Merge branch 'linus' into idle-test

24 files changed, 2060 insertions, 107 deletions

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 6f4f8e6a40c..24046c0f587 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -133,6 +133,25 @@ config USB_EHCI_MXC
 	---help---
 	  Variation of ARC USB block used in some Freescale chips.
 
+config USB_EHCI_HCD_OMAP
+	bool "EHCI support for OMAP3 and later chips"
+	depends on USB_EHCI_HCD && ARCH_OMAP
+	default y
+	--- help ---
+	  Enables support for the on-chip EHCI controller on
+	  OMAP3 and later chips.
+
+config USB_EHCI_MSM
+	bool "Support for MSM on-chip EHCI USB controller"
+	depends on USB_EHCI_HCD && ARCH_MSM
+	select USB_EHCI_ROOT_HUB_TT
+	select USB_MSM_OTG_72K
+	---help---
+	  Enables support for the USB Host controller present on the
+	  Qualcomm chipsets. Root Hub has inbuilt TT.
+	  This driver depends on OTG driver for PHY initialization,
+	  clock management, powering up VBUS, and power management.
+
 config USB_EHCI_HCD_PPC_OF
 	bool "EHCI support for PPC USB controller on OF platform bus"
 	depends on USB_EHCI_HCD && PPC_OF
@@ -147,6 +166,14 @@ config USB_W90X900_EHCI
 	---help---
 		Enables support for the W90X900 USB controller
 
+config USB_CNS3XXX_EHCI
+	bool "Cavium CNS3XXX EHCI Module"
+	depends on USB_EHCI_HCD && ARCH_CNS3XXX
+	---help---
+	  Enable support for the CNS3XXX SOC's on-chip EHCI controller.
+	  It is needed for high-speed (480Mbit/sec) USB 2.0 device
+	  support.
+
 config USB_OXU210HP_HCD
 	tristate "OXU210HP HCD support"
 	depends on USB
@@ -286,6 +313,13 @@ config USB_OHCI_HCD_SSB
 
 	  If unsure, say N.
 
+config USB_CNS3XXX_OHCI
+	bool "Cavium CNS3XXX OHCI Module"
+	depends on USB_OHCI_HCD && ARCH_CNS3XXX
+	---help---
+	  Enable support for the CNS3XXX SOC's on-chip OHCI controller.
+	  It is needed for low-speed USB 1.0 device support.
+
 config USB_OHCI_BIG_ENDIAN_DESC
 	bool
 	depends on USB_OHCI_HCD
diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c
index 51bd0edf544..d6a69d514a8 100644
--- a/drivers/usb/host/ehci-atmel.c
+++ b/drivers/usb/host/ehci-atmel.c
@@ -99,6 +99,7 @@ static const struct hc_driver ehci_atmel_hc_driver = {
 	.urb_enqueue		= ehci_urb_enqueue,
 	.urb_dequeue		= ehci_urb_dequeue,
 	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
 
 	/* scheduling support */
 	.get_frame_number	= ehci_get_frame,
@@ -110,6 +111,8 @@ static const struct hc_driver ehci_atmel_hc_driver = {
 	.bus_resume		= ehci_bus_resume,
 	.relinquish_port	= ehci_relinquish_port,
 	.port_handed_over	= ehci_port_handed_over,
+
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
 };
 
 static int __init ehci_atmel_drv_probe(struct platform_device *pdev)
diff --git a/drivers/usb/host/ehci-cns3xxx.c b/drivers/usb/host/ehci-cns3xxx.c
new file mode 100644
index 00000000000..708a05b5d25
--- /dev/null
+++ b/drivers/usb/host/ehci-cns3xxx.c
@@ -0,0 +1,171 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/atomic.h>
+#include <mach/cns3xxx.h>
+#include <mach/pm.h>
+
+static int cns3xxx_ehci_init(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int retval;
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 *
+	 * Set USB AHB INCR length to 16
+	 */
+	if (atomic_inc_return(&usb_pwr_ref) == 1) {
+		cns3xxx_pwr_power_up(1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB);
+		cns3xxx_pwr_clk_en(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+		cns3xxx_pwr_soft_rst(1 << PM_SOFT_RST_REG_OFFST_USB_HOST);
+		__raw_writel((__raw_readl(MISC_CHIP_CONFIG_REG) | (0X2 << 24)),
+			MISC_CHIP_CONFIG_REG);
+	}
+
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs
+		+ HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+
+	hcd->has_tt = 0;
+	ehci_reset(ehci);
+
+	retval = ehci_init(hcd);
+	if (retval)
+		return retval;
+
+	ehci_port_power(ehci, 0);
+
+	return retval;
+}
+
+static const struct hc_driver cns3xxx_ehci_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "CNS3XXX EHCI Host Controller",
+	.hcd_priv_size		= sizeof(struct ehci_hcd),
+	.irq			= ehci_irq,
+	.flags			= HCD_MEMORY | HCD_USB2,
+	.reset			= cns3xxx_ehci_init,
+	.start			= ehci_run,
+	.stop			= ehci_stop,
+	.shutdown		= ehci_shutdown,
+	.urb_enqueue		= ehci_urb_enqueue,
+	.urb_dequeue		= ehci_urb_dequeue,
+	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
+	.get_frame_number	= ehci_get_frame,
+	.hub_status_data	= ehci_hub_status_data,
+	.hub_control		= ehci_hub_control,
+#ifdef CONFIG_PM
+	.bus_suspend		= ehci_bus_suspend,
+	.bus_resume		= ehci_bus_resume,
+#endif
+	.relinquish_port	= ehci_relinquish_port,
+	.port_handed_over	= ehci_port_handed_over,
+
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
+};
+
+static int cns3xxx_ehci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct usb_hcd *hcd;
+	const struct hc_driver *driver = &cns3xxx_ehci_hc_driver;
+	struct resource *res;
+	int irq;
+	int retval;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no IRQ.\n");
+		return -ENODEV;
+	}
+	irq = res->start;
+
+	hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
+	if (!hcd)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no register addr.\n");
+		retval = -ENODEV;
+		goto err1;
+	}
+
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = res->end - res->start + 1;
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+				driver->description)) {
+		dev_dbg(dev, "controller already in use\n");
+		retval = -EBUSY;
+		goto err1;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (hcd->regs == NULL) {
+		dev_dbg(dev, "error mapping memory\n");
+		retval = -EFAULT;
+		goto err2;
+	}
+
+	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (retval == 0)
+		return retval;
+
+	iounmap(hcd->regs);
+err2:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+	usb_put_hcd(hcd);
+
+	return retval;
+}
+
+static int cns3xxx_ehci_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 */
+	if (atomic_dec_return(&usb_pwr_ref) == 0)
+		cns3xxx_pwr_clk_dis(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+
+	usb_put_hcd(hcd);
+
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+MODULE_ALIAS("platform:cns3xxx-ehci");
+
+static struct platform_driver cns3xxx_ehci_driver = {
+	.probe = cns3xxx_ehci_probe,
+	.remove = cns3xxx_ehci_remove,
+	.driver = {
+		.name = "cns3xxx-ehci",
+	},
+};
diff --git a/drivers/usb/host/ehci-dbg.c b/drivers/usb/host/ehci-dbg.c
index 6e2599661b5..3be238a24cc 100644
--- a/drivers/usb/host/ehci-dbg.c
+++ b/drivers/usb/host/ehci-dbg.c
@@ -879,7 +879,7 @@ static int fill_buffer(struct debug_buffer *buf)
 	int ret = 0;
 
 	if (!buf->output_buf)
-		buf->output_buf = (char *)vmalloc(buf->alloc_size);
+		buf->output_buf = vmalloc(buf->alloc_size);
 
 	if (!buf->output_buf) {
 		ret = -ENOMEM;
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index e9062806d4a..6fee3cd58ef 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -114,6 +114,9 @@ MODULE_PARM_DESC(hird, "host initiated resume duration, +1 for each 75us\n");
 
 #define	INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
 
+/* for ASPM quirk of ISOC on AMD SB800 */
+static struct pci_dev *amd_nb_dev;
+
 /*-------------------------------------------------------------------------*/
 
 #include "ehci.h"
@@ -529,6 +532,11 @@ static void ehci_stop (struct usb_hcd *hcd)
 	spin_unlock_irq (&ehci->lock);
 	ehci_mem_cleanup (ehci);
 
+	if (amd_nb_dev) {
+		pci_dev_put(amd_nb_dev);
+		amd_nb_dev = NULL;
+	}
+
 #ifdef	EHCI_STATS
 	ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
 		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
@@ -1166,12 +1174,17 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ehci_mxc_driver
 #endif
 
+#ifdef CONFIG_CPU_SUBTYPE_SH7786
+#include "ehci-sh.c"
+#define PLATFORM_DRIVER		ehci_hcd_sh_driver
+#endif
+
 #ifdef CONFIG_SOC_AU1200
 #include "ehci-au1xxx.c"
 #define	PLATFORM_DRIVER		ehci_hcd_au1xxx_driver
 #endif
 
-#ifdef CONFIG_ARCH_OMAP3
+#ifdef CONFIG_USB_EHCI_HCD_OMAP
 #include "ehci-omap.c"
 #define        PLATFORM_DRIVER         ehci_hcd_omap_driver
 #endif
@@ -1216,6 +1229,26 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ehci_octeon_driver
 #endif
 
