Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/jkirsher/net-next-2.6

19 files changed, 590 insertions, 320 deletions

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7ce3dd01d6e..925c25c295f 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2109,6 +2109,7 @@ config E1000
 config E1000E
 	tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
 	depends on PCI && (!SPARC32 || BROKEN)
+	select CRC32
 	---help---
 	  This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
 	  ethernet family of adapters. For PCI or PCI-X e1000 adapters,
diff --git a/drivers/net/igb/e1000_defines.h b/drivers/net/igb/e1000_defines.h
index ff46c91520a..92e11da2574 100644
--- a/drivers/net/igb/e1000_defines.h
+++ b/drivers/net/igb/e1000_defines.h
@@ -110,6 +110,7 @@
 /* Management Control */
 #define E1000_MANC_SMBUS_EN      0x00000001 /* SMBus Enabled - RO */
 #define E1000_MANC_ASF_EN        0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_EN_BMC2OS     0x10000000 /* OSBMC is Enabled or not */
 /* Enable Neighbor Discovery Filtering */
 #define E1000_MANC_RCV_TCO_EN    0x00020000 /* Receive TCO Packets Enabled */
 #define E1000_MANC_BLK_PHY_RST_ON_IDE   0x00040000 /* Block phy resets */
diff --git a/drivers/net/igb/e1000_hw.h b/drivers/net/igb/e1000_hw.h
index 281324e8598..eec9ed73558 100644
--- a/drivers/net/igb/e1000_hw.h
+++ b/drivers/net/igb/e1000_hw.h
@@ -248,6 +248,10 @@ struct e1000_hw_stats {
 	u64 scvpc;
 	u64 hrmpc;
 	u64 doosync;
+	u64 o2bgptc;
+	u64 o2bspc;
+	u64 b2ospc;
+	u64 b2ogprc;
 };
 
 struct e1000_phy_stats {
diff --git a/drivers/net/igb/e1000_regs.h b/drivers/net/igb/e1000_regs.h
index 3a6f8471aea..61713548c02 100644
--- a/drivers/net/igb/e1000_regs.h
+++ b/drivers/net/igb/e1000_regs.h
@@ -328,4 +328,11 @@
 
 /* DMA Coalescing registers */
 #define E1000_PCIEMISC          0x05BB8 /* PCIE misc config register */
+
+/* OS2BMC Registers */
+#define E1000_B2OSPC    0x08FE0 /* BMC2OS packets sent by BMC */
+#define E1000_B2OGPRC   0x04158 /* BMC2OS packets received by host */
+#define E1000_O2BGPTC   0x08FE4 /* OS2BMC packets received by BMC */
+#define E1000_O2BSPC    0x0415C /* OS2BMC packets transmitted by host */
+
 #endif
diff --git a/drivers/net/igb/igb_ethtool.c b/drivers/net/igb/igb_ethtool.c
index 61f7849cb5a..78d420b4b2d 100644
--- a/drivers/net/igb/igb_ethtool.c
+++ b/drivers/net/igb/igb_ethtool.c
@@ -86,6 +86,10 @@ static const struct igb_stats igb_gstrings_stats[] = {
 	IGB_STAT("tx_smbus", stats.mgptc),
 	IGB_STAT("rx_smbus", stats.mgprc),
 	IGB_STAT("dropped_smbus", stats.mgpdc),
+	IGB_STAT("os2bmc_rx_by_bmc", stats.o2bgptc),
+	IGB_STAT("os2bmc_tx_by_bmc", stats.b2ospc),
+	IGB_STAT("os2bmc_tx_by_host", stats.o2bspc),
+	IGB_STAT("os2bmc_rx_by_host", stats.b2ogprc),
 };
 
 #define IGB_NETDEV_STAT(_net_stat) { \
@@ -603,7 +607,10 @@ static void igb_get_regs(struct net_device *netdev,
 	regs_buff[548] = rd32(E1000_TDFT);
 	regs_buff[549] = rd32(E1000_TDFHS);
 	regs_buff[550] = rd32(E1000_TDFPC);
-
+	regs_buff[551] = adapter->stats.o2bgptc;
+	regs_buff[552] = adapter->stats.b2ospc;
+	regs_buff[553] = adapter->stats.o2bspc;
+	regs_buff[554] = adapter->stats.b2ogprc;
 }
 
 static int igb_get_eeprom_len(struct net_device *netdev)
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index eef380af053..3666b967846 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -4560,6 +4560,15 @@ void igb_update_stats(struct igb_adapter *adapter,
 	adapter->stats.mgptc += rd32(E1000_MGTPTC);
 	adapter->stats.mgprc += rd32(E1000_MGTPRC);
 	adapter->stats.mgpdc += rd32(E1000_MGTPDC);
+
+	/* OS2BMC Stats */
+	reg = rd32(E1000_MANC);
+	if (reg & E1000_MANC_EN_BMC2OS) {
+		adapter->stats.o2bgptc += rd32(E1000_O2BGPTC);
+		adapter->stats.o2bspc += rd32(E1000_O2BSPC);
+		adapter->stats.b2ospc += rd32(E1000_B2OSPC);
+		adapter->stats.b2ogprc += rd32(E1000_B2OGPRC);
+	}
 }
 
 static irqreturn_t igb_msix_other(int irq, void *data)
diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h
index b60b81bc2b1..1e546fc127d 100644
--- a/drivers/net/ixgbe/ixgbe.h
+++ b/drivers/net/ixgbe/ixgbe.h
@@ -552,6 +552,8 @@ extern int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter,
                           struct sk_buff *skb);
 extern int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
                               struct scatterlist *sgl, unsigned int sgc);
+extern int ixgbe_fcoe_ddp_target(struct net_device *netdev, u16 xid,
+				 struct scatterlist *sgl, unsigned int sgc);
 extern int ixgbe_fcoe_ddp_put(struct net_device *netdev, u16 xid);
 extern int ixgbe_fcoe_enable(struct net_device *netdev);
 extern int ixgbe_fcoe_disable(struct net_device *netdev);
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index fc41329399b..ff23907bde0 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -280,10 +280,22 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
 {
 	enum ixgbe_media_type media_type;
 
+	/* Detect if there is a copper PHY attached. */
+	switch (hw->phy.type) {
+	case ixgbe_phy_cu_unknown:
+	case ixgbe_phy_tn:
+	case ixgbe_phy_aq:
+		media_type = ixgbe_media_type_copper;
+		goto out;
+	default:
+		break;
+	}
+
 	/* Media type for I82598 is based on device ID */
 	switch (hw->device_id) {
 	case IXGBE_DEV_ID_82598:
 	case IXGBE_DEV_ID_82598_BX:
+		/* Default device ID is mezzanine card KX/KX4 */
 		media_type = ixgbe_media_type_backplane;
 		break;
 	case IXGBE_DEV_ID_82598AF_DUAL_PORT:
@@ -306,7 +318,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
 		media_type = ixgbe_media_type_unknown;
 		break;
 	}
-
+out:
 	return media_type;
 }
 
@@ -354,7 +366,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 
 	/* Negotiate the fc mode to use */
 	ret_val = ixgbe_fc_autoneg(hw);
-	if (ret_val)
+	if (ret_val == IXGBE_ERR_FLOW_CONTROL)
 		goto out;
 
 	/* Disable any previous flow control settings */
@@ -372,10 +384,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 	 * 2: Tx flow control is enabled (we can send pause frames but
 	 *     we do not support receiving pause frames).
 	 * 3: Both Rx and Tx flow control (symmetric) are enabled.
-	 * other: Invalid.
 #ifdef CONFIG_DCB
 	 * 4: Priority Flow Control is enabled.
 #endif
+	 * other: Invalid.
 	 */
 	switch (hw->fc.current_mode) {
 	case ixgbe_fc_none:
@@ -432,9 +444,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 		reg = (rx_pba_size - hw->fc.low_water) << 6;
 		if (hw->fc.send_xon)
 			reg |= IXGBE_FCRTL_XONE;
+
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg);
 
