* Carry out any extra actions required for the exception */
+	switch (old_state) {
+	default:
+		break;
+
+	case FSG_STATE_ABORT_BULK_OUT:
+		send_status(fsg);
+		spin_lock_irq(&fsg->lock);
+		if (fsg->state == FSG_STATE_STATUS_PHASE)
+			fsg->state = FSG_STATE_IDLE;
+		spin_unlock_irq(&fsg->lock);
+		break;
+
+	case FSG_STATE_RESET:
+		/* In case we were forced against our will to halt a
+		 * bulk endpoint, clear the halt now.  (The SuperH UDC
+		 * requires this.) */
+		if (test_and_clear_bit(CLEAR_BULK_HALTS,
+				&fsg->atomic_bitflags)) {
+			usb_ep_clear_halt(fsg->bulk_in);
+			usb_ep_clear_halt(fsg->bulk_out);
+		}
+
+		if (transport_is_bbb()) {
+			if (fsg->ep0_req_tag == exception_req_tag)
+				ep0_queue(fsg);	// Complete the status stage
+
+		} else if (transport_is_cbi())
+			send_status(fsg);	// Status by interrupt pipe
+
+		/* Technically this should go here, but it would only be
+		 * a waste of time.  Ditto for the INTERFACE_CHANGE and
+		 * CONFIG_CHANGE cases. */
+		// for (i = 0; i < fsg->nluns; ++i)
+		//	fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
+		break;
+
+	case FSG_STATE_INTERFACE_CHANGE:
+		rc = do_set_interface(fsg, 0);
+		if (fsg->ep0_req_tag != exception_req_tag)
+			break;
+		if (rc != 0)			// STALL on errors
+			fsg_set_halt(fsg, fsg->ep0);
+		else				// Complete the status stage
+			ep0_queue(fsg);
+		break;
+
+	case FSG_STATE_CONFIG_CHANGE:
+		rc = do_set_config(fsg, new_config);
+		if (fsg->ep0_req_tag != exception_req_tag)
+			break;
+		if (rc != 0)			// STALL on errors
+			fsg_set_halt(fsg, fsg->ep0);
+		else				// Complete the status stage
+			ep0_queue(fsg);
+		break;
+
+	case FSG_STATE_DISCONNECT:
+		fsync_all(fsg);
+		do_set_config(fsg, 0);		// Unconfigured state
+		break;
+
+	case FSG_STATE_EXIT:
+	case FSG_STATE_TERMINATED:
+		do_set_config(fsg, 0);			// Free resources
+		spin_lock_irq(&fsg->lock);
+		fsg->state = FSG_STATE_TERMINATED;	// Stop the thread
+		spin_unlock_irq(&fsg->lock);
+		break;
+	}
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static int fsg_main_thread(void *fsg_)
+{
+	struct fsg_dev		*fsg = (struct fsg_dev *) fsg_;
+
+	fsg->thread_task = current;
+
+	/* Release all our userspace resources */
+	daemonize("file-storage-gadget");
+
+	/* Allow the thread to be killed by a signal, but set the signal mask
+	 * to block everything but INT, TERM, KILL, and USR1. */
+	siginitsetinv(&fsg->thread_signal_mask, sigmask(SIGINT) |
+			sigmask(SIGTERM) | sigmask(SIGKILL) |
+			sigmask(SIGUSR1));
+	sigprocmask(SIG_SETMASK, &fsg->thread_signal_mask, NULL);
+
+	/* Arrange for userspace references to be interpreted as kernel
+	 * pointers.  That way we can pass a kernel pointer to a routine
+	 * that expects a __user pointer and it will work okay. */
+	set_fs(get_ds());
+
+	/* Wait for the gadget registration to finish up */
+	wait_for_completion(&fsg->thread_notifier);
+
+	/* The main loop */
+	while (fsg->state != FSG_STATE_TERMINATED) {
+		if (exception_in_progress(fsg) || signal_pending(current)) {
+			handle_exception(fsg);
+			continue;
+		}
+
+		if (!fsg->running) {
+			sleep_thread(fsg);
+			continue;
+		}
+
+		if (get_next_command(fsg))
+			continue;
+
+		spin_lock_irq(&fsg->lock);