+#ifdef CONFIG_USB_CNS3XXX_EHCI
+#include "ehci-cns3xxx.c"
+#define PLATFORM_DRIVER		cns3xxx_ehci_driver
+#endif
+
+#ifdef CONFIG_ARCH_VT8500
+#include "ehci-vt8500.c"
+#define	PLATFORM_DRIVER		vt8500_ehci_driver
+#endif
+
+#ifdef CONFIG_PLAT_SPEAR
+#include "ehci-spear.c"
+#define PLATFORM_DRIVER		spear_ehci_hcd_driver
+#endif
+
+#ifdef CONFIG_USB_EHCI_MSM
+#include "ehci-msm.c"
+#define PLATFORM_DRIVER		ehci_msm_driver
+#endif
+
 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
     !defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c
new file mode 100644
index 00000000000..413f4deca53
--- /dev/null
+++ b/drivers/usb/host/ehci-msm.c
@@ -0,0 +1,345 @@
+/* ehci-msm.c - HSUSB Host Controller Driver Implementation
+ *
+ * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved.
+ *
+ * Partly derived from ehci-fsl.c and ehci-hcd.c
+ * Copyright (c) 2000-2004 by David Brownell
+ * Copyright (c) 2005 MontaVista Software
+ *
+ * All source code in this file is licensed under the following license except
+ * where indicated.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * See the GNU General Public License for more details.
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, you can find it at http://www.fsf.org
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+
+#include <linux/usb/otg.h>
+#include <linux/usb/msm_hsusb_hw.h>
+
+#define MSM_USB_BASE (hcd->regs)
+
+static struct otg_transceiver *otg;
+
+/*
+ * ehci_run defined in drivers/usb/host/ehci-hcd.c reset the controller and
+ * the configuration settings in ehci_msm_reset vanish after controller is
+ * reset. Resetting the controler in ehci_run seems to be un-necessary
+ * provided HCD reset the controller before calling ehci_run. Most of the HCD
+ * do but some are not. So this function is same as ehci_run but we don't
+ * reset the controller here.
+ */
+static int ehci_msm_run(struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);
+	u32			temp;
+	u32			hcc_params;
+
+	hcd->uses_new_polling = 1;
+
+	ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
+	ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next);
+
+	/*
+	 * hcc_params controls whether ehci->regs->segment must (!!!)
+	 * be used; it constrains QH/ITD/SITD and QTD locations.
+	 * pci_pool consistent memory always uses segment zero.
+	 * streaming mappings for I/O buffers, like pci_map_single(),
+	 * can return segments above 4GB, if the device allows.
+	 *
+	 * NOTE:  the dma mask is visible through dma_supported(), so
+	 * drivers can pass this info along ... like NETIF_F_HIGHDMA,
+	 * Scsi_Host.highmem_io, and so forth.  It's readonly to all
+	 * host side drivers though.
+	 */
+	hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
+	if (HCC_64BIT_ADDR(hcc_params))
+		ehci_writel(ehci, 0, &ehci->regs->segment);
+
+	/*
+	 * Philips, Intel, and maybe others need CMD_RUN before the
+	 * root hub will detect new devices (why?); NEC doesn't
+	 */
+	ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET);
+	ehci->command |= CMD_RUN;
+	ehci_writel(ehci, ehci->command, &ehci->regs->command);
+	dbg_cmd(ehci, "init", ehci->command);
+
+	/*
+	 * Start, enabling full USB 2.0 functionality ... usb 1.1 devices
+	 * are explicitly handed to companion controller(s), so no TT is
+	 * involved with the root hub.  (Except where one is integrated,
+	 * and there's no companion controller unless maybe for USB OTG.)
+	 *
+	 * Turning on the CF flag will transfer ownership of all ports
+	 * from the companions to the EHCI controller.  If any of the
+	 * companions are in the middle of a port reset at the time, it
+	 * could cause trouble.  Write-locking ehci_cf_port_reset_rwsem
+	 * guarantees that no resets are in progress.  After we set CF,
+	 * a short delay lets the hardware catch up; new resets shouldn't
+	 * be started before the port switching actions could complete.
+	 */
+	down_write(&ehci_cf_port_reset_rwsem);
+	hcd->state = HC_STATE_RUNNING;
+	ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
+	ehci_readl(ehci, &ehci->regs->command);	/* unblock posted writes */
+	usleep_range(5000, 5500);
+	up_write(&ehci_cf_port_reset_rwsem);
+	ehci->last_periodic_enable = ktime_get_real();
+
+	temp = HC_VERSION(ehci_readl(ehci, &ehci->caps->hc_capbase));
+	ehci_info(ehci,
+		"USB %x.%x started, EHCI %x.%02x%s\n",
+		((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
+		temp >> 8, temp & 0xff,
+		ignore_oc ? ", overcurrent ignored" : "");
+
+	ehci_writel(ehci, INTR_MASK,
+		    &ehci->regs->intr_enable); /* Turn On Interrupts */
+
+	/* GRR this is run-once init(), being done every time the HC starts.
+	 * So long as they're part of class devices, we can't do it init()
+	 * since the class device isn't created that early.
+	 */
+	create_debug_files(ehci);
+	create_companion_file(ehci);
+
+	return 0;
+}
+
+static int ehci_msm_reset(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int retval;
+
+	ehci->caps = USB_CAPLENGTH;
+	ehci->regs = USB_CAPLENGTH +
+		HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+
+	/* cache the data to minimize the chip reads*/
+	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+
+	hcd->has_tt = 1;
+	ehci->sbrn = HCD_USB2;
+
+	/* data structure init */
+	retval = ehci_init(hcd);
+	if (retval)
+		return retval;
+
+	retval = ehci_reset(ehci);
+	if (retval)
+		return retval;
+
+	/* bursts of unspecified length. */
+	writel(0, USB_AHBBURST);
+	/* Use the AHB transactor */
+	writel(0, USB_AHBMODE);
+	/* Disable streaming mode and select host mode */
+	writel(0x13, USB_USBMODE);
+
+	ehci_port_power(ehci, 1);
+	return 0;
+}
+
+static struct hc_driver msm_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "Qualcomm On-Chip EHCI Host Controller",
+	.hcd_priv_size		= sizeof(struct ehci_hcd),
+
+	/*
+	 * generic hardware linkage
+	 */
+	.irq			= ehci_irq,
+	.flags			= HCD_USB2 | HCD_MEMORY,
+
+	.reset			= ehci_msm_reset,
+	.start			= ehci_msm_run,
+
+	.stop			= ehci_stop,
+	.shutdown		= ehci_shutdown,
+
+	/*
+	 * managing i/o requests and associated device resources
+	 */
+	.urb_enqueue		= ehci_urb_enqueue,
+	.urb_dequeue		= ehci_urb_dequeue,
+	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
+	.clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
+
+	/*
+	 * scheduling support
+	 */
+	.get_frame_number	= ehci_get_frame,
+
+	/*
+	 * root hub support
+	 */
+	.hub_status_data	= ehci_hub_status_data,
+	.hub_control		= ehci_hub_control,
+	.relinquish_port	= ehci_relinquish_port,
+	.port_handed_over	= ehci_port_handed_over,
+
+	/*
+	 * PM support
+	 */
+	.bus_suspend		= ehci_bus_suspend,
+	.bus_resume		= ehci_bus_resume,
+};
+
+static int ehci_msm_probe(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd;
+	struct resource *res;
+	int ret;
+
+	dev_dbg(&pdev->dev, "ehci_msm proble\n");
+
+	hcd = usb_create_hcd(&msm_hc_driver, &pdev->dev, dev_name(&pdev->dev));
+	if (!hcd) {
+		dev_err(&pdev->dev, "Unable to create HCD\n");
+		return  -ENOMEM;
+	}
+
+	hcd->irq = platform_get_irq(pdev, 0);
+	if (hcd->irq < 0) {
+		dev_err(&pdev->dev, "Unable to get IRQ resource\n");
+		ret = hcd->irq;
+		goto put_hcd;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "Unable to get memory resource\n");
+		ret = -ENODEV;
+		goto put_hcd;
+	}
+
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (!hcd->regs) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		ret = -ENOMEM;
+		goto put_hcd;
+	}
+
+	/*
+	 * OTG driver takes care of PHY initialization, clock management,
+	 * powering up VBUS, mapping of registers address space and power
+	 * management.
+	 */
+	otg = otg_get_transceiver();
+	if (!otg) {
+		dev_err(&pdev->dev, "unable to find transceiver\n");
+		ret = -ENODEV;
+		goto unmap;
+	}
+
+	ret = otg_set_host(otg, &hcd->self);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "unable to register with transceiver\n");
+		goto put_transceiver;
+	}
+
+	device_init_wakeup(&pdev->dev, 1);
+	/*
+	 * OTG device parent of HCD takes care of putting
+	 * hardware into low power mode.
+	 */
+	pm_runtime_no_callbacks(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
+	return 0;
+
+put_transceiver:
+	otg_put_transceiver(otg);
+unmap:
+	iounmap(hcd->regs);
+put_hcd:
+	usb_put_hcd(hcd);
+
+	return ret;
+}
+
+static int __devexit ehci_msm_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	device_init_wakeup(&pdev->dev, 0);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+
+	otg_set_host(otg, NULL);
+	otg_put_transceiver(otg);
+
+	usb_put_hcd(hcd);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int ehci_msm_pm_suspend(struct device *dev)
+{
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
+	bool wakeup = device_may_wakeup(dev);
+
+	dev_dbg(dev, "ehci-msm PM suspend\n");
+
+	/*
+	 * EHCI helper function has also the same check before manipulating
+	 * port wakeup flags.  We do check here the same condition before
+	 * calling the same helper function to avoid bringing hardware
+	 * from Low power mode when there is no need for adjusting port
+	 * wakeup flags.
+	 */
+	if (hcd->self.root_hub->do_remote_wakeup && !wakeup) {
+		pm_runtime_resume(dev);
+		ehci_prepare_ports_for_controller_suspend(hcd_to_ehci(hcd),
+				wakeup);
+	}
+
+	return 0;
+}
+
+static int ehci_msm_pm_resume(struct device *dev)
+{
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
+
+	dev_dbg(dev, "ehci-msm PM resume\n");
+	ehci_prepare_ports_for_controller_resume(hcd_to_ehci(hcd));
+
+	return 0;
+}
+#else
+#define ehci_msm_pm_suspend	NULL
+#define ehci_msm_pm_resume	NULL
+#endif
+
+static const struct dev_pm_ops ehci_msm_dev_pm_ops = {
+	.suspend         = ehci_msm_pm_suspend,
+	.resume          = ehci_msm_pm_resume,
+};
+
+static struct platform_driver ehci_msm_driver = {
+	.probe	= ehci_msm_probe,
+	.remove	= __devexit_p(ehci_msm_remove),
+	.driver = {
+		   .name = "msm_hsusb_host",
+		   .pm = &ehci_msm_dev_pm_ops,
+	},
+};
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index bce85055019..fa59b26fc5b 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -28,7 +28,7 @@
 #define ULPI_VIEWPORT_OFFSET	0x170
 
 struct ehci_mxc_priv {
-	struct clk *usbclk, *ahbclk;
+	struct clk *usbclk, *ahbclk, *phy1clk;
 	struct usb_hcd *hcd;
 };
 
@@ -36,14 +36,8 @@ struct ehci_mxc_priv {
 static int ehci_mxc_setup(struct usb_hcd *hcd)
 {
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-	struct device *dev = hcd->self.controller;
-	struct mxc_usbh_platform_data *pdata = dev_get_platdata(dev);
 	int retval;
 
-	/* EHCI registers start at offset 0x100 */
-	ehci->caps = hcd->regs + 0x100;
-	ehci->regs = hcd->regs + 0x100 +
-	    HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
 	dbg_hcs_params(ehci, "reset");
 	dbg_hcc_params(ehci, "reset");
 
@@ -65,12 +59,6 @@ static int ehci_mxc_setup(struct usb_hcd *hcd)
 
 	ehci_reset(ehci);
 
-	/* set up the PORTSCx register */
-	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
-
-	/* is this really needed? */
-	msleep(10);
-
 	ehci_port_power(ehci, 0);
 	return 0;
 }
@@ -100,6 +88,7 @@ static const struct hc_driver ehci_mxc_hc_driver = {
 	.urb_enqueue = ehci_urb_enqueue,
 	.urb_dequeue = ehci_urb_dequeue,
 	.endpoint_disable = ehci_endpoint_disable,
+	.endpoint_reset = ehci_endpoint_reset,
 