-		reg = (rx_pba_size - hw->fc.high_water) << 10;
+		reg = (rx_pba_size - hw->fc.high_water) << 6;
 		reg |= IXGBE_FCRTH_FCEN;
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg);
@@ -632,7 +645,7 @@ out:
  *  @hw: pointer to hardware structure
  *  @speed: new link speed
  *  @autoneg: true if auto-negotiation enabled
- *  @autoneg_wait_to_complete: true if waiting is needed to complete
+ *  @autoneg_wait_to_complete: true when waiting for completion is needed
  *
  *  Set the link speed in the AUTOC register and restarts link.
  **/
@@ -671,7 +684,8 @@ static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw,
 		 * ixgbe_hw This will write the AUTOC register based on the new
 		 * stored values
 		 */
-		status = ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
+		status = ixgbe_start_mac_link_82598(hw,
+						    autoneg_wait_to_complete);
 	}
 
 	return status;
@@ -1090,10 +1104,12 @@ static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
 
 	/* Copper PHY must be checked before AUTOC LMS to determine correct
 	 * physical layer because 10GBase-T PHYs use LMS = KX4/KX */
-	if (hw->phy.type == ixgbe_phy_tn ||
-	    hw->phy.type == ixgbe_phy_cu_unknown) {
-		hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
-				     &ext_ability);
+	switch (hw->phy.type) {
+	case ixgbe_phy_tn:
+	case ixgbe_phy_aq:
+	case ixgbe_phy_cu_unknown:
+		hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE,
+		MDIO_MMD_PMAPMD, &ext_ability);
 		if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
 			physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
 		if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
@@ -1101,6 +1117,8 @@ static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
 		if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
 			physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
 		goto out;
+	default:
+		break;
 	}
 
 	switch (autoc & IXGBE_AUTOC_LMS_MASK) {
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c
index 5ef968a10d4..00aeba385a2 100644
--- a/drivers/net/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ixgbe/ixgbe_82599.c
@@ -470,8 +470,6 @@ static void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
  **/
 static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
 {
-	hw_dbg(hw, "ixgbe_flap_tx_laser_multispeed_fiber\n");
-
 	if (hw->mac.autotry_restart) {
 		ixgbe_disable_tx_laser_multispeed_fiber(hw);
 		ixgbe_enable_tx_laser_multispeed_fiber(hw);
@@ -494,17 +492,21 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
                                           bool autoneg_wait_to_complete)
 {
 	s32 status = 0;
-	ixgbe_link_speed phy_link_speed;
+	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
 	ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
 	u32 speedcnt = 0;
 	u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
+	u32 i = 0;
 	bool link_up = false;
 	bool negotiation;
-	int i;
 
 	/* Mask off requested but non-supported speeds */
-	hw->mac.ops.get_link_capabilities(hw, &phy_link_speed, &negotiation);
-	speed &= phy_link_speed;
+	status = hw->mac.ops.get_link_capabilities(hw, &link_speed,
+						   &negotiation);
+	if (status != 0)
+		return status;
+
+	speed &= link_speed;
 
 	/*
 	 * Try each speed one by one, highest priority first.  We do this in
@@ -515,9 +517,12 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 		highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
 
 		/* If we already have link at this speed, just jump out */
-		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status != 0)
+			return status;
 
-		if ((phy_link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
+		if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
 			goto out;
 
 		/* Set the module link speed */
@@ -529,9 +534,9 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 		msleep(40);
 
 		status = ixgbe_setup_mac_link_82599(hw,
-		                               IXGBE_LINK_SPEED_10GB_FULL,
-		                               autoneg,
-		                               autoneg_wait_to_complete);
+						    IXGBE_LINK_SPEED_10GB_FULL,
+						    autoneg,
+						    autoneg_wait_to_complete);
 		if (status != 0)
 			return status;
 
@@ -548,8 +553,11 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 			msleep(100);
 
 			/* If we have link, just jump out */
-			hw->mac.ops.check_link(hw, &phy_link_speed,
-			                       &link_up, false);
+			status = hw->mac.ops.check_link(hw, &link_speed,
+							&link_up, false);
+			if (status != 0)
+				return status;
+
 			if (link_up)
 				goto out;
 		}
@@ -561,9 +569,12 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 			highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
 
 		/* If we already have link at this speed, just jump out */
-		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status != 0)
+			return status;
 
-		if ((phy_link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
+		if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
 			goto out;
 
 		/* Set the module link speed */
@@ -576,9 +587,9 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 		msleep(40);
 
 		status = ixgbe_setup_mac_link_82599(hw,
-		                                      IXGBE_LINK_SPEED_1GB_FULL,
-		                                      autoneg,
-		                                      autoneg_wait_to_complete);
+						    IXGBE_LINK_SPEED_1GB_FULL,
+						    autoneg,
+						    autoneg_wait_to_complete);
 		if (status != 0)
 			return status;
 
@@ -589,7 +600,11 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 		msleep(100);
 
 		/* If we have link, just jump out */
-		hw->mac.ops.check_link(hw, &phy_link_speed, &link_up, false);
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status != 0)
+			return status;
+
 		if (link_up)
 			goto out;
 	}
@@ -632,13 +647,10 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 				     bool autoneg_wait_to_complete)
 {
 	s32 status = 0;
-	ixgbe_link_speed link_speed;
+	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
 	s32 i, j;
 	bool link_up = false;
 	u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
-	struct ixgbe_adapter *adapter = hw->back;
-
-	hw_dbg(hw, "ixgbe_setup_mac_link_smartspeed.\n");
 
 	 /* Set autoneg_advertised value based on input link speed */
 	hw->phy.autoneg_advertised = 0;
@@ -664,7 +676,7 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 	for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) {
 		status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
 						    autoneg_wait_to_complete);
-		if (status)
+		if (status != 0)
 			goto out;
 
 		/*
@@ -677,8 +689,11 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 			mdelay(100);
 
 			/* If we have link, just jump out */
-			hw->mac.ops.check_link(hw, &link_speed,
-			                       &link_up, false);
+			status = hw->mac.ops.check_link(hw, &link_speed,
+							&link_up, false);
+			if (status != 0)
+				goto out;
+
 			if (link_up)
 				goto out;
 		}
@@ -696,7 +711,7 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 	hw->phy.smart_speed_active = true;
 	status = ixgbe_setup_mac_link_82599(hw, speed, autoneg,
 					    autoneg_wait_to_complete);
-	if (status)
+	if (status != 0)
 		goto out;
 
 	/*
@@ -709,8 +724,11 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 		mdelay(100);
 
 		/* If we have link, just jump out */
-		hw->mac.ops.check_link(hw, &link_speed,
-		                       &link_up, false);
+		status = hw->mac.ops.check_link(hw, &link_speed,
+						&link_up, false);
+		if (status != 0)
+			goto out;
+
 		if (link_up)
 			goto out;
 	}
@@ -722,7 +740,7 @@ static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 
 out:
 	if (link_up && (link_speed == IXGBE_LINK_SPEED_1GB_FULL))
-		e_info(hw, "Smartspeed has downgraded the link speed from "
+		hw_dbg(hw, "Smartspeed has downgraded the link speed from "
 		       "the maximum advertised\n");
 	return status;
 }
@@ -754,6 +772,9 @@ static s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
 
 	/* Check to see if speed passed in is supported. */
 	hw->mac.ops.get_link_capabilities(hw, &link_capabilities, &autoneg);
+	if (status != 0)
+		goto out;
+
 	speed &= link_capabilities;
 
 	if (speed == IXGBE_LINK_SPEED_UNKNOWN) {
@@ -883,7 +904,7 @@ static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
 