+		if (!exception_in_progress(fsg))
+			fsg->state = FSG_STATE_DATA_PHASE;
+		spin_unlock_irq(&fsg->lock);
+
+		if (do_scsi_command(fsg) || finish_reply(fsg))
+			continue;
+
+		spin_lock_irq(&fsg->lock);
+		if (!exception_in_progress(fsg))
+			fsg->state = FSG_STATE_STATUS_PHASE;
+		spin_unlock_irq(&fsg->lock);
+
+		if (send_status(fsg))
+			continue;
+
+		spin_lock_irq(&fsg->lock);
+		if (!exception_in_progress(fsg))
+			fsg->state = FSG_STATE_IDLE;
+		spin_unlock_irq(&fsg->lock);
+		}
+
+	fsg->thread_task = NULL;
+	flush_signals(current);
+
+	/* In case we are exiting because of a signal, unregister the
+	 * gadget driver and close the backing file. */
+	if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) {
+		usb_gadget_unregister_driver(&fsg_driver);
+		close_all_backing_files(fsg);
+	}
+
+	/* Let the unbind and cleanup routines know the thread has exited */
+	complete_and_exit(&fsg->thread_notifier, 0);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* If the next two routines are called while the gadget is registered,
+ * the caller must own fsg->filesem for writing. */
+
+static int open_backing_file(struct lun *curlun, const char *filename)
+{
+	int				ro;
+	struct file			*filp = NULL;
+	int				rc = -EINVAL;
+	struct inode			*inode = NULL;
+	loff_t				size;
+	loff_t				num_sectors;
+
+	/* R/W if we can, R/O if we must */
+	ro = curlun->ro;
+	if (!ro) {
+		filp = filp_open(filename, O_RDWR | O_LARGEFILE, 0);
+		if (-EROFS == PTR_ERR(filp))
+			ro = 1;
+	}
+	if (ro)
+		filp = filp_open(filename, O_RDONLY | O_LARGEFILE, 0);
+	if (IS_ERR(filp)) {
+		LINFO(curlun, "unable to open backing file: %s\n", filename);
+		return PTR_ERR(filp);
+	}
+
+	if (!(filp->f_mode & FMODE_WRITE))
+		ro = 1;
+
+	if (filp->f_dentry)
+		inode = filp->f_dentry->d_inode;
+	if (inode && S_ISBLK(inode->i_mode)) {
+		if (bdev_read_only(inode->i_bdev))
+			ro = 1;
+	} else if (!inode || !S_ISREG(inode->i_mode)) {
+		LINFO(curlun, "invalid file type: %s\n", filename);
+		goto out;
+	}
+
+	/* If we can't read the file, it's no good.
+	 * If we can't write the file, use it read-only. */
+	if (!filp->f_op || !(filp->f_op->read || filp->f_op->aio_read)) {
+		LINFO(curlun, "file not readable: %s\n", filename);
+		goto out;
+	}
+	if (!(filp->f_op->write || filp->f_op->aio_write))
+		ro = 1;
+
+	size = i_size_read(inode->i_mapping->host);
+	if (size < 0) {
+		LINFO(curlun, "unable to find file size: %s\n", filename);
+		rc = (int) size;
+		goto out;
+	}
+	num_sectors = size >> 9;	// File size in 512-byte sectors
+	if (num_sectors == 0) {
+		LINFO(curlun, "file too small: %s\n", filename);
+		rc = -ETOOSMALL;
+		goto out;
+	}
+
+	get_file(filp);
+	curlun->ro = ro;
+	curlun->filp = filp;
+	curlun->file_length = size;
+	curlun->num_sectors = num_sectors;
+	LDBG(curlun, "open backing file: %s\n", filename);
+	rc = 0;
+
+out:
+	filp_close(filp, current->files);
+	return rc;
+}
+
+
+static void close_backing_file(struct lun *curlun)
+{
+	if (curlun->filp) {
+		LDBG(curlun, "close backing file\n");
+		fput(curlun->filp);
+		curlun->filp = NULL;
+	}
+}
+
+static void close_all_backing_files(struct fsg_dev *fsg)
+{
+	int	i;
+
+	for (i = 0; i < fsg->nluns; ++i)
