MIPS: Alchemy: Au1300 SoC support

Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

6 files changed, 322 insertions, 29 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index a3afac4be73..cbe7a2fb779 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -299,11 +299,11 @@ config I2C_AT91
 	  unless your system can cope with those limitations.
 
 config I2C_AU1550
-	tristate "Au1550/Au1200 SMBus interface"
+	tristate "Au1550/Au1200/Au1300 SMBus interface"
 	depends on MIPS_ALCHEMY
 	help
 	  If you say yes to this option, support will be included for the
-	  Au1550 and Au1200 SMBus interface.
+	  Au1550/Au1200/Au1300 SMBus interface.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-au1550.
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c
index 5d3b9ae6452..dbd0c8a4e98 100644
--- a/drivers/mmc/host/au1xmmc.c
+++ b/drivers/mmc/host/au1xmmc.c
@@ -153,6 +153,7 @@ static inline int has_dbdma(void)
 {
 	switch (alchemy_get_cputype()) {
 	case ALCHEMY_CPU_AU1200:
+	case ALCHEMY_CPU_AU1300:
 		return 1;
 	default:
 		return 0;
@@ -768,11 +769,15 @@ static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 	config2 = au_readl(HOST_CONFIG2(host));
 	switch (ios->bus_width) {
+	case MMC_BUS_WIDTH_8:
+		config2 |= SD_CONFIG2_BB;
+		break;
 	case MMC_BUS_WIDTH_4:
+		config2 &= ~SD_CONFIG2_BB;
 		config2 |= SD_CONFIG2_WB;
 		break;
 	case MMC_BUS_WIDTH_1:
-		config2 &= ~SD_CONFIG2_WB;
+		config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB);
 		break;
 	}
 	au_writel(config2, HOST_CONFIG2(host));
@@ -943,7 +948,7 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev)
 	struct mmc_host *mmc;
 	struct au1xmmc_host *host;
 	struct resource *r;
-	int ret;
+	int ret, iflag;
 
 	mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
 	if (!mmc) {
@@ -982,37 +987,43 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "no IRQ defined\n");
 		goto out3;
 	}
-
 	host->irq = r->start;
-	/* IRQ is shared among both SD controllers */
-	ret = request_irq(host->irq, au1xmmc_irq, IRQF_SHARED,
-			  DRIVER_NAME, host);
-	if (ret) {
-		dev_err(&pdev->dev, "cannot grab IRQ\n");
-		goto out3;
-	}
 
 	mmc->ops = &au1xmmc_ops;
 
 	mmc->f_min =   450000;
 	mmc->f_max = 24000000;
 
+	mmc->max_blk_size = 2048;
+	mmc->max_blk_count = 512;
+
+	mmc->ocr_avail = AU1XMMC_OCR;
+	mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+	mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
+
+	iflag = IRQF_SHARED;	/* Au1100/Au1200: one int for both ctrls */
+
 	switch (alchemy_get_cputype()) {
 	case ALCHEMY_CPU_AU1100:
 		mmc->max_seg_size = AU1100_MMC_DESCRIPTOR_SIZE;
-		mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
 		break;
 	case ALCHEMY_CPU_AU1200:
 		mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
-		mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;
+		break;
+	case ALCHEMY_CPU_AU1300:
+		iflag = 0;	/* nothing is shared */
+		mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
+		mmc->f_max = 52000000;
+		if (host->ioarea->start == AU1100_SD0_PHYS_ADDR)
+			mmc->caps |= MMC_CAP_8_BIT_DATA;
 		break;
 	}
 
-	mmc->max_blk_size = 2048;
-	mmc->max_blk_count = 512;
-
-	mmc->ocr_avail = AU1XMMC_OCR;
-	mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+	ret = request_irq(host->irq, au1xmmc_irq, iflag, DRIVER_NAME, host);
+	if (ret) {
+		dev_err(&pdev->dev, "cannot grab IRQ\n");
+		goto out3;
+	}
 
 	host->status = HOST_S_IDLE;
 
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index a1fd73df541..369e092bf3d 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -87,12 +87,12 @@ config SPI_BFIN_SPORT
 	  Enable support for a SPI bus via the Blackfin SPORT peripheral.
 
 config SPI_AU1550
-	tristate "Au1550/Au12x0 SPI Controller"
+	tristate "Au1550/Au1200/Au1300 SPI Controller"
 	depends on MIPS_ALCHEMY && EXPERIMENTAL
 	select SPI_BITBANG
 	help
 	  If you say yes to this option, support will be included for the
-	  Au1550 SPI controller (may also work with Au1200,Au1210,Au1250).
+	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 
 config SPI_BITBANG
 	tristate "Utilities for Bitbanging SPI masters"
diff --git a/drivers/usb/host/alchemy-common.c b/drivers/usb/host/alchemy-common.c
index b4192c964d0..936af8359fb 100644
--- a/drivers/usb/host/alchemy-common.c
+++ b/drivers/usb/host/alchemy-common.c
@@ -52,9 +52,263 @@
 				 USBCFG_EBE | USBCFG_EME | USBCFG_OBE |	       \
 				 USBCFG_OME)
 