 	/*
 	 * scheduling support
@@ -115,6 +104,8 @@ static const struct hc_driver ehci_mxc_hc_driver = {
 	.bus_resume = ehci_bus_resume,
 	.relinquish_port = ehci_relinquish_port,
 	.port_handed_over = ehci_port_handed_over,
+
+	.clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
 };
 
 static int ehci_mxc_drv_probe(struct platform_device *pdev)
@@ -125,6 +116,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 	int irq, ret;
 	struct ehci_mxc_priv *priv;
 	struct device *dev = &pdev->dev;
+	struct ehci_hcd *ehci;
 
 	dev_info(&pdev->dev, "initializing i.MX USB Controller\n");
 
@@ -168,17 +160,6 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 		goto err_ioremap;
 	}
 
-	/* call platform specific init function */
-	if (pdata->init) {
-		ret = pdata->init(pdev);
-		if (ret) {
-			dev_err(dev, "platform init failed\n");
-			goto err_init;
-		}
-		/* platforms need some time to settle changed IO settings */
-		mdelay(10);
-	}
-
 	/* enable clocks */
 	priv->usbclk = clk_get(dev, "usb");
 	if (IS_ERR(priv->usbclk)) {
@@ -196,11 +177,46 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 		clk_enable(priv->ahbclk);
 	}
 
+	/* "dr" device has its own clock */
+	if (pdev->id == 0) {
+		priv->phy1clk = clk_get(dev, "usb_phy1");
+		if (IS_ERR(priv->phy1clk)) {
+			ret = PTR_ERR(priv->phy1clk);
+			goto err_clk_phy;
+		}
+		clk_enable(priv->phy1clk);
+	}
+
+
+	/* call platform specific init function */
+	if (pdata->init) {
+		ret = pdata->init(pdev);
+		if (ret) {
+			dev_err(dev, "platform init failed\n");
+			goto err_init;
+		}
+		/* platforms need some time to settle changed IO settings */
+		mdelay(10);
+	}
+
 	/* setup specific usb hw */
 	ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
 	if (ret < 0)
 		goto err_init;
 
+	ehci = hcd_to_ehci(hcd);
+
+	/* EHCI registers start at offset 0x100 */
+	ehci->caps = hcd->regs + 0x100;
+	ehci->regs = hcd->regs + 0x100 +
+	    HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+
+	/* set up the PORTSCx register */
+	ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]);
+
+	/* is this really needed? */
+	msleep(10);
+
 	/* Initialize the transceiver */
 	if (pdata->otg) {
 		pdata->otg->io_priv = hcd->regs + ULPI_VIEWPORT_OFFSET;
@@ -230,6 +246,11 @@ err_add:
 	if (pdata && pdata->exit)
 		pdata->exit(pdev);
 err_init:
+	if (priv->phy1clk) {
+		clk_disable(priv->phy1clk);
+		clk_put(priv->phy1clk);
+	}
+err_clk_phy:
 	if (priv->ahbclk) {
 		clk_disable(priv->ahbclk);
 		clk_put(priv->ahbclk);
@@ -273,6 +294,10 @@ static int __exit ehci_mxc_drv_remove(struct platform_device *pdev)
 		clk_disable(priv->ahbclk);
 		clk_put(priv->ahbclk);
 	}
+	if (priv->phy1clk) {
+		clk_disable(priv->phy1clk);
+		clk_put(priv->phy1clk);
+	}
 
 	kfree(priv);
 
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 116ae280053..680f2ef4e59 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -1,11 +1,12 @@
 /*
- * ehci-omap.c - driver for USBHOST on OMAP 34xx processor
+ * ehci-omap.c - driver for USBHOST on OMAP3/4 processors
  *
- * Bus Glue for OMAP34xx USBHOST 3 port EHCI controller
- * Tested on OMAP3430 ES2.0 SDP
+ * Bus Glue for the EHCI controllers in OMAP3/4
+ * Tested on several OMAP3 boards, and OMAP4 Pandaboard
  *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
+ * Copyright (C) 2007-2010 Texas Instruments, Inc.
  *	Author: Vikram Pandita <vikram.pandita@ti.com>
+ *	Author: Anand Gadiyar <gadiyar@ti.com>
  *
  * Copyright (C) 2009 Nokia Corporation
  *	Contact: Felipe Balbi <felipe.balbi@nokia.com>
@@ -26,11 +27,14 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
  *
- * TODO (last updated Feb 12, 2010):
+ * TODO (last updated Nov 21, 2010):
  *	- add kernel-doc
  *	- enable AUTOIDLE
  *	- add suspend/resume
  *	- move workarounds to board-files
+ *	- factor out code common to OHCI
+ *	- add HSIC and TLL support
+ *	- convert to use hwmod and runtime PM
  */
 
 #include <linux/platform_device.h>
@@ -86,9 +90,9 @@
 #define	OMAP_TLL_ULPI_SCRATCH_REGISTER(num)		(0x816 + 0x100 * num)
 
 #define OMAP_TLL_CHANNEL_COUNT				3
-#define OMAP_TLL_CHANNEL_1_EN_MASK			(1 << 1)
-#define OMAP_TLL_CHANNEL_2_EN_MASK			(1 << 2)
-#define OMAP_TLL_CHANNEL_3_EN_MASK			(1 << 4)
+#define OMAP_TLL_CHANNEL_1_EN_MASK			(1 << 0)
+#define OMAP_TLL_CHANNEL_2_EN_MASK			(1 << 1)
+#define OMAP_TLL_CHANNEL_3_EN_MASK			(1 << 2)
 
 /* UHH Register Set */
 #define	OMAP_UHH_REVISION				(0x00)
@@ -114,6 +118,23 @@
 #define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS		(1 << 9)
 #define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS		(1 << 10)
 
+/* OMAP4-specific defines */
+#define OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR		(3 << 2)
+#define OMAP4_UHH_SYSCONFIG_NOIDLE			(1 << 2)
+
+#define OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR		(3 << 4)
+#define OMAP4_UHH_SYSCONFIG_NOSTDBY			(1 << 4)
+#define OMAP4_UHH_SYSCONFIG_SOFTRESET			(1 << 0)
+
+#define OMAP4_P1_MODE_CLEAR				(3 << 16)
+#define OMAP4_P1_MODE_TLL				(1 << 16)
+#define OMAP4_P1_MODE_HSIC				(3 << 16)
+#define OMAP4_P2_MODE_CLEAR				(3 << 18)
+#define OMAP4_P2_MODE_TLL				(1 << 18)
+#define OMAP4_P2_MODE_HSIC				(3 << 18)
+
+#define OMAP_REV2_TLL_CHANNEL_COUNT			2
+
 #define	OMAP_UHH_DEBUG_CSR				(0x44)
 
 /* EHCI Register Set */
@@ -127,6 +148,17 @@
 #define	EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT		8
 #define	EHCI_INSNREG05_ULPI_WRDATA_SHIFT		0
 
+/* Values of UHH_REVISION - Note: these are not given in the TRM */
+#define OMAP_EHCI_REV1	0x00000010	/* OMAP3 */
+#define OMAP_EHCI_REV2	0x50700100	/* OMAP4 */
+
+#define is_omap_ehci_rev1(x)	(x->omap_ehci_rev == OMAP_EHCI_REV1)
+#define is_omap_ehci_rev2(x)	(x->omap_ehci_rev == OMAP_EHCI_REV2)
+
+#define is_ehci_phy_mode(x)	(x == EHCI_HCD_OMAP_MODE_PHY)
+#define is_ehci_tll_mode(x)	(x == EHCI_HCD_OMAP_MODE_TLL)
+#define is_ehci_hsic_mode(x)	(x == EHCI_HCD_OMAP_MODE_HSIC)
+
 /*-------------------------------------------------------------------------*/
 
 static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val)
@@ -156,10 +188,14 @@ struct ehci_hcd_omap {
 	struct device		*dev;
 
 	struct clk		*usbhost_ick;
-	struct clk		*usbhost2_120m_fck;
-	struct clk		*usbhost1_48m_fck;
+	struct clk		*usbhost_hs_fck;
+	struct clk		*usbhost_fs_fck;
 	struct clk		*usbtll_fck;
 	struct clk		*usbtll_ick;
+	struct clk		*xclk60mhsp1_ck;
+	struct clk		*xclk60mhsp2_ck;
+	struct clk		*utmi_p1_fck;
+	struct clk		*utmi_p2_fck;
 
 	/* FIXME the following two workarounds are
 	 * board specific not silicon-specific so these
@@ -176,6 +212,9 @@ struct ehci_hcd_omap {
 	/* phy reset workaround */
 	int			phy_reset;
 
+	/* IP revision */
+	u32			omap_ehci_rev;
+
 	/* desired phy_mode: TLL, PHY */
 	enum ehci_hcd_omap_mode	port_mode[OMAP3_HS_USB_PORTS];
 
@@ -191,13 +230,14 @@ struct ehci_hcd_omap {
 
 /*-------------------------------------------------------------------------*/
 
-static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask)
+static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask,
+				u8 tll_channel_count)
 {
 	unsigned reg;
 	int i;
 
 	/* Program the 3 TLL channels upfront */
-	for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) {
+	for (i = 0; i < tll_channel_count; i++) {
 		reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
 
 		/* Disable AutoIdle, BitStuffing and use SDR Mode */
@@ -217,7 +257,7 @@ static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask)
 	ehci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg);
 
 	/* Enable channels now */
-	for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) {
+	for (i = 0; i < tll_channel_count; i++) {
 		reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
 
 		/* Enable only the reg that is needed */
@@ -286,19 +326,19 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 	}
 	clk_enable(omap->usbhost_ick);
 
-	omap->usbhost2_120m_fck = clk_get(omap->dev, "usbhost_120m_fck");
-	if (IS_ERR(omap->usbhost2_120m_fck)) {
-		ret = PTR_ERR(omap->usbhost2_120m_fck);
+	omap->usbhost_hs_fck = clk_get(omap->dev, "hs_fck");
+	if (IS_ERR(omap->usbhost_hs_fck)) {
+		ret = PTR_ERR(omap->usbhost_hs_fck);
 		goto err_host_120m_fck;
 	}
-	clk_enable(omap->usbhost2_120m_fck);
+	clk_enable(omap->usbhost_hs_fck);
 