+		close_backing_file(&fsg->luns[i]);
+}
+
+
+static ssize_t show_ro(struct device *dev, char *buf)
+{
+	struct lun	*curlun = dev_to_lun(dev);
+
+	return sprintf(buf, "%d\n", curlun->ro);
+}
+
+static ssize_t show_file(struct device *dev, char *buf)
+{
+	struct lun	*curlun = dev_to_lun(dev);
+	struct fsg_dev	*fsg = (struct fsg_dev *) dev_get_drvdata(dev);
+	char		*p;
+	ssize_t		rc;
+
+	down_read(&fsg->filesem);
+	if (backing_file_is_open(curlun)) {	// Get the complete pathname
+		p = d_path(curlun->filp->f_dentry, curlun->filp->f_vfsmnt,
+				buf, PAGE_SIZE - 1);
+		if (IS_ERR(p))
+			rc = PTR_ERR(p);
+		else {
+			rc = strlen(p);
+			memmove(buf, p, rc);
+			buf[rc] = '\n';		// Add a newline
+			buf[++rc] = 0;
+		}
+	} else {				// No file, return 0 bytes
+		*buf = 0;
+		rc = 0;
+	}
+	up_read(&fsg->filesem);
+	return rc;
+}
+
+
+static ssize_t store_ro(struct device *dev, const char *buf, size_t count)
+{
+	ssize_t		rc = count;
+	struct lun	*curlun = dev_to_lun(dev);
+	struct fsg_dev	*fsg = (struct fsg_dev *) dev_get_drvdata(dev);
+	int		i;
+
+	if (sscanf(buf, "%d", &i) != 1)
+		return -EINVAL;
+
+	/* Allow the write-enable status to change only while the backing file
+	 * is closed. */
+	down_read(&fsg->filesem);
+	if (backing_file_is_open(curlun)) {
+		LDBG(curlun, "read-only status change prevented\n");
+		rc = -EBUSY;
+	} else {
+		curlun->ro = !!i;
+		LDBG(curlun, "read-only status set to %d\n", curlun->ro);
+	}
+	up_read(&fsg->filesem);
+	return rc;
+}
+
+static ssize_t store_file(struct device *dev, const char *buf, size_t count)
+{
+	struct lun	*curlun = dev_to_lun(dev);
+	struct fsg_dev	*fsg = (struct fsg_dev *) dev_get_drvdata(dev);
+	int		rc = 0;
+
+	if (curlun->prevent_medium_removal && backing_file_is_open(curlun)) {
+		LDBG(curlun, "eject attempt prevented\n");
+		return -EBUSY;				// "Door is locked"
+	}
+
+	/* Remove a trailing newline */
+	if (count > 0 && buf[count-1] == '\n')
+		((char *) buf)[count-1] = 0;		// Ugh!
+
+	/* Eject current medium */
+	down_write(&fsg->filesem);
+	if (backing_file_is_open(curlun)) {
+		close_backing_file(curlun);
+		curlun->unit_attention_data = SS_MEDIUM_NOT_PRESENT;
+	}
+
+	/* Load new medium */
+	if (count > 0 && buf[0]) {
+		rc = open_backing_file(curlun, buf);
+		if (rc == 0)
+			curlun->unit_attention_data =
+					SS_NOT_READY_TO_READY_TRANSITION;
+	}
+	up_write(&fsg->filesem);
+	return (rc < 0 ? rc : count);
+}
+
+
+/* The write permissions and store_xxx pointers are set in fsg_bind() */
+static DEVICE_ATTR(ro, 0444, show_ro, NULL);
+static DEVICE_ATTR(file, 0444, show_file, NULL);
+
+
+/*-------------------------------------------------------------------------*/
+
+static void lun_release(struct device *dev)
+{
+	struct fsg_dev	*fsg = (struct fsg_dev *) dev_get_drvdata(dev);
+
+	complete(&fsg->lun_released);
+}
+
+static void fsg_unbind(struct usb_gadget *gadget)
+{
+	struct fsg_dev		*fsg = get_gadget_data(gadget);
+	int			i;
+	struct lun		*curlun;
+	struct usb_request	*req = fsg->ep0req;
+
+	DBG(fsg, "unbind\n");
+	clear_bit(REGISTERED, &fsg->atomic_bitflags);
+
+	/* Unregister the sysfs attribute files and the LUNs */
+	init_completion(&fsg->lun_released);
+	for (i = 0; i < fsg->nluns; ++i) {