+/* Au1300 USB config registers */
+#define USB_DWC_CTRL1		0x00
+#define USB_DWC_CTRL2		0x04
+#define USB_VBUS_TIMER		0x10
+#define USB_SBUS_CTRL		0x14
+#define USB_MSR_ERR		0x18
+#define USB_DWC_CTRL3		0x1C
+#define USB_DWC_CTRL4		0x20
+#define USB_OTG_STATUS		0x28
+#define USB_DWC_CTRL5		0x2C
+#define USB_DWC_CTRL6		0x30
+#define USB_DWC_CTRL7		0x34
+#define USB_PHY_STATUS		0xC0
+#define USB_INT_STATUS		0xC4
+#define USB_INT_ENABLE		0xC8
+
+#define USB_DWC_CTRL1_OTGD	0x04 /* set to DISable OTG */
+#define USB_DWC_CTRL1_HSTRS	0x02 /* set to ENable EHCI */
+#define USB_DWC_CTRL1_DCRS	0x01 /* set to ENable UDC */
+
+#define USB_DWC_CTRL2_PHY1RS	0x04 /* set to enable PHY1 */
+#define USB_DWC_CTRL2_PHY0RS	0x02 /* set to enable PHY0 */
+#define USB_DWC_CTRL2_PHYRS	0x01 /* set to enable PHY */
+
+#define USB_DWC_CTRL3_OHCI1_CKEN	(1 << 19)
+#define USB_DWC_CTRL3_OHCI0_CKEN	(1 << 18)
+#define USB_DWC_CTRL3_EHCI0_CKEN	(1 << 17)
+#define USB_DWC_CTRL3_OTG0_CKEN		(1 << 16)
+
+#define USB_SBUS_CTRL_SBCA		0x04 /* coherent access */
+
+#define USB_INTEN_FORCE			0x20
+#define USB_INTEN_PHY			0x10
+#define USB_INTEN_UDC			0x08
+#define USB_INTEN_EHCI			0x04
+#define USB_INTEN_OHCI1			0x02
+#define USB_INTEN_OHCI0			0x01
 
 static DEFINE_SPINLOCK(alchemy_usb_lock);
 
+static inline void __au1300_usb_phyctl(void __iomem *base, int enable)
+{
+	unsigned long r, s;
+
+	r = __raw_readl(base + USB_DWC_CTRL2);
+	s = __raw_readl(base + USB_DWC_CTRL3);
+
+	s &= USB_DWC_CTRL3_OHCI1_CKEN | USB_DWC_CTRL3_OHCI0_CKEN |
+		USB_DWC_CTRL3_EHCI0_CKEN | USB_DWC_CTRL3_OTG0_CKEN;
+
+	if (enable) {
+		/* simply enable all PHYs */
+		r |= USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+		     USB_DWC_CTRL2_PHYRS;
+		__raw_writel(r, base + USB_DWC_CTRL2);
+		wmb();
+	} else if (!s) {
+		/* no USB block active, do disable all PHYs */
+		r &= ~(USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+		       USB_DWC_CTRL2_PHYRS);
+		__raw_writel(r, base + USB_DWC_CTRL2);
+		wmb();
+	}
+}
+
+static inline void __au1300_ohci_control(void __iomem *base, int enable, int id)
+{
+	unsigned long r;
+
+	if (enable) {
+		__raw_writel(1, base + USB_DWC_CTRL7);  /* start OHCI clock */
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);	/* enable OHCI block */
+		r |= (id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+			       : USB_DWC_CTRL3_OHCI1_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);	/* power up the PHYs */
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= (id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		/* reset the OHCI start clock bit */
+		__raw_writel(0, base + USB_DWC_CTRL7);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~((id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1);
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~((id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+				 : USB_DWC_CTRL3_OHCI1_CKEN);
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_ehci_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r |= USB_DWC_CTRL3_EHCI0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_HSTRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= USB_INTEN_EHCI;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~USB_INTEN_EHCI;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_HSTRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~USB_DWC_CTRL3_EHCI0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_udc_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_DCRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= USB_INTEN_UDC;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~USB_INTEN_UDC;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_DCRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_otg_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r |= USB_DWC_CTRL3_OTG0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_OTGD;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	} else {
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_OTGD;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~USB_DWC_CTRL3_OTG0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline int au1300_usb_control(int block, int enable)
+{
+	void __iomem *base =
+		(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+	int ret = 0;
+
+	switch (block) {
+	case ALCHEMY_USB_OHCI0:
+		__au1300_ohci_control(base, enable, 0);
+		break;
+	case ALCHEMY_USB_OHCI1:
+		__au1300_ohci_control(base, enable, 1);
+		break;
+	case ALCHEMY_USB_EHCI0:
+		__au1300_ehci_control(base, enable);
+		break;
+	case ALCHEMY_USB_UDC0:
+		__au1300_udc_control(base, enable);
+		break;
+	case ALCHEMY_USB_OTG0:
+		__au1300_otg_control(base, enable);
+		break;
+	default:
+		ret = -ENODEV;
+	}
+	return ret;
+}
+
+static inline void au1300_usb_init(void)
+{
+	void __iomem *base =
+		(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+
+	/* set some sane defaults.  Note: we don't fiddle with DWC_CTRL4
+	 * here at all: Port 2 routing (EHCI or UDC) must be set either
+	 * by boot firmware or platform init code; I can't autodetect
+	 * a sane setting.
+	 */
+	__raw_writel(0, base + USB_INT_ENABLE); /* disable all USB irqs */
+	wmb();
+	__raw_writel(0, base + USB_DWC_CTRL3); /* disable all clocks */
+	wmb();
+	__raw_writel(~0, base + USB_MSR_ERR); /* clear all errors */
+	wmb();
+	__raw_writel(~0, base + USB_INT_STATUS); /* clear int status */
+	wmb();
+	/* set coherent access bit */
+	__raw_writel(USB_SBUS_CTRL_SBCA, base + USB_SBUS_CTRL);
+	wmb();
+}
 