-	omap->usbhost1_48m_fck = clk_get(omap->dev, "usbhost_48m_fck");
-	if (IS_ERR(omap->usbhost1_48m_fck)) {
-		ret = PTR_ERR(omap->usbhost1_48m_fck);
+	omap->usbhost_fs_fck = clk_get(omap->dev, "fs_fck");
+	if (IS_ERR(omap->usbhost_fs_fck)) {
+		ret = PTR_ERR(omap->usbhost_fs_fck);
 		goto err_host_48m_fck;
 	}
-	clk_enable(omap->usbhost1_48m_fck);
+	clk_enable(omap->usbhost_fs_fck);
 
 	if (omap->phy_reset) {
 		/* Refer: ISSUE1 */
@@ -333,6 +373,80 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 	}
 	clk_enable(omap->usbtll_ick);
 
+	omap->omap_ehci_rev = ehci_omap_readl(omap->uhh_base,
+						OMAP_UHH_REVISION);
+	dev_dbg(omap->dev, "OMAP UHH_REVISION 0x%x\n",
+					omap->omap_ehci_rev);
+
+	/*
+	 * Enable per-port clocks as needed (newer controllers only).
+	 * - External ULPI clock for PHY mode
+	 * - Internal clocks for TLL and HSIC modes (TODO)
+	 */
+	if (is_omap_ehci_rev2(omap)) {
+		switch (omap->port_mode[0]) {
+		case EHCI_HCD_OMAP_MODE_PHY:
+			omap->xclk60mhsp1_ck = clk_get(omap->dev,
+							"xclk60mhsp1_ck");
+			if (IS_ERR(omap->xclk60mhsp1_ck)) {
+				ret = PTR_ERR(omap->xclk60mhsp1_ck);
+				dev_err(omap->dev,
+					"Unable to get Port1 ULPI clock\n");
+			}
+
+			omap->utmi_p1_fck = clk_get(omap->dev,
+							"utmi_p1_gfclk");
+			if (IS_ERR(omap->utmi_p1_fck)) {
+				ret = PTR_ERR(omap->utmi_p1_fck);
+				dev_err(omap->dev,
+					"Unable to get utmi_p1_fck\n");
+			}
+
+			ret = clk_set_parent(omap->utmi_p1_fck,
+						omap->xclk60mhsp1_ck);
+			if (ret != 0) {
+				dev_err(omap->dev,
+					"Unable to set P1 f-clock\n");
+			}
+			break;
+		case EHCI_HCD_OMAP_MODE_TLL:
+			/* TODO */
+		default:
+			break;
+		}
+		switch (omap->port_mode[1]) {
+		case EHCI_HCD_OMAP_MODE_PHY:
+			omap->xclk60mhsp2_ck = clk_get(omap->dev,
+							"xclk60mhsp2_ck");
+			if (IS_ERR(omap->xclk60mhsp2_ck)) {
+				ret = PTR_ERR(omap->xclk60mhsp2_ck);
+				dev_err(omap->dev,
+					"Unable to get Port2 ULPI clock\n");
+			}
+
+			omap->utmi_p2_fck = clk_get(omap->dev,
+							"utmi_p2_gfclk");
+			if (IS_ERR(omap->utmi_p2_fck)) {
+				ret = PTR_ERR(omap->utmi_p2_fck);
+				dev_err(omap->dev,
+					"Unable to get utmi_p2_fck\n");
+			}
+
+			ret = clk_set_parent(omap->utmi_p2_fck,
+						omap->xclk60mhsp2_ck);
+			if (ret != 0) {
+				dev_err(omap->dev,
+					"Unable to set P2 f-clock\n");
+			}
+			break;
+		case EHCI_HCD_OMAP_MODE_TLL:
+			/* TODO */
+		default:
+			break;
+		}
+	}
+
+
 	/* perform TLL soft reset, and wait until reset is complete */
 	ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
 			OMAP_USBTLL_SYSCONFIG_SOFTRESET);
@@ -360,12 +474,20 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 
 	/* Put UHH in NoIdle/NoStandby mode */
 	reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
-	reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
-			| OMAP_UHH_SYSCONFIG_SIDLEMODE
-			| OMAP_UHH_SYSCONFIG_CACTIVITY
-			| OMAP_UHH_SYSCONFIG_MIDLEMODE);
-	reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
+	if (is_omap_ehci_rev1(omap)) {
+		reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
+				| OMAP_UHH_SYSCONFIG_SIDLEMODE
+				| OMAP_UHH_SYSCONFIG_CACTIVITY
+				| OMAP_UHH_SYSCONFIG_MIDLEMODE);
+		reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
+
 
+	} else if (is_omap_ehci_rev2(omap)) {
+		reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR;
+		reg |= OMAP4_UHH_SYSCONFIG_NOIDLE;
+		reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR;
+		reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY;
+	}
 	ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
 
 	reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
@@ -376,40 +498,56 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 			| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
 	reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
 
-	if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
-	if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
-	if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
-	/* Bypass the TLL module for PHY mode operation */
-	if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
-		dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
-		if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) ||
-			(omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) ||
-				(omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY))
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
-		else
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
-	} else {
-		dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
-		if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-		else if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL)
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
-		if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-		else if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL)
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
-		if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
-		else if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+	if (is_omap_ehci_rev1(omap)) {
+		if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+			reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
+		if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+			reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
+		if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+			reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
+
+		/* Bypass the TLL module for PHY mode operation */
+		if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
+			dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
+			if (is_ehci_phy_mode(omap->port_mode[0]) ||
+				is_ehci_phy_mode(omap->port_mode[1]) ||
+					is_ehci_phy_mode(omap->port_mode[2]))
+				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
+			else
+				reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
+		} else {
+			dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
+			if (is_ehci_phy_mode(omap->port_mode[0]))
+				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+			else if (is_ehci_tll_mode(omap->port_mode[0]))
+				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+
+			if (is_ehci_phy_mode(omap->port_mode[1]))
+				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+			else if (is_ehci_tll_mode(omap->port_mode[1]))
+				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+
+			if (is_ehci_phy_mode(omap->port_mode[2]))
+				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+			else if (is_ehci_tll_mode(omap->port_mode[2]))
+				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+		}
+	} else if (is_omap_ehci_rev2(omap)) {
+		/* Clear port mode fields for PHY mode*/
+		reg &= ~OMAP4_P1_MODE_CLEAR;
+		reg &= ~OMAP4_P2_MODE_CLEAR;
+
+		if (is_ehci_tll_mode(omap->port_mode[0]))
+			reg |= OMAP4_P1_MODE_TLL;
+		else if (is_ehci_hsic_mode(omap->port_mode[0]))
+			reg |= OMAP4_P1_MODE_HSIC;
 
+		if (is_ehci_tll_mode(omap->port_mode[1]))
+			reg |= OMAP4_P2_MODE_TLL;
+		else if (is_ehci_hsic_mode(omap->port_mode[1]))
+			reg |= OMAP4_P2_MODE_HSIC;
 	}
+
 	ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
 	dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
 
@@ -438,7 +576,7 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 			tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK;
 
 		/* Enable UTMI mode for required TLL channels */
-		omap_usb_utmi_init(omap, tll_ch_mask);
+		omap_usb_utmi_init(omap, tll_ch_mask, OMAP_TLL_CHANNEL_COUNT);
 	}
 
 	if (omap->phy_reset) {
@@ -464,6 +602,14 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 	return 0;
 
 err_sys_status:
+	clk_disable(omap->utmi_p2_fck);
+	clk_put(omap->utmi_p2_fck);
+	clk_disable(omap->xclk60mhsp2_ck);
+	clk_put(omap->xclk60mhsp2_ck);
+	clk_disable(omap->utmi_p1_fck);
+	clk_put(omap->utmi_p1_fck);
+	clk_disable(omap->xclk60mhsp1_ck);
+	clk_put(omap->xclk60mhsp1_ck);
 	clk_disable(omap->usbtll_ick);
 	clk_put(omap->usbtll_ick);
 
@@ -472,8 +618,8 @@ err_tll_ick:
 	clk_put(omap->usbtll_fck);
 
 err_tll_fck:
-	clk_disable(omap->usbhost1_48m_fck);
-	clk_put(omap->usbhost1_48m_fck);
+	clk_disable(omap->usbhost_fs_fck);
+	clk_put(omap->usbhost_fs_fck);
 
 	if (omap->phy_reset) {
 		if (gpio_is_valid(omap->reset_gpio_port[0]))
@@ -484,8 +630,8 @@ err_tll_fck:
 	}
 
 err_host_48m_fck:
-	clk_disable(omap->usbhost2_120m_fck);
-	clk_put(omap->usbhost2_120m_fck);
+	clk_disable(omap->usbhost_hs_fck);
+	clk_put(omap->usbhost_hs_fck);
 
 err_host_120m_fck:
 	clk_disable(omap->usbhost_ick);
@@ -503,6 +649,8 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 
 	/* Reset OMAP modules for insmod/rmmod to work */
 	ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG,
+			is_omap_ehci_rev2(omap) ?
+			OMAP4_UHH_SYSCONFIG_SOFTRESET :
 			OMAP_UHH_SYSCONFIG_SOFTRESET);
 	while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
 				& (1 << 0))) {
@@ -550,16 +698,16 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 		omap->usbhost_ick = NULL;
 	}
 
-	if (omap->usbhost1_48m_fck != NULL) {
-		clk_disable(omap->usbhost1_48m_fck);
-		clk_put(omap->usbhost1_48m_fck);
-		omap->usbhost1_48m_fck = NULL;
+	if (omap->usbhost_fs_fck != NULL) {
+		clk_disable(omap->usbhost_fs_fck);
+		clk_put(omap->usbhost_fs_fck);
+		omap->usbhost_fs_fck = NULL;
 	}
 
-	if (omap->usbhost2_120m_fck != NULL) {
-		clk_disable(omap->usbhost2_120m_fck);
-		clk_put(omap->usbhost2_120m_fck);
-		omap->usbhost2_120m_fck = NULL;
+	if (omap->usbhost_hs_fck != NULL) {
+		clk_disable(omap->usbhost_hs_fck);
+		clk_put(omap->usbhost_hs_fck);
+		omap->usbhost_hs_fck = NULL;
 	}
 
 	if (omap->usbtll_ick != NULL) {
@@ -568,6 +716,32 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
 		omap->usbtll_ick = NULL;
 	}
 
+	if (is_omap_ehci_rev2(omap)) {
+		if (omap->xclk60mhsp1_ck != NULL) {
+			clk_disable(omap->xclk60mhsp1_ck);
+			clk_put(omap->xclk60mhsp1_ck);
+			omap->xclk60mhsp1_ck = NULL;
+		}
+
+		if (omap->utmi_p1_fck != NULL) {
+			clk_disable(omap->utmi_p1_fck);
+			clk_put(omap->utmi_p1_fck);
+			omap->utmi_p1_fck = NULL;
+		}
+
+		if (omap->xclk60mhsp2_ck != NULL) {
+			clk_disable(omap->xclk60mhsp2_ck);
+			clk_put(omap->xclk60mhsp2_ck);
+			omap->xclk60mhsp2_ck = NULL;
+		}
+
+		if (omap->utmi_p2_fck != NULL) {
+			clk_disable(omap->utmi_p2_fck);
+			clk_put(omap->utmi_p2_fck);
+			omap->utmi_p2_fck = NULL;
+		}
+	}
+
 	if (omap->phy_reset) {
 		if (gpio_is_valid(omap->reset_gpio_port[0]))
 			gpio_free(omap->reset_gpio_port[0]);
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 655f3c9f88b..76179c39c0e 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -22,6 +22,9 @@
 #error "This file is PCI bus glue.  CONFIG_PCI must be defined."
 #endif
 