 	/* PHY ops must be identified and initialized prior to reset */
 
-	/* Init PHY and function pointers, perform SFP setup */
+	/* Identify PHY and related function pointers */
 	status = hw->phy.ops.init(hw);
 
 	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
@@ -895,6 +916,9 @@ static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw)
 		hw->phy.sfp_setup_needed = false;
 	}
 
+	if (status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+		goto reset_hw_out;
+
 	/* Reset PHY */
 	if (hw->phy.reset_disable == false && hw->phy.ops.reset != NULL)
 		hw->phy.ops.reset(hw);
@@ -2051,28 +2075,28 @@ static struct ixgbe_mac_operations mac_ops_82599 = {
 };
 
 static struct ixgbe_eeprom_operations eeprom_ops_82599 = {
-	.init_params            = &ixgbe_init_eeprom_params_generic,
-	.read                   = &ixgbe_read_eerd_generic,
-	.write                  = &ixgbe_write_eeprom_generic,
-	.calc_checksum          = &ixgbe_calc_eeprom_checksum_generic,
-	.validate_checksum      = &ixgbe_validate_eeprom_checksum_generic,
-	.update_checksum        = &ixgbe_update_eeprom_checksum_generic,
+	.init_params		= &ixgbe_init_eeprom_params_generic,
+	.read			= &ixgbe_read_eerd_generic,
+	.write			= &ixgbe_write_eeprom_generic,
+	.calc_checksum		= &ixgbe_calc_eeprom_checksum_generic,
+	.validate_checksum	= &ixgbe_validate_eeprom_checksum_generic,
+	.update_checksum	= &ixgbe_update_eeprom_checksum_generic,
 };
 
 static struct ixgbe_phy_operations phy_ops_82599 = {
-	.identify               = &ixgbe_identify_phy_82599,
-	.identify_sfp           = &ixgbe_identify_sfp_module_generic,
-	.init			            = &ixgbe_init_phy_ops_82599,
-	.reset                  = &ixgbe_reset_phy_generic,
-	.read_reg               = &ixgbe_read_phy_reg_generic,
-	.write_reg              = &ixgbe_write_phy_reg_generic,
-	.setup_link             = &ixgbe_setup_phy_link_generic,
-	.setup_link_speed       = &ixgbe_setup_phy_link_speed_generic,
-	.read_i2c_byte          = &ixgbe_read_i2c_byte_generic,
-	.write_i2c_byte         = &ixgbe_write_i2c_byte_generic,
-	.read_i2c_eeprom        = &ixgbe_read_i2c_eeprom_generic,
-	.write_i2c_eeprom       = &ixgbe_write_i2c_eeprom_generic,
-	.check_overtemp         = &ixgbe_tn_check_overtemp,
+	.identify		= &ixgbe_identify_phy_82599,
+	.identify_sfp		= &ixgbe_identify_sfp_module_generic,
+	.init			= &ixgbe_init_phy_ops_82599,
+	.reset			= &ixgbe_reset_phy_generic,
+	.read_reg		= &ixgbe_read_phy_reg_generic,
+	.write_reg		= &ixgbe_write_phy_reg_generic,
+	.setup_link		= &ixgbe_setup_phy_link_generic,
+	.setup_link_speed	= &ixgbe_setup_phy_link_speed_generic,
+	.read_i2c_byte		= &ixgbe_read_i2c_byte_generic,
+	.write_i2c_byte		= &ixgbe_write_i2c_byte_generic,
+	.read_i2c_eeprom	= &ixgbe_read_i2c_eeprom_generic,
+	.write_i2c_eeprom	= &ixgbe_write_i2c_eeprom_generic,
+	.check_overtemp		= &ixgbe_tn_check_overtemp,
 };
 
 struct ixgbe_info ixgbe_82599_info = {
diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c
index a7fb2e00f76..bcd952916eb 100644
--- a/drivers/net/ixgbe/ixgbe_common.c
+++ b/drivers/net/ixgbe/ixgbe_common.c
@@ -47,6 +47,12 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
 static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
 
 static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
+static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw);
+static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw);
+static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw);
+static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw);
+static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
+			      u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm);
 static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num);
 
 /**
@@ -136,17 +142,29 @@ s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
 	IXGBE_READ_REG(hw, IXGBE_MRFC);
 	IXGBE_READ_REG(hw, IXGBE_RLEC);
 	IXGBE_READ_REG(hw, IXGBE_LXONTXC);
-	IXGBE_READ_REG(hw, IXGBE_LXONRXC);
 	IXGBE_READ_REG(hw, IXGBE_LXOFFTXC);
-	IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
+	if (hw->mac.type >= ixgbe_mac_82599EB) {
+		IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
+		IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT);
+	} else {
+		IXGBE_READ_REG(hw, IXGBE_LXONRXC);
+		IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
+	}
 
 	for (i = 0; i < 8; i++) {
 		IXGBE_READ_REG(hw, IXGBE_PXONTXC(i));
-		IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
 		IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i));
-		IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
+		if (hw->mac.type >= ixgbe_mac_82599EB) {
+			IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i));
+			IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i));
+		} else {
+			IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
+			IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
+		}
 	}
-
+	if (hw->mac.type >= ixgbe_mac_82599EB)
+		for (i = 0; i < 8; i++)
+			IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i));
 	IXGBE_READ_REG(hw, IXGBE_PRC64);
 	IXGBE_READ_REG(hw, IXGBE_PRC127);
 	IXGBE_READ_REG(hw, IXGBE_PRC255);
@@ -184,9 +202,26 @@ s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
 	IXGBE_READ_REG(hw, IXGBE_BPTC);
 	for (i = 0; i < 16; i++) {
 		IXGBE_READ_REG(hw, IXGBE_QPRC(i));
-		IXGBE_READ_REG(hw, IXGBE_QBRC(i));
 		IXGBE_READ_REG(hw, IXGBE_QPTC(i));
-		IXGBE_READ_REG(hw, IXGBE_QBTC(i));
+		if (hw->mac.type >= ixgbe_mac_82599EB) {
+			IXGBE_READ_REG(hw, IXGBE_QBRC_L(i));
+			IXGBE_READ_REG(hw, IXGBE_QBRC_H(i));
+			IXGBE_READ_REG(hw, IXGBE_QBTC_L(i));
+			IXGBE_READ_REG(hw, IXGBE_QBTC_H(i));
+			IXGBE_READ_REG(hw, IXGBE_QPRDC(i));
+		} else {
+			IXGBE_READ_REG(hw, IXGBE_QBRC(i));
+			IXGBE_READ_REG(hw, IXGBE_QBTC(i));
+		}
+	}
+
+	if (hw->mac.type == ixgbe_mac_X540) {
+		if (hw->phy.id == 0)
+			hw->phy.ops.identify(hw);
+		hw->phy.ops.read_reg(hw, 0x3, IXGBE_PCRC8ECL, &i);
+		hw->phy.ops.read_reg(hw, 0x3, IXGBE_PCRC8ECH, &i);
+		hw->phy.ops.read_reg(hw, 0x3, IXGBE_LDPCECL, &i);
+		hw->phy.ops.read_reg(hw, 0x3, IXGBE_LDPCECH, &i);
 	}
 
 	return 0;
@@ -1075,7 +1110,7 @@ static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
 	eec &= ~IXGBE_EEC_REQ;
 	IXGBE_WRITE_REG(hw, IXGBE_EEC, eec);
 
-	ixgbe_release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+	hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
 
 	/* Delay before attempt to obtain semaphore again to allow FW access */
 	msleep(hw->eeprom.semaphore_delay);
@@ -1537,7 +1572,7 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num)
 #endif /* CONFIG_DCB */
 	/* Negotiate the fc mode to use */
 	ret_val = ixgbe_fc_autoneg(hw);
-	if (ret_val)
+	if (ret_val == IXGBE_ERR_FLOW_CONTROL)
 		goto out;
 