 static inline void __au1200_ohci_control(void __iomem *base, int enable)
 {
@@ -233,6 +487,9 @@ int alchemy_usb_control(int block, int enable)
 	case ALCHEMY_CPU_AU1200:
 		ret = au1200_usb_control(block, enable);
 		break;
+	case ALCHEMY_CPU_AU1300:
+		ret = au1300_usb_control(block, enable);
+		break;
 	default:
 		ret = -ENODEV;
 	}
@@ -281,6 +538,20 @@ static void au1200_usb_pm(int susp)
 	}
 }
 
+static void au1300_usb_pm(int susp)
+{
+	void __iomem *base =
+			(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+	/* remember Port2 routing */
+	if (susp) {
+		alchemy_usb_pmdata[0] = __raw_readl(base + USB_DWC_CTRL4);
+	} else {
+		au1300_usb_init();
+		__raw_writel(alchemy_usb_pmdata[0], base + USB_DWC_CTRL4);
+		wmb();
+	}
+}
+
 static void alchemy_usb_pm(int susp)
 {
 	switch (alchemy_get_cputype()) {
@@ -295,6 +566,9 @@ static void alchemy_usb_pm(int susp)
 	case ALCHEMY_CPU_AU1200:
 		au1200_usb_pm(susp);
 		break;
+	case ALCHEMY_CPU_AU1300:
+		au1300_usb_pm(susp);
+		break;
 	}
 }
 
@@ -328,6 +602,9 @@ static int __init alchemy_usb_init(void)
 	case ALCHEMY_CPU_AU1200:
 		au1200_usb_init();
 		break;
+	case ALCHEMY_CPU_AU1300:
+		au1300_usb_init();
+		break;
 	}
 
 	register_syscore_ops(&alchemy_usb_pm_ops);
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 9b66df8278f..95d1a71dcca 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -89,7 +89,7 @@ static const struct hc_driver ohci_au1xxx_hc_driver = {
 
 static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
 {
-	int ret;
+	int ret, unit;
 	struct usb_hcd *hcd;
 
 	if (usb_disabled())
@@ -120,7 +120,9 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
 		goto err2;
 	}
 
-	if (alchemy_usb_control(ALCHEMY_USB_OHCI0, 1)) {
+	unit = (hcd->rsrc_start == AU1300_USB_OHCI1_PHYS_ADDR) ?
+			ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
+	if (alchemy_usb_control(unit, 1)) {
 		printk(KERN_INFO "%s: controller init failed!\n", pdev->name);
 		ret = -ENODEV;
 		goto err3;
@@ -135,7 +137,7 @@ static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
+	alchemy_usb_control(unit, 0);
 err3:
 	iounmap(hcd->regs);
 err2:
@@ -148,9 +150,12 @@ err1:
 static int ohci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+	int unit;
 
+	unit = (hcd->rsrc_start == AU1300_USB_OHCI1_PHYS_ADDR) ?
+			ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
 	usb_remove_hcd(hcd);
-	alchemy_usb_control(ALCHEMY_USB_OHCI0, 0);
+	alchemy_usb_control(unit, 0);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 	usb_put_hcd(hcd);
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index d83e967e4e1..acd4ba555e3 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1763,16 +1763,16 @@ config FB_AU1100
 	  au1100fb:panel=<name>.
 
 config FB_AU1200
-	bool "Au1200 LCD Driver"
+	bool "Au1200/Au1300 LCD Driver"
 	depends on (FB = y) && MIPS_ALCHEMY
 	select FB_SYS_FILLRECT
 	select FB_SYS_COPYAREA
 	select FB_SYS_IMAGEBLIT
 	select FB_SYS_FOPS
 	help
-	  This is the framebuffer driver for the AMD Au1200 SOC.  It can drive
-	  various panels and CRTs by passing in kernel cmd line option
-	  au1200fb:panel=<name>.
+	  This is the framebuffer driver for the Au1200/Au1300 SOCs.
+	  It can drive various panels and CRTs by passing in kernel cmd line
+	  option au1200fb:panel=<name>.
 
 config FB_VT8500
 	bool "VT8500 LCD Driver"