+/* defined here to avoid adding to pci_ids.h for single instance use */
+#define PCI_DEVICE_ID_INTEL_CE4100_USB	0x2e70
+
 /*-------------------------------------------------------------------------*/
 
 /* called after powerup, by probe or system-pm "wakeup" */
@@ -41,6 +44,35 @@ static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev)
 	return 0;
 }
 
+static int ehci_quirk_amd_SB800(struct ehci_hcd *ehci)
+{
+	struct pci_dev *amd_smbus_dev;
+	u8 rev = 0;
+
+	amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, 0x4385, NULL);
+	if (!amd_smbus_dev)
+		return 0;
+
+	pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev);
+	if (rev < 0x40) {
+		pci_dev_put(amd_smbus_dev);
+		amd_smbus_dev = NULL;
+		return 0;
+	}
+
+	if (!amd_nb_dev)
+		amd_nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL);
+	if (!amd_nb_dev)
+		ehci_err(ehci, "QUIRK: unable to get AMD NB device\n");
+
+	ehci_info(ehci, "QUIRK: Enable AMD SB800 L1 fix\n");
+
+	pci_dev_put(amd_smbus_dev);
+	amd_smbus_dev = NULL;
+
+	return 1;
+}
+
 /* called during probe() after chip reset completes */
 static int ehci_pci_setup(struct usb_hcd *hcd)
 {
@@ -99,6 +131,9 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 	/* cache this readonly data; minimize chip reads */
 	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
 
+	if (ehci_quirk_amd_SB800(ehci))
+		ehci->amd_l1_fix = 1;
+
 	retval = ehci_halt(ehci);
 	if (retval)
 		return retval;
@@ -137,6 +172,10 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 			ehci_info(ehci, "disable lpm for langwell/penwell\n");
 			ehci->has_lpm = 0;
 		}
+		if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB) {
+			hcd->has_tt = 1;
+			tdi_reset(ehci);
+		}
 		break;
 	case PCI_VENDOR_ID_TDI:
 		if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c
index d9f78eb2657..aa46f57f9ec 100644
--- a/drivers/usb/host/ehci-sched.c
+++ b/drivers/usb/host/ehci-sched.c
@@ -1590,6 +1590,63 @@ itd_link (struct ehci_hcd *ehci, unsigned frame, struct ehci_itd *itd)
 	*hw_p = cpu_to_hc32(ehci, itd->itd_dma | Q_TYPE_ITD);
 }
 
+#define AB_REG_BAR_LOW 0xe0
+#define AB_REG_BAR_HIGH 0xe1
+#define AB_INDX(addr) ((addr) + 0x00)
+#define AB_DATA(addr) ((addr) + 0x04)
+#define NB_PCIE_INDX_ADDR 0xe0
+#define NB_PCIE_INDX_DATA 0xe4
+#define NB_PIF0_PWRDOWN_0 0x01100012
+#define NB_PIF0_PWRDOWN_1 0x01100013
+
+static void ehci_quirk_amd_L1(struct ehci_hcd *ehci, int disable)
+{
+	u32 addr, addr_low, addr_high, val;
+
+	outb_p(AB_REG_BAR_LOW, 0xcd6);
+	addr_low = inb_p(0xcd7);
+	outb_p(AB_REG_BAR_HIGH, 0xcd6);
+	addr_high = inb_p(0xcd7);
+	addr = addr_high << 8 | addr_low;
+	outl_p(0x30, AB_INDX(addr));
+	outl_p(0x40, AB_DATA(addr));
+	outl_p(0x34, AB_INDX(addr));
+	val = inl_p(AB_DATA(addr));
+
+	if (disable) {
+		val &= ~0x8;
+		val |= (1 << 4) | (1 << 9);
+	} else {
+		val |= 0x8;
+		val &= ~((1 << 4) | (1 << 9));
+	}
+	outl_p(val, AB_DATA(addr));
+
+	if (amd_nb_dev) {
+		addr = NB_PIF0_PWRDOWN_0;
+		pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_ADDR, addr);
+		pci_read_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, &val);
+		if (disable)
+			val &= ~(0x3f << 7);
+		else
+			val |= 0x3f << 7;
+
+		pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, val);
+
+		addr = NB_PIF0_PWRDOWN_1;
+		pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_ADDR, addr);
+		pci_read_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, &val);
+		if (disable)
+			val &= ~(0x3f << 7);
+		else
+			val |= 0x3f << 7;
+
+		pci_write_config_dword(amd_nb_dev, NB_PCIE_INDX_DATA, val);
+	}
+
+	return;
+}
+
 /* fit urb's itds into the selected schedule slot; activate as needed */
 static int
 itd_link_urb (
@@ -1616,6 +1673,12 @@ itd_link_urb (
 			urb->interval,
 			next_uframe >> 3, next_uframe & 0x7);
 	}
+
+	if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) {
+		if (ehci->amd_l1_fix == 1)
+			ehci_quirk_amd_L1(ehci, 1);
+	}
+
 	ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs++;
 
 	/* fill iTDs uframe by uframe */
@@ -1740,6 +1803,11 @@ itd_complete (
 	(void) disable_periodic(ehci);
 	ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs--;
 
+	if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) {
+		if (ehci->amd_l1_fix == 1)
+			ehci_quirk_amd_L1(ehci, 0);
+	}
+
 	if (unlikely(list_is_singular(&stream->td_list))) {
 		ehci_to_hcd(ehci)->self.bandwidth_allocated
 				-= stream->bandwidth;
@@ -2025,6 +2093,12 @@ sitd_link_urb (
 			(next_uframe >> 3) & (ehci->periodic_size - 1),
 			stream->interval, hc32_to_cpu(ehci, stream->splits));
 	}
+
+	if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) {
+		if (ehci->amd_l1_fix == 1)
+			ehci_quirk_amd_L1(ehci, 1);
+	}
+
 	ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs++;
 
 	/* fill sITDs frame by frame */
@@ -2125,6 +2199,11 @@ sitd_complete (
 	(void) disable_periodic(ehci);
 	ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs--;
 