+		curlun = &fsg->luns[i];
+		if (curlun->registered) {
+			device_remove_file(&curlun->dev, &dev_attr_ro);
+			device_remove_file(&curlun->dev, &dev_attr_file);
+			device_unregister(&curlun->dev);
+			wait_for_completion(&fsg->lun_released);
+			curlun->registered = 0;
+		}
+	}
+
+	/* If the thread isn't already dead, tell it to exit now */
+	if (fsg->state != FSG_STATE_TERMINATED) {
+		raise_exception(fsg, FSG_STATE_EXIT);
+		wait_for_completion(&fsg->thread_notifier);
+
+		/* The cleanup routine waits for this completion also */
+		complete(&fsg->thread_notifier);
+	}
+
+	/* Free the data buffers */
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		struct fsg_buffhd	*bh = &fsg->buffhds[i];
+
+		if (bh->buf)
+			usb_ep_free_buffer(fsg->bulk_in, bh->buf, bh->dma,
+					mod_data.buflen);
+	}
+
+	/* Free the request and buffer for endpoint 0 */
+	if (req) {
+		if (req->buf)
+			usb_ep_free_buffer(fsg->ep0, req->buf,
+					req->dma, EP0_BUFSIZE);
+		usb_ep_free_request(fsg->ep0, req);
+	}
+
+	set_gadget_data(gadget, NULL);
+}
+
+
+static int __init check_parameters(struct fsg_dev *fsg)
+{
+	int	prot;
+
+	/* Store the default values */
+	mod_data.transport_type = USB_PR_BULK;
+	mod_data.transport_name = "Bulk-only";
+	mod_data.protocol_type = USB_SC_SCSI;
+	mod_data.protocol_name = "Transparent SCSI";
+
+	if (gadget_is_sh(fsg->gadget))
+		mod_data.can_stall = 0;
+
+	if (mod_data.release == 0xffff) {	// Parameter wasn't set
+		if (gadget_is_net2280(fsg->gadget))
+			mod_data.release = 0x0301;
+		else if (gadget_is_dummy(fsg->gadget))
+			mod_data.release = 0x0302;
+		else if (gadget_is_pxa(fsg->gadget))
+			mod_data.release = 0x0303;
+		else if (gadget_is_sh(fsg->gadget))
+			mod_data.release = 0x0304;
+
+		/* The sa1100 controller is not supported */
+
+		else if (gadget_is_goku(fsg->gadget))
+			mod_data.release = 0x0306;
+		else if (gadget_is_mq11xx(fsg->gadget))
+			mod_data.release = 0x0307;
+		else if (gadget_is_omap(fsg->gadget))
+			mod_data.release = 0x0308;
+		else if (gadget_is_lh7a40x(fsg->gadget))
+			mod_data.release = 0x0309;
+		else if (gadget_is_n9604(fsg->gadget))
+			mod_data.release = 0x0310;
+		else if (gadget_is_pxa27x(fsg->gadget))
+			mod_data.release = 0x0311;
+		else if (gadget_is_s3c2410(gadget))
+			mod_data.release = 0x0312;
+		else if (gadget_is_at91(fsg->gadget))
+			mod_data.release = 0x0313;
+		else {
+			WARN(fsg, "controller '%s' not recognized\n",
+				fsg->gadget->name);
+			mod_data.release = 0x0399;
+		}
+	}
+
+	prot = simple_strtol(mod_data.protocol_parm, NULL, 0);
+
+#ifdef CONFIG_USB_FILE_STORAGE_TEST
+	if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) {
+		;		// Use default setting
+	} else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) {
+		mod_data.transport_type = USB_PR_CB;
+		mod_data.transport_name = "Control-Bulk";
+	} else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) {
+		mod_data.transport_type = USB_PR_CBI;
+		mod_data.transport_name = "Control-Bulk-Interrupt";
+	} else {
+		ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm);
+		return -EINVAL;
+	}
+
+	if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 ||
+			prot == USB_SC_SCSI) {
+		;		// Use default setting