 	/* Disable any previous flow control settings */
@@ -1645,12 +1680,13 @@ out:
  **/
 s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 {
-	s32 ret_val = 0;
+	s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
 	ixgbe_link_speed speed;
-	u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
-	u32 links2, anlp1_reg, autoc_reg, links;
 	bool link_up;
 
+	if (hw->fc.disable_fc_autoneg)
+		goto out;
+
 	/*
 	 * AN should have completed when the cable was plugged in.
 	 * Look for reasons to bail out.  Bail out if:
@@ -1661,153 +1697,199 @@ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 	 * So use link_up_wait_to_complete=false.
 	 */
 	hw->mac.ops.check_link(hw, &speed, &link_up, false);
-
-	if (hw->fc.disable_fc_autoneg || (!link_up)) {
-		hw->fc.fc_was_autonegged = false;
-		hw->fc.current_mode = hw->fc.requested_mode;
+	if (!link_up) {
+		ret_val = IXGBE_ERR_FLOW_CONTROL;
 		goto out;
 	}
 
-	/*
-	 * On backplane, bail out if
-	 * - backplane autoneg was not completed, or if
-	 * - we are 82599 and link partner is not AN enabled
-	 */
-	if (hw->phy.media_type == ixgbe_media_type_backplane) {
-		links = IXGBE_READ_REG(hw, IXGBE_LINKS);
-		if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) {
-			hw->fc.fc_was_autonegged = false;
-			hw->fc.current_mode = hw->fc.requested_mode;
-			goto out;
-		}
+	switch (hw->phy.media_type) {
+	/* Autoneg flow control on fiber adapters */
+	case ixgbe_media_type_fiber:
+		if (speed == IXGBE_LINK_SPEED_1GB_FULL)
+			ret_val = ixgbe_fc_autoneg_fiber(hw);
+		break;
 
-		if (hw->mac.type == ixgbe_mac_82599EB) {
-			links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
-			if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) {
-				hw->fc.fc_was_autonegged = false;
-				hw->fc.current_mode = hw->fc.requested_mode;
-				goto out;
-			}
-		}
+	/* Autoneg flow control on backplane adapters */
+	case ixgbe_media_type_backplane:
+		ret_val = ixgbe_fc_autoneg_backplane(hw);
+		break;
+
+	/* Autoneg flow control on copper adapters */
+	case ixgbe_media_type_copper:
+		if (ixgbe_device_supports_autoneg_fc(hw) == 0)
+			ret_val = ixgbe_fc_autoneg_copper(hw);
+		break;
+
+	default:
+		break;
 	}
 
+out:
+	if (ret_val == 0) {
+		hw->fc.fc_was_autonegged = true;
+	} else {
+		hw->fc.fc_was_autonegged = false;
+		hw->fc.current_mode = hw->fc.requested_mode;
+	}
+	return ret_val;
+}
+
+/**
+ *  ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber
+ *  @hw: pointer to hardware structure
+ *
+ *  Enable flow control according on 1 gig fiber.
+ **/
+static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw)
+{
+	u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
+	s32 ret_val;
+
 	/*
 	 * On multispeed fiber at 1g, bail out if
 	 * - link is up but AN did not complete, or if
 	 * - link is up and AN completed but timed out
 	 */
-	if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL)) {
-		linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
-		if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
-		    ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) {
-			hw->fc.fc_was_autonegged = false;
-			hw->fc.current_mode = hw->fc.requested_mode;
-			goto out;
-		}
+
+	linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
+	if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
+	    ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) {
+		ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
+		goto out;
 	}
 
+	pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+	pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
+
+	ret_val =  ixgbe_negotiate_fc(hw, pcs_anadv_reg,
+			       pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE,
+			       IXGBE_PCS1GANA_ASM_PAUSE,
+			       IXGBE_PCS1GANA_SYM_PAUSE,
+			       IXGBE_PCS1GANA_ASM_PAUSE);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37
+ *  @hw: pointer to hardware structure
+ *
+ *  Enable flow control according to IEEE clause 37.
+ **/
+static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw)
+{
+	u32 links2, anlp1_reg, autoc_reg, links;
+	s32 ret_val;
+
 	/*
-	 * Bail out on
-	 * - copper or CX4 adapters
-	 * - fiber adapters running at 10gig
+	 * On backplane, bail out if
+	 * - backplane autoneg was not completed, or if
+	 * - we are 82599 and link partner is not AN enabled
 	 */
-	if ((hw->phy.media_type == ixgbe_media_type_copper) ||
-	     (hw->phy.media_type == ixgbe_media_type_cx4) ||
-	     ((hw->phy.media_type == ixgbe_media_type_fiber) &&
-	     (speed == IXGBE_LINK_SPEED_10GB_FULL))) {
+	links = IXGBE_READ_REG(hw, IXGBE_LINKS);
+	if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) {
 		hw->fc.fc_was_autonegged = false;
 		hw->fc.current_mode = hw->fc.requested_mode;
+		ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
 		goto out;
 	}
 
+	if (hw->mac.type == ixgbe_mac_82599EB) {
+		links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
+		if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) {
+			hw->fc.fc_was_autonegged = false;
+			hw->fc.current_mode = hw->fc.requested_mode;
+			ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
+			goto out;
+		}
+	}
 	/*
-	 * Read the AN advertisement and LP ability registers and resolve
+	 * Read the 10g AN autoc and LP ability registers and resolve
 	 * local flow control settings accordingly
 	 */
-	if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
-	    (hw->phy.media_type != ixgbe_media_type_backplane)) {
-		pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
-		pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
-		if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
-		    (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) {
-			/*
-			 * Now we need to check if the user selected Rx ONLY
-			 * of pause frames.  In this case, we had to advertise
-			 * FULL flow control because we could not advertise RX
-			 * ONLY. Hence, we must now check to see if we need to
-			 * turn OFF the TRANSMISSION of PAUSE frames.
-			 */
-			if (hw->fc.requested_mode == ixgbe_fc_full) {
-				hw->fc.current_mode = ixgbe_fc_full;
-				hw_dbg(hw, "Flow Control = FULL.\n");
-			} else {
-				hw->fc.current_mode = ixgbe_fc_rx_pause;
-				hw_dbg(hw, "Flow Control=RX PAUSE only\n");
-			}
-		} else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
-			   (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
-			   (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
-			   (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
-			hw->fc.current_mode = ixgbe_fc_tx_pause;
-			hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
-		} else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
-			   (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
-			   !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
-			   (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
-			hw->fc.current_mode = ixgbe_fc_rx_pause;
-			hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
-		} else {
-			hw->fc.current_mode = ixgbe_fc_none;
-			hw_dbg(hw, "Flow Control = NONE.\n");
-		}
-	}
+	autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+	anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
 