+	if (ehci_to_hcd(ehci)->self.bandwidth_isoc_reqs == 0) {
+		if (ehci->amd_l1_fix == 1)
+			ehci_quirk_amd_L1(ehci, 0);
+	}
+
 	if (list_is_singular(&stream->td_list)) {
 		ehci_to_hcd(ehci)->self.bandwidth_allocated
 				-= stream->bandwidth;
diff --git a/drivers/usb/host/ehci-sh.c b/drivers/usb/host/ehci-sh.c
new file mode 100644
index 00000000000..595f70f42b5
--- /dev/null
+++ b/drivers/usb/host/ehci-sh.c
@@ -0,0 +1,243 @@
+/*
+ * SuperH EHCI host controller driver
+ *
+ * Copyright (C) 2010  Paul Mundt
+ *
+ * Based on ohci-sh.c and ehci-atmel.c.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+
+struct ehci_sh_priv {
+	struct clk *iclk, *fclk;
+	struct usb_hcd *hcd;
+};
+
+static int ehci_sh_reset(struct usb_hcd *hcd)
+{
+	struct ehci_hcd	*ehci = hcd_to_ehci(hcd);
+	int ret;
+
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs + HC_LENGTH(ehci_readl(ehci,
+		&ehci->caps->hc_capbase));
+
+	dbg_hcs_params(ehci, "reset");
+	dbg_hcc_params(ehci, "reset");
+
+	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+
+	ret = ehci_halt(ehci);
+	if (unlikely(ret))
+		return ret;
+
+	ret = ehci_init(hcd);
+	if (unlikely(ret))
+		return ret;
+
+	ehci->sbrn = 0x20;
+
+	ehci_reset(ehci);
+	ehci_port_power(ehci, 0);
+
+	return ret;
+}
+
+static const struct hc_driver ehci_sh_hc_driver = {
+	.description			= hcd_name,
+	.product_desc			= "SuperH EHCI",
+	.hcd_priv_size			= sizeof(struct ehci_hcd),
+
+	/*
+	 * generic hardware linkage
+	 */
+	.irq				= ehci_irq,
+	.flags				= HCD_USB2 | HCD_MEMORY,
+
+	/*
+	 * basic lifecycle operations
+	 */
+	.reset				= ehci_sh_reset,
+	.start				= ehci_run,
+	.stop				= ehci_stop,
+	.shutdown			= ehci_shutdown,
+
+	/*
+	 * managing i/o requests and associated device resources
+	 */
+	.urb_enqueue			= ehci_urb_enqueue,
+	.urb_dequeue			= ehci_urb_dequeue,
+	.endpoint_disable		= ehci_endpoint_disable,
+	.endpoint_reset			= ehci_endpoint_reset,
+
+	/*
+	 * scheduling support
+	 */
+	.get_frame_number		= ehci_get_frame,
+
+	/*
+	 * root hub support
+	 */
+	.hub_status_data		= ehci_hub_status_data,
+	.hub_control			= ehci_hub_control,
+
+#ifdef CONFIG_PM
+	.bus_suspend			= ehci_bus_suspend,
+	.bus_resume			= ehci_bus_resume,
+#endif
+
+	.relinquish_port		= ehci_relinquish_port,
+	.port_handed_over		= ehci_port_handed_over,
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
+};
+
+static int ehci_hcd_sh_probe(struct platform_device *pdev)
+{
+	const struct hc_driver *driver = &ehci_sh_hc_driver;
+	struct resource *res;
+	struct ehci_sh_priv *priv;
+	struct usb_hcd *hcd;
+	int irq, ret;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev,
+			"Found HC with no register addr. Check %s setup!\n",
+			dev_name(&pdev->dev));
+		ret = -ENODEV;
+		goto fail_create_hcd;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq <= 0) {
+		dev_err(&pdev->dev,
+			"Found HC with no IRQ. Check %s setup!\n",
+			dev_name(&pdev->dev));
+		ret = -ENODEV;
+		goto fail_create_hcd;
+	}
+
+	/* initialize hcd */
+	hcd = usb_create_hcd(&ehci_sh_hc_driver, &pdev->dev,
+			     dev_name(&pdev->dev));
+	if (!hcd) {
+		ret = -ENOMEM;
+		goto fail_create_hcd;
+	}
+
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+				driver->description)) {
+		dev_dbg(&pdev->dev, "controller already in use\n");
+		ret = -EBUSY;
+		goto fail_request_resource;
+	}
+
+	hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len);
+	if (hcd->regs == NULL) {
+		dev_dbg(&pdev->dev, "error mapping memory\n");
+		ret = -ENXIO;
+		goto fail_ioremap;
+	}
+
+	priv = kmalloc(sizeof(struct ehci_sh_priv), GFP_KERNEL);
+	if (!priv) {
+		dev_dbg(&pdev->dev, "error allocating priv data\n");
+		ret = -ENOMEM;
+		goto fail_alloc;
+	}
+
+	/* These are optional, we don't care if they fail */
+	priv->fclk = clk_get(&pdev->dev, "usb_fck");
+	if (IS_ERR(priv->fclk))
+		priv->fclk = NULL;
+
+	priv->iclk = clk_get(&pdev->dev, "usb_ick");
+	if (IS_ERR(priv->iclk))
+		priv->iclk = NULL;
+
+	clk_enable(priv->fclk);
+	clk_enable(priv->iclk);
+
+	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED);
+	if (ret != 0) {
+		dev_err(&pdev->dev, "Failed to add hcd");
+		goto fail_add_hcd;
+	}
+
+	priv->hcd = hcd;
+	platform_set_drvdata(pdev, priv);
+
+	return ret;
+
+fail_add_hcd:
+	clk_disable(priv->iclk);
+	clk_disable(priv->fclk);
+
+	clk_put(priv->iclk);
+	clk_put(priv->fclk);
+
+	kfree(priv);
+fail_alloc:
+	iounmap(hcd->regs);
+fail_ioremap:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+fail_request_resource:
+	usb_put_hcd(hcd);
+fail_create_hcd:
+	dev_err(&pdev->dev, "init %s fail, %d\n", dev_name(&pdev->dev), ret);
+
+	return ret;
+}
+
+static int __exit ehci_hcd_sh_remove(struct platform_device *pdev)
+{
+	struct ehci_sh_priv *priv = platform_get_drvdata(pdev);
+	struct usb_hcd *hcd = priv->hcd;
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+	platform_set_drvdata(pdev, NULL);
+
+	clk_disable(priv->fclk);
+	clk_disable(priv->iclk);
+
+	clk_put(priv->fclk);
+	clk_put(priv->iclk);
+
+	kfree(priv);
+
+	return 0;
+}
+
+static void ehci_hcd_sh_shutdown(struct platform_device *pdev)
+{
+	struct ehci_sh_priv *priv = platform_get_drvdata(pdev);
+	struct usb_hcd *hcd = priv->hcd;
+
+	if (hcd->driver->shutdown)
+		hcd->driver->shutdown(hcd);
+}
+
+static struct platform_driver ehci_hcd_sh_driver = {
+	.probe		= ehci_hcd_sh_probe,
+	.remove		= __exit_p(ehci_hcd_sh_remove),
+	.shutdown	= ehci_hcd_sh_shutdown,
+	.driver		= {
+		.name	= "sh_ehci",
+		.owner	= THIS_MODULE,
+	},
+};
+
+MODULE_ALIAS("platform:sh_ehci");
diff --git a/drivers/usb/host/ehci-spear.c b/drivers/usb/host/ehci-spear.c
new file mode 100644
index 00000000000..75c00873443
--- /dev/null
+++ b/drivers/usb/host/ehci-spear.c
@@ -0,0 +1,212 @@
+/*
+* Driver for EHCI HCD on SPEAR SOC
+*
+* Copyright (C) 2010 ST Micro Electronics,
+* Deepak Sikri <deepak.sikri@st.com>
+*
+* Based on various ehci-*.c drivers
+*
+* This file is subject to the terms and conditions of the GNU General Public
+* License. See the file COPYING in the main directory of this archive for
+* more details.
+*/
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+
+struct spear_ehci {
+	struct ehci_hcd ehci;
+	struct clk *clk;
+};
+
+#define to_spear_ehci(hcd)	(struct spear_ehci *)hcd_to_ehci(hcd)
+
+static void spear_start_ehci(struct spear_ehci *ehci)
+{
+	clk_enable(ehci->clk);
+}
+
+static void spear_stop_ehci(struct spear_ehci *ehci)
+{
+	clk_disable(ehci->clk);
+}
+
+static int ehci_spear_setup(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int retval = 0;
+
+	/* registers start at offset 0x0 */
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs + HC_LENGTH(ehci_readl(ehci,
+				&ehci->caps->hc_capbase));
+	/* cache this readonly data; minimize chip reads */
+	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+	retval = ehci_halt(ehci);
+	if (retval)
+		return retval;
+
+	retval = ehci_init(hcd);
+	if (retval)
+		return retval;
+
+	ehci_reset(ehci);
+	ehci_port_power(ehci, 0);
+
+	return retval;
+}
+
+static const struct hc_driver ehci_spear_hc_driver = {
+	.description			= hcd_name,
+	.product_desc			= "SPEAr EHCI",
+	.hcd_priv_size			= sizeof(struct spear_ehci),
+
+	/* generic hardware linkage */
+	.irq				= ehci_irq,
+	.flags				= HCD_MEMORY | HCD_USB2,
+
+	/* basic lifecycle operations */
+	.reset				= ehci_spear_setup,
+	.start				= ehci_run,
+	.stop				= ehci_stop,
+	.shutdown			= ehci_shutdown,
+
+	/* managing i/o requests and associated device resources */
+	.urb_enqueue			= ehci_urb_enqueue,
+	.urb_dequeue			= ehci_urb_dequeue,
+	.endpoint_disable		= ehci_endpoint_disable,
+	.endpoint_reset			= ehci_endpoint_reset,
+
+	/* scheduling support */
+	.get_frame_number		= ehci_get_frame,
+
+	/* root hub support */
+	.hub_status_data		= ehci_hub_status_data,
+	.hub_control			= ehci_hub_control,
+	.bus_suspend			= ehci_bus_suspend,
+	.bus_resume			= ehci_bus_resume,
+	.relinquish_port		= ehci_relinquish_port,
+	.port_handed_over		= ehci_port_handed_over,
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
+};
+
+static int spear_ehci_hcd_drv_probe(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd ;
+	struct spear_ehci *ehci;
+	struct resource *res;
+	struct clk *usbh_clk;
+	const struct hc_driver *driver = &ehci_spear_hc_driver;
+	int *pdata = pdev->dev.platform_data;
+	int irq, retval;
+	char clk_name[20] = "usbh_clk";
+
+	if (pdata == NULL)
+		return -EFAULT;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		retval = irq;
+		goto fail_irq_get;
+	}
+
+	if (*pdata >= 0)
+		sprintf(clk_name, "usbh.%01d_clk", *pdata);
+
+	usbh_clk = clk_get(NULL, clk_name);
+	if (IS_ERR(usbh_clk)) {
+		dev_err(&pdev->dev, "Error getting interface clock\n");
+		retval = PTR_ERR(usbh_clk);
+		goto fail_get_usbh_clk;
+	}
+
+	hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
+	if (!hcd) {
+		retval = -ENOMEM;
+		goto fail_create_hcd;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		retval = -ENODEV;
+		goto fail_request_resource;
+	}
+
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+				driver->description)) {
+		retval = -EBUSY;
+		goto fail_request_resource;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (hcd->regs == NULL) {
+		dev_dbg(&pdev->dev, "error mapping memory\n");
+		retval = -ENOMEM;
+		goto fail_ioremap;
+	}
+
+	ehci = (struct spear_ehci *)hcd_to_ehci(hcd);
+	ehci->clk = usbh_clk;
+
+	spear_start_ehci(ehci);
+	retval = usb_add_hcd(hcd, irq, IRQF_SHARED | IRQF_DISABLED);
+	if (retval)
+		goto fail_add_hcd;
+
+	return retval;
+
+fail_add_hcd:
+	spear_stop_ehci(ehci);
+	iounmap(hcd->regs);
+fail_ioremap:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+fail_request_resource:
+	usb_put_hcd(hcd);
+fail_create_hcd:
+	clk_put(usbh_clk);
+fail_get_usbh_clk:
+fail_irq_get:
+	dev_err(&pdev->dev, "init fail, %d\n", retval);
+
+	return retval ;
+}
+
+static int spear_ehci_hcd_drv_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+	struct spear_ehci *ehci_p = to_spear_ehci(hcd);
+
+	if (!hcd)
+		return 0;
+	if (in_interrupt())
+		BUG();
+	usb_remove_hcd(hcd);
+
+	if (ehci_p->clk)
+		spear_stop_ehci(ehci_p);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+
+	if (ehci_p->clk)
+		clk_put(ehci_p->clk);
+
+	return 0;
+}
+
+static struct platform_driver spear_ehci_hcd_driver = {
+	.probe		= spear_ehci_hcd_drv_probe,
+	.remove		= spear_ehci_hcd_drv_remove,
+	.shutdown	= usb_hcd_platform_shutdown,
+	.driver		= {
+		.name = "spear-ehci",
+		.bus = &platform_bus_type
+	}
+};
+
+MODULE_ALIAS("platform:spear-ehci");
diff --git a/drivers/usb/host/ehci-vt8500.c b/drivers/usb/host/ehci-vt8500.c
new file mode 100644
index 00000000000..20168062035
--- /dev/null
+++ b/drivers/usb/host/ehci-vt8500.c
@@ -0,0 +1,172 @@
+/*
+ * drivers/usb/host/ehci-vt8500.c
+ *
+ * Copyright (C) 2010 Alexey Charkov <alchark@gmail.com>
+ *
+ * Based on ehci-au1xxx.c
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/platform_device.h>
+
+static int ehci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int rc = 0;
+
+	if (!udev->parent) /* udev is root hub itself, impossible */
+		rc = -1;
+	/* we only support lpm device connected to root hub yet */
+	if (ehci->has_lpm && !udev->parent->parent) {
+		rc = ehci_lpm_set_da(ehci, udev->devnum, udev->portnum);
+		if (!rc)
+			rc = ehci_lpm_check(ehci, udev->portnum);
+	}
+	return rc;
+}
+
+static const struct hc_driver vt8500_ehci_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "VT8500 EHCI",
+	.hcd_priv_size		= sizeof(struct ehci_hcd),
+
+	/*
+	 * generic hardware linkage
+	 */
+	.irq			= ehci_irq,
+	.flags			= HCD_MEMORY | HCD_USB2,
+
+	/*
+	 * basic lifecycle operations
+	 */
+	.reset			= ehci_init,
+	.start			= ehci_run,
+	.stop			= ehci_stop,
+	.shutdown		= ehci_shutdown,
+
+	/*
+	 * managing i/o requests and associated device resources
+	 */
+	.urb_enqueue		= ehci_urb_enqueue,
+	.urb_dequeue		= ehci_urb_dequeue,
+	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
+
+	/*
+	 * scheduling support
+	 */
+	.get_frame_number	= ehci_get_frame,
+
+	/*
+	 * root hub support
+	 */
+	.hub_status_data	= ehci_hub_status_data,
+	.hub_control		= ehci_hub_control,
+	.bus_suspend		= ehci_bus_suspend,
+	.bus_resume		= ehci_bus_resume,
+	.relinquish_port	= ehci_relinquish_port,
+	.port_handed_over	= ehci_port_handed_over,
+
+	/*
+	 * call back when device connected and addressed
+	 */
+	.update_device =	ehci_update_device,
+
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
+};
+
+static int vt8500_ehci_drv_probe(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd;
+	struct ehci_hcd *ehci;
+	struct resource *res;
+	int ret;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	if (pdev->resource[1].flags != IORESOURCE_IRQ) {
+		pr_debug("resource[1] is not IORESOURCE_IRQ");
+		return -ENOMEM;
+	}
+	hcd = usb_create_hcd(&vt8500_ehci_hc_driver, &pdev->dev, "VT8500");
+	if (!hcd)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = resource_size(res);
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
+		pr_debug("request_mem_region failed");
+		ret = -EBUSY;
+		goto err1;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (!hcd->regs) {
+		pr_debug("ioremap failed");
+		ret = -ENOMEM;
+		goto err2;
+	}
+
+	ehci = hcd_to_ehci(hcd);
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase));
+
+	dbg_hcs_params(ehci, "reset");
+	dbg_hcc_params(ehci, "reset");
+
+	/* cache this readonly data; minimize chip reads */
+	ehci->hcs_params = readl(&ehci->caps->hcs_params);
+
+	ehci_port_power(ehci, 1);
+
+	ret = usb_add_hcd(hcd, pdev->resource[1].start,
+			  IRQF_DISABLED | IRQF_SHARED);
+	if (ret == 0) {
+		platform_set_drvdata(pdev, hcd);
+		return ret;
+	}
+
+	iounmap(hcd->regs);
+err2:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+	usb_put_hcd(hcd);
+	return ret;
+}
+
+static int vt8500_ehci_drv_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver vt8500_ehci_driver = {
+	.probe		= vt8500_ehci_drv_probe,
+	.remove		= vt8500_ehci_drv_remove,
+	.shutdown	= usb_hcd_platform_shutdown,
+	.driver = {
+		.name	= "vt8500-ehci",
+		.owner	= THIS_MODULE,
+	}
+};
+
+MODULE_ALIAS("platform:vt8500-ehci");
diff --git a/drivers/usb/host/ehci-w90x900.c b/drivers/usb/host/ehci-w90x900.c
index cfa21ea20f8..6bc35809a5c 100644
--- a/drivers/usb/host/ehci-w90x900.c
+++ b/drivers/usb/host/ehci-w90x900.c
@@ -130,6 +130,7 @@ static const struct hc_driver ehci_w90x900_hc_driver = {
 	.urb_enqueue = ehci_urb_enqueue,
 	.urb_dequeue = ehci_urb_dequeue,
 	.endpoint_disable = ehci_endpoint_disable,
+	.endpoint_reset = ehci_endpoint_reset,
 