+	} else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 ||
+			prot == USB_SC_RBC) {
+		mod_data.protocol_type = USB_SC_RBC;
+		mod_data.protocol_name = "RBC";
+	} else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 ||
+			strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 ||
+			prot == USB_SC_8020) {
+		mod_data.protocol_type = USB_SC_8020;
+		mod_data.protocol_name = "8020i (ATAPI)";
+	} else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 ||
+			prot == USB_SC_QIC) {
+		mod_data.protocol_type = USB_SC_QIC;
+		mod_data.protocol_name = "QIC-157";
+	} else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 ||
+			prot == USB_SC_UFI) {
+		mod_data.protocol_type = USB_SC_UFI;
+		mod_data.protocol_name = "UFI";
+	} else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 ||
+			prot == USB_SC_8070) {
+		mod_data.protocol_type = USB_SC_8070;
+		mod_data.protocol_name = "8070i";
+	} else {
+		ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm);
+		return -EINVAL;
+	}
+
+	mod_data.buflen &= PAGE_CACHE_MASK;
+	if (mod_data.buflen <= 0) {
+		ERROR(fsg, "invalid buflen\n");
+		return -ETOOSMALL;
+	}
+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
+
+	return 0;
+}
+
+
+static int __init fsg_bind(struct usb_gadget *gadget)
+{
+	struct fsg_dev		*fsg = the_fsg;
+	int			rc;
+	int			i;
+	struct lun		*curlun;
+	struct usb_ep		*ep;
+	struct usb_request	*req;
+	char			*pathbuf, *p;
+
+	fsg->gadget = gadget;
+	set_gadget_data(gadget, fsg);
+	fsg->ep0 = gadget->ep0;
+	fsg->ep0->driver_data = fsg;
+
+	if ((rc = check_parameters(fsg)) != 0)
+		goto out;
+
+	if (mod_data.removable) {	// Enable the store_xxx attributes
+		dev_attr_ro.attr.mode = dev_attr_file.attr.mode = 0644;
+		dev_attr_ro.store = store_ro;
+		dev_attr_file.store = store_file;
+	}
+
+	/* Find out how many LUNs there should be */
+	i = mod_data.nluns;
+	if (i == 0)
+		i = max(mod_data.num_filenames, 1);
+	if (i > MAX_LUNS) {
+		ERROR(fsg, "invalid number of LUNs: %d\n", i);
+		rc = -EINVAL;
+		goto out;
+	}
+
+	/* Create the LUNs, open their backing files, and register the
+	 * LUN devices in sysfs. */
+	fsg->luns = kmalloc(i * sizeof(struct lun), GFP_KERNEL);
+	if (!fsg->luns) {
+		rc = -ENOMEM;
+		goto out;
+	}
+	memset(fsg->luns, 0, i * sizeof(struct lun));
+	fsg->nluns = i;
+
+	for (i = 0; i < fsg->nluns; ++i) {
+		curlun = &fsg->luns[i];
+		curlun->ro = ro[i];
+		curlun->dev.parent = &gadget->dev;
+		curlun->dev.driver = &fsg_driver.driver;
+		dev_set_drvdata(&curlun->dev, fsg);
+		snprintf(curlun->dev.bus_id, BUS_ID_SIZE,
+				"%s-lun%d", gadget->dev.bus_id, i);
+
+		if ((rc = device_register(&curlun->dev)) != 0)
+			INFO(fsg, "failed to register LUN%d: %d\n", i, rc);
+		else {
+			curlun->registered = 1;
+			curlun->dev.release = lun_release;
+			device_create_file(&curlun->dev, &dev_attr_ro);
+			device_create_file(&curlun->dev, &dev_attr_file);
+		}
+
+		if (file[i] && *file[i]) {
+			if ((rc = open_backing_file(curlun, file[i])) != 0)
+				goto out;
+		} else if (!mod_data.removable) {
+			ERROR(fsg, "no file given for LUN%d\n", i);
+			rc = -EINVAL;
+			goto out;
+		}
+	}
+
+	/* Find all the endpoints we will use */
+	usb_ep_autoconfig_reset(gadget);