-	if (hw->phy.media_type == ixgbe_media_type_backplane) {
+	ret_val = ixgbe_negotiate_fc(hw, autoc_reg,
+		anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE,
+		IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37
+ *  @hw: pointer to hardware structure
+ *
+ *  Enable flow control according to IEEE clause 37.
+ **/
+static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
+{
+	u16 technology_ability_reg = 0;
+	u16 lp_technology_ability_reg = 0;
+
+	hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
+			     MDIO_MMD_AN,
+			     &technology_ability_reg);
+	hw->phy.ops.read_reg(hw, MDIO_AN_LPA,
+			     MDIO_MMD_AN,
+			     &lp_technology_ability_reg);
+
+	return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg,
+				  (u32)lp_technology_ability_reg,
+				  IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE,
+				  IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE);
+}
+
+/**
+ *  ixgbe_negotiate_fc - Negotiate flow control
+ *  @hw: pointer to hardware structure
+ *  @adv_reg: flow control advertised settings
+ *  @lp_reg: link partner's flow control settings
+ *  @adv_sym: symmetric pause bit in advertisement
+ *  @adv_asm: asymmetric pause bit in advertisement
+ *  @lp_sym: symmetric pause bit in link partner advertisement
+ *  @lp_asm: asymmetric pause bit in link partner advertisement
+ *
+ *  Find the intersection between advertised settings and link partner's
+ *  advertised settings
+ **/
+static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
+			      u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
+{
+	if ((!(adv_reg)) ||  (!(lp_reg)))
+		return IXGBE_ERR_FC_NOT_NEGOTIATED;
+
+	if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
 		/*
-		 * Read the 10g AN autoc and LP ability registers and resolve
-		 * local flow control settings accordingly
+		 * Now we need to check if the user selected Rx ONLY
+		 * of pause frames.  In this case, we had to advertise
+		 * FULL flow control because we could not advertise RX
+		 * ONLY. Hence, we must now check to see if we need to
+		 * turn OFF the TRANSMISSION of PAUSE frames.
 		 */
-		autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
-		anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
-
-		if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
-		    (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE)) {
-			/*
-			 * Now we need to check if the user selected Rx ONLY
-			 * of pause frames.  In this case, we had to advertise
-			 * FULL flow control because we could not advertise RX
-			 * ONLY. Hence, we must now check to see if we need to
-			 * turn OFF the TRANSMISSION of PAUSE frames.
-			 */
-			if (hw->fc.requested_mode == ixgbe_fc_full) {
-				hw->fc.current_mode = ixgbe_fc_full;
-				hw_dbg(hw, "Flow Control = FULL.\n");
-			} else {
-				hw->fc.current_mode = ixgbe_fc_rx_pause;
-				hw_dbg(hw, "Flow Control=RX PAUSE only\n");
-			}
-		} else if (!(autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
-			   (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
-			   (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
-			   (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
-			hw->fc.current_mode = ixgbe_fc_tx_pause;
-			hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
-		} else if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
-			   (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
-			   !(anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
-			   (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
-			hw->fc.current_mode = ixgbe_fc_rx_pause;
-			hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+		if (hw->fc.requested_mode == ixgbe_fc_full) {
+			hw->fc.current_mode = ixgbe_fc_full;
+			hw_dbg(hw, "Flow Control = FULL.\n");
 		} else {
-			hw->fc.current_mode = ixgbe_fc_none;
-			hw_dbg(hw, "Flow Control = NONE.\n");
+			hw->fc.current_mode = ixgbe_fc_rx_pause;
+			hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
 		}
+	} else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+		   (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+		hw->fc.current_mode = ixgbe_fc_tx_pause;
+		hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+	} else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+		   !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+		hw->fc.current_mode = ixgbe_fc_rx_pause;
+		hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+	} else {
+		hw->fc.current_mode = ixgbe_fc_none;
+		hw_dbg(hw, "Flow Control = NONE.\n");
 	}
-	/* Record that current_mode is the result of a successful autoneg */
-	hw->fc.fc_was_autonegged = true;
-
-out:
-	return ret_val;
+	return 0;
 }
 
 /**
@@ -1819,7 +1901,8 @@ out:
 static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 {
 	s32 ret_val = 0;
-	u32 reg;
+	u32 reg = 0, reg_bp = 0;
+	u16 reg_cu = 0;
 
 #ifdef CONFIG_DCB
 	if (hw->fc.requested_mode == ixgbe_fc_pfc) {
@@ -1827,7 +1910,7 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 		goto out;
 	}
 
-#endif
+#endif /* CONFIG_DCB */
 	/* Validate the packetbuf configuration */
 	if (packetbuf_num < 0 || packetbuf_num > 7) {
 		hw_dbg(hw, "Invalid packet buffer number [%d], expected range "
@@ -1865,11 +1948,26 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 		hw->fc.requested_mode = ixgbe_fc_full;
 
 	/*
-	 * Set up the 1G flow control advertisement registers so the HW will be
-	 * able to do fc autoneg once the cable is plugged in.  If we end up
-	 * using 10g instead, this is harmless.
+	 * Set up the 1G and 10G flow control advertisement registers so the
+	 * HW will be able to do fc autoneg once the cable is plugged in.  If
+	 * we link at 10G, the 1G advertisement is harmless and vice versa.
 	 */
-	reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+
+	switch (hw->phy.media_type) {
+	case ixgbe_media_type_fiber:
+	case ixgbe_media_type_backplane:
+		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+		reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+		break;
+
+	case ixgbe_media_type_copper:
+		hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
+					MDIO_MMD_AN, &reg_cu);
+		break;
+
+	default:
+		;
+	}
 
 	/*
 	 * The possible values of fc.requested_mode are:
@@ -1888,6 +1986,11 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 	case ixgbe_fc_none:
 		/* Flow control completely disabled by software override. */
 		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
+				    IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
 		break;
 	case ixgbe_fc_rx_pause:
 		/*
@@ -1899,6 +2002,11 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 		 * disable the adapter's ability to send PAUSE frames.
 		 */
 		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+				   IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
 		break;
 	case ixgbe_fc_tx_pause:
 		/*
@@ -1907,10 +2015,22 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 		 */
 		reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
 		reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane) {
+			reg_bp |= (IXGBE_AUTOC_ASM_PAUSE);
+			reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE);
+		} else if (hw->phy.media_type == ixgbe_media_type_copper) {
+			reg_cu |= (IXGBE_TAF_ASM_PAUSE);
+			reg_cu &= ~(IXGBE_TAF_SYM_PAUSE);
+		}
 		break;
 	case ixgbe_fc_full:
 		/* Flow control (both Rx and Tx) is enabled by SW override. */
 		reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+		if (hw->phy.media_type == ixgbe_media_type_backplane)
+			reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+				   IXGBE_AUTOC_ASM_PAUSE);
+		else if (hw->phy.media_type == ixgbe_media_type_copper)
+			reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
 		break;
 #ifdef CONFIG_DCB
 	case ixgbe_fc_pfc:
@@ -1924,80 +2044,37 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 		break;
 	}
 
-	IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
-	reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
-
-	/* Disable AN timeout */
-	if (hw->fc.strict_ieee)
-		reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
+	if (hw->mac.type != ixgbe_mac_X540) {
+		/*
+		 * Enable auto-negotiation between the MAC & PHY;
+		 * the MAC will advertise clause 37 flow control.
+		 */
+		IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
+		reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
 
-	IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
-	hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+		/* Disable AN timeout */
+		if (hw->fc.strict_ieee)
+			reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
 
-	/*
-	 * Set up the 10G flow control advertisement registers so the HW
-	 * can do fc autoneg once the cable is plugged in.  If we end up
-	 * using 1g instead, this is harmless.
-	 */
-	reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+		IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
+		hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+	}
 
