hwmon: adm1021 clean ups

This patch provides some coding standard cleanups and general code improvements
(more debug info, signed values for temperatures, changed names of ADM1023
regs, removed read/write_value functions).

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>

1 files changed, 122 insertions, 104 deletions

diff --git a/drivers/hwmon/adm1021.c b/drivers/hwmon/adm1021.c
index c466329b2ef..5418a675bb6 100644
--- a/drivers/hwmon/adm1021.c
+++ b/drivers/hwmon/adm1021.c
@@ -1,6 +1,6 @@
 /*
     adm1021.c - Part of lm_sensors, Linux kernel modules for hardware
-             monitoring
+		monitoring
     Copyright (c) 1998, 1999  Frodo Looijaard <frodol@dds.nl> and
     Philip Edelbrock <phil@netroedge.com>
 
@@ -32,11 +32,12 @@
 /* Addresses to scan */
 static unsigned short normal_i2c[] = { 0x18, 0x19, 0x1a,
 					0x29, 0x2a, 0x2b,
-					0x4c, 0x4d, 0x4e, 
+					0x4c, 0x4d, 0x4e,
 					I2C_CLIENT_END };
 
 /* Insmod parameters */
-I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm, mc1066);
+I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm,
+			mc1066);
 
 /* adm1021 constants specified below */
 
@@ -45,20 +46,21 @@ I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm,
 #define ADM1021_REG_TEMP		0x00
 #define ADM1021_REG_REMOTE_TEMP		0x01
 #define ADM1021_REG_STATUS		0x02
-#define ADM1021_REG_MAN_ID		0x0FE	/* 0x41 = AMD, 0x49 = TI, 0x4D = Maxim, 0x23 = Genesys , 0x54 = Onsemi*/
-#define ADM1021_REG_DEV_ID		0x0FF	/* ADM1021 = 0x0X, ADM1023 = 0x3X */
-#define ADM1021_REG_DIE_CODE		0x0FF	/* MAX1617A */
+/* 0x41 = AD, 0x49 = TI, 0x4D = Maxim, 0x23 = Genesys , 0x54 = Onsemi */
+#define ADM1021_REG_MAN_ID		0xFE
+/* ADM1021 = 0x0X, ADM1023 = 0x3X */
+#define ADM1021_REG_DEV_ID		0xFF
 /* These use different addresses for reading/writing */
 #define ADM1021_REG_CONFIG_R		0x03
 #define ADM1021_REG_CONFIG_W		0x09
 #define ADM1021_REG_CONV_RATE_R		0x04
 #define ADM1021_REG_CONV_RATE_W		0x0A
 /* These are for the ADM1023's additional precision on the remote temp sensor */
-#define ADM1021_REG_REM_TEMP_PREC	0x010
-#define ADM1021_REG_REM_OFFSET		0x011
-#define ADM1021_REG_REM_OFFSET_PREC	0x012
-#define ADM1021_REG_REM_TOS_PREC	0x013
-#define ADM1021_REG_REM_THYST_PREC	0x014
+#define ADM1023_REG_REM_TEMP_PREC	0x10
+#define ADM1023_REG_REM_OFFSET		0x11
+#define ADM1023_REG_REM_OFFSET_PREC	0x12
+#define ADM1023_REG_REM_TOS_PREC	0x13
+#define ADM1023_REG_REM_THYST_PREC	0x14
 /* limits */
 #define ADM1021_REG_TOS_R		0x05
 #define ADM1021_REG_TOS_W		0x0B
@@ -77,14 +79,13 @@ I2C_CLIENT_INSMOD_8(adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm,
    these macros are called: arguments may be evaluated more than once.
    Fixing this is just not worth it. */
 /* Conversions  note: 1021 uses normal integer signed-byte format*/
-#define TEMP_FROM_REG(val)	(val > 127 ? (val-256)*1000 : val*1000)
-#define TEMP_TO_REG(val)	(SENSORS_LIMIT((val < 0 ? (val/1000)+256 : val/1000),0,255))
+#define TEMP_TO_REG(val)	SENSORS_LIMIT((val) / 1000, -128, 127)
 
 /* Initial values */
 
-/* Note: Even though I left the low and high limits named os and hyst, 
-they don't quite work like a thermostat the way the LM75 does.  I.e., 
-a lower temp than THYST actually triggers an alarm instead of 
+/* Note: Even though I left the low and high limits named os and hyst,
+they don't quite work like a thermostat the way the LM75 does.  I.e.,
+a lower temp than THYST actually triggers an alarm instead of
 clearing it.  Weird, ey?   --Phil  */
 
 /* Each client has this additional data */
@@ -97,12 +98,12 @@ struct adm1021_data {
 	char valid;		/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
 