 	/*
 	 * scheduling support
@@ -147,6 +148,8 @@ static const struct hc_driver ehci_w90x900_hc_driver = {
 #endif
 	.relinquish_port	= ehci_relinquish_port,
 	.port_handed_over	= ehci_port_handed_over,
+
+	.clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
 };
 
 static int __devinit ehci_w90x900_probe(struct platform_device *pdev)
diff --git a/drivers/usb/host/ehci-xilinx-of.c b/drivers/usb/host/ehci-xilinx-of.c
index 6c8076ad821..e8f4f36fdf0 100644
--- a/drivers/usb/host/ehci-xilinx-of.c
+++ b/drivers/usb/host/ehci-xilinx-of.c
@@ -117,6 +117,7 @@ static const struct hc_driver ehci_xilinx_of_hc_driver = {
 	.urb_enqueue		= ehci_urb_enqueue,
 	.urb_dequeue		= ehci_urb_dequeue,
 	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
 
 	/*
 	 * scheduling support
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index ba8eab366b8..799ac16a54b 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -131,6 +131,7 @@ struct ehci_hcd {			/* one per controller */
 	unsigned		has_amcc_usb23:1;
 	unsigned		need_io_watchdog:1;
 	unsigned		broken_periodic:1;
+	unsigned		amd_l1_fix:1;
 	unsigned		fs_i_thresh:1;	/* Intel iso scheduling */
 	unsigned		use_dummy_qh:1;	/* AMD Frame List table quirk*/
 
diff --git a/drivers/usb/host/ohci-cns3xxx.c b/drivers/usb/host/ohci-cns3xxx.c
new file mode 100644
index 00000000000..f05ef87e934
--- /dev/null
+++ b/drivers/usb/host/ohci-cns3xxx.c
@@ -0,0 +1,165 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/atomic.h>
+#include <mach/cns3xxx.h>
+#include <mach/pm.h>
+
+static int __devinit
+cns3xxx_ohci_start(struct usb_hcd *hcd)
+{
+	struct ohci_hcd	*ohci = hcd_to_ohci(hcd);
+	int ret;
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 *
+	 * Set USB AHB INCR length to 16
+	 */
+	if (atomic_inc_return(&usb_pwr_ref) == 1) {
+		cns3xxx_pwr_power_up(1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB);
+		cns3xxx_pwr_clk_en(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+		cns3xxx_pwr_soft_rst(1 << PM_SOFT_RST_REG_OFFST_USB_HOST);
+		__raw_writel((__raw_readl(MISC_CHIP_CONFIG_REG) | (0X2 << 24)),
+			MISC_CHIP_CONFIG_REG);
+	}
+
+	ret = ohci_init(ohci);
+	if (ret < 0)
+		return ret;
+
+	ohci->num_ports = 1;
+
+	ret = ohci_run(ohci);
+	if (ret < 0) {
+		err("can't start %s", hcd->self.bus_name);
+		ohci_stop(hcd);
+		return ret;
+	}
+	return 0;
+}
+
+static const struct hc_driver cns3xxx_ohci_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "CNS3XXX OHCI Host controller",
+	.hcd_priv_size		= sizeof(struct ohci_hcd),
+	.irq			= ohci_irq,
+	.flags			= HCD_USB11 | HCD_MEMORY,
+	.start			= cns3xxx_ohci_start,
+	.stop			= ohci_stop,
+	.shutdown		= ohci_shutdown,
+	.urb_enqueue		= ohci_urb_enqueue,
+	.urb_dequeue		= ohci_urb_dequeue,
+	.endpoint_disable	= ohci_endpoint_disable,
+	.get_frame_number	= ohci_get_frame,
+	.hub_status_data	= ohci_hub_status_data,
+	.hub_control		= ohci_hub_control,
+#ifdef CONFIG_PM
+	.bus_suspend		= ohci_bus_suspend,
+	.bus_resume		= ohci_bus_resume,
+#endif
+	.start_port_reset	= ohci_start_port_reset,
+};
+
+static int cns3xxx_ohci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct usb_hcd *hcd;
+	const struct hc_driver *driver = &cns3xxx_ohci_hc_driver;
+	struct resource *res;
+	int irq;
+	int retval;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no IRQ.\n");
+		return -ENODEV;
+	}
+	irq = res->start;
+
+	hcd = usb_create_hcd(driver, dev, dev_name(dev));
+	if (!hcd)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no register addr.\n");
+		retval = -ENODEV;
+		goto err1;
+	}
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = res->end - res->start + 1;
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+			driver->description)) {
+		dev_dbg(dev, "controller already in use\n");
+		retval = -EBUSY;
+		goto err1;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (!hcd->regs) {
+		dev_dbg(dev, "error mapping memory\n");
+		retval = -EFAULT;
+		goto err2;
+	}
+
+	ohci_hcd_init(hcd_to_ohci(hcd));
+
+	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (retval == 0)
+		return retval;
+
+	iounmap(hcd->regs);
+err2:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+	usb_put_hcd(hcd);
+	return retval;
+}
+
+static int cns3xxx_ohci_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 */
+	if (atomic_dec_return(&usb_pwr_ref) == 0)
+		cns3xxx_pwr_clk_dis(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+
+	usb_put_hcd(hcd);
+
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+MODULE_ALIAS("platform:cns3xxx-ohci");
+
+static struct platform_driver ohci_hcd_cns3xxx_driver = {
+	.probe = cns3xxx_ohci_probe,
+	.remove = cns3xxx_ohci_remove,
+	.driver = {
+		.name = "cns3xxx-ohci",
+	},
+};
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 5179acb7aa2..759a12ff804 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -901,7 +901,8 @@ static void ohci_stop (struct usb_hcd *hcd)
 
 	ohci_dump (ohci, 1);
 
-	flush_scheduled_work();
+	if (quirk_nec(ohci))
+		flush_work_sync(&ohci->nec_work);
 
 	ohci_usb_reset (ohci);
 	ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
@@ -1081,6 +1082,11 @@ MODULE_LICENSE ("GPL");
 #define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
 #endif
 
+#ifdef CONFIG_PLAT_SPEAR
+#include "ohci-spear.c"
+#define PLATFORM_DRIVER		spear_ohci_hcd_driver
+#endif
+
 #ifdef CONFIG_PPC_PS3
 #include "ohci-ps3.c"
 #define PS3_SYSTEM_BUS_DRIVER	ps3_ohci_driver
@@ -1111,6 +1117,11 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ohci_octeon_driver
 #endif
 