 	/*
-	 * The possible values of fc.requested_mode are:
-	 * 0: Flow control is completely disabled
-	 * 1: Rx flow control is enabled (we can receive pause frames,
-	 *    but not send pause frames).
-	 * 2: Tx flow control is enabled (we can send pause frames but
-	 *    we do not support receiving pause frames).
-	 * 3: Both Rx and Tx flow control (symmetric) are enabled.
-	 * other: Invalid.
+	 * AUTOC restart handles negotiation of 1G and 10G on backplane
+	 * and copper. There is no need to set the PCS1GCTL register.
+	 *
 	 */
-	switch (hw->fc.requested_mode) {
-	case ixgbe_fc_none:
-		/* Flow control completely disabled by software override. */
-		reg &= ~(IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
-		break;
-	case ixgbe_fc_rx_pause:
-		/*
-		 * Rx Flow control is enabled and Tx Flow control is
-		 * disabled by software override. Since there really
-		 * isn't a way to advertise that we are capable of RX
-		 * Pause ONLY, we will advertise that we support both
-		 * symmetric and asymmetric Rx PAUSE.  Later, we will
-		 * disable the adapter's ability to send PAUSE frames.
-		 */
-		reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
-		break;
-	case ixgbe_fc_tx_pause:
-		/*
-		 * Tx Flow control is enabled, and Rx Flow control is
-		 * disabled by software override.
-		 */
-		reg |= (IXGBE_AUTOC_ASM_PAUSE);
-		reg &= ~(IXGBE_AUTOC_SYM_PAUSE);
-		break;
-	case ixgbe_fc_full:
-		/* Flow control (both Rx and Tx) is enabled by SW override. */
-		reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
-		break;
-#ifdef CONFIG_DCB
-	case ixgbe_fc_pfc:
-		goto out;
-		break;
-#endif /* CONFIG_DCB */
-	default:
-		hw_dbg(hw, "Flow control param set incorrectly\n");
-		ret_val = IXGBE_ERR_CONFIG;
-		goto out;
-		break;
+	if (hw->phy.media_type == ixgbe_media_type_backplane) {
+		reg_bp |= IXGBE_AUTOC_AN_RESTART;
+		IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp);
+	} else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
+		    (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
+		hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
+				      MDIO_MMD_AN, reg_cu);
 	}
-	/*
-	 * AUTOC restart handles negotiation of 1G and 10G. There is
-	 * no need to set the PCS1GCTL register.
-	 */
-	reg |= IXGBE_AUTOC_AN_RESTART;
-	IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg);
-	hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
 
+	hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
 out:
 	return ret_val;
 }
@@ -2085,7 +2162,7 @@ out:
  *  @hw: pointer to hardware structure
  *  @mask: Mask to specify which semaphore to acquire
  *
- *  Acquires the SWFW semaphore thought the GSSR register for the specified
+ *  Acquires the SWFW semaphore through the GSSR register for the specified
  *  function (CSR, PHY0, PHY1, EEPROM, Flash)
  **/
 s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask)
@@ -2133,7 +2210,7 @@ s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask)
  *  @hw: pointer to hardware structure
  *  @mask: Mask to specify which semaphore to release
  *
- *  Releases the SWFW semaphore thought the GSSR register for the specified
+ *  Releases the SWFW semaphore through the GSSR register for the specified
  *  function (CSR, PHY0, PHY1, EEPROM, Flash)
  **/
 void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask)
@@ -2722,6 +2799,28 @@ wwn_prefix_out:
 }
 
 /**
+ *  ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
+ *  control
+ *  @hw: pointer to hardware structure
+ *
+ *  There are several phys that do not support autoneg flow control. This
+ *  function check the device id to see if the associated phy supports
+ *  autoneg flow control.
+ **/
+static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
+{
+
+	switch (hw->device_id) {
+	case IXGBE_DEV_ID_X540T:
+		return 0;
+	case IXGBE_DEV_ID_82599_T3_LOM:
+		return 0;
+	default:
+		return IXGBE_ERR_FC_NOT_SUPPORTED;
+	}
+}
+
+/**
  *  ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
  *  @hw: pointer to hardware structure
  *  @enable: enable or disable switch for anti-spoofing
diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 83511c02292..76380a2b35a 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -161,29 +161,25 @@ static int ixgbe_get_settings(struct net_device *netdev,
 		}
 
 		ecmd->advertising = ADVERTISED_Autoneg;
-		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
-			ecmd->advertising |= ADVERTISED_100baseT_Full;
-		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL)
-			ecmd->advertising |= ADVERTISED_10000baseT_Full;
-		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL)
-			ecmd->advertising |= ADVERTISED_1000baseT_Full;
-		/*
-		 * It's possible that phy.autoneg_advertised may not be
-		 * set yet.  If so display what the default would be -
-		 * both 1G and 10G supported.
-		 */
-		if (!(ecmd->advertising & (ADVERTISED_1000baseT_Full |
-					   ADVERTISED_10000baseT_Full)))
+		if (hw->phy.autoneg_advertised) {
+			if (hw->phy.autoneg_advertised &
+			    IXGBE_LINK_SPEED_100_FULL)
+				ecmd->advertising |= ADVERTISED_100baseT_Full;
+			if (hw->phy.autoneg_advertised &
+			    IXGBE_LINK_SPEED_10GB_FULL)
+				ecmd->advertising |= ADVERTISED_10000baseT_Full;
+			if (hw->phy.autoneg_advertised &
+			    IXGBE_LINK_SPEED_1GB_FULL)
+				ecmd->advertising |= ADVERTISED_1000baseT_Full;
+		} else {
+			/*
+			 * Default advertised modes in case
+			 * phy.autoneg_advertised isn't set.
+			 */
 			ecmd->advertising |= (ADVERTISED_10000baseT_Full |
 					      ADVERTISED_1000baseT_Full);
-
-		switch (hw->mac.type) {
-		case ixgbe_mac_X540:
-			if (!(ecmd->advertising & ADVERTISED_100baseT_Full))
-				ecmd->advertising |= (ADVERTISED_100baseT_Full);
-			break;
-		default:
-			break;
+			if (hw->mac.type == ixgbe_mac_X540)
+				ecmd->advertising |= ADVERTISED_100baseT_Full;
 		}
 
 		if (hw->phy.media_type == ixgbe_media_type_copper) {
@@ -336,6 +332,9 @@ static int ixgbe_set_settings(struct net_device *netdev,
 		if (ecmd->advertising & ADVERTISED_1000baseT_Full)
 			advertised |= IXGBE_LINK_SPEED_1GB_FULL;
 
+		if (ecmd->advertising & ADVERTISED_100baseT_Full)
+			advertised |= IXGBE_LINK_SPEED_100_FULL;
+
 		if (old == advertised)
 			return err;
 		/* this sets the link speed and restarts auto-neg */
diff --git a/drivers/net/ixgbe/ixgbe_fcoe.c b/drivers/net/ixgbe/ixgbe_fcoe.c
index 27203c87ea1..00af15a9cdc 100644
--- a/drivers/net/ixgbe/ixgbe_fcoe.c
+++ b/drivers/net/ixgbe/ixgbe_fcoe.c
@@ -135,22 +135,19 @@ out_ddp_put:
 	return len;
 }
 
+
 /**
- * ixgbe_fcoe_ddp_get - called to set up ddp context
+ * ixgbe_fcoe_ddp_setup - called to set up ddp context
  * @netdev: the corresponding net_device
  * @xid: the exchange id requesting ddp
  * @sgl: the scatter-gather list for this request
  * @sgc: the number of scatter-gather items
  *
- * This is the implementation of net_device_ops.ndo_fcoe_ddp_setup
- * and is expected to be called from ULD, e.g., FCP layer of libfc
- * to set up ddp for the corresponding xid of the given sglist for
- * the corresponding I/O.
- *
  * Returns : 1 for success and 0 for no ddp
  */
-int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
-		       struct scatterlist *sgl, unsigned int sgc)
+static int ixgbe_fcoe_ddp_setup(struct net_device *netdev, u16 xid,
+				struct scatterlist *sgl, unsigned int sgc,
+				int target_mode)
 {
 	struct ixgbe_adapter *adapter;
 	struct ixgbe_hw *hw;
@@ -164,7 +161,7 @@ int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
 	unsigned int lastsize;
 	unsigned int thisoff = 0;
 	unsigned int thislen = 0;
-	u32 fcbuff, fcdmarw, fcfltrw;
+	u32 fcbuff, fcdmarw, fcfltrw, fcrxctl;
 	dma_addr_t addr = 0;
 
 	if (!netdev || !sgl)
@@ -275,6 +272,9 @@ int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
 	fcbuff = (IXGBE_FCBUFF_4KB << IXGBE_FCBUFF_BUFFSIZE_SHIFT);
 	fcbuff |= ((j & 0xff) << IXGBE_FCBUFF_BUFFCNT_SHIFT);
 	fcbuff |= (firstoff << IXGBE_FCBUFF_OFFSET_SHIFT);
+	/* Set WRCONTX bit to allow DDP for target */
+	if (target_mode)
+		fcbuff |= (IXGBE_FCBUFF_WRCONTX);
 	fcbuff |= (IXGBE_FCBUFF_VALID);
 