-	u8	temp_max;	/* Register values */
-	u8	temp_hyst;
-	u8	temp_input;
-	u8	remote_temp_max;
-	u8	remote_temp_hyst;
-	u8	remote_temp_input;
+	s8	temp_max;	/* Register values */
+	s8	temp_hyst;
+	s8	temp_input;
+	s8	remote_temp_max;
+	s8	remote_temp_hyst;
+	s8	remote_temp_input;
 	u8	alarms;
         /* Special values for ADM1023 only */
 	u8	remote_temp_prec;
@@ -116,9 +117,6 @@ static int adm1021_attach_adapter(struct i2c_adapter *adapter);
 static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind);
 static void adm1021_init_client(struct i2c_client *client);
 static int adm1021_detach_client(struct i2c_client *client);
-static int adm1021_read_value(struct i2c_client *client, u8 reg);
-static int adm1021_write_value(struct i2c_client *client, u8 reg,
-			       u16 value);
 static struct adm1021_data *adm1021_update_device(struct device *dev);
 
 /* (amalysh) read only mode, otherwise any limit's writing confuse BIOS */
@@ -135,11 +133,12 @@ static struct i2c_driver adm1021_driver = {
 	.detach_client	= adm1021_detach_client,
 };
 
-#define show(value)	\
-static ssize_t show_##value(struct device *dev, struct device_attribute *attr, char *buf)		\
+#define show(value)							\
+static ssize_t show_##value(struct device *dev,				\
+			    struct device_attribute *attr, char *buf)	\
 {									\
 	struct adm1021_data *data = adm1021_update_device(dev);		\
-	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->value));	\
+	return sprintf(buf, "%d\n", 1000 * data->value);		\
 }
 show(temp_max);
 show(temp_hyst);
@@ -148,26 +147,29 @@ show(remote_temp_max);
 show(remote_temp_hyst);
 show(remote_temp_input);
 
-#define show2(value)	\
-static ssize_t show_##value(struct device *dev, struct device_attribute *attr, char *buf)		\
-{									\
-	struct adm1021_data *data = adm1021_update_device(dev);		\
-	return sprintf(buf, "%d\n", data->value);			\
+static ssize_t show_alarms(struct device *dev,
+			   struct device_attribute *attr,
+			   char *buf)
+{
+	struct adm1021_data *data = adm1021_update_device(dev);
+	return sprintf(buf, "%u\n", data->alarms);
 }
-show2(alarms);
-
-#define set(value, reg)	\
-static ssize_t set_##value(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)	\
-{								\
-	struct i2c_client *client = to_i2c_client(dev);		\
-	struct adm1021_data *data = i2c_get_clientdata(client);	\
-	int temp = simple_strtoul(buf, NULL, 10);		\
-								\
-	mutex_lock(&data->update_lock);				\
-	data->value = TEMP_TO_REG(temp);			\
-	adm1021_write_value(client, reg, data->value);		\
-	mutex_unlock(&data->update_lock);			\
-	return count;						\
+
+#define set(value, reg)							\
+static ssize_t set_##value(struct device *dev,				\
+			   struct device_attribute *attr,		\
+			   const char *buf, size_t count)		\
+{									\
+	struct i2c_client *client = to_i2c_client(dev);			\
+	struct adm1021_data *data = i2c_get_clientdata(client);		\
+	int temp = simple_strtoul(buf, NULL, 10);			\
+									\
+	mutex_lock(&data->update_lock);					\
+	data->value = TEMP_TO_REG(temp);				\
+	if (!read_only)							\
+		i2c_smbus_write_byte_data(client, reg, data->value);	\
+	mutex_unlock(&data->update_lock);				\
+	return count;							\
 }
 set(temp_max, ADM1021_REG_TOS_W);
 set(temp_hyst, ADM1021_REG_THYST_W);
@@ -208,35 +210,44 @@ static const struct attribute_group adm1021_group = {
 static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind)
 {
 	int i;
-	struct i2c_client *new_client;
+	struct i2c_client *client;
 	struct adm1021_data *data;
 	int err = 0;
 	const char *type_name = "";
+	int conv_rate, status, config;
 
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+		pr_debug("adm1021: detect failed, "
+			 "smbus byte data not supported!\n");
 		goto error0;
+	}
 
 	/* OK. For now, we presume we have a valid client. We now create the
 	   client structure, even though we cannot fill it completely yet.
-	   But it allows us to access adm1021_{read,write}_value. */
+	   But it allows us to access adm1021 register values. */
 
 	if (!(data = kzalloc(sizeof(struct adm1021_data), GFP_KERNEL))) {
+		pr_debug("adm1021: detect failed, kzalloc failed!\n");
 		err = -ENOMEM;
 		goto error0;
 	}
 
