Merge tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

From Simon Horman:
Renesas USB updates for v3.11

These updates are by Sergei Shtylyov to clean-up USB support
present for R8A7779/Marzen and then extend USB support coverage to
R8A7778/BOCK-W.

* tag 'renesas-phy-rcar-usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: BOCK-W: add USB support
  ARM: shmobile: r8a7778: add USB support
  phy-rcar-usb: add R8A7778 support
  phy-rcar-usb: handle platform data
  ARM: shmobile: Marzen: pass platform data to USB PHY device
  phy-rcar-usb: add platform data
  phy-rcar-usb: correct base address
  ARM: shmobile: r8a7779: remove USB PHY 2nd memory resource
  phy-rcar-usb: remove EHCI internal buffer setup
  ARM: shmobile: r8a7779: setup EHCI internal buffer
  ehci-platform: add pre_setup() method to platform data
  ARM: shmobile: Marzen: move USB EHCI, OHCI, and PHY devices to R8A7779 code

Conflicts:
	arch/arm/mach-shmobile/board-marzen.c
	arch/arm/mach-shmobile/setup-r8a7778.c

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 93 insertions, 51 deletions

diff --git a/drivers/usb/host/ehci-platform.c b/drivers/usb/host/ehci-platform.c
index f47f2594c9d..d1f5cea435a 100644
--- a/drivers/usb/host/ehci-platform.c
+++ b/drivers/usb/host/ehci-platform.c
@@ -48,6 +48,12 @@ static int ehci_platform_reset(struct usb_hcd *hcd)
 	ehci->big_endian_desc = pdata->big_endian_desc;
 	ehci->big_endian_mmio = pdata->big_endian_mmio;
 
+	if (pdata->pre_setup) {
+		retval = pdata->pre_setup(hcd);
+		if (retval < 0)
+			return retval;
+	}
+
 	ehci->caps = hcd->regs + pdata->caps_offset;
 	retval = ehci_setup(hcd);
 	if (retval)
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 7ef3eb8617a..13c09c299f1 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -180,15 +180,15 @@ config USB_MXS_PHY
 	  MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 
 config USB_RCAR_PHY
-	tristate "Renesas R-Car USB phy support"
+	tristate "Renesas R-Car USB PHY support"
 	depends on USB || USB_GADGET
 	help
-	  Say Y here to add support for the Renesas R-Car USB phy driver.
-	  This chip is typically used as USB phy for USB host, gadget.
-	  This driver supports: R8A7779
+	  Say Y here to add support for the Renesas R-Car USB common PHY driver.
+	  This chip is typically used as USB PHY for USB host, gadget.
+	  This driver supports R8A7778 and R8A7779.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called rcar-phy.
+	  module will be called phy-rcar-usb.
 
 config USB_ULPI
 	bool "Generic ULPI Transceiver Driver"
diff --git a/drivers/usb/phy/phy-rcar-usb.c b/drivers/usb/phy/phy-rcar-usb.c
index a35681b0c50..ae909408958 100644
--- a/drivers/usb/phy/phy-rcar-usb.c
+++ b/drivers/usb/phy/phy-rcar-usb.c
@@ -1,8 +1,9 @@
 /*
  * Renesas R-Car USB phy driver
  *
- * Copyright (C) 2012 Renesas Solutions Corp.
+ * Copyright (C) 2012-2013 Renesas Solutions Corp.
  * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
+ * Copyright (C) 2013 Cogent Embedded, Inc.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -15,17 +16,41 @@
 #include <linux/platform_device.h>
 #include <linux/spinlock.h>
 #include <linux/module.h>
-
-/* USBH common register */
-#define USBPCTRL0	0x0800
-#define USBPCTRL1	0x0804
-#define USBST		0x0808
-#define USBEH0		0x080C
-#define USBOH0		0x081C
-#define USBCTL0		0x0858
-#define EIIBC1		0x0094
-#define EIIBC2		0x009C
-
+#include <linux/platform_data/usb-rcar-phy.h>
+
+/* REGS block */
+#define USBPCTRL0	0x00
+#define USBPCTRL1	0x04
+#define USBST		0x08
+#define USBEH0		0x0C
+#define USBOH0		0x1C
+#define USBCTL0		0x58
+
+/* High-speed signal quality characteristic control registers (R8A7778 only) */
+#define HSQCTL1		0x24
+#define HSQCTL2		0x28
+
+/* USBPCTRL0 */
+#define OVC2		(1 << 10) /* (R8A7779 only)			*/
+				/* Switches the OVC input pin for port 2: */
+				/* 1: USB_OVC2, 0: OVC2			*/
+#define OVC1_VBUS1	(1 << 9) /* Switches the OVC input pin for port 1: */
+				/* 1: USB_OVC1, 0: OVC1/VBUS1		*/
+				/* Function mode: set to 0		*/
+#define OVC0		(1 << 8) /* Switches the OVC input pin for port 0: */
+				/* 1: USB_OVC0 pin, 0: OVC0		*/
+#define OVC2_ACT 	(1 << 6) /* (R8A7779 only)			*/
+				/* Host mode: OVC2 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+#define PENC		(1 << 4) /* Function mode: output level of PENC1 pin: */
+				/* 1: high, 0: low			*/
+#define OVC0_ACT 	(1 << 3) /* Host mode: OVC0 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+#define OVC1_ACT	(1 << 1) /* Host mode: OVC1 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+				/* Function mode: be sure to set to 1	*/
+#define PORT1		(1 << 0) /* Selects port 1 mode:		*/
+				/* 1: function, 0: host			*/
 /* USBPCTRL1 */
 #define PHY_RST		(1 << 2)
 #define PLL_ENB		(1 << 1)
@@ -58,8 +83,10 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
 {
 	struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
 	struct device *dev = phy->dev;
+	struct rcar_phy_platform_data *pdata = dev->platform_data;
 	void __iomem *reg0 = priv->reg0;
 	void __iomem *reg1 = priv->reg1;
+	static const u8 ovcn_act[] = { OVC0_ACT, OVC1_ACT, OVC2_ACT };
 	int i;
 	u32 val;
 	unsigned long flags;
@@ -77,7 +104,16 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
 		/* (2) start USB-PHY internal PLL */
 		iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
 