+	ep = usb_ep_autoconfig(gadget, &fs_bulk_in_desc);
+	if (!ep)
+		goto autoconf_fail;
+	ep->driver_data = fsg;		// claim the endpoint
+	fsg->bulk_in = ep;
+
+	ep = usb_ep_autoconfig(gadget, &fs_bulk_out_desc);
+	if (!ep)
+		goto autoconf_fail;
+	ep->driver_data = fsg;		// claim the endpoint
+	fsg->bulk_out = ep;
+
+	if (transport_is_cbi()) {
+		ep = usb_ep_autoconfig(gadget, &fs_intr_in_desc);
+		if (!ep)
+			goto autoconf_fail;
+		ep->driver_data = fsg;		// claim the endpoint
+		fsg->intr_in = ep;
+	}
+
+	/* Fix up the descriptors */
+	device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket;
+	device_desc.idVendor = cpu_to_le16(mod_data.vendor);
+	device_desc.idProduct = cpu_to_le16(mod_data.product);
+	device_desc.bcdDevice = cpu_to_le16(mod_data.release);
+
+	i = (transport_is_cbi() ? 3 : 2);	// Number of endpoints
+	intf_desc.bNumEndpoints = i;
+	intf_desc.bInterfaceSubClass = mod_data.protocol_type;
+	intf_desc.bInterfaceProtocol = mod_data.transport_type;
+	fs_function[i + FS_FUNCTION_PRE_EP_ENTRIES] = NULL;
+
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+	hs_function[i + HS_FUNCTION_PRE_EP_ENTRIES] = NULL;
+
+	/* Assume ep0 uses the same maxpacket value for both speeds */
+	dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket;
+
+	/* Assume that all endpoint addresses are the same for both speeds */
+	hs_bulk_in_desc.bEndpointAddress = fs_bulk_in_desc.bEndpointAddress;
+	hs_bulk_out_desc.bEndpointAddress = fs_bulk_out_desc.bEndpointAddress;
+	hs_intr_in_desc.bEndpointAddress = fs_intr_in_desc.bEndpointAddress;
+#endif
+
+	if (gadget->is_otg) {
+		otg_desc.bmAttributes |= USB_OTG_HNP,
+		config_desc.bmAttributes |= USB_CONFIG_ATT_WAKEUP;
+	}
+
+	rc = -ENOMEM;
+
+	/* Allocate the request and buffer for endpoint 0 */
+	fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL);
+	if (!req)
+		goto out;
+	req->buf = usb_ep_alloc_buffer(fsg->ep0, EP0_BUFSIZE,
+			&req->dma, GFP_KERNEL);
+	if (!req->buf)
+		goto out;
+	req->complete = ep0_complete;
+
+	/* Allocate the data buffers */
+	for (i = 0; i < NUM_BUFFERS; ++i) {
+		struct fsg_buffhd	*bh = &fsg->buffhds[i];
+
+		bh->buf = usb_ep_alloc_buffer(fsg->bulk_in, mod_data.buflen,
+				&bh->dma, GFP_KERNEL);
+		if (!bh->buf)
+			goto out;
+		bh->next = bh + 1;
+	}
+	fsg->buffhds[NUM_BUFFERS - 1].next = &fsg->buffhds[0];
+
+	/* This should reflect the actual gadget power source */
+	usb_gadget_set_selfpowered(gadget);
+
+	snprintf(manufacturer, sizeof manufacturer, "%s %s with %s",
+			system_utsname.sysname, system_utsname.release,
+			gadget->name);
+
+	/* On a real device, serial[] would be loaded from permanent
+	 * storage.  We just encode it from the driver version string. */
+	for (i = 0; i < sizeof(serial) - 2; i += 2) {
+		unsigned char		c = DRIVER_VERSION[i / 2];
+
+		if (!c)
+			break;
+		sprintf(&serial[i], "%02X", c);
+	}
+
+	if ((rc = kernel_thread(fsg_main_thread, fsg, (CLONE_VM | CLONE_FS |
+			CLONE_FILES))) < 0)
+		goto out;
+	fsg->thread_pid = rc;
+
+	INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
+	INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
+
+	pathbuf = kmalloc(PATH_MAX, GFP_KERNEL);
+	for (i = 0; i < fsg->nluns; ++i) {
+		curlun = &fsg->luns[i];