-	new_client = &data->client;
-	i2c_set_clientdata(new_client, data);
-	new_client->addr = address;
-	new_client->adapter = adapter;
-	new_client->driver = &adm1021_driver;
-	new_client->flags = 0;
+	client = &data->client;
+	i2c_set_clientdata(client, data);
+	client->addr = address;
+	client->adapter = adapter;
+	client->driver = &adm1021_driver;
+	status = i2c_smbus_read_byte_data(client, ADM1021_REG_STATUS);
+	conv_rate = i2c_smbus_read_byte_data(client,
+					     ADM1021_REG_CONV_RATE_R);
+	config = i2c_smbus_read_byte_data(client, ADM1021_REG_CONFIG_R);
 
 	/* Now, we do the remaining detection. */
 	if (kind < 0) {
-		if ((adm1021_read_value(new_client, ADM1021_REG_STATUS) & 0x03) != 0x00
-		 || (adm1021_read_value(new_client, ADM1021_REG_CONFIG_R) & 0x3F) != 0x00
-		 || (adm1021_read_value(new_client, ADM1021_REG_CONV_RATE_R) & 0xF8) != 0x00) {
+		if ((status & 0x03) != 0x00 || (config & 0x3F) != 0x00
+		    || (conv_rate & 0xF8) != 0x00) {
+			pr_debug("adm1021: detect failed, "
+				 "chip not detected!\n");
 			err = -ENODEV;
 			goto error1;
 		}
@@ -244,9 +255,10 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind)
 
 	/* Determine the chip type. */
 	if (kind <= 0) {
-		i = adm1021_read_value(new_client, ADM1021_REG_MAN_ID);
+		i = i2c_smbus_read_byte_data(client, ADM1021_REG_MAN_ID);
 		if (i == 0x41)
-			if ((adm1021_read_value(new_client, ADM1021_REG_DEV_ID) & 0x0F0) == 0x030)
+			if ((i2c_smbus_read_byte_data(client,
+					ADM1021_REG_DEV_ID) & 0xF0) == 0x30)
 				kind = adm1023;
 			else
 				kind = adm1021;
@@ -255,15 +267,16 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind)
 		else if (i == 0x23)
 			kind = gl523sm;
 		else if ((i == 0x4d) &&
-			 (adm1021_read_value(new_client, ADM1021_REG_DEV_ID) == 0x01))
+			 (i2c_smbus_read_byte_data(client,
+						   ADM1021_REG_DEV_ID) == 0x01))
 			kind = max1617a;
 		else if (i == 0x54)
 			kind = mc1066;
 		/* LM84 Mfr ID in a different place, and it has more unused bits */
-		else if (adm1021_read_value(new_client, ADM1021_REG_CONV_RATE_R) == 0x00
-		      && (kind == 0 /* skip extra detection */
-		       || ((adm1021_read_value(new_client, ADM1021_REG_CONFIG_R) & 0x7F) == 0x00
-			&& (adm1021_read_value(new_client, ADM1021_REG_STATUS) & 0xAB) == 0x00)))
+		else if (conv_rate == 0x00
+			 && (kind == 0 /* skip extra detection */
+			     || ((config & 0x7F) == 0x00
+				 && (status & 0xAB) == 0x00)))
 			kind = lm84;
 		else
 			kind = max1617;
@@ -286,26 +299,27 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind)
 	} else if (kind == mc1066) {
 		type_name = "mc1066";
 	}
+	pr_debug("adm1021: Detected chip %s at adapter %d, address 0x%02x.\n",
+		 type_name, i2c_adapter_id(adapter), address);
 
-	/* Fill in the remaining client fields and put it into the global list */
-	strlcpy(new_client->name, type_name, I2C_NAME_SIZE);
+	/* Fill in the remaining client fields */
+	strlcpy(client->name, type_name, I2C_NAME_SIZE);
 	data->type = kind;
-	data->valid = 0;
 	mutex_init(&data->update_lock);
 
 	/* Tell the I2C layer a new client has arrived */
-	if ((err = i2c_attach_client(new_client)))
+	if ((err = i2c_attach_client(client)))
 		goto error1;
 
 	/* Initialize the ADM1021 chip */
-	if (kind != lm84)
-		adm1021_init_client(new_client);
+	if (kind != lm84 && !read_only)
+		adm1021_init_client(client);
 
 	/* Register sysfs hooks */
-	if ((err = sysfs_create_group(&new_client->dev.kobj, &adm1021_group)))
+	if ((err = sysfs_create_group(&client->dev.kobj, &adm1021_group)))
 		goto error2;
 