-		/* (3) USB module status check */
+		/* (3) set USB-PHY in accord with the conditions of usage */
+		if (reg1) {
+			u32 hsqctl1 = pdata->ferrite_bead ? 0x41 : 0;
+			u32 hsqctl2 = pdata->ferrite_bead ? 0x0d : 7;
+
+			iowrite32(hsqctl1, reg1 + HSQCTL1);
+			iowrite32(hsqctl2, reg1 + HSQCTL2);
+		}
+
+		/* (4) USB module status check */
 		for (i = 0; i < 1024; i++) {
 			udelay(10);
 			val = ioread32(reg0 + USBST);
@@ -90,24 +126,24 @@ static int rcar_usb_phy_init(struct usb_phy *phy)
 			goto phy_init_end;
 		}
 
-		/* (4) USB-PHY reset clear */
+		/* (5) USB-PHY reset clear */
 		iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
 
-		/* set platform specific port settings */
-		iowrite32(0x00000000, (reg0 + USBPCTRL0));
-
-		/*
-		 * EHCI IP internal buffer setting
-		 * EHCI IP internal buffer enable
-		 *
-		 * These are recommended value of a datasheet
-		 * see [USB :: EHCI internal buffer setting]
-		 */
-		iowrite32(0x00ff0040, (reg0 + EIIBC1));
-		iowrite32(0x00ff0040, (reg1 + EIIBC1));
-
-		iowrite32(0x00000001, (reg0 + EIIBC2));
-		iowrite32(0x00000001, (reg1 + EIIBC2));
+		/* Board specific port settings */
+		val = 0;
+		if (pdata->port1_func)
+			val |= PORT1;
+		if (pdata->penc1)
+			val |= PENC;
+		for (i = 0; i < 3; i++) {
+			/* OVCn bits follow each other in the right order */
+			if (pdata->ovc_pin[i].select_3_3v)
+				val |= OVC0 << i;
+			/* OVCn_ACT bits are spaced by irregular intervals */
+			if (pdata->ovc_pin[i].active_high)
+				val |= ovcn_act[i];
+		}
+		iowrite32(val, (reg0 + USBPCTRL0));
 
 		/*
 		 * Bus alignment settings
@@ -134,10 +170,8 @@ static void rcar_usb_phy_shutdown(struct usb_phy *phy)
 
 	spin_lock_irqsave(&priv->lock, flags);
 
-	if (priv->counter-- == 1) { /* last user */
-		iowrite32(0x00000000, (reg0 + USBPCTRL0));
+	if (priv->counter-- == 1)	/* last user */
 		iowrite32(0x00000000, (reg0 + USBPCTRL1));
-	}
 
 	spin_unlock_irqrestore(&priv->lock, flags);
 }
@@ -147,27 +181,29 @@ static int rcar_usb_phy_probe(struct platform_device *pdev)
 	struct rcar_usb_phy_priv *priv;
 	struct resource *res0, *res1;
 	struct device *dev = &pdev->dev;
-	void __iomem *reg0, *reg1;
+	void __iomem *reg0, *reg1 = NULL;
 	int ret;
 
+	if (!pdev->dev.platform_data) {
+		dev_err(dev, "No platform data\n");
+		return -EINVAL;
+	}
+
 	res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (!res0 || !res1) {
+	if (!res0) {
 		dev_err(dev, "Not enough platform resources\n");
 		return -EINVAL;
 	}
 
-	/*
-	 * CAUTION
-	 *
-	 * Because this phy address is also mapped under OHCI/EHCI address area,
-	 * this driver can't use devm_request_and_ioremap(dev, res) here
-	 */
-	reg0 = devm_ioremap_nocache(dev, res0->start, resource_size(res0));
-	reg1 = devm_ioremap_nocache(dev, res1->start, resource_size(res1));
-	if (!reg0 || !reg1) {
-		dev_err(dev, "ioremap error\n");
-		return -ENOMEM;
+	reg0 = devm_ioremap_resource(dev, res0);
+	if (IS_ERR(reg0))
+		return PTR_ERR(reg0);
+
+	res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (res1) {
+		reg1 = devm_ioremap_resource(dev, res1);
+		if (IS_ERR(reg1))
+			return PTR_ERR(reg1);
 	}
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);