+#ifdef CONFIG_USB_CNS3XXX_OHCI
+#include "ohci-cns3xxx.c"
+#define PLATFORM_DRIVER		ohci_hcd_cns3xxx_driver
+#endif
+
 #if	!defined(PCI_DRIVER) &&		\
 	!defined(PLATFORM_DRIVER) &&	\
 	!defined(OMAP1_PLATFORM_DRIVER) &&	\
diff --git a/drivers/usb/host/ohci-omap3.c b/drivers/usb/host/ohci-omap3.c
index 2cc8a504b18..a37d5993e4e 100644
--- a/drivers/usb/host/ohci-omap3.c
+++ b/drivers/usb/host/ohci-omap3.c
@@ -648,7 +648,7 @@ static int __devinit ohci_hcd_omap3_probe(struct platform_device *pdev)
 
 	ret = omap3_start_ohci(omap, hcd);
 	if (ret) {
-		dev_dbg(&pdev->dev, "failed to start ehci\n");
+		dev_dbg(&pdev->dev, "failed to start ohci\n");
 		goto err_start;
 	}
 
diff --git a/drivers/usb/host/ohci-sh.c b/drivers/usb/host/ohci-sh.c
index 0b35d22cc70..f47867ff78c 100644
--- a/drivers/usb/host/ohci-sh.c
+++ b/drivers/usb/host/ohci-sh.c
@@ -109,7 +109,7 @@ static int ohci_hcd_sh_probe(struct platform_device *pdev)
 	hcd->regs = (void __iomem *)res->start;
 	hcd->rsrc_start = res->start;
 	hcd->rsrc_len = resource_size(res);
-	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
+	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED);
 	if (ret != 0) {
 		err("Failed to add hcd");
 		usb_put_hcd(hcd);
diff --git a/drivers/usb/host/ohci-spear.c b/drivers/usb/host/ohci-spear.c
new file mode 100644
index 00000000000..4fd4bea9ac7
--- /dev/null
+++ b/drivers/usb/host/ohci-spear.c
@@ -0,0 +1,240 @@
+/*
+* OHCI HCD (Host Controller Driver) for USB.
+*
+* Copyright (C) 2010 ST Microelectronics.
+* Deepak Sikri<deepak.sikri@st.com>
+*
+* Based on various ohci-*.c drivers
+*
+* This file is licensed under the terms of the GNU General Public
+* License version 2. This program is licensed "as is" without any
+* warranty of any kind, whether express or implied.
+*/
+
+#include <linux/signal.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+
+struct spear_ohci {
+	struct ohci_hcd ohci;
+	struct clk *clk;
+};
+
+#define to_spear_ohci(hcd)	(struct spear_ohci *)hcd_to_ohci(hcd)
+
+static void spear_start_ohci(struct spear_ohci *ohci)
+{
+	clk_enable(ohci->clk);
+}
+
+static void spear_stop_ohci(struct spear_ohci *ohci)
+{
+	clk_disable(ohci->clk);
+}
+
+static int __devinit ohci_spear_start(struct usb_hcd *hcd)
+{
+	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+	int ret;
+
+	ret = ohci_init(ohci);
+	if (ret < 0)
+		return ret;
+	ohci->regs = hcd->regs;
+
+	ret = ohci_run(ohci);
+	if (ret < 0) {
+		dev_err(hcd->self.controller, "can't start\n");
+		ohci_stop(hcd);
+		return ret;
+	}
+
+	create_debug_files(ohci);
+
+#ifdef DEBUG
+	ohci_dump(ohci, 1);
+#endif
+	return 0;
+}
+
+static const struct hc_driver ohci_spear_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "SPEAr OHCI",
+	.hcd_priv_size		= sizeof(struct spear_ohci),
+
+	/* generic hardware linkage */
+	.irq			= ohci_irq,
+	.flags			= HCD_USB11 | HCD_MEMORY,
+
+	/* basic lifecycle operations */
+	.start			= ohci_spear_start,
+	.stop			= ohci_stop,
+	.shutdown		= ohci_shutdown,
+#ifdef	CONFIG_PM
+	.bus_suspend		= ohci_bus_suspend,
+	.bus_resume		= ohci_bus_resume,
+#endif
+
+	/* managing i/o requests and associated device resources */
+	.urb_enqueue		= ohci_urb_enqueue,
+	.urb_dequeue		= ohci_urb_dequeue,
+	.endpoint_disable	= ohci_endpoint_disable,
+
+	/* scheduling support */
+	.get_frame_number	= ohci_get_frame,
+
+	/* root hub support */
+	.hub_status_data	= ohci_hub_status_data,
+	.hub_control		= ohci_hub_control,
+
+	.start_port_reset	= ohci_start_port_reset,
+};
+
+static int spear_ohci_hcd_drv_probe(struct platform_device *pdev)
+{
+	const struct hc_driver *driver = &ohci_spear_hc_driver;
+	struct usb_hcd *hcd = NULL;
+	struct clk *usbh_clk;
+	struct spear_ohci *ohci_p;
+	struct resource *res;
+	int retval, irq;
+	int *pdata = pdev->dev.platform_data;
+	char clk_name[20] = "usbh_clk";
+
+	if (pdata == NULL)
+		return -EFAULT;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		retval = irq;
+		goto fail_irq_get;
+	}
+
+	if (*pdata >= 0)
+		sprintf(clk_name, "usbh.%01d_clk", *pdata);
+
+	usbh_clk = clk_get(NULL, clk_name);
+	if (IS_ERR(usbh_clk)) {
+		dev_err(&pdev->dev, "Error getting interface clock\n");
+		retval = PTR_ERR(usbh_clk);
+		goto fail_get_usbh_clk;
+	}
+
+	hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
+	if (!hcd) {
+		retval = -ENOMEM;
+		goto fail_create_hcd;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		retval = -ENODEV;
+		goto fail_request_resource;
+	}
+
+	hcd->rsrc_start = pdev->resource[0].start;
+	hcd->rsrc_len = resource_size(res);
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
+		dev_dbg(&pdev->dev, "request_mem_region failed\n");
+		retval = -EBUSY;
+		goto fail_request_resource;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (!hcd->regs) {
+		dev_dbg(&pdev->dev, "ioremap failed\n");
+		retval = -ENOMEM;
+		goto fail_ioremap;
+	}
+
+	ohci_p = (struct spear_ohci *)hcd_to_ohci(hcd);
+	ohci_p->clk = usbh_clk;
+	spear_start_ohci(ohci_p);
+	ohci_hcd_init(hcd_to_ohci(hcd));
+
+	retval = usb_add_hcd(hcd, platform_get_irq(pdev, 0), IRQF_DISABLED);
+	if (retval == 0)
+		return retval;
+
+	spear_stop_ohci(ohci_p);
+	iounmap(hcd->regs);
+fail_ioremap:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+fail_request_resource:
+	usb_put_hcd(hcd);
+fail_create_hcd:
+	clk_put(usbh_clk);
+fail_get_usbh_clk:
+fail_irq_get:
+	dev_err(&pdev->dev, "init fail, %d\n", retval);
+
+	return retval;
+}
+
+static int spear_ohci_hcd_drv_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+	struct spear_ohci *ohci_p = to_spear_ohci(hcd);
+
+	usb_remove_hcd(hcd);
+	if (ohci_p->clk)
+		spear_stop_ohci(ohci_p);
+
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+	usb_put_hcd(hcd);
+
+	if (ohci_p->clk)
+		clk_put(ohci_p->clk);
+	platform_set_drvdata(pdev, NULL);
+	return 0;
+}
+
+#if defined(CONFIG_PM)
+static int spear_ohci_hcd_drv_suspend(struct platform_device *dev,
+		pm_message_t message)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(dev);
+	struct ohci_hcd	*ohci = hcd_to_ohci(hcd);
+	struct spear_ohci *ohci_p = to_spear_ohci(hcd);
+
+	if (time_before(jiffies, ohci->next_statechange))
+		msleep(5);
+	ohci->next_statechange = jiffies;
+
+	spear_stop_ohci(ohci_p);
+	ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
+	return 0;
+}
+
+static int spear_ohci_hcd_drv_resume(struct platform_device *dev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(dev);
+	struct ohci_hcd	*ohci = hcd_to_ohci(hcd);
+	struct spear_ohci *ohci_p = to_spear_ohci(hcd);
+
+	if (time_before(jiffies, ohci->next_statechange))
+		msleep(5);
+	ohci->next_statechange = jiffies;
+
+	spear_start_ohci(ohci_p);
+	ohci_finish_controller_resume(hcd);
+	return 0;
+}
+#endif
+
+/* Driver definition to register with the platform bus */
+static struct platform_driver spear_ohci_hcd_driver = {
+	.probe =	spear_ohci_hcd_drv_probe,
+	.remove =	spear_ohci_hcd_drv_remove,
+#ifdef CONFIG_PM
+	.suspend =	spear_ohci_hcd_drv_suspend,
+	.resume =	spear_ohci_hcd_drv_resume,
+#endif
+	.driver = {
+		.owner = THIS_MODULE,
+		.name = "spear-ohci",
+	},
+};
+
+MODULE_ALIAS("platform:spear-ohci");
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index f52d04db28f..cee867829ec 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -569,7 +569,7 @@ static int uhci_init(struct usb_hcd *hcd)
  */
 static void uhci_shutdown(struct pci_dev *pdev)
 {
-	struct usb_hcd *hcd = (struct usb_hcd *) pci_get_drvdata(pdev);
+	struct usb_hcd *hcd = pci_get_drvdata(pdev);
 
 	uhci_hc_died(hcd_to_uhci(hcd));
 }
diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index 2090b45eb60..af77abb5c68 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -29,7 +29,7 @@ static void uhci_set_next_interrupt(struct uhci_hcd *uhci)
 {
 	if (uhci->is_stopped)
 		mod_timer(&uhci_to_hcd(uhci)->rh_timer, jiffies);
-	uhci->term_td->status |= cpu_to_le32(TD_CTRL_IOC); 
+	uhci->term_td->status |= cpu_to_le32(TD_CTRL_IOC);
 }
 
 static inline void uhci_clear_next_interrupt(struct uhci_hcd *uhci)
@@ -195,7 +195,9 @@ static inline void uhci_remove_td_from_frame_list(struct uhci_hcd *uhci,
 		} else {
 			struct uhci_td *ntd;
 
-			ntd = list_entry(td->fl_list.next, struct uhci_td, fl_list);
+			ntd = list_entry(td->fl_list.next,
+					 struct uhci_td,
+					 fl_list);
 			uhci->frame[td->frame] = LINK_TO_TD(ntd);
 			uhci->frame_cpu[td->frame] = ntd;
 		}
@@ -728,7 +730,7 @@ static inline struct urb_priv *uhci_alloc_urb_priv(struct uhci_hcd *uhci,
 
 	urbp->urb = urb;
 	urb->hcpriv = urbp;
-	
+
 	INIT_LIST_HEAD(&urbp->node);
 	INIT_LIST_HEAD(&urbp->td_list);
 
@@ -846,7 +848,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb,
 
 		/* Alternate Data0/1 (start with Data1) */
 		destination ^= TD_TOKEN_TOGGLE;
-	
+
 		uhci_add_td_to_urbp(td, urbp);
 		uhci_fill_td(td, status, destination | uhci_explen(pktsze),
 				data);
@@ -857,7 +859,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb,
 	}
 
 	/*
-	 * Build the final TD for control status 
+	 * Build the final TD for control status
 	 */
 	td = uhci_alloc_td(uhci);
 	if (!td)
diff --git a/drivers/usb/host/whci/hcd.c b/drivers/usb/host/whci/hcd.c
index 72b6892fda6..9546f6cd01f 100644
--- a/drivers/usb/host/whci/hcd.c
+++ b/drivers/usb/host/whci/hcd.c
@@ -356,7 +356,7 @@ static void __exit whci_hc_driver_exit(void)
 module_exit(whci_hc_driver_exit);
 
 /* PCI device ID's that we handle (so it gets loaded) */
-static struct pci_device_id whci_hcd_id_table[] = {
+static struct pci_device_id __used whci_hcd_id_table[] = {
 	{ PCI_DEVICE_CLASS(PCI_CLASS_WIRELESS_WHCI, ~0) },
 	{ /* empty last entry */ }
 };