-	data->class_dev = hwmon_device_register(&new_client->dev);
+	data->class_dev = hwmon_device_register(&client->dev);
 	if (IS_ERR(data->class_dev)) {
 		err = PTR_ERR(data->class_dev);
 		goto error3;
@@ -314,9 +328,9 @@ static int adm1021_detect(struct i2c_adapter *adapter, int address, int kind)
 	return 0;
 
 error3:
-	sysfs_remove_group(&new_client->dev.kobj, &adm1021_group);
+	sysfs_remove_group(&client->dev.kobj, &adm1021_group);
 error2:
-	i2c_detach_client(new_client);
+	i2c_detach_client(client);
 error1:
 	kfree(data);
 error0:
@@ -326,10 +340,10 @@ error0:
 static void adm1021_init_client(struct i2c_client *client)
 {
 	/* Enable ADC and disable suspend mode */
-	adm1021_write_value(client, ADM1021_REG_CONFIG_W,
-		adm1021_read_value(client, ADM1021_REG_CONFIG_R) & 0xBF);
+	i2c_smbus_write_byte_data(client, ADM1021_REG_CONFIG_W,
+		i2c_smbus_read_byte_data(client, ADM1021_REG_CONFIG_R) & 0xBF);
 	/* Set Conversion rate to 1/sec (this can be tinkered with) */
-	adm1021_write_value(client, ADM1021_REG_CONV_RATE_W, 0x04);
+	i2c_smbus_write_byte_data(client, ADM1021_REG_CONV_RATE_W, 0x04);
 }
 
 static int adm1021_detach_client(struct i2c_client *client)
@@ -347,19 +361,6 @@ static int adm1021_detach_client(struct i2c_client *client)
 	return 0;
 }
 
-/* All registers are byte-sized */
-static int adm1021_read_value(struct i2c_client *client, u8 reg)
-{
-	return i2c_smbus_read_byte_data(client, reg);
-}
-
-static int adm1021_write_value(struct i2c_client *client, u8 reg, u16 value)
-{
-	if (!read_only)
-		return i2c_smbus_write_byte_data(client, reg, value);
-	return 0;
-}
-
 static struct adm1021_data *adm1021_update_device(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
@@ -371,19 +372,36 @@ static struct adm1021_data *adm1021_update_device(struct device *dev)
 	    || !data->valid) {
 		dev_dbg(&client->dev, "Starting adm1021 update\n");
 
-		data->temp_input = adm1021_read_value(client, ADM1021_REG_TEMP);
-		data->temp_max = adm1021_read_value(client, ADM1021_REG_TOS_R);
-		data->temp_hyst = adm1021_read_value(client, ADM1021_REG_THYST_R);
-		data->remote_temp_input = adm1021_read_value(client, ADM1021_REG_REMOTE_TEMP);
-		data->remote_temp_max = adm1021_read_value(client, ADM1021_REG_REMOTE_TOS_R);
-		data->remote_temp_hyst = adm1021_read_value(client, ADM1021_REG_REMOTE_THYST_R);
-		data->alarms = adm1021_read_value(client, ADM1021_REG_STATUS) & 0x7c;
+		data->temp_input = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_TEMP);
+		data->temp_max = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_TOS_R);
+		data->temp_hyst = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_THYST_R);
+		data->remote_temp_input = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_REMOTE_TEMP);
+		data->remote_temp_max = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_REMOTE_TOS_R);
+		data->remote_temp_hyst = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_REMOTE_THYST_R);
+		data->alarms = i2c_smbus_read_byte_data(client,
+						ADM1021_REG_STATUS) & 0x7c;
 		if (data->type == adm1023) {
-			data->remote_temp_prec = adm1021_read_value(client, ADM1021_REG_REM_TEMP_PREC);
-			data->remote_temp_os_prec = adm1021_read_value(client, ADM1021_REG_REM_TOS_PREC);
-			data->remote_temp_hyst_prec = adm1021_read_value(client, ADM1021_REG_REM_THYST_PREC);
-			data->remote_temp_offset = adm1021_read_value(client, ADM1021_REG_REM_OFFSET);
-			data->remote_temp_offset_prec = adm1021_read_value(client, ADM1021_REG_REM_OFFSET_PREC);
+			data->remote_temp_prec =
+				i2c_smbus_read_byte_data(client,
+						ADM1023_REG_REM_TEMP_PREC);
+			data->remote_temp_os_prec =
+				i2c_smbus_read_byte_data(client,
+						ADM1023_REG_REM_TOS_PREC);
+			data->remote_temp_hyst_prec =
+				i2c_smbus_read_byte_data(client,
+						ADM1023_REG_REM_THYST_PREC);
+			data->remote_temp_offset =
+				i2c_smbus_read_byte_data(client,
+						ADM1023_REG_REM_OFFSET);
+			data->remote_temp_offset_prec =
+				i2c_smbus_read_byte_data(client,
+						ADM1023_REG_REM_OFFSET_PREC);
 		}
 		data->last_updated = jiffies;
 		data->valid = 1;