 	fcdmarw = xid;
@@ -287,6 +287,16 @@ int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
 	/* program DMA context */
 	hw = &adapter->hw;
 	spin_lock_bh(&fcoe->lock);
+
+	/* turn on last frame indication for target mode as FCP_RSPtarget is
+	 * supposed to send FCP_RSP when it is done. */
+	if (target_mode && !test_bit(__IXGBE_FCOE_TARGET, &fcoe->mode)) {
+		set_bit(__IXGBE_FCOE_TARGET, &fcoe->mode);
+		fcrxctl = IXGBE_READ_REG(hw, IXGBE_FCRXCTRL);
+		fcrxctl |= IXGBE_FCRXCTRL_LASTSEQH;
+		IXGBE_WRITE_REG(hw, IXGBE_FCRXCTRL, fcrxctl);
+	}
+
 	IXGBE_WRITE_REG(hw, IXGBE_FCPTRL, ddp->udp & DMA_BIT_MASK(32));
 	IXGBE_WRITE_REG(hw, IXGBE_FCPTRH, (u64)ddp->udp >> 32);
 	IXGBE_WRITE_REG(hw, IXGBE_FCBUFF, fcbuff);
@@ -295,6 +305,7 @@ int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
 	IXGBE_WRITE_REG(hw, IXGBE_FCPARAM, 0);
 	IXGBE_WRITE_REG(hw, IXGBE_FCFLT, IXGBE_FCFLT_VALID);
 	IXGBE_WRITE_REG(hw, IXGBE_FCFLTRW, fcfltrw);
+
 	spin_unlock_bh(&fcoe->lock);
 
 	return 1;
@@ -309,6 +320,47 @@ out_noddp_unmap:
 }
 
 /**
+ * ixgbe_fcoe_ddp_get - called to set up ddp context in initiator mode
+ * @netdev: the corresponding net_device
+ * @xid: the exchange id requesting ddp
+ * @sgl: the scatter-gather list for this request
+ * @sgc: the number of scatter-gather items
+ *
+ * This is the implementation of net_device_ops.ndo_fcoe_ddp_setup
+ * and is expected to be called from ULD, e.g., FCP layer of libfc
+ * to set up ddp for the corresponding xid of the given sglist for
+ * the corresponding I/O.
+ *
+ * Returns : 1 for success and 0 for no ddp
+ */
+int ixgbe_fcoe_ddp_get(struct net_device *netdev, u16 xid,
+		       struct scatterlist *sgl, unsigned int sgc)
+{
+	return ixgbe_fcoe_ddp_setup(netdev, xid, sgl, sgc, 0);
+}
+
+/**
+ * ixgbe_fcoe_ddp_target - called to set up ddp context in target mode
+ * @netdev: the corresponding net_device
+ * @xid: the exchange id requesting ddp
+ * @sgl: the scatter-gather list for this request
+ * @sgc: the number of scatter-gather items
+ *
+ * This is the implementation of net_device_ops.ndo_fcoe_ddp_target
+ * and is expected to be called from ULD, e.g., FCP layer of libfc
+ * to set up ddp for the corresponding xid of the given sglist for
+ * the corresponding I/O. The DDP in target mode is a write I/O request
+ * from the initiator.
+ *
+ * Returns : 1 for success and 0 for no ddp
+ */
+int ixgbe_fcoe_ddp_target(struct net_device *netdev, u16 xid,
+			    struct scatterlist *sgl, unsigned int sgc)
+{
+	return ixgbe_fcoe_ddp_setup(netdev, xid, sgl, sgc, 1);
+}
+
+/**
  * ixgbe_fcoe_ddp - check ddp status and mark it done
  * @adapter: ixgbe adapter
  * @rx_desc: advanced rx descriptor
@@ -331,6 +383,7 @@ int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter,
 	struct ixgbe_fcoe *fcoe;
 	struct ixgbe_fcoe_ddp *ddp;
 	struct fc_frame_header *fh;
+	struct fcoe_crc_eof *crc;
 
 	if (!ixgbe_rx_is_fcoe(rx_desc))
 		goto ddp_out;
@@ -384,7 +437,18 @@ int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter,
 		else if (ddp->len)
 			rc = ddp->len;
 	}
-
+	/* In target mode, check the last data frame of the sequence.
+	 * For DDP in target mode, data is already DDPed but the header
+	 * indication of the last data frame ould allow is to tell if we
+	 * got all the data and the ULP can send FCP_RSP back, as this is
+	 * not a full fcoe frame, we fill the trailer here so it won't be
+	 * dropped by the ULP stack.
+	 */
+	if ((fh->fh_r_ctl == FC_RCTL_DD_SOL_DATA) &&
+	    (fctl & FC_FC_END_SEQ)) {
+		crc = (struct fcoe_crc_eof *)skb_put(skb, sizeof(*crc));
+		crc->fcoe_eof = FC_EOF_T;
+	}
 ddp_out:
 	return rc;
 }
@@ -840,5 +904,3 @@ int ixgbe_fcoe_get_wwn(struct net_device *netdev, u64 *wwn, int type)
 	}
 	return rc;
 }
-
-
diff --git a/drivers/net/ixgbe/ixgbe_fcoe.h b/drivers/net/ixgbe/ixgbe_fcoe.h
index 02a00d2415d..5a650a4ace6 100644
--- a/drivers/net/ixgbe/ixgbe_fcoe.h
+++ b/drivers/net/ixgbe/ixgbe_fcoe.h
@@ -52,6 +52,9 @@
 /* fcerr */
 #define IXGBE_FCERR_BADCRC       0x00100000
 
+/* FCoE DDP for target mode */
+#define __IXGBE_FCOE_TARGET	1
+
 struct ixgbe_fcoe_ddp {
 	int len;
 	u32 err;
@@ -66,6 +69,7 @@ struct ixgbe_fcoe {
 	u8 tc;
 	u8 up;
 #endif
+	unsigned long mode;
 	atomic_t refcnt;
 	spinlock_t lock;
 	struct pci_pool *pool;
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 32231ffe071..5998dc94dd5 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -3775,7 +3775,8 @@ static int ixgbe_non_sfp_link_config(struct ixgbe_hw *hw)
 	if (ret)
 		goto link_cfg_out;
 
-	if (hw->mac.ops.get_link_capabilities)
+	autoneg = hw->phy.autoneg_advertised;
+	if ((!autoneg) && (hw->mac.ops.get_link_capabilities))
 		ret = hw->mac.ops.get_link_capabilities(hw, &autoneg,
 							&negotiation);
 	if (ret)
@@ -7019,6 +7020,7 @@ static const struct net_device_ops ixgbe_netdev_ops = {
 #endif
 #ifdef IXGBE_FCOE
 	.ndo_fcoe_ddp_setup = ixgbe_fcoe_ddp_get,
+	.ndo_fcoe_ddp_target = ixgbe_fcoe_ddp_target,
 	.ndo_fcoe_ddp_done = ixgbe_fcoe_ddp_put,
 	.ndo_fcoe_enable = ixgbe_fcoe_enable,
 	.ndo_fcoe_disable = ixgbe_fcoe_disable,
diff --git a/drivers/net/ixgbe/ixgbe_mbx.c b/drivers/net/ixgbe/ixgbe_mbx.c
index 2acacfa5e37..3cf8aec50fc 100644
--- a/drivers/net/ixgbe/ixgbe_mbx.c
+++ b/drivers/net/ixgbe/ixgbe_mbx.c
@@ -448,23 +448,20 @@ void ixgbe_init_mbx_params_pf(struct ixgbe_hw *hw)
 {
 	struct ixgbe_mbx_info *mbx = &hw->mbx;
 