+		if (backing_file_is_open(curlun)) {
+			p = NULL;
+			if (pathbuf) {
+				p = d_path(curlun->filp->f_dentry,
+					curlun->filp->f_vfsmnt,
+					pathbuf, PATH_MAX);
+				if (IS_ERR(p))
+					p = NULL;
+			}
+			LINFO(curlun, "ro=%d, file: %s\n",
+					curlun->ro, (p ? p : "(error)"));
+		}
+	}
+	kfree(pathbuf);
+
+	DBG(fsg, "transport=%s (x%02x)\n",
+			mod_data.transport_name, mod_data.transport_type);
+	DBG(fsg, "protocol=%s (x%02x)\n",
+			mod_data.protocol_name, mod_data.protocol_type);
+	DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n",
+			mod_data.vendor, mod_data.product, mod_data.release);
+	DBG(fsg, "removable=%d, stall=%d, buflen=%u\n",
+			mod_data.removable, mod_data.can_stall,
+			mod_data.buflen);
+	DBG(fsg, "I/O thread pid: %d\n", fsg->thread_pid);
+	return 0;
+
+autoconf_fail:
+	ERROR(fsg, "unable to autoconfigure all endpoints\n");
+	rc = -ENOTSUPP;
+
+out:
+	fsg->state = FSG_STATE_TERMINATED;	// The thread is dead
+	fsg_unbind(gadget);
+	close_all_backing_files(fsg);
+	return rc;
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static void fsg_suspend(struct usb_gadget *gadget)
+{
+	struct fsg_dev		*fsg = get_gadget_data(gadget);
+
+	DBG(fsg, "suspend\n");
+	set_bit(SUSPENDED, &fsg->atomic_bitflags);
+}
+
+static void fsg_resume(struct usb_gadget *gadget)
+{
+	struct fsg_dev		*fsg = get_gadget_data(gadget);
+
+	DBG(fsg, "resume\n");
+	clear_bit(SUSPENDED, &fsg->atomic_bitflags);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+static struct usb_gadget_driver		fsg_driver = {
+#ifdef CONFIG_USB_GADGET_DUALSPEED
+	.speed		= USB_SPEED_HIGH,
+#else
+	.speed		= USB_SPEED_FULL,
+#endif
+	.function	= (char *) longname,
+	.bind		= fsg_bind,
+	.unbind		= fsg_unbind,
+	.disconnect	= fsg_disconnect,
+	.setup		= fsg_setup,
+	.suspend	= fsg_suspend,
+	.resume		= fsg_resume,
+
+	.driver		= {
+		.name		= (char *) shortname,
+		// .release = ...
+		// .suspend = ...
+		// .resume = ...
+	},
+};
+
+
+static int __init fsg_alloc(void)
+{
+	struct fsg_dev		*fsg;
+
+	fsg = kmalloc(sizeof *fsg, GFP_KERNEL);
+	if (!fsg)
+		return -ENOMEM;
+	memset(fsg, 0, sizeof *fsg);
+	spin_lock_init(&fsg->lock);
+	init_rwsem(&fsg->filesem);
+	init_waitqueue_head(&fsg->thread_wqh);
+	init_completion(&fsg->thread_notifier);
+
+	the_fsg = fsg;
+	return 0;
+}
+
+
+static void fsg_free(struct fsg_dev *fsg)
+{
+	kfree(fsg->luns);
+	kfree(fsg);
+}
+
+
+static int __init fsg_init(void)
+{
+	int		rc;
+	struct fsg_dev	*fsg;
+
+	if ((rc = fsg_alloc()) != 0)
+		return rc;
+	fsg = the_fsg;
+	if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0) {
+		fsg_free(fsg);
+		return rc;
+	}
+	set_bit(REGISTERED, &fsg->atomic_bitflags);
+
+	/* Tell the thread to start working */
+	complete(&fsg->thread_notifier);
+	return 0;
+}
+module_init(fsg_init);
+
+
+static void __exit fsg_cleanup(void)
+{
+	struct fsg_dev	*fsg = the_fsg;
+
+	/* Unregister the driver iff the thread hasn't already done so */
+	if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
+		usb_gadget_unregister_driver(&fsg_driver);
+
+	/* Wait for the thread to finish up */
+	wait_for_completion(&fsg->thread_notifier);
+
+	close_all_backing_files(fsg);
+	fsg_free(fsg);
+}
+module_exit(fsg_cleanup);