xHCI: Kick khubd when USB3 resume really completes.

xHCI roothubs go through slightly different port state machines when
either a device initiates a remote wakeup and signals resume, or when
the host initiates a resume.

According to section 4.19.1.2.13 of the xHCI 1.0 spec, on host-initiated
resume, the xHC port state machine automatically goes through the U3Exit
state into the U0 state, setting the port link state change (PLC) bit in
the process.

When a device initiates resume, the xHCI port state machine goes into
the "Resume" state and sets the PLC bit.  Then the xHCI driver writes U0
into the port link state register to transition the port to U0 from the
Resume state.

We can't be sure the device is actually in the U0 state until we receive
the next port status change event with the PLC bit set.  We really don't
want khubd to be polling the roothub port status bits until the device
is really in U0.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>

1 files changed, 17 insertions, 12 deletions

diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index b62037bff68..ca38483c9f5 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1321,20 +1321,16 @@ static void handle_port_status(struct xhci_hcd *xhci,
 		}
 
 		if (DEV_SUPERSPEED(temp)) {
-			xhci_dbg(xhci, "resume SS port %d\n", port_id);
+			xhci_dbg(xhci, "remote wake SS port %d\n", port_id);
+			xhci_test_and_clear_bit(xhci, port_array,
+					faked_port_index, PORT_PLC);
 			xhci_set_link_state(xhci, port_array, faked_port_index,
 						XDEV_U0);
-			slot_id = xhci_find_slot_id_by_port(hcd, xhci,
-					faked_port_index + 1);
-			if (!slot_id) {
-				xhci_dbg(xhci, "slot_id is zero\n");
-				goto cleanup;
-			}
-			xhci_ring_device(xhci, slot_id);
-			xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
-			/* Clear PORT_PLC */
-			xhci_test_and_clear_bit(xhci, port_array,
-						faked_port_index, PORT_PLC);
+			/* Need to wait until the next link state change
+			 * indicates the device is actually in U0.
+			 */
+			bogus_port_status = true;
+			goto cleanup;
 		} else {
 			xhci_dbg(xhci, "resume HS port %d\n", port_id);
 			bus_state->resume_done[faked_port_index] = jiffies +
@@ -1345,6 +1341,15 @@ static void handle_port_status(struct xhci_hcd *xhci,
 		}
 	}
 
+	if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_U0 &&
+			DEV_SUPERSPEED(temp)) {
+		xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
+		slot_id = xhci_find_slot_id_by_port(hcd, xhci,
+				faked_port_index + 1);
+		if (slot_id && xhci->devs[slot_id])
+			xhci_ring_device(xhci, slot_id);
+	}
+
 	if (hcd->speed != HCD_USB3)
 		xhci_test_and_clear_bit(xhci, port_array, faked_port_index,
 					PORT_PLC);