-	switch (hw->mac.type) {
-	case ixgbe_mac_82599EB:
-	case ixgbe_mac_X540:
-		mbx->timeout = 0;
-		mbx->usec_delay = 0;
+	if (hw->mac.type != ixgbe_mac_82599EB &&
+	    hw->mac.type != ixgbe_mac_X540)
+		return;
 
-		mbx->size = IXGBE_VFMAILBOX_SIZE;
+	mbx->timeout = 0;
+	mbx->udelay = 0;
 
-		mbx->stats.msgs_tx = 0;
-		mbx->stats.msgs_rx = 0;
-		mbx->stats.reqs = 0;
-		mbx->stats.acks = 0;
-		mbx->stats.rsts = 0;
-		break;
-	default:
-		break;
-	}
+	mbx->stats.msgs_tx = 0;
+	mbx->stats.msgs_rx = 0;
+	mbx->stats.reqs = 0;
+	mbx->stats.acks = 0;
+	mbx->stats.rsts = 0;
+
+	mbx->size = IXGBE_VFMAILBOX_SIZE;
 }
 #endif /* CONFIG_PCI_IOV */
 
diff --git a/drivers/net/ixgbe/ixgbe_phy.c b/drivers/net/ixgbe/ixgbe_phy.c
index 197230b2d1a..9190a8fca42 100644
--- a/drivers/net/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ixgbe/ixgbe_phy.c
@@ -57,6 +57,7 @@ s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw)
 {
 	s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
 	u32 phy_addr;
+	u16 ext_ability = 0;
 
 	if (hw->phy.type == ixgbe_phy_unknown) {
 		for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) {
@@ -65,12 +66,29 @@ s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw)
 				ixgbe_get_phy_id(hw);
 				hw->phy.type =
 				        ixgbe_get_phy_type_from_id(hw->phy.id);
+
+				if (hw->phy.type == ixgbe_phy_unknown) {
+					hw->phy.ops.read_reg(hw,
+							     MDIO_PMA_EXTABLE,
+							     MDIO_MMD_PMAPMD,
+							     &ext_ability);
+					if (ext_ability &
+					    (MDIO_PMA_EXTABLE_10GBT |
+					     MDIO_PMA_EXTABLE_1000BT))
+						hw->phy.type =
+							 ixgbe_phy_cu_unknown;
+					else
+						hw->phy.type =
+							 ixgbe_phy_generic;
+				}
+
 				status = 0;
 				break;
 			}
 		}
 		/* clear value if nothing found */
-		hw->phy.mdio.prtad = 0;
+		if (status != 0)
+			hw->phy.mdio.prtad = 0;
 	} else {
 		status = 0;
 	}
@@ -823,7 +841,6 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
 			goto out;
 		}
 
-		/* This is guaranteed to be 82599, no need to check for NULL */
 		hw->mac.ops.get_device_caps(hw, &enforce_sfp);
 		if (!(enforce_sfp & IXGBE_DEVICE_CAPS_ALLOW_ANY_SFP) &&
 		    !((hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0) ||
diff --git a/drivers/net/ixgbe/ixgbe_phy.h b/drivers/net/ixgbe/ixgbe_phy.h
index 2327baf0442..9bf2783d7a7 100644
--- a/drivers/net/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ixgbe/ixgbe_phy.h
@@ -58,6 +58,10 @@
 #define IXGBE_I2C_EEPROM_STATUS_FAIL         0x2
 #define IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS  0x3
 
+/* Flow control defines */
+#define IXGBE_TAF_SYM_PAUSE                  0x400
+#define IXGBE_TAF_ASM_PAUSE                  0x800
+
 /* Bit-shift macros */
 #define IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT    24
 #define IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT    16
diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h
index 013751db5fc..f190a4a8faf 100644
--- a/drivers/net/ixgbe/ixgbe_type.h
+++ b/drivers/net/ixgbe/ixgbe_type.h
@@ -659,6 +659,8 @@
 #define IXGBE_QPTC(_i) (0x06030 + ((_i) * 0x40)) /* 16 of these */
 #define IXGBE_QBRC(_i) (0x01034 + ((_i) * 0x40)) /* 16 of these */
 #define IXGBE_QBTC(_i) (0x06034 + ((_i) * 0x40)) /* 16 of these */
+#define IXGBE_QBRC_L(_i) (0x01034 + ((_i) * 0x40)) /* 16 of these */
+#define IXGBE_QBRC_H(_i) (0x01038 + ((_i) * 0x40)) /* 16 of these */
 #define IXGBE_QPRDC(_i) (0x01430 + ((_i) * 0x40)) /* 16 of these */
 #define IXGBE_QBTC_L(_i) (0x08700 + ((_i) * 0x8)) /* 16 of these */
 #define IXGBE_QBTC_H(_i) (0x08704 + ((_i) * 0x8)) /* 16 of these */
@@ -669,6 +671,11 @@
 #define IXGBE_FCOEDWRC  0x0242C /* Number of FCoE DWords Received */
 #define IXGBE_FCOEPTC   0x08784 /* Number of FCoE Packets Transmitted */
 #define IXGBE_FCOEDWTC  0x08788 /* Number of FCoE DWords Transmitted */
+#define IXGBE_PCRC8ECL  0x0E810
+#define IXGBE_PCRC8ECH  0x0E811
+#define IXGBE_PCRC8ECH_MASK     0x1F
+#define IXGBE_LDPCECL   0x0E820
+#define IXGBE_LDPCECH   0x0E821
 
 /* Management */
 #define IXGBE_MAVTV(_i) (0x05010 + ((_i) * 4)) /* 8 of these (0-7) */
@@ -2691,6 +2698,9 @@ struct ixgbe_info {
 #define IXGBE_ERR_EEPROM_VERSION                -24
 #define IXGBE_ERR_NO_SPACE                      -25
 #define IXGBE_ERR_OVERTEMP                      -26
+#define IXGBE_ERR_FC_NOT_NEGOTIATED             -27
+#define IXGBE_ERR_FC_NOT_SUPPORTED              -28
+#define IXGBE_ERR_FLOW_CONTROL                  -29
 #define IXGBE_ERR_SFP_SETUP_NOT_COMPLETE        -30
 #define IXGBE_ERR_PBA_SECTION                   -31
 #define IXGBE_ERR_INVALID_ARGUMENT              -32
diff --git a/drivers/net/ixgbe/ixgbe_x540.c b/drivers/net/ixgbe/ixgbe_x540.c
index 2e3a2b4fa8b..f47e93fe32b 100644
--- a/drivers/net/ixgbe/ixgbe_x540.c
+++ b/drivers/net/ixgbe/ixgbe_x540.c
@@ -251,8 +251,11 @@ static u32 ixgbe_get_supported_physical_layer_X540(struct ixgbe_hw *hw)
 }
 
 /**
- * ixgbe_init_eeprom_params_X540 - Initialize EEPROM params
- * @hw: pointer to hardware structure
+ *  ixgbe_init_eeprom_params_X540 - Initialize EEPROM params
+ *  @hw: pointer to hardware structure
+ *
+ *  Initializes the EEPROM parameters ixgbe_eeprom_info within the
+ *  ixgbe_hw struct in order to set up EEPROM access.
  **/
 static s32 ixgbe_init_eeprom_params_X540(struct ixgbe_hw *hw)
 {
@@ -271,7 +274,7 @@ static s32 ixgbe_init_eeprom_params_X540(struct ixgbe_hw *hw)
 		                          IXGBE_EEPROM_WORD_SIZE_SHIFT);
 
 		hw_dbg(hw, "Eeprom params: type = %d, size = %d\n",
-		        eeprom->type, eeprom->word_size);
+		       eeprom->type, eeprom->word_size);
 	}
 
 	return 0;